-
DougieLawson
- Posts: 42328
- Joined: Sun Jun 16, 2013 11:19 pm
- Location: A small cave in deepest darkest Basingstoke, UK
Re: error -110 whilst initialising MMC card
Mon Mar 02, 2015 10:55 am
nardev wrote:Installing 2015-01-31-raspbian version solved the issue
You should upgrade to the 2015-02-16 version there’s lots of kernel/firmware updates in that one.
Or run sudo apt-get update && sudo apt-get dist-upgrade
Languages using left-hand whitespace for syntax are ridiculous
DMs sent on https://twitter.com/DougieLawson or LinkedIn will be answered next month.
Fake doctors — are all on my foes list.
The use of crystal balls and mind reading is prohibited.
-
tmcolby
- Posts: 15
- Joined: Mon Sep 01, 2014 3:12 am
Re: error -110 whilst initialising MMC card
Mon Mar 02, 2015 3:42 pm
I am running into the same error. I ran raspi-config, changed i2c to load at boot, and upon reboot got this error. I reflashed the emmc to raspbian 2015-02-16. Everything appeared to load successful and then after I initially booted the error occurred. I disconnected power, did something else, and reconnected power 10 minutes later and it booted fine. Now after stepping through the default run of raspi-config on a fresh install I get the error again.
-
minipada
- Posts: 7
- Joined: Tue Mar 03, 2015 8:19 am
Re: error -110 whilst initialising MMC card
Tue Mar 03, 2015 8:25 am
Hello, I think I have the answer.
I experienced it with the compute module. I followed every advices and this is my conclusion.
When this error happens, let your board some time at rest.
After waiting a bit, it should work. It maybe is a capacitor unloading. After that it should work, make a firmware update (you’ll need a wifi dongle) and now everything works, you don’t need to wait anymore.
-
tmcolby
- Posts: 15
- Joined: Mon Sep 01, 2014 3:12 am
Re: error -110 whilst initialising MMC card
Tue Mar 03, 2015 3:20 pm
If I start out with the 2014-12-24 release of raspbian, everything is OK.
If I load the latest 2015-02-16 release, it breaks.
If I start with a load of 2014-12-24 and then do an apt-get update && apt-get upgrade it breaks.
If I start with a load of 2014-12-24 and then do an apt-get update && apt-get dist-upgrade it breaks.
-
gsh
- Raspberry Pi Engineer & Forum Moderator
- Posts: 1801
- Joined: Sat Sep 10, 2011 11:43 am
Re: error -110 whilst initialising MMC card
Tue Mar 03, 2015 3:22 pm
Try rpi-update, not sure which kernel you’ll get with apt-get update
Gordon Hollingworth PhD
Raspberry Pi — Chief Product Officer
-
gsh
- Raspberry Pi Engineer & Forum Moderator
- Posts: 1801
- Joined: Sat Sep 10, 2011 11:43 am
Re: error -110 whilst initialising MMC card
Tue Mar 03, 2015 10:24 pm
Yes,
apt-get update will get you an old firmware that contains this problem. I git bisected the firmware commits today and it’s clear between 30th January and about 12th February the firmware was broken for the compute module. I’m going to get a new Raspbian release but for now use rpi-update to get the latest firmware
Gordon
Gordon Hollingworth PhD
Raspberry Pi — Chief Product Officer
-
Blackeyv
- Posts: 18
- Joined: Tue Jan 13, 2015 8:36 am
Re: error -110 whilst initialising MMC card
Mon Mar 23, 2015 12:53 pm
I had the same problem. I started with the 2014-12-24 release of raspbian and it works perfect for months. But last week after the apt-get update. It always boots with the mmc0: error -110 whilist initialising MMC card….
And from the above replies, I think the rpi-update may fix the problem. But the thing is that I can not get the ethernet working now. It works fine for months but just dont work. I really want to know how to fix it without network. I cannot refresh the image because I have worked month with it. It is not the problem of the ethernet adapter, I tested it on my laptop.
It is strange that I type «ifconfig» and it returned nothing.
-
rotwang
- Posts: 243
- Joined: Sat Dec 07, 2013 1:12 pm
Re: error -110 whilst initialising MMC card
Tue Apr 07, 2015 2:26 pm
What’s the latest on this, 2015-02-16 appears still to be b0rked as far as the CM is concerned. What is the most recent known, tested, working release. I’ve got a bunch of these which need to be working soon.
-
gsh
- Raspberry Pi Engineer & Forum Moderator
- Posts: 1801
- Joined: Sat Sep 10, 2011 11:43 am
Re: error -110 whilst initialising MMC card
Tue Apr 07, 2015 3:28 pm
If you rpi-update the files then it’ll work fine, should be a new Raspbian release by the end of the week
Gordon
Gordon Hollingworth PhD
Raspberry Pi — Chief Product Officer
-
rotwang
- Posts: 243
- Joined: Sat Dec 07, 2013 1:12 pm
Re: error -110 whilst initialising MMC card
Tue Apr 07, 2015 7:06 pm
gsh wrote:If you rpi-update the files then it’ll work fine, should be a new Raspbian release by the end of the week
Gordon
How exactly can I «rpi-update» when the system is so badly b0rked that it won’t boot. I can’t exactly take the eMMC memory out and plug it into an ordinary raspi, that’s why I want to go back to a version that WILL boot.
-
gsh
- Raspberry Pi Engineer & Forum Moderator
- Posts: 1801
- Joined: Sat Sep 10, 2011 11:43 am
Re: error -110 whilst initialising MMC card
Tue Apr 07, 2015 7:11 pm
If you are using a Raspberry Pi to program it then rpi-update that and copy over the /boot files. Or wait for a week
Gordon Hollingworth PhD
Raspberry Pi — Chief Product Officer
-
MrBool
- Posts: 145
- Joined: Sat Jul 05, 2014 9:51 am
Re: error -110 whilst initialising MMC card
Wed Apr 08, 2015 7:05 am
rotwang wrote:
How exactly can I «rpi-update» when the system is so badly b0rked that it won’t boot. I can’t exactly take the eMMC memory out and plug it into an ordinary raspi, that’s why I want to go back to a version that WILL boot.
You can download older images here:
http://downloads.raspberrypi.org/raspbian/images/
I had the same problem — raspbian-2014-12-25 works fine. Load this image and then you can run rpi-update.
After that don’t try apt-get upgrade, it brakes system.
-
rotwang
- Posts: 243
- Joined: Sat Dec 07, 2013 1:12 pm
Re: error -110 whilst initialising MMC card
Tue Apr 21, 2015 11:51 am
gsh wrote:If you are using a Raspberry Pi to program it then rpi-update that and copy over the /boot files. Or wait for a week
It’s now rather more than a week, and I haven’t noticed an update announcement. If I missed it I apologise and would appreciate a link.
rpi-update is for people who enjoy (briefly) playing russian roulette with a shotgun. It either needs to disappear into history, or list the changes it will make and ask for confirmation before doing so.
Edit:-
Still waiting.
Last edited by rotwang on Thu Apr 30, 2015 5:47 pm, edited 1 time in total.
-
random_stranger
- Posts: 7
- Joined: Thu Apr 23, 2015 1:40 pm
Re: error -110 whilst initialising MMC card
Thu Apr 23, 2015 1:44 pm
by minipada » Tue Mar 03, 2015 8:25 am
Hello, I think I have the answer.
I experienced it with the compute module. I followed every advices and this is my conclusion.
When this error happens, let your board some time at rest.
After waiting a bit, it should work. It maybe is a capacitor unloading. After that it should work, make a firmware update (you’ll need a wifi dongle) and now everything works, you don’t need to wait anymore.
That was the answer for me! Thank you so much.
I created this account to thank you 
!
That error gave me so much grief!
Return to “Compute Module”
Содержание
- Mmc0 error 110 whilst initialising sd card
- Re: Error -110 whilst initialising SD card
- Re: Error -110 whilst initialising SD card
- mmc0: ошибка -110 при инициализации SD-карты [закрыто]
- Mmc0 error 110 whilst initialising sd card
- Re: Error -110 whilst initializing SD card
- Re: Error -110 whilst initializing SD card
- Re: Error -110 whilst initializing SD card
- Re: Error -110 whilst initializing SD card
- Re: Error -110 whilst initializing SD card
- mmc0: error -110 whilst initialising SD card [closed]
- 1 Answer 1
- mmc0: error -110 whilst initialising SD card
- 2 Answers 2
Mmc0 error 110 whilst initialising sd card
I’ve got sent a Raspberry PI 4 from a client. He told me that he first used the PI in combination with a 7″ touch Screen as a Repetier Server. But I’d think, thats rather irrelevant. After a Blackout in his House the PI didn’t do anything any more. The screen was black and nothing happend. He swoped the PI to a new PI 4 and got similar results. He sent it to me and I started Troubleshooting. First I formated a new SD-Card like described in every tutorial out there and flashed a Raspbian Image on it. Disconnected from everything else than a HDMI monitor Ethernet and Power the PI outputs the error
swoped the SD card twice with a new one but no change.
Researching on the web about this error only got me that somehow not that much People saw this error before cause there is no one with exactly this error, but a few with another Number.(I mean the -110, of course the [0.604734] is irrelevant)
All of these only tell about reformating rebooting and changing Images or SD-cards, with I all did previusly.
Anyone a Idea whats wrong with this PI?
Re: Error -110 whilst initialising SD card
Well, every tutorial you have encountered is wrong. Formatting a card before flashing an image is unnecessary, a waste of time and infinitesimally shortens the life of the card.
Does the RPi4B do what is described in the «not booting» sticky when powered up with no card and nothing plugged in to it except the PSU?
Re: Error -110 whilst initialising SD card
Can you boot with another SDCard?
Does the red light stay on constantly? Or is your power supply failing?
If both those are true then your SDCard is worn out or the /boot partition has pieces missing.
If you can boot from a second SDCard (as a rescue system)
I like fixing things with a chroot.
sudo umount /dev/sda1
sudo umount /dev/sda2
sudo fsck -f -y /dev/sda1
sudo fsck -f -y /dev/sda2
sudo mount /dev/sda2 /mnt
sudo mount /dev/sda1 /mnt/boot
sudo mount -o bind /dev /mnt/dev
sudo mount -o bind /sys /mnt/sys
sudo mount -t proc /proc /mnt/proc
cd /mnt
sudo chroot . # IMPORTANT: don’t miss that full stop.
We’ll start with a simple update of Raspbian/RaspiOS
apt update
apt dist-upgrade -y
apt install —reinstall raspberrypi-kernel raspberrypi-bootloader
Do anything else needed to fix any installation problems here.
Then undo the chroot and safely remove the «now fixed» SDCard.
exit
cd /
sudo umount /mnt/boot
sudo umount /mnt/dev
sudo umount /mnt/sys
sudo umount /mnt/proc
sudo umount
sudo eject /dev/sda
Languages using left-hand whitespace for syntax are ridiculous
DMs sent on https://twitter.com/DougieLawson or LinkedIn will be answered next month.
