Модератор: vetal
svzhuk » Чт окт 06, 2016 11:26 pm
Если у одного человека есть воображаемый друг, то он — ненормальный. Если же у кучи людей есть воображаемый друг, то это религия.
с 01.03.2017 свалил в Польшу до ~~~
-
svzhuk
- Засыпщик
-
- Персональный альбом
Signaller » Пт окт 07, 2016 4:50 pm
Собрал нормально вроде, но выдаёт ошибку и даже не пытается ролики прокрутить.(
Разъёмы включены точно правильно, фоткал при разборке.
Добавлено спустя 50 минут 40 секунд:
Выяснил ошибку E7330000, E733 0005
-
Signaller
- Осматривается
-
-
-
Canon G1010 series, G2010 series, G3010 series, G4010 series
Verter в форуме Файлообменник
- 0
- 3319
Verter
Ср авг 19, 2020 12:00 pm
-
Canon G1010 series, G2010 series, G3010 series, G4010 series
-
-
Canon IR 2018 выдает ошибку «out of toner change toner»
Sveterkom в форуме Принтеры, МФУ, копиры формата A3
- 11
- 9660
Goldwater
Чт окт 08, 2020 11:29 pm
-
Canon IR 2018 выдает ошибку «out of toner change toner»
-
-
Canon G1000 series, G2000 series, G3000 series Service Manua
Verter в форуме Файлообменник
- 10
- 5523
Azelus
Пт июн 12, 2020 4:46 am
-
Canon G1000 series, G2000 series, G3000 series Service Manua
-
-
Canon IR 3225 «засыпает»
johnnybravo в форуме Принтеры, МФУ, копиры формата A3
- 4
- 6999
johnnybravo
Пн июл 23, 2012 1:32 pm
-
Canon IR 3225 «засыпает»
-
-
Canon mf635cx ошибка «замятие»
belocarsk в форуме Принтеры, МФУ, факсы, копиры формата A4
- 8
- 4991
belocarsk
Пн мар 04, 2019 12:23 pm
-
Canon mf635cx ошибка «замятие»
Вернуться в Принтеры, МФУ, факсы, копиры формата A4
Кто сейчас на форуме
Сейчас этот форум просматривают: нет зарегистрированных пользователей и гости: 92
301 Views 0
Canon-imageRUNNER-2270 E733 0000 Error Code Instructions
Below you will find the service manual information for the Canon-imageRUNNER-2270 E733 0000 Error Code along with additional details to explain what can cause the problem and followed by solutions that might help you fix it. If I have additional information from past experiences I will try to add it.
Service Manual Instructions for the Canon-imageRUNNER-2270 E733 0000 Error Code
E733 0000
Description :
There is an error in the communication with the printer.
Causes :
At startup, communication with the printer fails.
Solutions :
1. Check the connector used to connect to the printer.
2. Check the power supply of the printer (to see if initialization takes place at startup).
3. Replace the DC controller or the main board.
If you are looking over this article and have experience with this fault and would like to make a contribution please be sure to leave a comment down below. Or, if you have read this article and have further questions then ask. If I have exposure to the trouble then I will reply.
Do not forget, not every error is exactly alike. What treats the situation one occasion might not fix it the next time. While the tips in this text obtain from the service manual and in most cases ought to get your equipment operational, now and again additional circumstances might be in play.
Thanks: 0
Likes: 0
Dislikes: 0
-
02-02-2016
#1
Senior Tech
100+ Posts
- Rep Power
- 20
Canon c5030 displays the error E733-0000. Entering service mode the only button available is Copier, all others have disappeared from the screen. Going into function > clear > ERR (or anything else) the machine freezes. This started right after a P Print which only partially printed.
Following the manual I replaced main controller 2, haven’t replaced dc controller yet.
-
02-03-2016
#2
Re: c5030, E733-0000
Did you upgrade the software??
Practice makes perfect
If it ain’t broke, don’t fix it
A picture is worth a thousand words
If you want something done right, you have to do it yourself
-
02-03-2016
#3
Senior Tech
100+ Posts
- Rep Power
- 20
Re: c5030, E733-0000
Originally Posted by zoraldinho
Did you upgrade the software??
No, I haven’t upgraded software or firmware. I recall seeing a post that mentioned a software upgrade fixed this error.
-
02-03-2016
#4
Senior Tech
100+ Posts
- Rep Power
- 20
Re: c5030, E733-0000
Originally Posted by cscce
No, I haven’t upgraded software or firmware. I recall seeing a post that mentioned a software upgrade fixed this error.
