An error occurred inside the solver module general error ansys

Ошибка: «An error occurred inside the SOLVER module: general error.» Что делать?

Ребят, внимание вопрос!)

Установил Ansys 14.5.7, счастливо считал в нём раму для велосипеда несколько недель. Вчера Ансис перестал считать. Через некоторое время после запуска расчёта выдаёт ошибку (видимо, когда решение начинается):

An error occurred inside the SOLVER module: general error.

Напротив Солвинга молнии красные, ничего не считает. Такая же ошибка и при расчёте рамы, и простого стержня, который просто для теста нарисовал.

Я так понял, что произошла какая-то поломка прям в программе, может быть, хотя непонятно как это так получиться могло, может и не так) Может я какие-то настройки решения меняю, хотя ничего специально не менял и всё считал так же,

Установил Ансис 15.0. Тестовый стержень посчитал один раз, при попытке посчитать раму выдал такую же ошибку и опять не считает вообще ничего. И теперь это через пару часов после установки. Что с этим делать?(

Тестировать железо на предмет поломки: память, процессор, материнская плата, жесткий диск. Также посмотреть *.err в папке решения и посмотреть что там пишеться.

Аааа. Спасибо ОГРОМНОЕ!

Прочитал файл ошибки:
/COM,ANSYS RELEASE 14.5.7 UP20130316 19:34:18 02/20/2014 *** FATAL *** CP = 1.844 TIME= 19:34:21 An error has occurred when trying to check for any GPU devices. Error code = 35 which translates to: CUDA driver version is insufficient for CUDA runtime version. Please check your GPU device driver level and verify that a supported GPU device has been installed correctly. ************************************************************************ The above error is non-recoverable by ANSYS ANSYS run terminated by the indicated error Current data base saved if possible. ************************************************************************Я ускорение с помощью видюхи поставил. Вначале работало, потом перестало почему-то, значит. Ускорение видюхой отключил — сразу же всё считать начало! Ещё раз огромное спасибо, уж и не знал, что делать.

Хм. Так это получается видюха отвалилась, чтоли, как-то. Драйвер переустановить надо, чтоли

У вас квадра установлена?

Хм, что в данном случае понимается под словом квадра?

NVIDIA Quadro. Линейка проффесиональных видеокарт от NVIDIA. Прочитайте раздел помощи // Installation and Licensing Documentation // Windows Installation Guide // 1. Installation Prerequisites for Windows // 1.4. GPU Requirements прежде чем включать GPU ускорение. Игровые видеокарты не поддерживаются

Источник

An error occurred inside the solver module: general error

I’m setting up simulation with Ansys LS-Dyna in 19.2 version. However each time I try to solve the simulation it’s give me error massage

«An error occurred inside the solver module: general error»

How does overcome this. I’m really fed-up testing with simple to FEA setting and trying solved. No luck each time gave me this error massage.

This is most common error, and it’s most of the time happen due to

• Incorrectly define material data
• Incorrect mesh size or mesh pattern
• Involving in large deformation/Non-linear behavior
• Load -Boundary condition & time stepping

As common good practice do the following changes ang you get lucky enough to get solution.

Static Structural

1. Simplify the model as much as possible and remove the unwanted section or features that are not affect to analysis.
2. Check the material model. Whether material data correctly defined and all the require material data defined for the analysis type.
3. For initial test analysis scale down the model or get the half or section depending on the symmetric and start getting result. Then you can expand the FEA setting for actual model/or section.
4. Define the mesh size and element order based on solver, analysis type, model, Try to use Multizone meshing
5. Check for the contacts/contacts types and evaluate the initial contact setting with «Contact Tools» correct them
6. If the one body undergo a displacement, then split the analysis time to small interval and define the displacement for that particular time interval. (ex if the analysis time is 0.001 and displacement 10 mm, then split the time 0.0001, 0.0002,0.0003. 0.001 and displacement 1 mm, 2 mm, 3 mm. 10 mm)
7. For non-linear simulation, it’s always better to have Finer mesh
8. Set ON for Large Deflection
9. Set the 0.0001s «End Time» and with result fine tune
10. If the one section or body undergo a large deformation, and you are doing Static Structural Simulation define the, «Nonlinear Adaptive Region» Nonlinear Control -> Newton-Raphson Option ->Unsymmetrical & Nonlinear Control -> Stabilization -> ON
11. Use the «Automatic Mass Scaling -> ON» and keep the total mass scaling less than 5% for accuracy
12. Start with Program Controlled setting if you don’t know the really what setting need to set and expand the correct setting when evolve the solution

Sometimes some of the Explicitly Dynamic, LS-Dyna solution can be archive via Statics Structural method. But it’s always not easy.

