Подробнее устранение неисправностей описано в руководстве по эксплуатации каждой модели.
На нашем сайте представлены запасные части для оборудования Carel.
Для подбора запасных частей Carel сообщите нам полную маркировку блока и наименование запчасти любым удобным способом.
Коды ошибок управляющих блоков для систем вентиляции и кондиционирования Carel (PCOxs электро)
Код | Описание ошибки |
---|---|
E01 | Поступил сигнал от пожарной сигнализации |
E02 | Неисправен датчик наружной температуры |
E03 | Неисправен датчик температуры в помещении |
E04 | Неисправен датчик температуры приточного воздуха |
E05 | Неисправен датчик температуры возвращаемого теплоносителя |
E08 | Неисправен датчик температуры возвращаемого теплоносителя после нагревателя второго нагрева |
E09 | Неисправен датчик влажности приточного воздуха |
E10 | Неисправен датчик влажности воздуха в помещении |
E12 | Неисправен датчик температуры насыщения |
E13 | Один или несколько аналоговых входов под ручным управлением |
E14 | Один или несколько аналоговых выходов под ручным управлением |
E15 | Один или несколько дискретных входов под ручным управлением |
E16 | Один или несколько дискретных выходов под ручным управлением |
E17 | Нет сигнала статуса от приточного вентилятора |
E18 | Нет сигнала статуса от вытяжного вентилятора |
E19 | Нет сигнала статуса от вытяжного и (или) приточного вентилятора |
E20 | Низкая наружная температура для использования режима «лето» |
E21 | Запуск заблокирован. Низкая температура возвращаемого теплоносителя или клапан в контуре нагревателя открыт менее чем на 80% (или иное значения согласно St13) |
E22 | Защита от замерзания водяного нагревателя. Предварительная тревога |
E23 | Защита от замерзания водяного нагревателя. Основная тревога |
E24 | Неисправен насос в контуре водяного нагревателя |
E25 | Защита от замерзания водяного нагревателя второго нагрева. Предварительная тревога |
E26 | Защита от замерзания водяного нагревателя второго нагрева. Основная тревога |
E27 | Неисправен насос в контуре водяного нагревателя 2 |
E28 | Перегрев электронагревателя |
E29 | Активировано оттаивание рекуператора |
E30 | Неисправен привод ротора рекуператора |
E31 | Неисправен компрессорно-конденсаторный агрегат (ККА) |
E32 | Фильтр на притоке загрязнен |
E33 | Фильтр на вытяжке загрязнен |
E34 | Фильтр загрязнен |
E37 | Отсутствует связь с платой расширения |
E39 | Получен внешний сигнал тревоги |
E40 | Перезапуск после подачи питания |
E41 | Термозащита приточного вентилятора |
E42 | Термозащита вытяжного вентилятора |
E43 | Термозащита вентиляторов |
-
Bookmarks
Quick Links
Updated:
17/03/2010
CAREL ir33
Q u i c k r e f e r e n c e H a n d b o o k
Ver. 1.1
Pag.1/12
Eng
Related Manuals for Carel ir33
Summary of Contents for Carel ir33
-
Page 1
Updated: 17/03/2010 CAREL ir33 Q u i c k r e f e r e n c e H a n d b o o k Ver. 1.1 Pag.1/12… -
Page 2: Main Features Of The Instrument
Updated: 17/03/2010 MAIN FEATURES OF THE INSTRUMENT USER INTERFACE ON/OFF switch button – UP button to increase temperature values DOWN button to decrease values — Activates/deactivates the manual defrost SET temperature button Prg/mute button Malfunctioning or failure warning icon High/Low temperature alarm icon icon is ON when defrost process starts icon is ON when compressor starts icon is ON when evaporator fans starts…
-
Page 3
“0” that indicates the password prompt Press UP button to set the password – CAREL thermoregulators are provided with password set to 11 (the code of the password allows access to the configuration parameters) -
Page 4
