Cl plus key fail philips как исправить

Помогло меню, 1,9,9,9, как написано выше. В мастерской просили за ремонт 5000 рублей года три назад.  зэзюща  8 января 

На телевизоре Philips 40 PFT 4100/60 появился красный прямоугольник с надписью: «CI plus key fail». Способ как на видео с переключением 65 пункта меню не работает так как у меня нет пункта drm warning, там чтото типа «LVCD тратата «  фищопы  3 октября 2022 

Меню, 1,9,9,9, назад. Попадаем в спец. меню. Там выбираем virgin mode on. Телек перезагружается, со сбросом всех настроек и каналов. Мне помогло — табличка исчезла.  щетенал  12 ноября 2021 

Появилась после аварийного отключения эл-ва. Обновил ПО, все прошло.  гивефуря  6 мая 2021 

Проблема такая: На PHILIPS 32PHT4100/60 на экране выскочила красная табличка с надписью: Cl Plus key Fail как избавится от этой проблемы?  Аlex8121  4 мая 2021 

Дти нажимали кнопки пульта и в каком-то меню включили режим автонастройки цвета после чего тв не реагирует на кнопки пульта, на экране меняются разноцветные экраны белый, красный, зеленый, синий, черный и так по кругу  игяжилад  11 января 2017 

ТВ Philips 40pft4100/60 вышла красная надпись на верхней части экрана»cl plus key fail», как избавиться?  IlnurJan  11 июля 2016 

Cl plus key fail на филипке , че за хрень?!  оцахю  26 января 2016 

В телевизорах этой линейки, собранных на шасси TPN15.1ELA часто случается сбой прошивки флэш-памяти. Проявляться такая неисправность может по-разному: телевизор может просто не включаться, а может как в данном случае, «вывесить красный флаг».

На фото видно красный прямоугольник с пугающей надписью «CI Plus Key Fail».
Казалось бы, нужно залить исправную прошивку и проблема решена. Этот метод работает с телевизорами многих производителей, но только не с Philips. Здесь прошивка привязана к «железу» и с «не родной» прошивкой телевизор просто не запустится. Производитель рекомендует в таком случае менять основную плату, которая стоит дорого. 
Тем не менее мы научились решать и такую проблему: из неисправной флэш-памяти считывается прошивка, режется на куски, далее прошивка собирается из множества фрагментов, затертые фрагменты заменяются исправными, считанными с рабочего телевизора. После чего собранная прошивка заливается в новую микросхему флэш-памяти. 
Результат на фото — телевизор снова исправно работает.

oot-
DRAM Channel A Calibration.
Byte 0 : DQS(11 ~ 37), Size 27, Set 22.
Byte 1 : DQS(3 ~ 34), Size 32, Set 16.
Byte 2 : DQS(3 ~ 34), Size 32, Set 16.
Byte 3 : DQS(-1 ~ 29), Size 31, Set 12.
DRAM A Size = 256 Mbytes.
oot
Start Pmain
0x00004000
NID=0x9500f1ec
LZHS addr:0x00100040
LZHS size:0x00096140
LZHS checksum:0x0000000b
oot
Start Lmain

MT5365 Boot Loader v0.9
[PCMCIA]Set PCMCIA Access IF : SPI
SPIHW_Init —— Set SPI PinMux
SPI dummy delay:0x10
External CI Version : MT5135
Output clock from main chip.
PCMCIA Reset Demod GPIO=35, 0->1
SPI_SetPll(), spi clock: 27 Mhz
External IC Initilization done
MUSB none SoftReset 0x29424 = 0x01030000.
MUSB pBase = 0xF0029000 init ok.
MUSB none SoftReset 0x29424 = 0x01030000.
MUSB pBase = 0xF002E000 init ok.
Boot reason: A/C power on!!————-use external edid, disable internal edid
——————
SIF_Master0: new design
SIF_Master1: old design
Boot reason: A/C power on!!T8032 init A/C on case loader stage…
Load T8032 FW (addr: 0x 2d3827c, size: 24576)success!!
T8032 FW version: 18
T8032 change to loader stage…
LDR_FlashCopy 0xf010 0x34d80 0x80
Switch NAND pinmux
Detect NAND flash ID: 0x9500F1EC
Detect SS K9F1G08U0B/C NAND flash(SLC): 128MB
NAND_BDM_Mount: Partid=0, offset=0x0, size=0x40000
[BDM] Partition: 0, Bad Block Count: 0

