|
#1 |
Member
Join Date: Jun 2010 Location: Pondicherry Posts: 6 |
Acopos 1045 Can any one send the ACOPOS 1045 drive ERROR LED list |
|
|
|
#3 |
Member
Join Date: Aug 2011 Location: Virginia Posts: 555 |
You can also get the latest version of the manual from the B&R website: The old version won’t tell you, for instance, that a blinking green light means the drive is not in error but would be if you tried to enable it (enable input is not on, or the 3-phase power is not present).
__________________ |
|
|
|
#4 |
Member
Join Date: Jun 2010 Location: Pondicherry Posts: 6 |
Thanks dear Garry and CapinWinky… |
|
|
|
#5 |
Member
Join Date: Jun 2010 Location: Pondicherry Posts: 6 |
Thanks dear Garry |
|
|
|
#6 |
Member
Join Date: Jun 2010 Location: Pondicherry Posts: 6 |
Dear CapinWinky, Please help me, how to run the drive manually with out PLC programming like standard VFD.. |
|
|
|
#7 |
Member
Join Date: Aug 2011 Location: Virginia Posts: 555 |
You can’t run an ACOPOS without a PLC. At a minimum you must have an AC140 or AC141 plug-in PLC that goes in a drive slot.
__________________ |
|
|
Programming guidelines
Error
Name
OtFL
[Fault overtemp PTC=LI6]
PtFL
[LI6=PTC overheat]
SCF4
[IGBT short circuit]
SCF5
[Motor short circuit]
[HMI com.]
SLF3
SrF
[Torque time-out.]
SSF
[Torque/current lim]
tJF
[IGBT overtemp.]
1)
Occurs each time the controller is restarted.
338
Probable cause
•
Overheating of PTC probes detected on
input LI6
•
PTC probes on input LI6 open or short-
circuited
•
Power component fault
•
Short circuit at inverter output
•
Communication fault between the in-
verter and the graphic display terminal
•
The timeout of the torque control func-
tion has been reached
•
Switch to torque limitation
•
Inverter overheating
Error correction
•
Check load and rating of the motor.
•
Check the ventilation of the motor.
•
Let the motor cool down before switching on again.
•
Check the type and condition of the PTC sensor.
•
Check PTC probes and their motor/inverter/wiring
•
Perform a test using the
[DIAGNOSIS]
•
Examine and repair the inverter
•
Check the connection cables from the inverter to the mo-
tor and the insulation of the motor.
•
Perform the tests using the
•
Examine and repair the inverter
•
Check the terminal connection.
•
Check the timeout.
•
Check the settings for the function.
•
Inspect the condition of the mechanism.
•
Check for a mechanical problem.
•
Check the parameters
[TORQUE LIMIT]
(tLA-)
and the parameters of the fault
[CURRENT/TORQ LIMIT]
•
Check the dimensioning of the load/motor/inverter.
•
Reduce the frequency.
•
Let the motor cool down before switching on again.
ACOPOSinverter P84 User’s Manual 2.10
menu.
[DIAGNOSIS]
menu.
(tId-).
Description:
To read a parameter value from the ACOPOS, the NC manager first sends a read-request telegram from the PLC to the ACOPOS. This error is displayed if the NC manager detects that the corresponding CAN telegram has not yet been transferred to the CAN bus 70ms after the corresponding CAN send function call is made.
Описание:
Чтобы прочитать значение параметра из ACOPOS, NC-менеджер сначала посылает телеграмму-запрос-на-чтение из контроллера (ПЛК) в ACOPOS. Данная ошибка отображается если NC-менеджер обнаруживает, что соответствующая CAN-телеграмма не была передана по шине CAN после того как прошло 70мс с момента осуществления соответствующего вызова CAN-функции.
Reaction:
Resets the interface of the corresponding CAN read channel.
Реакция: (действие — зависит от контекста)
Сбрасывается интерфейс соответствующего канала чтения CAN.
Cause/Remedy:
None of the CAN nodes connected to the PLC CAN interface is active in the CAN communication so that the CAN bus acknowledge does not occur after sending the CAN telegram.
Network connection interruption or failure of all ACOPOS devices.
Причина/Средство исправления:
Ни один из узлов CAN, соединенных с интерфейсом ПЛК CAN, не является активным в CAN связи, таким образом, что, подтверждение шины CAN не возникает (не происходит / не имеет места) после отправки CAN-телеграммы.
Сам я мало что понимаю в промышленных сетях (CAN и т.п.), поэтому перевод может быть не вполне корректный.