I have SST but I need the c5030 system software. Unfortunately network security at the machine’s location seems to be interfering with connections to Canon’s servers. I can download from my office. I just need the link. On the other hand, I have 5 more c5030’s. Can the software be copied from one of them to a pc and then copied onto the problem machine?
Many thanks.
Last edited by cscce; 02-03-2016 at 11:23 PM.
-
02-04-2016
#5
Technician
- Rep Power
- 15
Re: c5030, E733-0000
Originally Posted by cscce
Canon c5030 displays the error E733-0000. Entering service mode the only button available is Copier, all others have disappeared from the screen. Going into function > clear > ERR (or anything else) the machine freezes. This started right after a P Print which only partially printed.
Following the manual I replaced main controller 2, haven’t replaced dc controller yet.
Think about what you done before the error occur. I remember once a broke a cable which seem contact the metal frame causing a similar issue.
If you do not know. Try to boot the machine with unplug one cabel connecting to sensors or other componets each time form the DC control Board, if a different error code shows. Check the cable you unplug.
-
02-04-2016
#6
Technician
- Rep Power
- 15
Re: c5030, E733-0000
Think about what you done before the error occur. I remember once a broke a cable which seem contact the metal frame causing a similar issue.
If you do not know. Try to boot the machine with unplug one cabel connecting to sensors or other componets each time form the DC control Board, if a different error code shows. Check the cable you unplug.
-
02-09-2016
#7
Senior Tech
100+ Posts
- Rep Power
- 20
Re: c5030, E733-0000
Problem solved. It was the Relay Board (FM3-7935-000).
Many thanks to MrB for posting this solution back in 2014.
-
02-10-2016
#8
Re: c5030, E733-0000
Practice makes perfect
If it ain’t broke, don’t fix it
A picture is worth a thousand words
If you want something done right, you have to do it yourself
Tags for this Thread
Bookmarks
Bookmarks
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
- BB code is On
- Smilies are On
- [IMG] code is On
- [VIDEO] code is On
- HTML code is Off
Forum Rules
E732-0F23-04
Detection Description
Remedy
E733-0000-05
Detection Description
Remedy
E733-0001-05
Detection Description
Remedy
E733-0002-05
Detection Description
Remedy
Communication error
Communication error that can be recovered by reboot
If it is detected again immediately after reboot, E732-0023 is generated.
It is not necessary to perform a remedy because the machine is automatically rebooted after log
collection.
Printer communication error
A communication error between the DC Controller PCB and the Main Controller PCB was detected
at startup.
[Related parts]
— Harness between the DC Controller PCB (UN049/J110) and the Main Controller PCB (UN05/
J4511)
— DC Controller PCB (UN049)
— Main Controller PCB (UN05)
[Remedy] Check/replace the related harness/cable, connector and parts.
[Reference]
— Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and
restore the backup data after the replacement so the data may be able to be protected.
— Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP
— Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES
— Before replacing the Main Controller PCB, back up the service mode data (approx. 2 min) and
restore the backup data after the replacement so the data may be able to be protected.
— Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMBUP
— Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMRES
Printer communication error
A communication error between the DC Controller PCB and the Main Controller PCB was detected.
[Related parts]
— Harness between the DC Controller PCB (UN049/J110) and the Main Controller PCB (UN05/
J4511)
— DC Controller PCB (UN049)
— Main Controller PCB (UN05)
[Remedy] Check/replace the related harness/cable, connector and parts.
[Reference]
— Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and
restore the backup data after the replacement so the data may be able to be protected.
— Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP
— Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES
— Before replacing the Main Controller PCB, back up the service mode data (approx. 2 min) and
restore the backup data after the replacement so the data may be able to be protected.
— Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMBUP
— Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMRES
Printer communication error
Signal error was detected after establishment of communication between the DC Controller PCB
and the Main Controller PCB.
[Related parts]
— Harness between the DC Controller PCB (UN049/J110) and the Main Controller PCB (UN05/
J4511)
— DC Controller PCB (UN049)
— Main Controller PCB (UN05)
[Remedy] Check/replace the related harness/cable, connector and parts.
[Reference]
— Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and
restore the backup data after the replacement so the data may be able to be protected.
— Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP
— Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES
— Before replacing the Main Controller PCB, back up the service mode data (approx. 2 min) and
restore the backup data after the replacement so the data may be able to be protected.
— Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMBUP
— Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMRES
453
7. Error/Jam/Alarm