LG CH-01 Неисправность одного из терморезисторов платы (разрыв или короткое замыкание) внутреннего комнатного, настенного блока сплит системы – контроля температуры поступающего воздуха и трубки газового контура кондиционера
LG CH-02 Неисправность одного из терморезисторов (разрыв или короткое замыкание) наружного блока: датчика температуры поступающего воздуха или температуры трубки газового контура
LG CH-03 Кондиционер работает одновременно и на обогрев и на охлаждение воздуха
LG CH-04 Включена система защиты компрессора от перегрузки
LG CH-05 Ошибка обмена данными между комнатным и наружным блоками сплит системы
LG CH-06 Ток потребления одного или нескольких исполнительных устройств наружного блока – реле, кратковременно был выше нормы
LG CH-07 Ток потребления всего наружного блока длительное время был выше нормы
LG CH-08 Неисправность двигателя вентилятора
LG CH-09 Неисправность 4 – ходового клапана
LG CH-10 Неисправен терморезистор контроля температуры корпуса компрессора сплит системы (обрыв или короткое замыкание)
Коды ошибок инверторных кондиционеров LG
Код ошибки = 21
Содержание = IPM неисправностей lg (компрессор от перегрузки по току)
LED01G (красный) = 2 раза
LED02G (зеленый) = 1 раз
Случай- ошибка = компрессора неисправности, IPM неисправностей
Код ошибки = 22
Содержание КТ = 2 (макс. ток)
LED01G (красный) = 2 раза
LED02G (зеленый) = 2 раза
Случай ошибки LG, — Ток 14А
Код ошибки = 23
Содержание LG, — DC Ссылка Низкий Volt
LED01G (красный) = 2 раза
LED02G (зеленый) = 3 раза
Случай ошибки = Напряжение цепи постоянного тока является 140V
Код ошибки = 24
Содержание = LG, — Низкое / Высокое давление
Свето-диод красный — индикатор сплит-системы LG моргнул 2-а раза
Световой диод красный =4 раза
Неисправность, — Low / High Пресс коммутатор открытом цикле
Код ошибки = 25
Содержание LG, — AC Низкий / переменного тока, повышенное напряжение
Свето-диод красный — индикатор сплит-системы LG моргнул 2-а раза
Световой диод красный =5 раз
Неисправность, — Входное напряжение переменного тока -140В, 300В
Код ошибки lg = 26
Содержание = DC компрессор позиции
Свето-диод красный — индикатор сплит-системы LG моргнул 2-а раза
Световой диод красный =мигает 6-ть раз
Неполадка = Позиция обнаружения ошибок
Код ошибки = 27
Содержание = PSC Fault (реактор)
Свето-диод красный — индикатор сплит-системы LG моргнул 2-а раза
Световой диод красный =7 раз
Неисправность, — от перегрузки по току на «IGBT»
Код ошибки = 28
Содержание = DC Ссылка Высокая Вольт
Свето-диод красный — индикатор сплит-системы LG моргнул 2-а раза
Световой диод красный =8 раз
Неполадка = Напряжение цепи постоянного тока является 420V
Код ошибки = 32
Содержание = выпускной трубы Temp. Высокий (инв. Compressor)
Свето-диод красный — 3 раза
Световой диод красный = индикатор сплит-системы LG внутр. блока кондиционера моргнул 2-а раза
Неисправность, — Сброс датчика Высокая температура. (105°C)
Код ошибки = 33
Содержание = выпускной трубы Temp. Высокий (Cons. Compressor)
Свето-диод красный — 3 раза
Световой диод красный =3 раза
Неисправность, — Сброс датчика Высокая температура. (105°C)
Код ошибки = 40
Содержание = CT цепи
Свето-диод красный — 4 раза
LED02G (зеленый) =
Неисправность, — КТ Неисправность цепи Off
Код ошибки = 41
Содержание = D-Pipe датчика INV. Компрессор (Open / Short)