Fake doctors — are all on my foes list.
The use of crystal balls and mind reading is prohibited.
Источник
mmc0: ошибка -110 при инициализации SD-карты [закрыто]
Хотите улучшить этот вопрос? Обновите вопрос, чтобы он соответствовал теме Ask Ubuntu.
Закрыто 5 лет назад .
У меня проблема при попытке смонтировать SD-карту в Ubuntu 12.04. Сообщение, которое я получаю из системы:
Я в 3.5.0-24-generic ядре.
Я проверяю предыдущее ядро 3.5.0-15 и карта находится в системе. Я думаю, что это ошибка в ядре.
Я искал какое-то решение в сети. Они говорят, что моя карта мертва (но работает)
Что я должен делать?
Еще немного информации по этому вопросу здесь . Если у кого-то есть еще вопросы по поводу моего оборудования, просто спросите.
В основном эта ошибка возникает только тогда, когда SD-карта была повреждена. Но, как вы упомянули о его работе, пожалуйста, попробуйте следующие шаги и поделитесь своим мнением.
- Пожалуйста, проверьте вывод dmesg или lsusb проверьте, обнаруживает ли он SD-карту.
- Откройте приложение «Дисковая утилита» и проверьте, есть ли ваша SD-карта в списке. Если он указан, просто щелкните по нему -> Размонтировать том -> Отформатируйте том с помощью подходящей файловой системы.
- Также попробуйте смонтировать SD-карту в Windows и проверьте, работает она или нет.
Также вы можете понизить ядро, установив старое ядро / последнюю стабильную версию ядра с помощью sudo apt-get update && sudo apt-get dist-upgrade && sudo apt-get autoremove .
wget последнюю стабильную версию Kernel с веб-сайта Kernel и установите ее с sudo dpkg -i *.deb && sudo update-grub2
Пожалуйста, выберите правильное ядро во время загрузки и проверьте, хорошо ли монтируется ваша SD-карта!
Источник
Mmc0 error 110 whilst initialising sd card
I can’t boot up my new Pi
I successfully (I think!) set up my SDHC card using the instructions for «Copying an image to the SD card in Mac OS X (mostly graphical interface)» here:
I used the 2012-12-16-wheezy-raspbian.zip.torrent. Checksum checked out. All the files seem to be there when I look at the card on my Mac. But when I try to boot up, I get this line over and over
mmc0: error -110 whilst initialising SD card
Eventually, the screen just goes black.
I looked at this page for updating the firmware
However, these instructions don’t appear to include an option for Mac OS. By the way, the green light seems to blink in a 4-pattern, indicating loader.bin not launched, but loader. bin isn’t included in the installation I did (i.e., writing the image didn’t put that file on my card), and various pages I’ve looked at indicate that this file is no longer necessary.
Re: Error -110 whilst initializing SD card
Sorry you had to wait nine days for a reply.
But you did the right thing dropping the link into another post the other option is to reply to your own post so it bumps back to the top of the list the forum has such a high turnover. It is not good news yet because I’m a Windows Linux kind of guy but with a little bit of nudging I’m sure there will be Mac people here soon.
Noob is not derogatory the noob is just the lower end of the noob—geek spectrum being a noob is just your first step towards being an uber-geek
If you find a solution please post it in the wiki the forum dies too quick
Re: Error -110 whilst initializing SD card
Jim JKla wrote: Sorry you had to wait nine days for a reply.
But you did the right thing dropping the link into another post the other option is to reply to your own post so it bumps back to the top of the list the forum has such a high turnover. It is not good news yet because I’m a Windows Linux kind of guy but with a little bit of nudging I’m sure there will be Mac people here soon.
Re: Error -110 whilst initializing SD card
Re: Error -110 whilst initializing SD card
Re: Error -110 whilst initializing SD card
WhatTheDickens wrote: I can’t boot up my new Pi
I successfully (I think!) set up my SDHC card using the instructions for «Copying an image to the SD card in Mac OS X (mostly graphical interface)» here:
I used the 2012-12-16-wheezy-raspbian.zip.torrent. Checksum checked out. All the files seem to be there when I look at the card on my Mac. But when I try to boot up, I get this line over and over
mmc0: error -110 whilst initialising SD card
Eventually, the screen just goes black.
I looked at this page for updating the firmware
However, these instructions don’t appear to include an option for Mac OS. By the way, the green light seems to blink in a 4-pattern, indicating loader.bin not launched, but loader. bin isn’t included in the installation I did (i.e., writing the image didn’t put that file on my card), and various pages I’ve looked at indicate that this file is no longer necessary.
Error -110 is a timeout. If the card works in your PC but not on your Pi, then the only thing that (really) changes when you move it between the two is the connector in which it sits.
The bootloader in the Pi is a very simple ROM that will read bootcode.bin from the SD card and then run it. bootcode then loads the GPU firmware blob and the linux kernel image. This 2-stage approach allows the GPU firmware and kernel to be arbitrary since they live on the SD card. My bet is that the first stage does this in a very basic SD card mode (that all SD cards must employ when they power up) but when the kernel copied from the SD card tries to use the SD card with its all-singing all-dancing driver it fails.
In short: pins. The leaf-sping pins inside the socket have been known to dislodge/be stuck/gunked up as a result of the soldering process. Are there any that look out of alignment vertically? They should also be springy in their plastic slots.
Источник
mmc0: error -110 whilst initialising SD card [closed]
Bug reports and problems specific to development version of Ubuntu should be reported on Launchpad so that developers can see, track and fix these issues.
Closed 8 years ago .
I have a problem trying to mount a SD card in Ubuntu 12.04. The message what I get from the system is:
I’m on the 3.5.0-24-generic kernel.
I check previous kernel 3.5.0-15 and card is on the system. I think is some bug in kernel.
I was looking some solution on web. They say my card is dead (but is working)
What I should do?
Some more information on this issue here. If someone have more question about my hardware just ask.
1 Answer 1
Basically this error arises only when the SDcard got damaged. But as you mentioned its working, Please try the following steps and share your feedback.
- Please check the output of dmesg or lsusb to check whether it detects the SD card.
- Open the «Disk Utility» application and check whether your SD card is listed. If its listed, just click it -> Unmount Volume -> Format the Volume with suitable filesystem.
- Also, try mounting the SD card on Windows and check whether it is working or not.
Also, you can downgrade your kernel by installing the old kernel / latest stable kernel version with sudo apt-get update && sudo apt-get dist-upgrade && sudo apt-get autoremove .
wget the latest stable kernal from Kernel Website and install it with sudo dpkg -i *.deb && sudo update-grub2
Please select the proper kernel while booting and check whether your SD card mounts well!
Источник
mmc0: error -110 whilst initialising SD card
I have an issue with my Arch.I insert the SD I can’t detect it.
Also I find the following error kernel log:
So I can fix this?
2 Answers 2
Error -110 means timeout. Basically, your MMC controller is not able to talk correctly with your SD card. It usually happens when your card is not correctly inserted in the slot (for example the spring is pushing back your card too far) or maybe you are using a micro SD card and it is not correctly inserted in the SD card adapter. What can also happen is that your SD card adapter is slightly broken and some connections are not correctly made (e.g. your card has negotiated 4 bits mode and some lines are in fact not connected).
I’ve had the same problems with my Realtek reader. If necessary I can fill in the details (reader and card types, kernel and driver version, results of attempts to solve this).
In the end it boils down to some SD cards just not being supported by the current Realtek driver, and so far no prospect of this being solved. These cards seem to be very rare; I purchased another one as replacement and it worked, like all others I could lay my hands on. It doesn’t seem to depend on the speed class, capacity, or anything else that’s obvious. The same card is working with other readers (USB), and in my camera, for years without issues.
I’m not able to name any official source, however. Most of this has been established by the company that provided the Ubuntu distribution together with my notebook.
Источник
τοΖεη,
gena@Lenovo-B570e ~ $ lsusb
Bus 002 Device 004: ID 0bda:0139 Realtek Semiconductor Corp. RTS5139 Card Reader Controller
Bus 002 Device 003: ID 046d:c24a Logitech, Inc. G600 Gaming Mouse
Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 003: ID 0bda:58e4 Realtek Semiconductor Corp.
Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
gena@Lenovo-B570e ~ $ lsmod
Module Size Used by
bbswitch 16384 0
bnep 20480 2
rfcomm 69632 0
bluetooth 516096 10 bnep,rfcomm
binfmt_misc 20480 1
arc4 16384 2
brcmsmac 565248 0
cordic 16384 1 brcmsmac
brcmutil 16384 1 brcmsmac
b43 413696 0
mac80211 733184 2 b43,brcmsmac
nvidia 8642560 65
cfg80211 561152 3 b43,brcmsmac,mac80211
uvcvideo 90112 0
ssb 65536 1 b43
videobuf2_vmalloc 16384 1 uvcvideo
videobuf2_memops 16384 1 videobuf2_vmalloc
videobuf2_v4l2 28672 1 uvcvideo
videobuf2_core 36864 2 uvcvideo,videobuf2_v4l2
v4l2_common 16384 1 videobuf2_v4l2
videodev 180224 4 uvcvideo,v4l2_common,videobuf2_core,videobuf2_v4l2
snd_hda_codec_hdmi 53248 1
acer_wmi 20480 0
snd_hda_codec_realtek 81920 1
snd_hda_codec_generic 73728 1 snd_hda_codec_realtek
rtsx_usb_ms 20480 0
media 24576 2 uvcvideo,videodev
memstick 20480 1 rtsx_usb_ms
snd_hda_intel 36864 6
snd_hda_codec 135168 4 snd_hda_codec_realtek,snd_hda_codec_hdmi,snd_hda_codec_generic,snd_hda_intel
snd_hda_core 73728 5 snd_hda_codec_realtek,snd_hda_codec_hdmi,snd_hda_codec_generic,snd_hda_codec,snd_hda_intel
intel_rapl 20480 0
x86_pkg_temp_thermal 16384 0
snd_hwdep 16384 1 snd_hda_codec
intel_powerclamp 16384 0
coretemp 16384 0
kvm_intel 167936 0
snd_pcm 106496 6 snd_hda_codec_hdmi,snd_hda_codec,snd_hda_intel,snd_hda_core
kvm 532480 1 kvm_intel
snd_seq_midi 16384 0
snd_seq_midi_event 16384 1 snd_seq_midi
snd_rawmidi 32768 1 snd_seq_midi
snd_seq 69632 2 snd_seq_midi_event,snd_seq_midi
snd_seq_device 16384 3 snd_seq,snd_rawmidi,snd_seq_midi
snd_timer 32768 2 snd_pcm,snd_seq
snd 81920 21 snd_hda_codec_realtek,snd_hwdep,snd_timer,snd_hda_codec_hdmi,snd_pcm,snd_seq,snd_rawmidi,snd_hda_codec_generic,snd_hda_codec,snd_hda_intel,snd_seq_device
bcma 53248 3 b43,brcmsmac
dm_multipath 24576 0
irqbypass 16384 1 kvm
crct10dif_pclmul 16384 0
crc32_pclmul 16384 0
cryptd 20480 0
mei_me 36864 0
mei 102400 1 mei_me
joydev 20480 0
input_leds 16384 0
serio_raw 16384 0
soundcore 16384 1 snd
shpchp 36864 0
lpc_ich 24576 0
parport_pc 36864 0
ppdev 20480 0
ideapad_laptop 24576 0
mac_hid 16384 0
sparse_keymap 16384 2 acer_wmi,ideapad_laptop
wmi 20480 2 acer_wmi,ideapad_laptop
lp 20480 0
parport 49152 3 lp,ppdev,parport_pc
dm_mirror 24576 0
dm_region_hash 20480 1 dm_mirror
dm_log 20480 2 dm_region_hash,dm_mirror
rtsx_usb_sdmmc 28672 0
rtsx_usb 24576 2 rtsx_usb_sdmmc,rtsx_usb_ms
hid_generic 16384 0
usbhid 49152 0
hid 118784 2 hid_generic,usbhid
i915 1204224 3
i2c_algo_bit 16384 1 i915
drm_kms_helper 139264 1 i915
syscopyarea 16384 1 drm_kms_helper
ahci 36864 3
sysfillrect 16384 1 drm_kms_helper
sysimgblt 16384 1 drm_kms_helper
libahci 32768 1 ahci
psmouse 122880 0
fb_sys_fops 16384 1 drm_kms_helper
r8169 81920 0
drm 360448 9 i915,drm_kms_helper,nvidia
mii 16384 1 r8169
video 40960 3 i915,acer_wmi,ideapad_laptop
fjes 28672 0
victor00000, а как понять, что именно его?