Do USB upgrade

No USB device.
USB upgrade stop
Boot reason: A/C power on!!Boot reason: A/C power on!![PDWNC]PDWNC_TPV_Determine
NextState : u4Event = 0x6
PDWNC_TPV_DetermineNextState : u4Current = 1
PDWNC_TPV_DetermineNextState : system booting
[PDWNC] Virgin Mode Status : 0x0, Offset :0x38
PDWNC_TPV_DetermineNextState : event = PDWNC_POWER_DOWN_AC_POWER
Current = 0x1, Event = 0x6, Next = 0x1
Wakeup keypad array = 1
Boot reason: A/C power on!![PDWNC]PDWNC_ReadWakeupReason = 0x6
[PDWNC]Enter normal mode, LED changes to normal
PDWNC_TPV_EnterNextState : u4Next = 0x1
Boot reason: A/C power on!!
A_Mute GPIO=11 release
AMP mute GPIO=cb release
Reset Demod GPIO=23, 0->1
Display 0x02d9ec4c background:0x00000000
2 bytes panel index is : 142 (0x 8e)
Find panel index 142 from EEPROM
[LVDS] DVOPLL init control word only
[LVDS] VOPLL Initialize successful !
LODFP.
Boot reason: A/C power on!!———- Panel[142] PANEL_SHARP_LK400D3LB83F 1920×1
080 ———-
PixelClk[Max=152000000, 60Hz=148351648, 50Hz=123750000, Min=120000000]
HTotal[Max=2599, 60Hz=2199, 50Hz=2199, Min=2099] HSyncLen[60Hz=279, 50Hz=279]
VTotal[Max=1399, 60Hz=1124, 50Hz=1124, Min=1108] VClk[Max=63, Min=47]
HSyncWidth=24, VSyncWidth=0, HPosition60Hz=0x800, HPosition50Hz=0x800, VPosition
=1024
LVDS_NS, LVDS_ODD_SW_OFF, DUAL_PORT, DISP_30BIT, WFB_PANEL_RESET_OFF, PWM_LOW_PA
NEL_BRIGHT
3D_POLARIZED
Backlight[High=0x0, Middle=0x70, Low=0xe0]
DimFreq60Hz=150, DimFreq50Hz=150
Delay[LvdsOn=30, BacklightOn=1500, BacklightOff=350, LvdsOff=200]
MaxOverscan=30

Current panel setting is PANEL_SHARP_LK400D3LB83F
Backlight gpio=25, turn on value=0, LVDS gpio=16, turn on value=1
Pixel Shift=0 (1920 x 1080)
LDR_OsdDisplay(13, 0x02d42560, 400, 100)
Color:13 BmpAddr:0x02d42560 Width:400 Height:100
OSD_SetTVEOut: 1
Panel 1920 x 1080

NAND load lzhs header from SysImgA(part:1) to dram(0x2fe6a00), size=2048
NAND_BDM_Mount: Partid=1, offset=0x40000, size=0x1e00000
[BDM] Partition: 1, Bad Block Count: 0
Decompression image to 0x00010000…

NAND load image from SysImgA(part:1) to dram(0x2fe6a00), size=0xdf6d55
secure boot ok
LZHS hardware decode start
LZHS hardware decode done
Starting image…

Booting
Nucleus Heap is at 0x012e96e8(0x0ad0bf80)
Main task stack is at 0x012e96f8 (0x00002000)