Свето-диод красный — 4 раза
Световой диод красный =1 раз
Неисправность, — Открыть / короткого замыкания
Код ошибки = 44
Содержание = датчик воздуха (открыть / Короткие
Свето-диод красный — 4 раза
Световой диод красный =4 раза
Неисправность, — Открыть / короткого замыкания
Код ошибки = 45
Содержание = дир. Труба Sensor (Open / Short)
Свето-диод красный — 4 раза
Световой диод красный =5 раз
Неисправность, — Открыть / короткого замыкания
Код ошибки = 46
Содержание = Всасывающая труба Sensor (Open / Short)
Свето-диод красный — 4 раза
Световой диод красный =мигает 6-ть раз
Неисправность, — Открыть / короткого замыкания
Код ошибки = 47
Содержание = D-Pipe Минусы Sensor. Компрессор (Open / Short)
Свето-диод красный — 4 раза
Световой диод красный =7 раз
Неисправность, — Открыть / короткого замыкания
Код ошибки = 48
Содержание = D-Pipe & датчик воздуха (открытый)
Свето-диод красный — 4 раза
Световой диод красный =8 раз
Неисправность, — Двойной датчик отключен. Разомкнуто соединение датчика температуры нагнетания компрессора и датчик температуры воздуха в Наружном блоке. Необходимо проверить датчики и их подключение, соединительные провода либо плату управления.
Код ошибки = 51
Содержание = За Емкость
Свето-диод красный — 5 раз
Световой диод красный =1 раз
Неисправность, — За Емкость Комбинация
Код ошибки = 53
Содержание = Ошибка связи (Крытый Открытый)
Свето-диод красный — 5 раз
Световой диод красный =3 раза
Неполадка = Плохо / Потеря связи
Код ошибки = 60
Содержание = EEPROM контрольной суммы
Свето-диод красный — мигает 6-ть раз
LED02G (зеленый) =
Неисправность, — Контрольная сумма Mis-Match
Код ошибки = 61
Содержание = дир. Труба датчика температуры
Свето-диод красный — мигает 6-ть раз
Световой диод красный =1 раз
Неполадка = Конд. Температура Высокий (65°C)
Код ошибки = 62
Содержание = радиатора датчик температуры
Свето-диод красный — мигает 6-ть раз
Световой диод красный = индикатор сплит-системы LG внутр. блока кондиционера моргнул 2-а раза
Неисправность, — радиатора Temp. Высокий (85°C)
Код ошибки = 65
Содержание = радиатора Sensor (Open / Short)
Свето-диод красный — мигает 6-ть раз
Световой диод красный =5 раз
Неисправность — Открыть / короткого замыкания
Неполадка = Напряжение цепи постоянного тока является 420V
Коды ошибок промышленных кондиционеров LG
Внутренний блок:
01 — датчик температуры воздуха короткозамкнут или обрыв в цепи;
02 — датчик температуры испарителя короткозамкнут или обрыв в цепи;
03 — плохое соединение внутреннего блока с проводным пультом управления;
04 — ошибка дренажного насоса (помпы) или поплавкового датчика уровня конденсата;
05 — ошибка в межблочном соединении внешнего и внутреннего блоков;
06 — датчик температуры наружного блока короткозамкнут или обрыв в цепи;
07 — внутренние блоки мультисистемы включены на разные режимы работы;
HL — та же ошибка, что и 04, поплавковый датчик разомкнут;
CL — установлен детский замок, для включения нажмите Timer & Min Buttons 3 секунды;
Po — установлен режим jet cool, для выхода нажмите кнопку jet cool
Внешний блок:
21 — перегрузка компрессора по току;
22 — ток компрессора более 14 А;
23 — напряжение постоянного тока ниже 140 В; (не напряжение питания, а после модуля преобразования)
24 — ошибка по высокому/низкому давлению, датчики давления разомкнуты;