jura12, к сожалению, нет(
У меня проблема при попытке смонтировать SD-карту в Ubuntu 12.04. Сообщение, которое я получаю из системы:
mmc0: error -110 whilst initialising SD card
Я в 3.5.0-24-genericядре.
Я проверяю предыдущее ядро 3.5.0-15 и карта находится в системе. Я думаю, что это ошибка в ядре.
Я искал какое-то решение в сети. Они говорят, что моя карта мертва (но работает)
Что я должен делать?
Еще немного информации по этому вопросу здесь . Если у кого-то есть еще вопросы по поводу моего оборудования, просто спросите.
Ответы:
В основном эта ошибка возникает только тогда, когда SD-карта была повреждена. Но, как вы упомянули о его работе, пожалуйста, попробуйте следующие шаги и поделитесь своим мнением.
- Пожалуйста, проверьте вывод
dmesgилиlsusbпроверьте, обнаруживает ли он SD-карту. - Откройте приложение «Дисковая утилита» и проверьте, есть ли ваша SD-карта в списке. Если он указан, просто щелкните по нему -> Размонтировать том -> Отформатируйте том с помощью подходящей файловой системы.
- Также попробуйте смонтировать SD-карту в Windows и проверьте, работает она или нет.
Также вы можете понизить ядро, установив старое ядро / последнюю стабильную версию ядра с помощью sudo apt-get update && sudo apt-get dist-upgrade && sudo apt-get autoremove.
wgetпоследнюю стабильную версию Kernel с веб-сайта Kernel и установите ее сsudo dpkg -i *.deb && sudo update-grub2
Пожалуйста, выберите правильное ядро во время загрузки и проверьте, хорошо ли монтируется ваша SD-карта!
WiFi on my Raspberry Pi has disappeared. This is not the first time. It occured a while ago but when I inserted an external WiFi Dongle (and did a lot of other stuff from Google), it showed up. This time, it’s not working.
Bluetooth & WiFi were working on my Raspberry Pi 3 Model B Rev 1.2 when I bought it in 2016. I did not use it for a while and in 2018, I tried OSMC and there was no WiFi. So I installed Raspbian & still no WiFi. So I Googled and tried a lot of things. Thinking it’s a hardware issue, I bought an external WiFi Dongle and as soon as I inserted it, internal WiFi showed up.
All this while, Bluetooth was working fine.
Almost 6 months later, I format the SD Card and installed latest Raspbian, and again, there is no wlan0. Tried external WiFi, it shows up, but the internal WiFi has disappeared.
I thought it’s some driver issue so I installed:
2016-05-10-raspbian-jessie(What I had used in 2016 maybe). No WiFi.2017-01-11-raspbian-jessie-> Again, No WiFi.
I have tried dtoverlay=sdtweak and dtoverlay=pi3-enable-wifi but with no success.
System
A constant error message that I got in all raspbian installation is:
mmc1: error -110 whilst initialising SDIO card
Initially, this error was with SD Card (and not SDIO) and there were some brcmfmac errors, but in older raspbian, this is all I get. I newer, sometimes there are some extra brcmfmac errors.
- Model: Raspberry Pi 3 Model B Rev 1.2
- Raspbian 2016-05-10 / 2017-01-11 / 2018-11-13
dmesg
mmc1: error -110 whilst initialising SDIO card
Additional context
Bluetooth & Ethernet are showing up. I have not tried to connect them. I have tried to format and boot up with no external hardware (except for HDMI) and still no success. I am using Logitech Wireless K400+ Keyboard / Mouse and it works. External USB WiFi dongle also works. I have yet not tried to change SD card as I have been using this for a while and I don’t have extra, but I will try that also & update here.
I tried with 32 GB (Sandisk Ultra some better class SD) and now I am getting some other errors as well.
Oh, Ethernet is working perfectly! I am posting this via my RPi with eth0.
Here are some raw output:
dmesg
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.14.79-v7+ (dc4@dc4-XPS13-9333) (gcc version 4.9.3 (crosstool-NG crosstool-ng-1.22.0-88-g8460611)) #1159 SMP Sun Nov 4 17:50:20 GMT 2018
[ 0.000000] CPU: ARMv7 Processor [410fd034] revision 4 (ARMv7), cr=10c5383d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt: Machine model: Raspberry Pi 3 Model B Rev 1.2
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] cma: Reserved 8 MiB at 0x3ac00000
[ 0.000000] On node 0 totalpages: 242688
[ 0.000000] free_area_init_node: node 0, pgdat 80c85280, node_mem_map ba39f000
[ 0.000000] Normal zone: 2133 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 242688 pages, LIFO batch:31
[ 0.000000] percpu: Embedded 17 pages/cpu @ba348000 s38720 r8192 d22720 u69632
[ 0.000000] pcpu-alloc: s38720 r8192 d22720 u69632 alloc=17*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 240555
[ 0.000000] Kernel command line: 8250.nr_uarts=0 bcm2708_fb.fbwidth=1824 bcm2708_fb.fbheight=984 bcm2708_fb.fbswap=1 vc_mem.mem_base=0x3ec00000 vc_mem.mem_size=0x40000000 dwc_otg.lpm_enable=0 console=ttyS0,115200 console=tty1 root=PARTUUID=e21979c8-02 rootfstype=ext4 elevator=deadline fsck.repair=yes rootwait quiet splash plymouth.ignore-serial-consoles
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 940232K/970752K available (7168K kernel code, 576K rwdata, 2076K rodata, 1024K init, 698K bss, 22328K reserved, 8192K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xbb800000 - 0xff800000 (1088 MB)
lowmem : 0x80000000 - 0xbb400000 ( 948 MB)
modules : 0x7f000000 - 0x80000000 ( 16 MB)
.text : 0x80008000 - 0x80800000 (8160 kB)
.init : 0x80b00000 - 0x80c00000 (1024 kB)
.data : 0x80c00000 - 0x80c9017c ( 577 kB)
.bss : 0x80c97f04 - 0x80d468b0 ( 699 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] ftrace: allocating 25287 entries in 75 pages
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] arch_timer: cp15 timer(s) running at 19.20MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
[ 0.000007] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
[ 0.000019] Switching to timer-based delay loop, resolution 52ns
[ 0.000266] Console: colour dummy device 80x30
[ 0.000283] console [tty1] enabled
[ 0.000308] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000)
[ 0.000323] pid_max: default: 32768 minimum: 301
[ 0.000643] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000657] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.001594] Disabling memory control group subsystem
[ 0.001671] CPU: Testing write buffer coherency: ok
[ 0.002084] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.002485] Setting up static identity map for 0x100000 - 0x10003c
[ 0.002605] Hierarchical SRCU implementation.
[ 0.003274] smp: Bringing up secondary CPUs ...
[ 0.004049] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.004890] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[ 0.005712] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[ 0.005816] smp: Brought up 1 node, 4 CPUs
[ 0.005827] SMP: Total of 4 processors activated (153.60 BogoMIPS).
[ 0.005832] CPU: All CPU(s) started in HYP mode.
[ 0.005836] CPU: Virtualization extensions available.
[ 0.006762] devtmpfs: initialized
[ 0.017000] random: get_random_u32 called from bucket_table_alloc+0xfc/0x24c with crng_init=0
[ 0.017764] VFP support v0.3: implementor 41 architecture 3 part 40 variant 3 rev 4
[ 0.017984] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.018001] futex hash table entries: 1024 (order: 4, 65536 bytes)
[ 0.018556] pinctrl core: initialized pinctrl subsystem
[ 0.019303] NET: Registered protocol family 16
[ 0.022046] DMA: preallocated 1024 KiB pool for atomic coherent allocations
[ 0.026932] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.026939] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.027153] Serial: AMBA PL011 UART driver
[ 0.028812] bcm2835-mbox 3f00b880.mailbox: mailbox enabled
[ 0.029273] uart-pl011 3f201000.serial: could not find pctldev for node /soc/gpio@7e200000/uart0_pins, deferring probe
[ 0.061041] bcm2835-dma 3f007000.dma: DMA legacy API manager at bb813000, dmachans=0x1
[ 0.062460] SCSI subsystem initialized
[ 0.062681] usbcore: registered new interface driver usbfs
[ 0.062732] usbcore: registered new interface driver hub
[ 0.062822] usbcore: registered new device driver usb
[ 0.070087] raspberrypi-firmware soc:firmware: Attached to firmware from 2018-11-04 16:31
[ 0.071489] clocksource: Switched to clocksource arch_sys_counter
[ 0.148408] VFS: Disk quotas dquot_6.6.0
[ 0.148496] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.148681] FS-Cache: Loaded
[ 0.148881] CacheFiles: Loaded
[ 0.157760] NET: Registered protocol family 2
[ 0.158481] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.158590] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.158776] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.158903] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.158947] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.159177] NET: Registered protocol family 1
[ 0.159636] RPC: Registered named UNIX socket transport module.
[ 0.159642] RPC: Registered udp transport module.