============================================
Dram Size: 0x10000000
Memory for Image at 0x00010000(0x012d3ee8):
Memory Reserved for MMU at 0x006f4000(0x00004000)
Memory for OSAI at 0x012eb708(0x0ad09678)
Memory Reserved for ARM lib at 0x0bff96f8(0x00002908)
Memory Reserved for FBM at 0x0bffc000(0x04004000)
drv_init as EU model
Preloader T8032 ack !
SIF_Master0: new design
SIF_Master1: old design
[PCMCIA]Set PCMCIA Access IF : SPI
[PCMCIA]External CI Version : MT5135
[PCMCIA]External IC Initilization done
_u1PanelIndex 142
[CEC]EEPROM ok. u4Val = 1.
[SHARP_PANEL_______———————————TMDS361 init—————-
———————
TMDS361 is GPIO mode
______________HDMI fast booting init…
_________________]
2 bytes panel index is : 142 (0x 8e)
Find panel index 142 from EEPROM
TunerInit…………………EEPROM(tuner): Ofst0=0x21b,Ofst1=0xbcb,Ofst2=0x112
b,def=0x69
[MUSB]USB0: Set GPIO23 = 0.
[MUSB]USB1: No define vbus gpio.
[MUSB]ucos MUSB SoftReset 0xF0029024 = 0x01C30000.
[MUSB]ucos MUSB SoftReset 0xF002E024 = 0x01C30000.
Read TunerType from EEPROM: addr(0x21b)=0xa1,addr(0xbcb)=0xa1,addr(0x112b)=0xa1
Tuner 1 LTDIS_GetOpenFct Pair 0 done!
[[MUSB]Set port-0 to Host mode.
PCMCIA]External PCMCIA Interrupt Mode.
[PCMCIA]MT5135 Driving Setting 8mA
[PCMCIA]CI 5V Power Off
ofst0=0x21b, ofst1=0xbcb, ofst2=0x112b,[MUSB]Set port-1 to Host mode.
def=0x69
read TunerType from EEPROM, addr0x21b=0xa1, addr0xbcb=0xa1, addr0x112b=0xa1
Find corresponding tuner for registration. (total 2 t[MUSB]Set port-0 to Host mo
de.
uners in pool)(TunerType=0xA1)
Register DVBT Tunerall type = 161
Tuner ENV57U03D5F init done!
[MUSB]Set port-1 to Host mode.
[NPTV]Display Init[NPTV]Video SW InitZero TDC memory address

Scene ID, APL, Noise Value,Bin0,Bin1,Bin2,Bin3,Bin4,Bin5,Bin6,Bin7,Bin8,Bin9,Bin
10,Bin11,Bin12,Bin13,Bin14,Bin15,DS0,DS1,DS2,DS3,DS4,DS5,DS6,DS7,DS8,DS9,DS10,DS
11,DS12,DS13,DS14,DS15,MoPxlRatio,MinDS,MaxDS,DSRatio,AvgDS,Noise Level,Final Co
nfidence,MoPxl Confidence,DSRatio Confidence,
[NPTV]OD use external error handling
[NPTV]Load OD table
[NPTV]Load OD table
[NPTV]Load FB table
[NPTV]NOT Support OD
[NPTV]vApiVideoInit
[NAND]NAND_BDM_Mount: Partid=0, offset=0x0, size=0x40000
[NAND][BDM] Partition: 0, Bad Block Count: 0
[NAND]NAND_BDM_Mount: Partid=1, offset=0x40000, size=0x1e00000
[NAND][BDM] Partition: 1, Bad Block Count: 0
[NAND]NAND_BDM_Mount: Partid=3, offset=0x1e40000, size=0x1e00000
[NAND][BDM] Partition: 3, Bad Block Count: 2
[NAND]NAND_SDM_Mount: Partid=5, offset=0x3c40000, size=0x43c0000
[NAND][SDM] Partition: 5, Bad Block Count: 0
[NPTV]FlashPQ ID OK
[NPTV]Restore Flash SmartPic Successful
[NPTV]GAMMA SCRIPT=SHARP_LK400D3LB83F
[NPTV]Load OD table
[NPTV]Load OD table
[NPTV]Video HW Init[NPTV]VBI_Inithdmi re-init
[MUSB]Set port-0 to Host mode.
[MUSB]Set port-1 to Host mode.