25 — напряжение питания выше/ниже нормального значения;
26 — DC Compressor Position;
27 — ошибка PSC (реактор, катушка индуктивности);
28 — DC Link High Volts;
32 — Высокая температура нагнетательной трубы (INV);
33 — Высокая температура нагнетательной трубы (Cons.);
40 — короткое замыкание CT;
41 — датчик температуры D-Pipe замкнут/оборван (INV);
44 — датчик температуры наружного воздуха замкнут/оборван;
45 — датчик температуры конденсатора замкнут/оборван;
46 — датчик на всасывающей трубке замкнут/оборван;
47 — D-pipe датчик замкнут/оборван;
48 — D-pipe датчик и датчик температуры воздуха отсутствуют/оборваны;
51 — комбинированная перегрузка по мощности;
52 — ошибка соединения (main micom-sub micom);
53 — ошибка соединения (внутренний-наружный блоки);
54 — для систем с 3-х фазным питанием, неправильная последовательность фаз,поменять фазу;
60 -ошибка EEPROM (внутренняя энергонезависимая память)
61 -высокая температура трубки конденсатора (конденсера)
62 -высокая температура радиатора(скорее всего имеется в виду радиатор охлаждения силового модуля инвертора)
63 -низкая температура конденсатора
65 -датчик температуры радиатора замкнут/оборван
67 -заблокирован наружный BLDC (безколлекторный электродвигатель постоянного тока) вентилятор
105 -нет связи между главной платой управления и платой управления вентилятором
Заявка на ремонт кондиционера
Какая ошибка у вашего кондиционера?
Код ошибки: CH-01
Датчик температуры воздуха в помещении неисправен
Короткое замыкание в цепи датчика, обрыв цепи датчика. Попадание влаги в датчик, Неисправен контакт в разъеме, Вышла из строя плата управления
Код ошибки: CH-02
Датчик температуры хладагента, который находится при входе в теплообменник, неисправен
Короткое замыкание в цепи датчика, обрыв цепи датчика. Попадание влаги в датчик, Неисправен контакт в разъёме, Вышла из строя плата управления
Код ошибки: CH-03
Нет соединение с проводным пультом
Плохой контакт на плату управления в пульте управления, окисление контактов, перестал функционировать пульт управления, не работает плата управления ( то есть компоненты, отвечающие за соединение с пультом управления)
Проверьте провода пульта управления на наличие повреждений. — Проверьте состояние контактов в разъёме подключения соединительного провода на плате и на ПУ — Необходимо прозвонить соединительный провод — Убедиться что пульт управления исправен и работоспособен — Убедиться что плата управления цела.
Код ошибки: CH-04
Не работает дренажный насос
Дренажный шланг может быть забит, двигатель насоса неисправен, цепь поплавкового датчика разомкнута
Проверить двигатель дренажного насоса на исправность, оценить состояние дренажного шланга, проверить правильность установки дренажного насоса
Решение не помогло или нужно больше информации?
Проконсультируйтесь со специалистом или вызовите мастера!
Код ошибки: CH-05
В связи между внутренним и наружным блоком присутствует ошибка
Отсутствует питание на внутреннем или наружном блоке, ошибка подключения кабеля питания. Мотор вентилятора вышел из строя. Ошибка связи из-за внешних помех, если рядом пролегает электрический кабель.
Прежде всего проверить подключения кабеля, проверить наличие напряжения на плате управления блоков. Проверить исправность двигателя вентилятора.