[ 0.159647] RPC: Registered tcp transport module.
[ 0.159652] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.161242] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 7 counters available
[ 0.164001] workingset: timestamp_bits=14 max_order=18 bucket_order=4
[ 0.171995] FS-Cache: Netfs 'nfs' registered for caching
[ 0.172587] NFS: Registering the id_resolver key type
[ 0.172613] Key type id_resolver registered
[ 0.172619] Key type id_legacy registered
[ 0.172633] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 0.174517] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 0.174641] io scheduler noop registered
[ 0.174648] io scheduler deadline registered (default)
[ 0.174818] io scheduler cfq registered
[ 0.174825] io scheduler mq-deadline registered
[ 0.174831] io scheduler kyber registered
[ 0.177524] BCM2708FB: allocated DMA memory fad10000
[ 0.177550] BCM2708FB: allocated DMA channel 0 @ bb813000
[ 0.227485] Console: switching to colour frame buffer device 228x61
[ 0.257833] bcm2835-rng 3f104000.rng: hwrng registered
[ 0.257966] vc-mem: phys_addr:0x00000000 mem_base=0x3ec00000 mem_size:0x40000000(1024 MiB)
[ 0.258458] vc-sm: Videocore shared memory driver
[ 0.258731] gpiomem-bcm2835 3f200000.gpiomem: Initialised: Registers at 0x3f200000
[ 0.268357] brd: module loaded
[ 0.277292] loop: module loaded
[ 0.277306] Loading iSCSI transport class v2.0-870.
[ 0.277995] libphy: Fixed MDIO Bus: probed
[ 0.278098] usbcore: registered new interface driver lan78xx
[ 0.278152] usbcore: registered new interface driver smsc95xx
[ 0.278167] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[ 0.306072] dwc_otg 3f980000.usb: base=0xf0980000
[ 0.506281] Core Release: 2.80a
[ 0.506293] Setting default values for core params
[ 0.506326] Finished setting default values for core params
[ 0.706589] Using Buffer DMA mode
[ 0.706595] Periodic Transfer Interrupt Enhancement - disabled
[ 0.706601] Multiprocessor Interrupt Enhancement - disabled
[ 0.706607] OTG VER PARAM: 0, OTG VER FLAG: 0
[ 0.706620] Dedicated Tx FIFOs mode
[ 0.707033] WARN::dwc_otg_hcd_init:1046: FIQ DMA bounce buffers: virt = 0xbad04000 dma = 0xfad04000 len=9024
[ 0.707061] FIQ FSM acceleration enabled for :
Non-periodic Split Transactions
Periodic Split Transactions
High-Speed Isochronous Endpoints
Interrupt/Control Split Transaction hack enabled
[ 0.707068] dwc_otg: Microframe scheduler enabled
[ 0.707116] WARN::hcd_init_fiq:459: FIQ on core 1 at 0x805ea470
[ 0.707127] WARN::hcd_init_fiq:460: FIQ ASM at 0x805ea7d8 length 36
[ 0.707139] WARN::hcd_init_fiq:486: MPHI regs_base at 0xf0006000
[ 0.707190] dwc_otg 3f980000.usb: DWC OTG Controller
[ 0.707222] dwc_otg 3f980000.usb: new USB bus registered, assigned bus number 1
[ 0.707254] dwc_otg 3f980000.usb: irq 62, io mem 0x00000000
[ 0.707304] Init: Port Power? op_state=1
[ 0.707309] Init: Power Port (0)
[ 0.707515] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.707526] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.707535] usb usb1: Product: DWC OTG Controller
[ 0.707543] usb usb1: Manufacturer: Linux 4.14.79-v7+ dwc_otg_hcd
[ 0.707551] usb usb1: SerialNumber: 3f980000.usb
[ 0.708167] hub 1-0:1.0: USB hub found
[ 0.708206] hub 1-0:1.0: 1 port detected
[ 0.708701] dwc_otg: FIQ enabled
[ 0.708706] dwc_otg: NAK holdoff enabled
[ 0.708711] dwc_otg: FIQ split-transaction FSM enabled
[ 0.708721] Module dwc_common_port init
[ 0.708940] usbcore: registered new interface driver usb-storage
[ 0.709101] mousedev: PS/2 mouse device common for all mice
[ 0.709167] IR NEC protocol handler initialized
[ 0.709173] IR RC5(x/sz) protocol handler initialized
[ 0.709177] IR RC6 protocol handler initialized
[ 0.709183] IR JVC protocol handler initialized
[ 0.709187] IR Sony protocol handler initialized
[ 0.709192] IR SANYO protocol handler initialized
[ 0.709197] IR Sharp protocol handler initialized
[ 0.709202] IR MCE Keyboard/mouse protocol handler initialized
[ 0.709207] IR XMP protocol handler initialized
[ 0.709870] bcm2835-wdt 3f100000.watchdog: Broadcom BCM2835 watchdog timer
[ 0.710125] bcm2835-cpufreq: min=600000 max=1200000
[ 0.710474] sdhci: Secure Digital Host Controller Interface driver
[ 0.710479] sdhci: Copyright(c) Pierre Ossman
[ 0.710842] mmc-bcm2835 3f300000.mmc: could not get clk, deferring probe
[ 0.711173] sdhost-bcm2835 3f202000.mmc: could not get clk, deferring probe
[ 0.711269] sdhci-pltfm: SDHCI platform and OF driver helper
[ 0.712721] ledtrig-cpu: registered to indicate activity on CPUs
[ 0.712900] hidraw: raw HID events driver (C) Jiri Kosina
[ 0.713048] usbcore: registered new interface driver usbhid
[ 0.713053] usbhid: USB HID core driver
[ 0.713826] vchiq: vchiq_init_state: slot_zero = bad80000, is_master = 0
[ 0.715357] [vc_sm_connected_init]: start
[ 0.725190] [vc_sm_connected_init]: end - returning 0
[ 0.725787] Initializing XFRM netlink socket
[ 0.725809] NET: Registered protocol family 17
[ 0.725904] Key type dns_resolver registered
[ 0.726433] Registering SWP/SWPB emulation handler
[ 0.726975] registered taskstats version 1
[ 0.732943] uart-pl011 3f201000.serial: cts_event_workaround enabled
[ 0.733019] 3f201000.serial: ttyAMA0 at MMIO 0x3f201000 (irq = 87, base_baud = 0) is a PL011 rev2
[ 0.734805] mmc-bcm2835 3f300000.mmc: mmc_debug:0 mmc_debug2:0
[ 0.734813] mmc-bcm2835 3f300000.mmc: DMA channel allocated
[ 0.792087] sdhost: log_buf @ bad07000 (fad07000)
[ 0.818903] mmc-bcm2835 3f300000.mmc: card claims to support voltages below defined range
[ 0.818912] mmc-bcm2835 3f300000.mmc: exceeding card's volts
[ 0.871537] mmc0: sdhost-bcm2835 loaded - DMA enabled (>1)
[ 0.872610] of_cfs_init
[ 0.872763] of_cfs_init: OK
[ 0.873356] Waiting for root device PARTUUID=e21979c8-02...
[ 0.921629] Indeed it is in host mode hprt0 = 00021501
[ 1.008033] random: fast init done
[ 1.053476] mmc0: host does not support reading read-only switch, assuming write-enable
[ 1.056727] mmc0: new high speed SDHC card at address aaaa
[ 1.057219] mmcblk0: mmc0:aaaa SL32G 29.7 GiB
[ 1.058719] mmcblk0: p1 p2
[ 1.097047] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[ 1.097103] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
[ 1.105958] devtmpfs: mounted
[ 1.109267] Freeing unused kernel memory: 1024K
[ 1.131875] usb 1-1: new high-speed USB device number 2 using dwc_otg
[ 1.132034] Indeed it is in host mode hprt0 = 00001101
[ 1.371900] usb 1-1: New USB device found, idVendor=0424, idProduct=9514
[ 1.371919] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 1.372593] hub 1-1:1.0: USB hub found
[ 1.372697] hub 1-1:1.0: 5 ports detected
[ 1.540580] systemd[1]: System time before build time, advancing clock.
[ 1.662055] NET: Registered protocol family 10
[ 1.663129] Segment Routing with IPv6
[ 1.683793] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 1.702106] random: systemd: uninitialized urandom read (16 bytes read)
[ 1.708114] systemd[1]: systemd 232 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN)
[ 1.708669] systemd[1]: Detected architecture arm.
[ 1.709531] systemd[1]: Set hostname to <raspberrypi>.
[ 1.711594] usb 1-1.1: new high-speed USB device number 3 using dwc_otg
[ 1.752030] random: systemd: uninitialized urandom read (16 bytes read)
[ 1.785709] random: systemd-sysv-ge: uninitialized urandom read (16 bytes read)
[ 1.841916] usb 1-1.1: New USB device found, idVendor=0424, idProduct=ec00
[ 1.841931] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 1.844633] smsc95xx v1.0.6
[ 1.935226] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-3f980000.usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:4a:5b:01
[ 2.031561] usb 1-1.2: new low-speed USB device number 4 using dwc_otg
[ 2.071618] Under-voltage detected! (0x00050005)
[ 2.166855] usb 1-1.2: New USB device found, idVendor=413c, idProduct=301a
[ 2.166870] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 2.166880] usb 1-1.2: Product: Dell MS116 USB Optical Mouse
[ 2.166889] usb 1-1.2: Manufacturer: PixArt
[ 2.171238] input: PixArt Dell MS116 USB Optical Mouse as /devices/platform/soc/3f980000.usb/usb1/1-1/1-1.2/1-1.2:1.0/0003:413C:301A.0001/input/input0
[ 2.171703] hid-generic 0003:413C:301A.0001: input,hidraw0: USB HID v1.11 Mouse [PixArt Dell MS116 USB Optical Mouse] on usb-3f980000.usb-1.2/input0
[ 2.204121] systemd[1]: Created slice User and Session Slice.
[ 2.204792] systemd[1]: Listening on Journal Socket.
[ 2.205161] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ 2.205779] systemd[1]: Created slice System Slice.
[ 2.205937] systemd[1]: Reached target Slices.
[ 2.206605] systemd[1]: Created slice system-getty.slice.
[ 2.206846] systemd[1]: Listening on udev Kernel Socket.