TVD MsgCtrl: NRL:60/40, PER:100/90
_bHDMIState change from HDMI_STATE_NOTREADY to HDMI_STATE_INIT
_bHDMIState change from HDMI_STATE_INIT to HDMI_STATE_PWON
[NPTV]Verf PE Table Passed
DVBT_Initialize OK!
[NPTV]FlashPQ ID OK
[NPTV]QTY SCRIPT=SHARP_LK400D3LB83F
[NPTV]QTY ID OK
[NPTV]Restore FlashPQ Qty successfully
[NPTV]Enable AdaptiveLuma
_bHDMIState change from HDMI_STATE_PWON to HDMI_STATE_PWON2
ofst0=0x21b, ofst1=0xbcb, ofst2=0x112b, def=0x69
read TunerType from EEPROM, addr0x21b=0xa1, addr0xbcb=0xa1, addr0x112b=0xa1
Find corresponding tuner for registration. (to_bHDMIState change from HDMI_STATE
_PWON2 to HDMI_STATE_SCDT
tal 2 tuners in pool)(TunerType=0xA1)
Register DVBC Tunerall type = 161
Tuner ENV57U03D5F init done!
DVBC_Initialize OK!
Tuner 0 LTDIS_GetOpenFct Pair 1 done!
ofst0=0x21b, ofst1=0xbcb, ofst2=0x112b, def=0x69
read TunerType from EEPROM, addr0x21b=0xa1, addr0xbcb=0xa1, addr0x112b=0xa1
Find corresponding tuner for registration. (total 2 tuners in pool)(TunerType=0x
A1)
Register ATD Tunerall type = 161
Tuner ENV57U03D5F init done!
ATD_Initialize successful !
Read NAND Flash AQ Comm Data Success!
load cdnotch code sz 80 offset 143130 0xFA7A600
load cdnotch code sz 80 offset 143130 0xFA7A600
load cdnotch code sz 80 offset 143130 0xFA7A600

Image ROBase:0x00010af0 ROLimit:0x006f8480
Protect readonly by region 1: from 0x00000000 ~ 0x00000040.
MMU protect: 0x00010af0 ~ 0x006f7ffc
Successed to initialize Memory Intrusion Detection!

DTV>Driver Logo Disabled!
OSD_SetTVEOut: 1
total: 5612, avail: 3450, free: 3450
[FM](/dev/flash_sunrise_0) is mounted to (/mnt/sunr) successfully(0)
total: 9188, avail: 8282, free: 8282
[FM](/dev/nand_21_0) is mounted to (/mnt/demo) successfully(0)
total: 1014, avail: 802, free: 802
[FM](/dev/flash_fs_tp_0) is mounted to (/mnt/aud) successfully(0)
{CI_glue}:ci_eng_init
{CI_glue}- expect PROD key
{CI}CI_RegInterrupt_nfy
HMAC-SHA1 verify failed
{CI_glue}- c[0]
{DT} Real Time Clock is available on this system.
reason: 0x00000006 — 0x00000000
<AM> wakeup reason = 6
[ACFG_CUSTOM] acfg_custom_get_svl_tsl_dual_bank ui1_g_svl_tsl_dual_bank == DUAL_
BANK_SVL_TSL_INVALID and get form plf is 1
[ACFG_CUSTOM] acfg_custom_get_svl_tsl_dual_bank: MAIN
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
[ACFG_CUSTOM] acfg_custom_get_svl_tsl_dual_bank: MAIN
<PLF_OPT> Align option codes (OPC_USED[NVM] — OPC1 OPC2 OPC3)
12 — 0 0 0
4 — 0 0 0
208 — 0 0 0
2 — 0 0 0
184 — 0 0 0
32 — 0 0 0
7 — 0 0 0
30 — 0 0 0
56 — 56 56 56
23 — 0 0 0
0 — 0 0 0
106 — 0 0 0
64 — 0 0 0
0 — 9 9 9
0 — 142 142 142
122 — 0 0 0
[ACFG_CUSTOM] acfg_custom_get_svl_tsl_dual_bank: MAIN
[ACFG_CUSTOM] acfg_custom_get_svl_tsl_dual_bank: MAIN
[a_cfg_custom_bds_update_mutirc_state] state = 0
IRRX_FilterSystemCode: set postive system code…
(0)nd system code: 0
(1)nd system code: 3
(2)nd system code: 7
Pass data0 to T8032 0x0
Pass data0 to T8032 0x3
[ACFG_CUSTOM] acfg_custom_get_svl_tsl_dual_bank: MAIN
[ACFG_CUSTOM] acfg_custom_get_svl_tsl_dual_bank: MAIN
[BGM] a_bgm_init.
FS(0x4004500) B3 = 0x4, B2 = 0x0, B1 = 0x45, B0 = 0x0
FS(0x4004500) B3 = 0x4, B2 = 0x0, B1 = 0x45, B0 = 0x0
[TCL-100426-02 i2_blue_mute = 0]
FS(0x4004500) B3 = 0x4, B2 = 0x0, B1 = 0x45, B0 = 0x0
Zero TDC memory address
Zero TDC memory address
BGM: Power mgmt init
BGM: Update scan init
[BGM_OAD_DTC] _oad_detect_init
[BGM_OAD_DLD] _oad_download_init
BGM: Ambilight module init
[BGM:] _bgm_am_power_on_evt_cb_fct
reason: 0x00000006 — 0x00000000
[BGM]: Pass to continue power on
[ACFG_CUSTOM] acfg_custom_get_svl_tsl_dual_bank: MAIN
[ACFG_CUSTOM] acfg_custom_get_svl_tsl_dual_bank: MAIN
[TCL-100426-02 i2_blue_mute = 0]
FS(0x4004500) B3 = 0x4, B2 = 0x0, B1 = 0x45, B0 = 0x0
FS(0x0) B3 = 0x0, B2 = 0x0, B1 = 0x0, B0 = 0x0
TunerNimTest(TunerId=1) ok(return=0)