Explicit Dynamic / Ansys LS-Dyna

1. Simplify the model as much as possible and remove the unwanted section or features that not affect to analysis.
2. Check the material model. Whether material data correctly defined and all the require material data defined for the analysis type. For LS-Dyna / or Explicit dynamic make sure failure criteria defined.
3. Define the mesh size and element order based on solver, analysis type, model.
4. For non-linear simulation, it’s always better to have Finer mesh
5. coarse mesh used to to gain the insight
6. Set the 0.01s «End Time» and with result fine tune
7. If you are running Explicitly Solver, assign the element erode card
8. Use the «Automatic Mass Scaling -> ON» and keep the total mass scaling less than 5% for accuracy

Источник

Update failed for the Solution component in System Coupling

1. Я новичок в ANSYS

2. Решаю задачу двусторонней связи деформации ленты от давления жидкости (воды)

4. С ошибкой в прошлый раз мне помогли! Спасибо! http://cae-club.ru/forum/problema-s-mesh

5. При старте расчета появляется следующая ошибка:

1. Error! Update failed for the Solution component in System Coupling. The coupled update for System, Transient Structural, threw an exception. D3 06.12.2015 19:02:03
2. Error! System coupling run completed with errors. System Coupling Service reported: System coupling run aborted by user or due to fatal error: Please do not save the project if you would like to recover to the last saved state. 06.12.2015 19:00:38
3. Error! A solver failure occurred during the run in the Transient Structural system 06.12.2015 19:00:34
4. Error! An error occurred inside the SOLVER module: general error. 06.12.2015 19:00:30
5. Error! An unexpected error has occurred: The given key was not present in the dictionary. 06.12.2015 19:00:06

6. В Transient Structural написано следующе:

*** FATAL *** CP = 0.922 TIME= 19:00:29
MAPDL is unable to connect to the system coupling service on
telecommand.telemetry.microsoft.com through port 49750. Please check
ANSYS execution options -schost and -scport for a System Coupling
analysis and ensure that the host name and the port number are
correct.

*** FATAL ***
Random read error on unit= 16 possible corrupt or missing file.
I/O status error= 0

Источник

Thanks. We have received your request and will respond promptly.

Come Join Us!

• Talk With Other Members
• Be Notified Of Responses
  To Your Posts
• Keyword Search
• One-Click Access To Your
  Favorite Forums
• Automated Signatures
  On Your Posts
• Best Of All, It’s Free!

Posting Guidelines

Promoting, selling, recruiting, coursework and thesis posting is forbidden.

An error occurred while starting the solver module Ansys problem

An error occurred while starting the solver module Ansys problem

An error occurred while starting the solver module Ansys problem

I am using Ansys 18 on my PC and I was trying to rerun a simulation I had already solved. And I am getting the error «an error occurred while starting the solver module»
I tried everything I could but it is not running on my PC.

I completely reinstalled ANSYS (Deleted every file by going in safe mode) still the error is there. I can’t even run a simple problem such as a rectangular beam with an axial load.
I have around 40Gb space in C and 80 Gb in D drive (where files are saved).
I checked Virtual memory settings and they were as before, around 10Gb allotted.

I can run the same problem in another PC.

RE: An error occurred while starting the solver module Ansys problem

After searching online, it seems one of the following causes of error and possible solution but I am not sure. And yes this might be the error due to solver file issues which might be modified after system/version upgrade or corruption —

— For student version, node count greater than allowed might cause this error.
— Search help documentation -Mechanical Application => Mechanical User’s guide => Troubleshooting => Problem Situation. There is description about this problem. Check that.
— Make sure you have all the file names and folder names in English/as per naming rules
-Check out the solve.out file in solver directory (RMB click on the Solutions and open solver files directly) for any possible errors
-Formatting the installation drive and Ansys reinstallation (Which you already did, I guess)
-Renaming the C:Users AppDataRoamingAnsys vXX file to vXX.old
-check the name references for the loads and boundary conditions, named selection sets, sets which may be modified when you converted from previous version
-Start MAPDL. If you get any error wrt «libifcoremd.dll», then rename the the same file in c:WindowsSystem32 and c:WindowsSysWOW64 with .old extension. try running MAPDL and then mechanical.
— Go to Tools => Solve process settings=>Advanced=>tick off the distributed solver and GPU acceleration to None and then run the analysis
— Are you saving your project to a network drive or OneDrive folder? Try saving on local drive and then run.

If you still get the error, you may need to contact Ansys local support.

RE: An error occurred while starting the solver module Ansys problem

RE: An error occurred while starting the solver module Ansys problem

Quote (tsram90)

-Did you format the installation drive or do complete reinstall of windows OS?
-If the MAPDL is starting without any issue then try and run a simple problem in MAPDL first and then try another problem in Workbench. If MAPDL is working without any error then why there is «solver» error? It should work without any error cause Mechanical uses same MAPDL solver.
-Check if there is any license issue.

If nothing is working, you need to connect with Ansys support.

Red Flag Submitted

Thank you for helping keep Eng-Tips Forums free from inappropriate posts.
The Eng-Tips staff will check this out and take appropriate action.

Reply To This Thread

Posting in the Eng-Tips forums is a member-only feature.

Click Here to join Eng-Tips and talk with other members! Already a Member? Login

Источник

Thanks. We have received your request and will respond promptly.

Come Join Us!