[ 2.271643] usb 1-1.4: new low-speed USB device number 5 using dwc_otg
[ 2.319819] i2c /dev entries driver
[ 2.421827] usb 1-1.4: New USB device found, idVendor=413c, idProduct=2003
[ 2.421849] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 2.421861] usb 1-1.4: Product: Dell USB Keyboard
[ 2.421869] usb 1-1.4: Manufacturer: Dell
[ 2.444158] input: Dell Dell USB Keyboard as /devices/platform/soc/3f980000.usb/usb1/1-1/1-1.4/1-1.4:1.0/0003:413C:2003.0002/input/input1
[ 2.512290] hid-generic 0003:413C:2003.0002: input,hidraw1: USB HID v1.10 Keyboard [Dell Dell USB Keyboard] on usb-3f980000.usb-1.4/input0
[ 2.851780] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[ 2.999914] systemd-journald[88]: Received request to flush runtime journal from PID 1
[ 3.197839] mmc1: error -84 whilst initialising SDIO card
[ 3.207199] mmc-bcm2835 3f300000.mmc: card claims to support voltages below defined range
[ 3.207210] mmc-bcm2835 3f300000.mmc: exceeding card's volts
[ 3.262991] mmc1: error -84 whilst initialising MMC card
[ 3.332820] mmc-bcm2835 3f300000.mmc: card claims to support voltages below defined range
[ 3.332838] mmc-bcm2835 3f300000.mmc: exceeding card's volts
[ 3.808211] snd_bcm2835: module is from the staging directory, the quality is unknown, you have been warned.
[ 3.810893] bcm2835_alsa bcm2835_alsa: card created with 8 channels
[ 4.406739] mmc1: error -84 whilst initialising SDIO card
[ 5.094581] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
[ 5.094923] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 5.242606] uart-pl011 3f201000.serial: no DMA platform data
[ 6.427513] Adding 102396k swap on /var/swap. Priority:-2 extents:1 across:102396k SSFS
[ 6.625474] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 6.628300] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0xCDE1
[ 7.888452] random: crng init done
[ 7.888463] random: 7 urandom warning(s) missed due to ratelimiting
[ 8.311577] Voltage normalised (0x00000000)
[ 9.757005] Bluetooth: Core ver 2.22
[ 9.757062] NET: Registered protocol family 31
[ 9.757066] Bluetooth: HCI device and connection manager initialized
[ 9.757084] Bluetooth: HCI socket layer initialized
[ 9.757093] Bluetooth: L2CAP socket layer initialized
[ 9.757115] Bluetooth: SCO socket layer initialized
[ 9.767113] Bluetooth: HCI UART driver ver 2.3
[ 9.767125] Bluetooth: HCI UART protocol H4 registered
[ 9.767128] Bluetooth: HCI UART protocol Three-wire (H5) registered
[ 9.767305] Bluetooth: HCI UART protocol Broadcom registered
[ 10.089375] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 10.089383] Bluetooth: BNEP filters: protocol multicast
[ 10.089400] Bluetooth: BNEP socket layer initialized
[ 10.137169] Bluetooth: RFCOMM TTY layer initialized
[ 10.137208] Bluetooth: RFCOMM socket layer initialized
[ 10.137234] Bluetooth: RFCOMM ver 1.11
[ 13.731395] fuse init (API version 7.26)
lsusb
Bus 001 Device 005: ID 413c:2003 Dell Computer Corp. Keyboard
Bus 001 Device 004: ID 413c:301a Dell Computer Corp.
Bus 001 Device 003: ID 0424:ec00 Standard Microsystems Corp. SMSC9512/9514 Fast Ethernet Adapter
Bus 001 Device 002: ID 0424:9514 Standard Microsystems Corp. SMC9514 Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
I ran sudo rpi-update and after that, following happened:
- No WiFi
- Bluetooth is there
- First 3 boot showed no error
- Post that,
error -110disappeared
Here’s the dmesg output:
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.14.94-v7+ (dom@dom-XPS-13-9370) (gcc version 4.9.3 (crosstool-NG crosstool-ng-1.22.0-88-g8460611)) #1193 SMP Tue Jan 22 15:34:30 GMT 2019
[ 0.000000] CPU: ARMv7 Processor [410fd034] revision 4 (ARMv7), cr=10c5383d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt: Machine model: Raspberry Pi 3 Model B Rev 1.2
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] cma: Reserved 8 MiB at 0x3ac00000
[ 0.000000] On node 0 totalpages: 242688
[ 0.000000] free_area_init_node: node 0, pgdat 80c85780, node_mem_map ba39f000
[ 0.000000] Normal zone: 2133 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 242688 pages, LIFO batch:31
[ 0.000000] percpu: Embedded 17 pages/cpu @ba348000 s38720 r8192 d22720 u69632
[ 0.000000] pcpu-alloc: s38720 r8192 d22720 u69632 alloc=17*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 240555
[ 0.000000] Kernel command line: 8250.nr_uarts=0 bcm2708_fb.fbwidth=1920 bcm2708_fb.fbheight=1080 bcm2708_fb.fbswap=1 vc_mem.mem_base=0x3ec00000 vc_mem.mem_size=0x40000000 dwc_otg.lpm_enable=0 console=ttyS0,115200 console=tty1 root=PARTUUID=e21979c8-02 rootfstype=ext4 elevator=deadline fsck.repair=yes rootwait quiet splash plymouth.ignore-serial-consoles
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 940232K/970752K available (7168K kernel code, 577K rwdata, 2080K rodata, 1024K init, 698K bss, 22328K reserved, 8192K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xbb800000 - 0xff800000 (1088 MB)
lowmem : 0x80000000 - 0xbb400000 ( 948 MB)
modules : 0x7f000000 - 0x80000000 ( 16 MB)
.text : 0x80008000 - 0x80800000 (8160 kB)
.init : 0x80b00000 - 0x80c00000 (1024 kB)
.data : 0x80c00000 - 0x80c906b4 ( 578 kB)
.bss : 0x80c97ef8 - 0x80d468f0 ( 699 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] ftrace: allocating 25296 entries in 75 pages
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] arch_timer: cp15 timer(s) running at 19.20MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
[ 0.000007] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
[ 0.000018] Switching to timer-based delay loop, resolution 52ns
[ 0.000266] Console: colour dummy device 80x30
[ 0.000285] console [tty1] enabled
[ 0.000309] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000)
[ 0.000324] pid_max: default: 32768 minimum: 301
[ 0.000645] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000659] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.001596] Disabling memory control group subsystem
[ 0.001673] CPU: Testing write buffer coherency: ok
[ 0.002087] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.002491] Setting up static identity map for 0x100000 - 0x10003c
[ 0.002614] Hierarchical SRCU implementation.
[ 0.003295] smp: Bringing up secondary CPUs ...
[ 0.004078] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.004926] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[ 0.005750] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[ 0.005855] smp: Brought up 1 node, 4 CPUs
[ 0.005866] SMP: Total of 4 processors activated (153.60 BogoMIPS).
[ 0.005871] CPU: All CPU(s) started in HYP mode.
[ 0.005875] CPU: Virtualization extensions available.
[ 0.006797] devtmpfs: initialized
[ 0.016927] random: get_random_u32 called from bucket_table_alloc+0xfc/0x24c with crng_init=0
[ 0.017695] VFP support v0.3: implementor 41 architecture 3 part 40 variant 3 rev 4
[ 0.017914] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.017932] futex hash table entries: 1024 (order: 4, 65536 bytes)
[ 0.018490] pinctrl core: initialized pinctrl subsystem
[ 0.019232] NET: Registered protocol family 16
[ 0.021978] DMA: preallocated 1024 KiB pool for atomic coherent allocations
[ 0.026788] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.026795] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.027003] Serial: AMBA PL011 UART driver
[ 0.028662] bcm2835-mbox 3f00b880.mailbox: mailbox enabled
[ 0.029124] uart-pl011 3f201000.serial: could not find pctldev for node /soc/gpio@7e200000/uart0_pins, deferring probe
[ 0.060591] bcm2835-dma 3f007000.dma: DMA legacy API manager at bb813000, dmachans=0x1
[ 0.062022] SCSI subsystem initialized
[ 0.062241] usbcore: registered new interface driver usbfs
[ 0.062292] usbcore: registered new interface driver hub
[ 0.062382] usbcore: registered new device driver usb
[ 0.070087] raspberrypi-firmware soc:firmware: Attached to firmware from 2019-01-22 16:50
[ 0.071491] clocksource: Switched to clocksource arch_sys_counter
[ 0.148486] VFS: Disk quotas dquot_6.6.0
[ 0.148567] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.148754] FS-Cache: Loaded
[ 0.148936] CacheFiles: Loaded
[ 0.156815] NET: Registered protocol family 2
[ 0.157536] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.157645] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.157830] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.157959] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.158003] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.158231] NET: Registered protocol family 1
[ 0.158702] RPC: Registered named UNIX socket transport module.
[ 0.158708] RPC: Registered udp transport module.
[ 0.158713] RPC: Registered tcp transport module.
[ 0.158718] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.160371] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 7 counters available
[ 0.163145] workingset: timestamp_bits=14 max_order=18 bucket_order=4
[ 0.171011] FS-Cache: Netfs 'nfs' registered for caching
[ 0.171640] NFS: Registering the id_resolver key type
[ 0.171670] Key type id_resolver registered
[ 0.171676] Key type id_legacy registered
[ 0.171691] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 0.173609] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 0.173741] io scheduler noop registered
[ 0.173748] io scheduler deadline registered (default)
[ 0.173914] io scheduler cfq registered
[ 0.173921] io scheduler mq-deadline registered
[ 0.173926] io scheduler kyber registered
[ 0.176645] BCM2708FB: allocated DMA memory fad10000
[ 0.176672] BCM2708FB: allocated DMA channel 0 @ bb813000
[ 0.234650] Console: switching to colour frame buffer device 240x67
[ 0.269690] bcm2835-rng 3f104000.rng: hwrng registered
[ 0.269825] vc-mem: phys_addr:0x00000000 mem_base=0x3ec00000 mem_size:0x40000000(1024 MiB)
[ 0.270283] vc-sm: Videocore shared memory driver
[ 0.270556] gpiomem-bcm2835 3f200000.gpiomem: Initialised: Registers at 0x3f200000
[ 0.280216] brd: module loaded
[ 0.289271] loop: module loaded
[ 0.289285] Loading iSCSI transport class v2.0-870.