S/W Version

TPM62E 2.26

NVM Version

1.03

[ACFG_CUSTOM] acfg_custom_get_svl_tsl_dual_bank: MAIN
{CDB} Loading metadata (version 7)
{CDB} Loading metadata (version 7)
===255
===267
[ACFG_CUSTOM] acfg_custom_get_svl_tsl_dual_bank: MAIN
[ACFG_CUSTOM] acfg_custom_get_svl_tsl_dual_bank: MAIN
[CEC]CEC Driver ON
————vHdmiSetARCOnOff(0)—————
——ARC off, GPIO 707 set to 1——
[AUTO_LIP_SYNC WARNING] Register the auto lip sync.
[AUTO_SUBTITLE_SHIFT WARNING] register auto subtitle shift.
{CDB} Loading metadata (version 7)
vc_cre init
vc_hiden init
{CDB} Loading metadata (version 7)
reason: 0x00000006 — 0x00000000
_nav_ci_info_init() call x_ci_reg_nfy()…………………
FS(0x0) B3 = 0x0, B2 = 0x0, B1 = 0x0, B0 = 0x0
[ OAD_ACFG] a_cfg_get_oad_reminder, 0
[ OAD_ACFG] a_cfg_set_oad_reminder, 0
<ACFG> Open audio outport: 110 ms
reason: 0x00000006 — 0x00000000
reason: 0x00000006 — 0x00000000

[!!!Return fail:nav_cec.c:nav_cec_is_amp_exist:2711:-13]
[a_cfg_custom_bds_update_mutirc_state] state = 0
IRRX_FilterSystemCode: set postive system code…
(0)nd system code: 0
(1)nd system code: 3
(2)nd system code: 7
Pass data0 to T8032 0x0
Pass data0 to T8032 0x3
reason: 0x00000006 — 0x00000000
[MISC] pcl wakeup reason: 6
[BGM_OAD_DTC] _oad_detect_handle_msg :13
[BGM_OAD_DLD] _oad_download_handle_msg, it will not process any message
HMAC-SHA1 verify failed
reason: 0x00000006 — 0x00000000
inpSrc[1]
FS(0x4004400) B3 = 0x4, B2 = 0x0, B1 = 0x44, B0 = 0x0
==333
{APP_TV} TV Brdcst type = 1 TV_SCART Enabled: 0 Monitor_SCART Enabled: 1
Disconnect FB at VFE disconnect
FS(0x4004500) B3 = 0x4, B2 = 0x0, B1 = 0x45, B0 = 0x0
[NPTV]AdaptiveLuma: Enable Luma Histogram
FS(0x4004500) B3 = 0x4, B2 = 0x0, B1 = 0x45, B0 = 0x0

