Crane 167 ошибки

1670097

Models 167, 177, 168, 457, 458, 764, 765, 784, 787

Snack/Refreshment Center 2

Snack Center 4

Set-Up & Operators’ Guide

12955 Enterprise Way Bridgeton, Missouri 63044-1200

(314) 298-3500 / Service: (800) 628-8363 www.CraneMS.com

Snack / Refreshment Center Setup and Operator’s Guide

Table of Contents

Snack / Refreshment Center Setup and Operator’s Guide

Snack / Refreshment Center Setup and Operator’s Guide

Model 168 — Exterior View

(Models 167, 457, 458, 764, 765 have similar appearance)

Snack / Refreshment Center Setup and Operator’s Guide

Model 168 — Interior View

(Model 167 has similar appearance)

Snack / Refreshment Center Setup and Operator’s Guide

Model 797 — Interior View

Snack / Refreshment Center Setup and Operator’s Guide

Preliminary

Power Requirements

The merchandiser is supplied with a service cord for the country of use and is terminated in a grounding type plug. The wall receptacle used for this merchandiser must be properly polarized, grounded, and of the correct voltage. Operating the merchandiser from a source of low voltage will VOID YOUR WARRANTY. Each merchandiser should have its own electrical circuit and that circuit should be protected with a circuit breaker or fuse conforming to local regulations.

1.Voltage Check — Place the leads of a voltmeter across the LINE (LIVE) and NEUTRAL terminals of the wall receptacle. The voltmeter should indicate 110-130 volts ac for 120 volt, 60 Hz locations, or 220240 volts ac for 230 volt, 50 Hz locations.

2.Polarity Check — Place the leads of a voltmeter across the LINE (LIVE) and GROUND terminals of the wall receptacle. The voltmeter should indicate 110-130 volts ac for 120 volt, 60 Hz locations, or 220240 volts ac for 230 volt, 50 Hz locations.

3.Noise Potential Check — Place the test leads of a voltmeter across the NEUTRAL and GROUND terminals of the wall receptacle. The meter should indicate 0 volts ac. A measurement greater than 1.5 — 2.0 volts ac could result in problems for the merchandiser’s electronic

circuitry caused by electrical noise.

Any deviation from these requirements could result in unreliable performance from your merchandiser.

Unpack the Machine

Remove all packing materials from the interior of the machine. Keep all documents; warranty cards, etc. Set aside the base plate kit (if present).

Snack / Refreshment Center Setup and Operator’s Guide

Controls and Indicators

INTERLOCK SWITCH. When the cabinet door is open, this switch turns off the glass heater, optional fan (if so equipped) and turns on the service light (not present on all models).

LOW VOLTAGE SWITCH. Informs the controller software of the main door open or closed status.

MESSAGE DISPLAY. This is how the merchandiser communicates with the outside world. Customers can see messages about how much money they have put into the merchandiser. The message display also tells customers when a selection is sold out and when vending is free, inhibited, or discounted. The message display shows you what you are doing when you program the merchandiser, and can show you what is wrong if there is a failure.

FREE VEND KEYSWITCH (OPTIONAL). This allows someone (other than maintenance personnel) to set the merchandiser to free vend without opening the door.

SELECTION SWITCH PANEL. The customer uses these switches to make selections. Also, maintenance people may use this switch panel during programming and other support modes.

COIN RETURN BUTTON. Pressing this button returns any coins that have been paid into the merchandiser prior to a vend.

BILL ACCEPTOR (OPTIONAL). Accepts bills in various denominations, depending upon the type of bill validator, and how the machine is configured.

SERVICE KEYPAD. The service keypad is located at the top of the monetary panel. It gives service personnel the means to program, retrieve data from, and view diagnostic information about, the

merchandiser.