Updated: 17/03/2010 MANUAL Manual defrost is activated or deactivated if DEF/DOWN button is keep DEFROST pressed more than 5 seconds. When defrost starts display shows dFb (defrost begining) Defrost’s warning icon is ON when defrost is active Defrost can be interrupted simply by pressing again the DEF/DOWN button more than 5 seconds. -
Page 5
Updated: 17/03/2010 HOW TO CHECK To check current temperature measured by a single installed probe, CAVITY PROBE proceeds as follow: TEMPERATURE 1. refers to the previous step how to get in the configuration parameter session — type C parameter 2. scroll the configuration parameter list, by using UP/DOWN buttons, until display shows the parameter /C1 (calibration or offset for cavity probe) 3. -
Page 6
Updated: 17/03/2010 TABLE OF OPERATING PARAMETERS N° Code Range U.M. Description TEMPERATURE PROBE MANAGEMENT PARAMETERS 0…15 Measurement stability 0…15 Probe display response 0…100 Virtual probe Flag Selection °C or °F Flag Decimal point 1…6 Display on terminal 0…6 Display on external terminal 0…2 Type of probe 0…3… -
Page 7
Updated: 17/03/2010 N° Code Range U.M. Description 0…1 Flag Enable autostart function in PD 0…1 Flag Select Pump down by time or pressure 0…250 Seconds Second compressor delay DEFROST MANAGEMENT PARAMETERS 0…4 Flag Type of defrost 0…250 Hours Interval between defrosts -50…200 °C/°F End defrost temperature, evaporator… -
Page 8
Clean Alarm counter reset NOTE 1: Above operating parameters are available for all range of CAREL thermoregulators. Particularly all green highlighted parameters are available on new CAREL controller ir33 IRELF0HN245, currently installed on HD cabinets and counters NOTE 2: Blu highlighted operating parameters listed above are not influential for the functioning of the appliance. -
Page 9
Updated: 17/03/2010 SERVICE ALLARMS AND SIGNALS SERVICE ALARMS SERVICE ALARMS DUE TO MALFUNCTIONING OR FAILURE PRODUCE A WARNING SIGNALS ON THE DISPLAY BY MEAN OF THE SERVICE ICON CAVITY PROBE In case of cavity probe faulty or malfunctioning display shows the error FAULT signal rE and E0 (cavity probe S1 fault) alternately The appliance works however and compressor starts are controlled by… -
Page 10
Updated: 17/03/2010 TEMPERATURE ALARMS AND SIGNALS TEMPERATURE HIGH OR LOW TEMPERATURE ALARMS DUE TO MALFUNCTIONING OR ALARMS COMPONENTS FAILURE PRODUCE A WARNING SIGNALS ON THE DISPLAY BY MEAN OF THE ALARM ICON In case of low cavity temperature, referred to the cavity probe, the TEMPERATURE display shows a flashing error code LO. -
Page 11
Updated: 17/03/2010 CONNECTIONS Follows all electrical connections available on ir33 CAREL controller , currently used in production IRELC0HN215 (646R05100) installed on STD BEN and CL freezer counter and STD BEN cabinet provided with internal light IRELF0EN215 (646R04700) installed on all STD BEN refrigerated counters, 400Lt refrigerated cabinets and all STD BEN cabinets without light Ver. -
Page 12
Updated: 17/03/2010 IRELF0HN245 (646R09300) installed on HD counters and cabinets IRELF0EN225 installed on digital ROLL–IN IRELF0EHD15 installed on 400Lt FREEZER cabinet Ver. 1.1 Pag.12/12…
-
Bookmarks
Quick Links
Updated:
17/03/2010
CAREL ir33
Q u i c k r e f e r e n c e H a n d b o o k
Ver. 1.1
Pag.1/12
Eng
Related Manuals for Carel ir33
Summary of Contents for Carel ir33
-
Page 1
Updated: 17/03/2010 CAREL ir33 Q u i c k r e f e r e n c e H a n d b o o k Ver. 1.1 Pag.1/12… -
Page 2: Main Features Of The Instrument