[SYS] Version Begin ===================================================
[SYS] Serial Number: REL_20120809_183944
[SYS] Version End ===================================================

Watchdog enable:800001665
[ACFG_CUSTOM] acfg_custom_get_svl_tsl_dual_bank: MAIN
reason: 0x00000006 — 0x00000000
[ACFG_CUSTOM] acfg_custom_get_svl_tsl_dual_bank: MAIN
[ACFG_CUSTOM] acfg_custom_get_svl_tsl_dual_bank: MAIN
[ACFG_CUSTOM] acfg_custom_get_svl_tsl_dual_bank: MAIN
Config NR to Datamode(3)
[NPTV]SCE SCRIPT=SHARP_LK400D3LB83F
a_cfg_custom_is_Russia_model TRUE
Zero TDC memory address
Zero TDC memory address
{wzd} register dt notify callback
[PHM_UPG] _phm_upg_init_fct, 201012101907:TTTTTTTTTTTTTTTTTc_ci_get#CI_GET_TYPE_
SLOT_NUM
c_ci_get#CI_GET_TYPE_SLOT_INFO
e
FS(0x4004500) B3 = 0x4, B2 = 0x0, B1 = 0x45, B0 = 0x0
[AUD]#### Detect TV Sys = 13 #######
[MUSB]USB0: Set GPIO23 = 1.
[MUSB]USB1: No define vbus gpio.
FS(0x4004500) B3 = 0x4, B2 = 0x0, B1 = 0x45, B0 = 0x0
==333
FS(0x4004500) B3 = 0x4, B2 = 0x0, B1 = 0x45, B0 = 0x0
FS(0x4004500) B3 = 0x4, B2 = 0x0, B1 = 0x45, B0 = 0x0
FS(0x4004500) B3 = 0x4, B2 = 0x0, B1 = 0x45, B0 = 0x0

[nav_cec_auto_sbti_sh.c:nav_cec_auto_sbti_sh_acfg_update:680:scr mode = 1,scr mo
de is same.]
[AUTO_SUBTITLE_SHIFT WARNING] Auto subtitle shift isn’t selected

[nav_cec_auto_sbti_sh.c:_nav_cec_auto_sbti_sh_report_cur_viewport:402:src la = 0
.]

[<report current viewport>nav_cec_auto_sbti_sh.c:_nav_cec_auto_sbti_sh_report_cu
r_viewport:413:src la = 0:ret = 0.]
[AUTO_LIP_SYNC WARNING] Get One UX version fail -1

[nav_cec_auto_sbti_sh.c:nav_cec_auto_sbti_sh_acfg_update:680:scr mode = 1,scr mo
de is same.]
[AUTO_SUBTITLE_SHIFT WARNING] Auto subtitle shift isn’t selected

[<report current viewport>nav_cec_auto_sbti_sh.c:_nav_cec_auto_sbti_sh_report_cu
r_viewport:413:src la = 0:ret = 0.]
[AUTO_LIP_SYNC WARNING] Get One UX version fail -1

[nav_cec_auto_sbti_sh.c:nav_cec_auto_sbti_sh_acfg_update:680:scr mode = 1,scr mo
de is same.]
[AUTO_SUBTITLE_SHIFT WARNING] Auto subtitle shift isn’t selected

[<report current viewport>nav_cec_auto_sbti_sh.c:_nav_cec_auto_sbti_sh_report_cu
r_viewport:413:src la = 0:ret = 0.]
[AUTO_LIP_SYNC WARNING] Get One UX version fail -1

Skip to content

We use cookies on our website to give you the most relevant experience by remembering your preferences and repeat visits. By clicking “Accept”, you consent to the use of ALL the cookies.