INTERLOCK SWITCH

COIN

RETURN

COIN

BUTTON

INSERT

157P0086

Snack / Refreshment Center Setup and Operator’s Guide

Controls and Indicators (continued)

MAIN CONTROLLER

PCB ASSEMBLY

MAIN CONTROLLER PCB DISPLAY. This display consists of two light emitting diodes (LED) mounted on the controller PCB.

«CAUTION — Risk of explosion if battery is replaced with an incorrect type. Dispose of used batteries according to the manufacturer’s instructions.»

NORMAL CONDITIONS:

When the merchandiser is operating normally, you should see a steady red POWER ON indicator and a flashing red HEARTBEAT indicator. Contact a service representative if any other condition exists.

Back Side of U.S./Canada Power Panel. The circuit board mounted on the rear of the power panel is a dc power supply for the coin mechanism. A fuse protects the board circuitry in the event of a coin mechanism solenoid failure. If the coin mechanism is not working, check this fuse. If the fuse is blown, a bad coin mechanism solenoid could be at fault. (Board may not be there if machine is setup for MDB.)

Snack / Refreshment Center Setup and Operator’s Guide

LOW VOLTAGE

CIRCUIT BREAKER

•Power to the merchandiser is controlled by the main power switch, located on the power panel.

•The power panel is on the right side of the merchandiser, behind the monetary door.

WARNING

Lethal voltages are present. Unplug the merchandiser whenever you do one of the following tasks:

•Change a fuse

•Change the fluorescent lamp

•Change the lamp starter

•Connect or disconnect a harness (except a motor harness when the tray has been removed)

Failure to do so may result in personal injury.

Snack / Refreshment Center Setup and Operator’s Guide

Initial Set-Up

1. Move the Merchandiser Through a Narrow Doorway

NOTE: If necessary, this merchandiser can be moved through an opening as narrow as 30 inches by removing panels at the top and bottom of the cabinet. Merchandisers 457 and 458 are only 28” deep, and do not require panels to be removed.

REMOVABLE PANEL FOR GETTING THROUGH A NARROW DOORWAY

VIEW LOOKING INTO THE TOP OF THE CABINET

REMOVABLE PANEL

FOR GETTING THROUGH

A NARROW DOORWAY

˜

VIEW LOOKING INTO THE BOTTOM OF THE CABINET

Snack / Refreshment Center Setup and Operator’s Guide

1. Move the Merchandiser Through a Narrow Doorway

(continued)

TAKE THE MERCHANDISER

THROUGH THE OPENING:

1.Open the cabinet door and place it square with the

left side of the cabinet.

2. Carefully walk the merchandiser through the opening.

REASSEMBLE THE MER-

CHANDISER:

1.Replace the upper and lower panels.

2. Position the Merchandiser

Move the merchandiser to its approximate position. (There are some procedures you need to do before it is in its permanent location.) Plug in your merchandiser and turn the power switch to ON.

•You can position this merchandiser anywhere in a bank of machines. It can even be placed on an end flush against a side wall.

•The 167 and 168 merchandisers should be located at least one inch away from the back wall.

•The 764, 765, 784, 787, 797, and 798 merchandisers should be placed at least six inches away from the back wall. This will provide adequate air circulation for the refrigeration unit.

•The 764, 765, 787, 797, and 798 merchandisers will operate more efficiently when placed in a shaded location.

•There should be enough room in front of the merchandiser for the door to move freely.

WARNING

This machine is only rated for installation in an indoor location.

Snack / Refreshment Center Setup and Operator’s Guide

Time Out!

Now that you have placed your machine near its permanent location, you need to set up some of the special options you may have.

NOW, IF YOUR MACHINE IS EQUIPPED WITH A CAN-

MODULE . . .

Grab the booklet entitled «CAN MODULE SETUP AND OPERATOR’S GUIDE» and follow the setup procedures contained in it. After you have done that, come right back here and proceed with the next step.

Go on to the next page and continue with the snack set up.