[ 0.290001] libphy: Fixed MDIO Bus: probed
[ 0.290104] usbcore: registered new interface driver lan78xx
[ 0.290155] usbcore: registered new interface driver smsc95xx
[ 0.290171] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[ 0.318090] dwc_otg 3f980000.usb: base=0xf0980000
[ 0.518316] Core Release: 2.80a
[ 0.518325] Setting default values for core params
[ 0.518358] Finished setting default values for core params
[ 0.718621] Using Buffer DMA mode
[ 0.718628] Periodic Transfer Interrupt Enhancement - disabled
[ 0.718633] Multiprocessor Interrupt Enhancement - disabled
[ 0.718640] OTG VER PARAM: 0, OTG VER FLAG: 0
[ 0.718653] Dedicated Tx FIFOs mode
[ 0.719005] WARN::dwc_otg_hcd_init:1046: FIQ DMA bounce buffers: virt = 0xbad04000 dma = 0xfad04000 len=9024
[ 0.719031] FIQ FSM acceleration enabled for :
Non-periodic Split Transactions
Periodic Split Transactions
High-Speed Isochronous Endpoints
Interrupt/Control Split Transaction hack enabled
[ 0.719038] dwc_otg: Microframe scheduler enabled
[ 0.719092] WARN::hcd_init_fiq:459: FIQ on core 1 at 0x805ed1d4
[ 0.719103] WARN::hcd_init_fiq:460: FIQ ASM at 0x805ed53c length 36
[ 0.719117] WARN::hcd_init_fiq:486: MPHI regs_base at 0xf0006000
[ 0.719174] dwc_otg 3f980000.usb: DWC OTG Controller
[ 0.719208] dwc_otg 3f980000.usb: new USB bus registered, assigned bus number 1
[ 0.719240] dwc_otg 3f980000.usb: irq 62, io mem 0x00000000
[ 0.719289] Init: Port Power? op_state=1
[ 0.719293] Init: Power Port (0)
[ 0.719500] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.719510] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.719519] usb usb1: Product: DWC OTG Controller
[ 0.719527] usb usb1: Manufacturer: Linux 4.14.94-v7+ dwc_otg_hcd
[ 0.719536] usb usb1: SerialNumber: 3f980000.usb
[ 0.720141] hub 1-0:1.0: USB hub found
[ 0.720181] hub 1-0:1.0: 1 port detected
[ 0.720726] dwc_otg: FIQ enabled
[ 0.720731] dwc_otg: NAK holdoff enabled
[ 0.720737] dwc_otg: FIQ split-transaction FSM enabled
[ 0.720746] Module dwc_common_port init
[ 0.721020] usbcore: registered new interface driver usb-storage
[ 0.721193] mousedev: PS/2 mouse device common for all mice
[ 0.721268] IR NEC protocol handler initialized
[ 0.721273] IR RC5(x/sz) protocol handler initialized
[ 0.721278] IR RC6 protocol handler initialized
[ 0.721283] IR JVC protocol handler initialized
[ 0.721288] IR Sony protocol handler initialized
[ 0.721293] IR SANYO protocol handler initialized
[ 0.721299] IR Sharp protocol handler initialized
[ 0.721304] IR MCE Keyboard/mouse protocol handler initialized
[ 0.721309] IR XMP protocol handler initialized
[ 0.722050] bcm2835-wdt 3f100000.watchdog: Broadcom BCM2835 watchdog timer
[ 0.722335] bcm2835-cpufreq: min=600000 max=1200000
[ 0.722694] sdhci: Secure Digital Host Controller Interface driver
[ 0.722699] sdhci: Copyright(c) Pierre Ossman
[ 0.723045] mmc-bcm2835 3f300000.mmc: could not get clk, deferring probe
[ 0.723371] sdhost-bcm2835 3f202000.mmc: could not get clk, deferring probe
[ 0.723466] sdhci-pltfm: SDHCI platform and OF driver helper
[ 0.724893] ledtrig-cpu: registered to indicate activity on CPUs
[ 0.725082] hidraw: raw HID events driver (C) Jiri Kosina
[ 0.725207] usbcore: registered new interface driver usbhid
[ 0.725212] usbhid: USB HID core driver
[ 0.725990] vchiq: vchiq_init_state: slot_zero = bad80000, is_master = 0
[ 0.727556] [vc_sm_connected_init]: start
[ 0.738196] [vc_sm_connected_init]: end - returning 0
[ 0.738838] Initializing XFRM netlink socket
[ 0.738862] NET: Registered protocol family 17
[ 0.738964] Key type dns_resolver registered
[ 0.739505] Registering SWP/SWPB emulation handler
[ 0.740089] registered taskstats version 1
[ 0.746077] uart-pl011 3f201000.serial: cts_event_workaround enabled
[ 0.746162] 3f201000.serial: ttyAMA0 at MMIO 0x3f201000 (irq = 87, base_baud = 0) is a PL011 rev2
[ 0.747947] mmc-bcm2835 3f300000.mmc: mmc_debug:0 mmc_debug2:0
[ 0.747957] mmc-bcm2835 3f300000.mmc: DMA channel allocated
[ 0.812159] sdhost: log_buf @ bad07000 (fad07000)
[ 0.855972] mmc-bcm2835 3f300000.mmc: card claims to support voltages below defined range
[ 0.855981] mmc-bcm2835 3f300000.mmc: exceeding card's volts
[ 0.891229] mmc1: error -110 whilst initialising MMC card
[ 0.892495] mmc0: sdhost-bcm2835 loaded - DMA enabled (>1)
[ 0.893563] of_cfs_init
[ 0.893712] of_cfs_init: OK
[ 0.894263] Waiting for root device PARTUUID=e21979c8-02...
[ 0.941602] Indeed it is in host mode hprt0 = 00021501
[ 1.025395] random: fast init done
[ 1.073471] mmc0: host does not support reading read-only switch, assuming write-enable
[ 1.076700] mmc0: new high speed SDHC card at address aaaa
[ 1.077236] mmcblk0: mmc0:aaaa SL32G 29.7 GiB
[ 1.080089] mmcblk0: p1 p2
[ 1.125819] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[ 1.125879] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
[ 1.137690] devtmpfs: mounted
[ 1.141224] Freeing unused kernel memory: 1024K
[ 1.151553] usb 1-1: new high-speed USB device number 2 using dwc_otg
[ 1.151690] Indeed it is in host mode hprt0 = 00001101
[ 1.401845] usb 1-1: New USB device found, idVendor=0424, idProduct=9514
[ 1.401863] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 1.402620] hub 1-1:1.0: USB hub found
[ 1.402716] hub 1-1:1.0: 5 ports detected
[ 1.605605] systemd[1]: System time before build time, advancing clock.
[ 1.721643] usb 1-1.1: new high-speed USB device number 3 using dwc_otg
[ 1.736812] NET: Registered protocol family 10
[ 1.737939] Segment Routing with IPv6
[ 1.752214] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 1.771731] random: systemd: uninitialized urandom read (16 bytes read)
[ 1.777968] systemd[1]: systemd 232 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN)
[ 1.778547] systemd[1]: Detected architecture arm.
[ 1.779467] systemd[1]: Set hostname to <raspberrypi>.
[ 1.823244] random: systemd: uninitialized urandom read (16 bytes read)
[ 1.852228] usb 1-1.1: New USB device found, idVendor=0424, idProduct=ec00
[ 1.852251] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 1.855427] smsc95xx v1.0.6
[ 1.859762] random: systemd-cryptse: uninitialized urandom read (16 bytes read)
[ 1.945366] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-3f980000.usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:4a:5b:01
[ 2.041587] usb 1-1.2: new low-speed USB device number 4 using dwc_otg
[ 2.071865] Under-voltage detected! (0x00050005)
[ 2.187066] usb 1-1.2: New USB device found, idVendor=413c, idProduct=301a
[ 2.187080] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 2.187089] usb 1-1.2: Product: Dell MS116 USB Optical Mouse
[ 2.187097] usb 1-1.2: Manufacturer: PixArt
[ 2.191666] input: PixArt Dell MS116 USB Optical Mouse as /devices/platform/soc/3f980000.usb/usb1/1-1/1-1.2/1-1.2:1.0/0003:413C:301A.0001/input/input0
[ 2.192037] hid-generic 0003:413C:301A.0001: input,hidraw0: USB HID v1.11 Mouse [PixArt Dell MS116 USB Optical Mouse] on usb-3f980000.usb-1.2/input0
[ 2.291574] usb 1-1.4: new low-speed USB device number 5 using dwc_otg
[ 2.306799] systemd[1]: Listening on udev Control Socket.
[ 2.328025] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ 2.328385] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[ 2.328652] systemd[1]: Listening on fsck to fsckd communication Socket.
[ 2.328891] systemd[1]: Listening on udev Kernel Socket.
[ 2.329052] systemd[1]: Reached target Swap.
[ 2.329832] systemd[1]: Created slice User and Session Slice.
[ 2.436487] usb 1-1.4: New USB device found, idVendor=413c, idProduct=2003
[ 2.436515] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 2.436524] usb 1-1.4: Product: Dell USB Keyboard
[ 2.436532] usb 1-1.4: Manufacturer: Dell
[ 2.449375] i2c /dev entries driver
[ 2.458163] input: Dell Dell USB Keyboard as /devices/platform/soc/3f980000.usb/usb1/1-1/1-1.4/1-1.4:1.0/0003:413C:2003.0002/input/input1
[ 2.523008] hid-generic 0003:413C:2003.0002: input,hidraw1: USB HID v1.10 Keyboard [Dell Dell USB Keyboard] on usb-3f980000.usb-1.4/input0
[ 3.052762] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[ 3.134550] systemd-journald[86]: Received request to flush runtime journal from PID 1
[ 3.924797] snd_bcm2835: module is from the staging directory, the quality is unknown, you have been warned.
[ 3.930391] bcm2835_alsa bcm2835_alsa: card created with 8 channels
[ 5.178843] uart-pl011 3f201000.serial: no DMA platform data
[ 5.513658] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
[ 5.513916] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 6.537886] Adding 102396k swap on /var/swap. Priority:-2 extents:1 across:102396k SSFS
[ 7.132696] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0xCDE1
[ 7.134063] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 8.088737] random: crng init done
[ 8.088747] random: 7 urandom warning(s) missed due to ratelimiting
[ 8.311540] Voltage normalised (0x00000000)
[ 9.861867] Bluetooth: Core ver 2.22
[ 9.861926] NET: Registered protocol family 31
[ 9.861930] Bluetooth: HCI device and connection manager initialized
[ 9.861945] Bluetooth: HCI socket layer initialized
[ 9.861954] Bluetooth: L2CAP socket layer initialized
[ 9.861973] Bluetooth: SCO socket layer initialized
[ 9.871229] Bluetooth: HCI UART driver ver 2.3
[ 9.871238] Bluetooth: HCI UART protocol H4 registered
[ 9.871242] Bluetooth: HCI UART protocol Three-wire (H5) registered
[ 9.871384] Bluetooth: HCI UART protocol Broadcom registered
[ 10.210618] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 10.210627] Bluetooth: BNEP filters: protocol multicast
[ 10.210643] Bluetooth: BNEP socket layer initialized
[ 10.253563] Bluetooth: RFCOMM TTY layer initialized
[ 10.253593] Bluetooth: RFCOMM socket layer initialized
[ 10.253618] Bluetooth: RFCOMM ver 1.11
[ 12.615171] fuse init (API version 7.26)
And then, I am getting different errors in each boot. Sometimes its:
[ 1.046241] mmc1: error -22 whilst initialising SDIO card- Sometimes it’s both,
error -110&error -84on `MMC Card, such as below:
[ 1.512902] mmc1: error -84 whilst initialising MMC card
[ 1.602537] mmc-bcm2835 3f300000.mmc: card claims to support voltages below defined range
[ 1.602558] mmc-bcm2835 3f300000.mmc: exceeding card's volts
[ 1.628018] systemd[1]: System time before build time, advancing clock.