Код ошибки: CH-06
Датчик, который расположен на выходе из теплообменника внутреннего блока, неисправен
Короткое замыкание в цепи датчика, обрыв цепи датчика. Попадание влаги в датчик, Неисправен контакт в разъёме, Вышла из строя плата управления
Код ошибки: CH-07
Ошибка EEPROM (ПЗУ)
Неисправен контакт ПЗУ на плате управления
Необходимо проверить контакт и правильность установки чипа ПЗУ
Код ошибки: CH-10
Неисправность БДПТ электродвигателя вентилятора внутреннего блока
Остановка вентилятора из-за внешнего воздействия — Плохой контакт в разъёме на плате управления — Неисправность двигателя — Плата неисправна
Устраните внешние воздействия — Проверьте контакт разъёма — Проверьте двигатель вентилятора — Проверьте плату управления
Код ошибки: CH-12
Датчик, который находится в центральной части теплообменника внутреннего блока, неисправен
Короткое замыкание в цепи датчика, обрыв цепи датчика. Попадание влаги в датчик, Неисправен контакт в разъёме, Вышла из строя плата управления
Код ошибки: СН21
Повышенный потребляемый ток компрессора с инверторным приводом
— Утечка хладагента — Компрессор заклинен — Плата инвертора неисправна
— Проверьте контур на возможность утечки хладагента — Проверить на неисправность силовые элементы платы управления компрессором — Проверить цепь электродвигателя компрессора на предмет обрывов и короткого замыкания
Код ошибки: СН22
Перегрузка. Повышенный потребляемый ток наружного блока
Загрязненный теплообменник наружного блока, низкая циркуляция охлаждающего воздуха в месте установки наружного блока (есть помехи для теплообмена, вентилятор загражден). Также причиной может являться низкое напряжение у источника питания
— Проверить напряжение источника питания — Проверить циркуляцию охлаждающего воздуха в месте, где установлен наружный блок (проверить, чтобы блоку ничего не мешало проводить теплообмен). — Прочистить фильтр внутреннего блока и теплообменник наружного блока
Код ошибки: СН23
Слишком низкое или высокое напряжение сети
Плата управления компрессором неисправна, низкое напряжение у источника питания, Плохо закреплен провод
Проверить качество подключения к источнику питания. Проверить подключения проводов реактора. Проверить датчик напряжение на исправность
Код ошибки: СН26
При запуске компрессора возникает неисправность
Компрессор вышел из строя, плата управления компрессором неисправна, На разъеме компрессора присутствует дефект провода
— Проверить провода компрессора на наличие дефектов — Проверить плату управления компрессора на работоспособность
Код ошибки: СН27
Перегрузка тока в цепи конвектора (преобразователя тока AC –DC)
— Работа кондиционера на перегрузках, недостаточная циркуляция воздуха в местах крепления внешнего блока кондиционера — Повреждение элементов выпрямителя PSC в плате управления — Неверные характеристики реактора
— Проверить циркуляцию воздуха в районе наружного блока — Проверить характеристики реактора
Код ошибки: СН32
Температура выше нормы нагнетания компрессора
-Датчик, который отвечает за измерение температуры нагнетания, неисправен — Утечка или недостаточное количество хладагента — Плохие контакты разъемов
-Проверить в местах крепления наружного блока хорошую циркуляцию воздуха — Поверить количество хладагента в системе, исключить утечку — Проверить датчик температуры нагнетания на исправность, проверить подключения разъемов к плате управления
Код ошибки: СН34
Высокое давление хладагента в системе
Циркуляция воздуха через теплообменник затруднена (фильтр внутреннего блока загрязнен, в случае работы в режиме охлаждения или обмерзший теплообменник наружного блока в случае работы в режиме обогрева) — Количество хладагента в системе меньше допустимой нормы — Проблемы с платой управления — Разъемы неисправны
Проверить в местах крепления наружного блока хорошую циркуляцию воздуха — Поверить количество хладагента в системе, исключить утечку — Проверить датчик температуры нагнетания на исправность — Проверить подключения разъемов к плату управления — Прочистить фильтры при условии их загрязнения
Код ошибки: CH35
Низкое давление хладагента в системе