Snack / Refreshment Center Setup and Operator’s Guide

Snack Section Set-Up

1.Place a Tray in the Loading Position

2.Place both hands on the tray as shown.

3.If your machine has tray latches, lightly push back on the tray with your palms. This will release the tray latches on the sides of the tray. Otherwise, skip to step 5.

4.Push down on the tray latches with your thumbs.

5.Pull the tray toward you until you hear and feel the rear tray rollers drop into a cut-out in the top of the guide rail. Skip to step 6

6.Lightly lift the front of the tray and pull the tray toward you until you hear and feel the tray rollers drop into the cut-out in the top of the guide rail.

.

TRAY

LATCH

PULL

TRAY

LATCH

157P0011

7.Continue pulling the tray forward for another inch. You will then be able to tilt the tray downward into the loading position as shown.

NOTE

When the cabinet door is not fully open, the bottom tray will rest on the delivery pan assembly. Handle the tray with care to avoid scratching the delivery pan assembly.

Snack / Refreshment Center Setup and Operator’s Guide

1. Set up Trays to Vend Products

These instructions will guide you through setting up your trays for vending. You will be asked to determine if your tray can physically hold the products you intend to vend. If not, you will be directed to other procedures which will help you get them set up. Follow these nine steps for each tray in your machine:

1.Make sure the tray is in the loading position.

2.Is the column wide enough for the intended product? If so, proceed to the next step. Otherwise, set up your tray to vend wider products (see below, this page). When you’re done, return to step 3 in this procedure.

3.Will the products fit between the spiral turns? If so, proceed to the next step. Otherwise, change the spiral.

4.Will the product pass under the tray immediately above? If so, proceed to the next step. Otherwise, reposition the tray and guides.

5.Will the product touch products on either side? If not, proceed to the next step. Otherwise, install a product spacer.

6.Load products in the tray.

7.Return the tray to the vending position.

8.Install the price rolls.

9.Install the selection ID numbers.

2.Set Up A Tray To Vend Wide Products

The following steps will help you configure your tray to vend wide products. When you have completed the procedures called out in each step, return to the next step in the procedure. When you are done with the entire wide product steps, return to the set-up procedures above.

1.Remove the tray from the merchandiser and place on a flat surface.

2.Based on the size of the product you want to vend, decide how many spiral positions it will occupy. Please remember that the leftmost spiral in the group must have an even ID number (0, 2, 4, etc.) For example, if a product is three spirals wide, the left spiral will be ID number 0, and the right spiral will be ID number 2. Be careful how wide you set up for, because really wide products could get hung up in the delivery door.

3.Remove the column dividers inside the group. In the example of three spiral positions, you would be removing the dividers between spiral ID numbers 0 and 1, and 1 and 2.

4.If your group only consists of 2 spirals, replace the rightmost motor with a spiral bearing and gear, and install a gear on the leftmost motor. Skip to step 8.

5.Remove all spirals in the group except the leftmost spiral.

6.Do one of the following:

a.If your group has an ODD number of spirals (3, 5, etc.) remove the harnesses from all motors in the group except the leftmost one. To the rightmost motor, connect the harness from the motor immediately to its left.

b.If your group has an EVEN number of spirals (4, 6, etc.) remove the harnesses from all motors inside the group (leave the harnesses connected to the leftmost and rightmost motors).

Snack / Refreshment Center Setup and Operator’s Guide

7.Install a spiral at the rightmost position in your group. Make sure it has the same product capacity and is opposite to the one in the leftmost position.

8.Return the tray to the merchandiser.

9.Electronically couple the motors as needed (see your Programming Guide for information).

10.Return to step 3 in the Set Up Trays to Vend Products procedure, above.

3.Removing a Tray

4.Lightly lift the front of the tray and pull the tray toward you until you hear and feel the rear tray rollers drop into a cut-out in the top of the guide rail.

TRAY

LATCH

TRAY

GUIDE

RAIL

157P0027