[ 1.664046] mmc1: error -110 whilst initialising MMC card
I have never seen errors like that from a Pi. There is a slight chance that the Pi is being underpowered — what does vcgencmd get_throttled report? — but I think you have faulty hardware.
@pelwell I also thought that but it had happen earlier also, but somehow it got fix when I inserted an external WiFi. Also, the errors are not consistent.
Here’s the output of vcgencmd get_throttled:
throttled=0x50000
That output tells us that the Pi has suffered from a lack of voltage since it was first started to boot. The startup process is highly parallel, and current draw can be very high depending on the exact timing of events, something that will be affected by the addition of an external USB dongle.
We recommend a 2.5A supply for all Pi 3s, and take care to use good USB cables to avoid transmission losses. Powered hubs are preferred for most USB devices.
The same adapter and cable was working fine earlier. I will update on rating here. error -84 whilst initialising SDIO Card is consistently coming up. External WiFi Dongle is working fine. Bluetooth is also fine.
I also thought that but it had happen earlier also, but somehow it got fix when I inserted an external WiFi
I will update on rating here. error -84 whilst initialising SDIO Card is consistently coming up.
Read together, these statements could seem contradictory. Does the onboard WiFi ever work or not?
I also thought that but it had happen earlier also, but somehow it got fix when I inserted an external WiFi
This happened about 6-7 months ago. The same error came up but it fixed itself. WiFi used to work back in 2016 and then in 2017. In 2018 this error came up for the first time but it recovered by itself when I inserted external WiFi.
Now, this is 2019 and it’s not recovering.
So I stand by my original assessment that you have faulty hardware, with a side order of inadequate power supply. You could try to reduce your power consumption by adding «arm_freq=600» to config.txt and «nr_cpus=1» to cmdline.txt — yes, this will cripple performance, but it is just a test for now — but I have a feeling it won’t help.
@pelwell I am trying with One+ Dash Charger 5V & 4A adapter. Will update you on the same.
So I tried with One+ Dash Charge. No power undervoltage issue.
On the first boot I got some errors similar to this (I forgot to save dmesg):
[ 25.295147] brcmfmac: brcmf_sdiod_regrw_helper: failed to read data F1@0x08000, err: -110
[ 25.295154] brcmfmac: brcmf_chip_recognition: chip backplane type 15 is not supported
[ 25.295158] brcmfmac: brcmf_sdio_probe_attach: brcmf_chip_attach failed!
[ 25.295162] brcmfmac: brcmf_sdio_probe: brcmf_sdio_probe_attach failed
[ 25.295231] brcmfmac: brcmf_ops_sdio_probe: F2 error, probe failed -19...
But on all future reboot I kept on getting:
mmc1: error -110 whilst initialising MMC card
mmc1: error -110 whilst initialising SDIO card
At the risk of sounding like a stuck record, I think your Pi has developed a hardware fault.
Well, unable to find a solution, I am also finally thinking that. If I upload images of my RPi, can someone on internet check and tell if there’s any burnt circuit or something like that? I hope I don’t sound dumb.
It’s very unlikely one could learn anything by inspection. The fact that the MMC interface sometimes find the WiFi chips suggests that there will be no obvious gross faults.
Well, damn! I did nothing wrong with my poor Raspberry Pi 3 to kill it’s WiFi. It’s sad.
It is sad — I’ve lost a few well-used (and misused) Pis over the years.
I know the issue is closed, but still sharing new dmesg output for other’s reference.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.14.94-v7+ (dom@dom-XPS-13-9370) (gcc version 4.9.3 (crosstool-NG crosstool-ng-1.22.0-88-g8460611)) #1193 SMP Tue Jan 22 15:34:30 GMT 2019
[ 0.000000] CPU: ARMv7 Processor [410fd034] revision 4 (ARMv7), cr=10c5383d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt: Machine model: Raspberry Pi 3 Model B Rev 1.2
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] cma: Reserved 8 MiB at 0x3ac00000
[ 0.000000] On node 0 totalpages: 242688
[ 0.000000] free_area_init_node: node 0, pgdat 80c85780, node_mem_map ba39f000
[ 0.000000] Normal zone: 2133 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 242688 pages, LIFO batch:31
[ 0.000000] percpu: Embedded 17 pages/cpu @ba348000 s38720 r8192 d22720 u69632
[ 0.000000] pcpu-alloc: s38720 r8192 d22720 u69632 alloc=17*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 240555
[ 0.000000] Kernel command line: 8250.nr_uarts=0 bcm2708_fb.fbwidth=720 bcm2708_fb.fbheight=480 bcm2708_fb.fbswap=1 vc_mem.mem_base=0x3ec00000 vc_mem.mem_size=0x40000000 dwc_otg.lpm_enable=0 console=ttyS0,115200 console=tty1 root=PARTUUID=e21979c8-02 rootfstype=ext4 elevator=deadline fsck.repair=yes rootwait quiet splash plymouth.ignore-serial-consoles
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 940232K/970752K available (7168K kernel code, 577K rwdata, 2080K rodata, 1024K init, 698K bss, 22328K reserved, 8192K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xbb800000 - 0xff800000 (1088 MB)
lowmem : 0x80000000 - 0xbb400000 ( 948 MB)
modules : 0x7f000000 - 0x80000000 ( 16 MB)
.text : 0x80008000 - 0x80800000 (8160 kB)
.init : 0x80b00000 - 0x80c00000 (1024 kB)
.data : 0x80c00000 - 0x80c906b4 ( 578 kB)
.bss : 0x80c97ef8 - 0x80d468f0 ( 699 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] ftrace: allocating 25296 entries in 75 pages
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] arch_timer: cp15 timer(s) running at 19.20MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
[ 0.000007] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
[ 0.000018] Switching to timer-based delay loop, resolution 52ns
[ 0.000267] Console: colour dummy device 80x30
[ 0.000286] console [tty1] enabled
[ 0.000311] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000)
[ 0.000326] pid_max: default: 32768 minimum: 301
[ 0.000645] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000660] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.001599] Disabling memory control group subsystem
[ 0.001675] CPU: Testing write buffer coherency: ok
[ 0.002090] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.002495] Setting up static identity map for 0x100000 - 0x10003c
[ 0.002618] Hierarchical SRCU implementation.
[ 0.003298] smp: Bringing up secondary CPUs ...
[ 0.004077] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.004925] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[ 0.005751] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[ 0.005855] smp: Brought up 1 node, 4 CPUs
[ 0.005866] SMP: Total of 4 processors activated (153.60 BogoMIPS).
[ 0.005872] CPU: All CPU(s) started in HYP mode.
[ 0.005876] CPU: Virtualization extensions available.
[ 0.006799] devtmpfs: initialized
[ 0.016929] random: get_random_u32 called from bucket_table_alloc+0xfc/0x24c with crng_init=0
[ 0.017699] VFP support v0.3: implementor 41 architecture 3 part 40 variant 3 rev 4
[ 0.017919] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.017936] futex hash table entries: 1024 (order: 4, 65536 bytes)
[ 0.018489] pinctrl core: initialized pinctrl subsystem
[ 0.019232] NET: Registered protocol family 16
[ 0.021975] DMA: preallocated 1024 KiB pool for atomic coherent allocations
[ 0.026783] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.026791] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.026995] Serial: AMBA PL011 UART driver
[ 0.028652] bcm2835-mbox 3f00b880.mailbox: mailbox enabled
[ 0.029114] uart-pl011 3f201000.serial: could not find pctldev for node /soc/gpio@7e200000/uart0_pins, deferring probe
[ 0.060425] bcm2835-dma 3f007000.dma: DMA legacy API manager at bb813000, dmachans=0x1
[ 0.061856] SCSI subsystem initialized
[ 0.062079] usbcore: registered new interface driver usbfs
[ 0.062130] usbcore: registered new interface driver hub
[ 0.062215] usbcore: registered new device driver usb
[ 0.070085] raspberrypi-firmware soc:firmware: Attached to firmware from 2019-01-22 16:50
[ 0.071486] clocksource: Switched to clocksource arch_sys_counter
[ 0.148555] VFS: Disk quotas dquot_6.6.0
[ 0.148637] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.148822] FS-Cache: Loaded
[ 0.149004] CacheFiles: Loaded
[ 0.156878] NET: Registered protocol family 2
[ 0.157594] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.157717] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.157903] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.158033] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.158076] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.158306] NET: Registered protocol family 1
[ 0.158779] RPC: Registered named UNIX socket transport module.
[ 0.158785] RPC: Registered udp transport module.
[ 0.158790] RPC: Registered tcp transport module.
[ 0.158795] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.160439] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 7 counters available
[ 0.163204] workingset: timestamp_bits=14 max_order=18 bucket_order=4
[ 0.171080] FS-Cache: Netfs 'nfs' registered for caching
[ 0.171710] NFS: Registering the id_resolver key type
[ 0.171742] Key type id_resolver registered
[ 0.171748] Key type id_legacy registered
[ 0.171764] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 0.173680] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 0.173812] io scheduler noop registered
[ 0.173819] io scheduler deadline registered (default)
[ 0.173983] io scheduler cfq registered
[ 0.173990] io scheduler mq-deadline registered
[ 0.173995] io scheduler kyber registered
[ 0.176713] BCM2708FB: allocated DMA memory fad10000
[ 0.176740] BCM2708FB: allocated DMA channel 0 @ bb813000
[ 0.187208] Console: switching to colour frame buffer device 90x30
[ 0.194378] bcm2835-rng 3f104000.rng: hwrng registered
[ 0.194508] vc-mem: phys_addr:0x00000000 mem_base=0x3ec00000 mem_size:0x40000000(1024 MiB)
[ 0.194937] vc-sm: Videocore shared memory driver
[ 0.195208] gpiomem-bcm2835 3f200000.gpiomem: Initialised: Registers at 0x3f200000
[ 0.204650] brd: module loaded
[ 0.213305] loop: module loaded
[ 0.213318] Loading iSCSI transport class v2.0-870.