— Циркуляция воздуха через теплообменник затруднена (фильтр внутреннего блока загрязнен, в случае работы в режиме охлаждения или обмерзший теплообменник наружного блока в случае работы в режиме обогрева) — Количество хладагента в системе меньше допустимой нормы — Проблемы с платой управления — Разъемы неисправны
— Проверить в местах крепления наружного блока хорошую циркуляцию воздуха — Поверить количество хладагента в системе, исключить утечку — Проверить датчик температуры нагнетания на исправность — Проверить подключения разъемов к плату управления — Прочистить фильтры при условии их загрязнения
Код ошибки: СН41
Датчик температуры нагнетания инверторного компрессора неисправен
— В цепи датчика случился обрыв или короткое замыкание — Отходит контакт в разъеме на блоке управления — Неисправность платы управления
— Проверить разъемы датчиков — Проверить сопротивление датчика: — СН41 — 200 кОм при 25°C (при отключенном датчике) — СН44 -10 кОм при 25°C (при отключенном от платы датчике) — СН45/48 — 5 кОм при 25°C (при отключенном от платы датчике) — СН46 — 5 кОм при 25°C (при отключенном от платы датчике)
Код ошибки: СН44
Неисправность датчика температуры уличного воздуха
— В цепи датчика случился обрыв или короткое замыкание — Отходит контакт в разъеме на блоке управления — Неисправность платы управления
— Проверить разъемы датчиков — Проверить сопротивление датчика: — СН41 — 200 кОм при 25°C (при отключенном датчике) — СН44 -10 кОм при 25°C (при отключенном от платы датчике) — СН45/48 — 5 кОм при 25°C (при отключенном от платы датчике) — СН46 — 5 кОм при 25°C (при отключенном от платы датчике)
Код ошибки: СН45/48
Неисправность или ошибка датчика температуры трубки теплообменника наружного блока кондиционера
— В цепи датчика случился обрыв или короткое замыкание — Отходит контакт в разъеме на блоке управления — Неисправность платы управления
— Проверить разъемы датчиков — Проверить сопротивление датчика: — СН41 — 200 кОм при 25°C (при отключенном датчике) — СН44 -10 кОм при 25°C (при отключенном от платы датчике) — СН45/48 — 5 кОм при 25°C (при отключенном от платы датчике) — СН46 — 5 кОм при 25°C (при отключенном от платы датчике)
Код ошибки: СН46
Ошибка датчика температуры на линии всасывания компрессора
— В цепи датчика случился обрыв или короткое замыкание — Отходит контакт в разъеме на блоке управления — Неисправность платы управления
— Проверить разъемы датчиков — Проверить сопротивление датчика: — СН41 — 200 кОм при 25°C (при отключенном датчике) — СН44 -10 кОм при 25°C (при отключенном от платы датчике) — СН45/48 — 5 кОм при 25°C (при отключенном от платы датчике) — СН46 — 5 кОм при 25°C (при отключенном от платы датчике)
Код ошибки: СН61
Температура конденсации превышает норму
Работа наружного блока в недостаточной циркуляции воздуха, что способствует перегрузкам. Теплообменник загрязнен. Неисправность датчика температуры конденсации
Проверить и обеспечить нормальную циркуляцию воздуха в местах крепления наружного блока кондиционера. Проверить не перезаправлена ли система фреоном. Проверить корректность установки термодатчика
Код ошибки: СН62
Перегрев радиатора силового транзистора на плате управления компрессором
— Вентилятор наружного блока кондиционера заклинил — Неправильное место установки наружного блока — Неисправность контура — Неисправность датчика температуры
— Проверьте состояние вентилятора наружного блока — Проверьте место установки наружного блока — Проверьте разъём соединения датчика — Проверьте контур датчика на плате управления компрессором
Код ошибки: СН67
Неисправность электродвигателя вентилятора наружного блока
— Вентилятор заклинил по механическим причинам — Электродвигатель вентилятора вышел из строя
— Проверить есть ли помеха работе вентилятора внешними предметами — Оценить работоспособность двигателя вентилятора — Проверьте плату управления (элементы контура управления вентилятором)
Код ошибки: СН72
Неисправность при переключении 4-х ходового клапана
— Разомкнут разъём подключения на плате — Привод 4-х ходового разомкнут, либо замкнут — Проблема платы управления
— Проверьте функциональность подключения на плате управления — Проверьте сопротивление катушки привода — Проверьте напряжение на плате управления