Updated: 17/03/2010 MAIN FEATURES OF THE INSTRUMENT USER INTERFACE ON/OFF switch button – UP button to increase temperature values DOWN button to decrease values — Activates/deactivates the manual defrost SET temperature button Prg/mute button Malfunctioning or failure warning icon High/Low temperature alarm icon icon is ON when defrost process starts icon is ON when compressor starts icon is ON when evaporator fans starts…
-
Page 3
“0” that indicates the password prompt Press UP button to set the password – CAREL thermoregulators are provided with password set to 11 (the code of the password allows access to the configuration parameters) -
Page 4
Updated: 17/03/2010 MANUAL Manual defrost is activated or deactivated if DEF/DOWN button is keep DEFROST pressed more than 5 seconds. When defrost starts display shows dFb (defrost begining) Defrost’s warning icon is ON when defrost is active Defrost can be interrupted simply by pressing again the DEF/DOWN button more than 5 seconds. -
Page 5
Updated: 17/03/2010 HOW TO CHECK To check current temperature measured by a single installed probe, CAVITY PROBE proceeds as follow: TEMPERATURE 1. refers to the previous step how to get in the configuration parameter session — type C parameter 2. scroll the configuration parameter list, by using UP/DOWN buttons, until display shows the parameter /C1 (calibration or offset for cavity probe) 3. -
Page 6
Updated: 17/03/2010 TABLE OF OPERATING PARAMETERS N° Code Range U.M. Description TEMPERATURE PROBE MANAGEMENT PARAMETERS 0…15 Measurement stability 0…15 Probe display response 0…100 Virtual probe Flag Selection °C or °F Flag Decimal point 1…6 Display on terminal 0…6 Display on external terminal 0…2 Type of probe 0…3… -
Page 7
Updated: 17/03/2010 N° Code Range U.M. Description 0…1 Flag Enable autostart function in PD 0…1 Flag Select Pump down by time or pressure 0…250 Seconds Second compressor delay DEFROST MANAGEMENT PARAMETERS 0…4 Flag Type of defrost 0…250 Hours Interval between defrosts -50…200 °C/°F End defrost temperature, evaporator… -
Page 8
Clean Alarm counter reset NOTE 1: Above operating parameters are available for all range of CAREL thermoregulators. Particularly all green highlighted parameters are available on new CAREL controller ir33 IRELF0HN245, currently installed on HD cabinets and counters NOTE 2: Blu highlighted operating parameters listed above are not influential for the functioning of the appliance. -
Page 9
Updated: 17/03/2010 SERVICE ALLARMS AND SIGNALS SERVICE ALARMS SERVICE ALARMS DUE TO MALFUNCTIONING OR FAILURE PRODUCE A WARNING SIGNALS ON THE DISPLAY BY MEAN OF THE SERVICE ICON CAVITY PROBE In case of cavity probe faulty or malfunctioning display shows the error FAULT signal rE and E0 (cavity probe S1 fault) alternately The appliance works however and compressor starts are controlled by… -
Page 10
Updated: 17/03/2010 TEMPERATURE ALARMS AND SIGNALS TEMPERATURE HIGH OR LOW TEMPERATURE ALARMS DUE TO MALFUNCTIONING OR ALARMS COMPONENTS FAILURE PRODUCE A WARNING SIGNALS ON THE DISPLAY BY MEAN OF THE ALARM ICON In case of low cavity temperature, referred to the cavity probe, the TEMPERATURE display shows a flashing error code LO. -
Page 11
Updated: 17/03/2010 CONNECTIONS Follows all electrical connections available on ir33 CAREL controller , currently used in production IRELC0HN215 (646R05100) installed on STD BEN and CL freezer counter and STD BEN cabinet provided with internal light IRELF0EN215 (646R04700) installed on all STD BEN refrigerated counters, 400Lt refrigerated cabinets and all STD BEN cabinets without light Ver. -
Page 12
Updated: 17/03/2010 IRELF0HN245 (646R09300) installed on HD counters and cabinets IRELF0EN225 installed on digital ROLL–IN IRELF0EHD15 installed on 400Lt FREEZER cabinet Ver. 1.1 Pag.12/12…