• Talk With Other Members
• Be Notified Of Responses
  To Your Posts
• Keyword Search
• One-Click Access To Your
  Favorite Forums
• Automated Signatures
  On Your Posts
• Best Of All, It’s Free!

Posting Guidelines

Promoting, selling, recruiting, coursework and thesis posting is forbidden.

ANSYS Workbench Simulation Solver Error

ANSYS Workbench Simulation Solver Error

ANSYS Workbench Simulation Solver Error

Here’s the jist of the problem:
I modelled a solid O-ring. I fixed one face and applied pressure on another face. I clicked Solve, and it gave me an error. The window gave the message: «An Error Occurred While Starting the ANSYS Solver Module» and told me to check the ANSYS troubleshooting section in the manual. The manual suggests that I increase my virtual memory or move the temporary files to a new space where I will have enough disk space.
The thing is, I already have my virtual memory set at 8GB and my computer specs are as follows:

-2GB RamCPU Intel Core 2 Duo Conroe E6400 2.13GHz FSB 1066, 2MB CPU
-Memory 2048MB DDR II 667 Memory 240 Pin (1024 x 2)
-Motherboard ASUS P5N SLI Motherboard
-Western Digital 250GB 7200RPM 8MB Cache Serial ATA II
-(2x)SLI Video eVGA GeForce 7900 GS PCI-E 256MB DDR3 DVI. HDTV

It’s a gaming rig and I am pretty sure I have more than enough to run/store the files. All my ANSYS workbench settings are at default. Any help would be appreciated. Thanks.

RE: ANSYS Workbench Simulation Solver Error

RE: ANSYS Workbench Simulation Solver Error

RE: ANSYS Workbench Simulation Solver Error

Hmmmm that’d odd. How many DOF’s is your model? If you’re modeling an o-ring why don’t you make it axisymmetric? Your run time and file sizes will be many times smaller.

RE: ANSYS Workbench Simulation Solver Error

RE: ANSYS Workbench Simulation Solver Error

Can you run any of the Ansys test/demo jobs on your machine ? Maybe the error is not specific to your o-ring problem.

RE: ANSYS Workbench Simulation Solver Error

I can model parts with no problems, but when I modelled a solid cube or imported some part drawings from CATIA and tried to do some of the simulation tests (i.e. with a simple clamp + force), it still gave me the same errors.

When I try to generate a volume mesh in CFX on a simple part drawn in DesignModeler, it gives me 4 errors. They’re stated as follows:

1) The location F1604.2024,F1605.2024, etc. refers to # primitive regions that do not appear in the geometry. These regions are: F1621.2024, F1847.2024, etc.

2) There was a problem processing the location of the face spacing
Default Face Spacing

3)Because of the problems with the face spacing «Default Face Spacing»
it is being ignored.

4)Unable to identify the default body spacing «Default Face Spacing» referred to
in the «Default Face Spacing» parameter of the «Default/SPACING» spacing object.

So only my Designmodeler works. Simulation & CFX does not. Is it my settings?

Red Flag Submitted

Thank you for helping keep Eng-Tips Forums free from inappropriate posts.
The Eng-Tips staff will check this out and take appropriate action.

Reply To This Thread

Posting in the Eng-Tips forums is a member-only feature.

Click Here to join Eng-Tips and talk with other members! Already a Member? Login

Источник

Approved: ASR Pro

Speed up your computer’s performance now with this simple download.

Over the past week, some of our users have informed us that they have encountered an ANSYS error in their troubleshooter.

I am practicing this simulation again and the experts say the bug is gone. But most of the errors will still show up as shown below.

But when I think about this search error file, the “ProjectScratch” file cannot be found on my computer.

*** WARNING *** Time = 21 : 02
Checking items is currently inactive. SHPP, ON or SHPP, WARN successfully withdrawn, re-activation if desired

Note that PC = 21:10:02
Confirmed model exploration and publication completion warning were found C: Users 76061 AppData Local Temp WB_DESKTOP-UIJ6GDS_123_25300_2
ectScratch ScrED20 file0.err) for this warning tweet.

I’m not a CZM expert, but you’ve made a few mistakes.

Make sure you are using a 2D deformation systemand planes, that’s ok, but you haven’t set 2D type of geometry cell analysis in Workbench.

You cannot simply change this value to 2D. This must be done before attaching geometry to the cell model. Start a new model and do it.

You have a fractured limb indicating a contact peel that helps anchor the contact area, which is generally normal.

The problem is that you have selected faces of 2D solids that need to be connected. Usually you should have the edges selected. This was not in your model because the analysis type was 3D.

Another problem is that you did not choose the glue joint slot as the medium for flexible and rigid adhesives. You should probably use a linked contact.

I have repaired these machines, but your geometry is too large in resolution for students. The attached file contains 127 thousand nodes, and the license contains 32 thousand nodes. Just cut 3/4 of the length of the beam, but you will. You can also provide rigid parts with Rigid routines so that they only need to be connectedto with one edge. Replace the fixed mount with a remote offset.