[ 0.213958] libphy: Fixed MDIO Bus: probed
[ 0.214052] usbcore: registered new interface driver lan78xx
[ 0.214103] usbcore: registered new interface driver smsc95xx
[ 0.214118] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[ 0.242001] dwc_otg 3f980000.usb: base=0xf0980000
[ 0.442204] Core Release: 2.80a
[ 0.442213] Setting default values for core params
[ 0.442243] Finished setting default values for core params
[ 0.642496] Using Buffer DMA mode
[ 0.642502] Periodic Transfer Interrupt Enhancement - disabled
[ 0.642507] Multiprocessor Interrupt Enhancement - disabled
[ 0.642513] OTG VER PARAM: 0, OTG VER FLAG: 0
[ 0.642530] Dedicated Tx FIFOs mode
[ 0.642893] WARN::dwc_otg_hcd_init:1046: FIQ DMA bounce buffers: virt = 0xbad04000 dma = 0xfad04000 len=9024
[ 0.642917] FIQ FSM acceleration enabled for :
Non-periodic Split Transactions
Periodic Split Transactions
High-Speed Isochronous Endpoints
Interrupt/Control Split Transaction hack enabled
[ 0.642925] dwc_otg: Microframe scheduler enabled
[ 0.642970] WARN::hcd_init_fiq:459: FIQ on core 1 at 0x805ed1d4
[ 0.642981] WARN::hcd_init_fiq:460: FIQ ASM at 0x805ed53c length 36
[ 0.642993] WARN::hcd_init_fiq:486: MPHI regs_base at 0xf0006000
[ 0.643043] dwc_otg 3f980000.usb: DWC OTG Controller
[ 0.643074] dwc_otg 3f980000.usb: new USB bus registered, assigned bus number 1
[ 0.643105] dwc_otg 3f980000.usb: irq 62, io mem 0x00000000
[ 0.643152] Init: Port Power? op_state=1
[ 0.643157] Init: Power Port (0)
[ 0.643353] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.643364] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.643372] usb usb1: Product: DWC OTG Controller
[ 0.643380] usb usb1: Manufacturer: Linux 4.14.94-v7+ dwc_otg_hcd
[ 0.643388] usb usb1: SerialNumber: 3f980000.usb
[ 0.643969] hub 1-0:1.0: USB hub found
[ 0.644007] hub 1-0:1.0: 1 port detected
[ 0.644495] dwc_otg: FIQ enabled
[ 0.644501] dwc_otg: NAK holdoff enabled
[ 0.644505] dwc_otg: FIQ split-transaction FSM enabled
[ 0.644514] Module dwc_common_port init
[ 0.644725] usbcore: registered new interface driver usb-storage
[ 0.644885] mousedev: PS/2 mouse device common for all mice
[ 0.644952] IR NEC protocol handler initialized
[ 0.644958] IR RC5(x/sz) protocol handler initialized
[ 0.644963] IR RC6 protocol handler initialized
[ 0.644968] IR JVC protocol handler initialized
[ 0.644972] IR Sony protocol handler initialized
[ 0.644977] IR SANYO protocol handler initialized
[ 0.644982] IR Sharp protocol handler initialized
[ 0.644988] IR MCE Keyboard/mouse protocol handler initialized
[ 0.644993] IR XMP protocol handler initialized
[ 0.645650] bcm2835-wdt 3f100000.watchdog: Broadcom BCM2835 watchdog timer
[ 0.645902] bcm2835-cpufreq: min=600000 max=1200000
[ 0.646245] sdhci: Secure Digital Host Controller Interface driver
[ 0.646250] sdhci: Copyright(c) Pierre Ossman
[ 0.646594] mmc-bcm2835 3f300000.mmc: could not get clk, deferring probe
[ 0.646911] sdhost-bcm2835 3f202000.mmc: could not get clk, deferring probe
[ 0.647003] sdhci-pltfm: SDHCI platform and OF driver helper
[ 0.648380] ledtrig-cpu: registered to indicate activity on CPUs
[ 0.648547] hidraw: raw HID events driver (C) Jiri Kosina
[ 0.648699] usbcore: registered new interface driver usbhid
[ 0.648704] usbhid: USB HID core driver
[ 0.649415] vchiq: vchiq_init_state: slot_zero = bad80000, is_master = 0
[ 0.650794] [vc_sm_connected_init]: start
[ 0.659492] [vc_sm_connected_init]: end - returning 0
[ 0.660101] Initializing XFRM netlink socket
[ 0.660123] NET: Registered protocol family 17
[ 0.660222] Key type dns_resolver registered
[ 0.660783] Registering SWP/SWPB emulation handler
[ 0.661323] registered taskstats version 1
[ 0.667218] uart-pl011 3f201000.serial: cts_event_workaround enabled
[ 0.667286] 3f201000.serial: ttyAMA0 at MMIO 0x3f201000 (irq = 87, base_baud = 0) is a PL011 rev2
[ 0.669025] mmc-bcm2835 3f300000.mmc: mmc_debug:0 mmc_debug2:0
[ 0.669035] mmc-bcm2835 3f300000.mmc: DMA channel allocated
[ 0.722122] sdhost: log_buf @ bad07000 (fad07000)
[ 0.760673] mmc1: queuing unknown CIS tuple 0x80 (2 bytes)
[ 0.762240] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[ 0.763788] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[ 0.766565] mmc1: queuing unknown CIS tuple 0x80 (7 bytes)
[ 0.801507] mmc0: sdhost-bcm2835 loaded - DMA enabled (>1)
[ 0.802508] of_cfs_init
[ 0.802597] of_cfs_init: OK
[ 0.803169] Waiting for root device PARTUUID=e21979c8-02...
[ 0.844026] random: fast init done
[ 0.861688] Indeed it is in host mode hprt0 = 00021501
[ 0.943419] mmc1: new high speed SDIO card at address 0001
[ 0.963325] mmc0: host does not support reading read-only switch, assuming write-enable
[ 0.966573] mmc0: new high speed SDHC card at address aaaa
[ 0.966999] mmcblk0: mmc0:aaaa SL32G 29.7 GiB
[ 0.969490] mmcblk0: p1 p2
[ 0.997829] EXT4-fs (mmcblk0p2): INFO: recovery required on readonly filesystem
[ 0.997845] EXT4-fs (mmcblk0p2): write access will be enabled during recovery
[ 1.071531] usb 1-1: new high-speed USB device number 2 using dwc_otg
[ 1.071674] Indeed it is in host mode hprt0 = 00001101
[ 1.179600] EXT4-fs (mmcblk0p2): recovery complete
[ 1.217745] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[ 1.217805] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
[ 1.227231] devtmpfs: mounted
[ 1.230647] Freeing unused kernel memory: 1024K
[ 1.311798] usb 1-1: New USB device found, idVendor=0424, idProduct=9514
[ 1.311812] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 1.312413] hub 1-1:1.0: USB hub found
[ 1.312503] hub 1-1:1.0: 5 ports detected
[ 1.631535] usb 1-1.1: new high-speed USB device number 3 using dwc_otg
[ 1.643297] systemd[1]: System time before build time, advancing clock.
[ 1.761839] usb 1-1.1: New USB device found, idVendor=0424, idProduct=ec00
[ 1.761857] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 1.764599] smsc95xx v1.0.6
[ 1.781986] NET: Registered protocol family 10
[ 1.783018] Segment Routing with IPv6
[ 1.796921] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 1.815742] random: systemd: uninitialized urandom read (16 bytes read)
[ 1.822711] systemd[1]: systemd 232 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN)
[ 1.823954] systemd[1]: Detected architecture arm.
[ 1.829052] systemd[1]: Set hostname to <raspberrypi>.
[ 1.855093] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-3f980000.usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:4a:5b:01
[ 1.875035] random: systemd: uninitialized urandom read (16 bytes read)
[ 1.900436] random: systemd-sysv-ge: uninitialized urandom read (16 bytes read)
[ 2.352710] systemd[1]: Listening on udev Kernel Socket.
[ 2.353323] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ 2.353603] systemd[1]: Listening on udev Control Socket.
[ 2.353882] systemd[1]: Listening on Syslog Socket.
[ 2.354629] systemd[1]: Created slice System Slice.
[ 2.355287] systemd[1]: Created slice system-systemdx2dfsck.slice.
[ 2.358671] systemd[1]: Mounting Debug File System...
[ 2.469696] i2c /dev entries driver
[ 2.927464] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[ 2.999378] systemd-journald[87]: Received request to flush runtime journal from PID 1
[ 3.614626] brcmfmac: F1 signature read @0x18000000=0x1541a9a6
[ 3.623475] brcmfmac: brcmf_fw_map_chip_to_name: using brcm/brcmfmac43430-sdio.bin for chip 0x00a9a6(43430) rev 0x000001
[ 3.623714] usbcore: registered new interface driver brcmfmac
[ 3.665323] brcmfmac: brcmf_sdiod_ramrw: membytes transfer failed
[ 3.669653] brcmfmac: brcmf_sdio_download_code_file: error -110 on writing 388739 membytes at 0x00000000
[ 3.669727] brcmfmac: brcmf_sdio_download_firmware: dongle image file download failed
[ 3.726150] brcmfmac: brcmf_sdiod_regrw_helper: failed to write data F1@0x1000e, err: -110
[ 3.726166] brcmfmac: brcmf_sdio_htclk: HT Avail request error: -110
[ 3.730555] brcmfmac: brcmf_sdiod_regrw_helper: failed to write data F1@0x0a024, err: -110
[ 3.734840] brcmfmac: brcmf_sdiod_regrw_helper: failed to read data F1@0x1000e, err: -110
[ 3.734855] brcmfmac: brcmf_sdio_bus_stop: Failed to force clock for F2: err -110
[ 3.739115] brcmfmac: brcmf_sdiod_regrw_helper: failed to write data F1@0x0a020, err: -110
[ 3.743677] brcmfmac: brcmf_sdiod_regrw_helper: failed to write data F1@0x1000e, err: -110
[ 3.743690] brcmfmac: brcmf_sdio_htclk: HT Avail request error: -110
[ 3.788216] brcmfmac: brcmf_sdiod_regrw_helper: failed to write data F1@0x0b800, err: -110
[ 3.791768] brcmfmac: brcmf_sdiod_regrw_helper: failed to read data F1@0x0b800, err: -110
[ 3.796100] brcmfmac: brcmf_sdiod_regrw_helper: failed to read data F1@0x0b800, err: -110
[ 3.800398] brcmfmac: brcmf_sdiod_regrw_helper: failed to read data F1@0x0b800, err: -110
[ 3.803688] brcmfmac: brcmf_sdiod_regrw_helper: failed to read data F1@0x0b800, err: -110
[ 3.807854] brcmfmac: brcmf_sdiod_regrw_helper: failed to read data F1@0x0b800, err: -110
[ 3.820257] brcmfmac: brcmf_sdiod_regrw_helper: failed to read data F1@0x0c800, err: -110
[ 3.823704] brcmfmac: brcmf_sdiod_regrw_helper: failed to read data F1@0x0c800, err: -110
[ 3.827893] brcmfmac: brcmf_sdiod_regrw_helper: failed to write data F1@0x0c800, err: -110
[ 3.833636] brcmfmac: brcmf_sdiod_regrw_helper: failed to write data F1@0x0c408, err: -110
[ 3.837786] brcmfmac: brcmf_sdiod_regrw_helper: failed to read data F1@0x0c408, err: -110
[ 3.841553] brcmfmac: brcmf_sdiod_regrw_helper: failed to write data F1@0x1000a, err: -110
[ 3.841566] brcmfmac: brcmf_sdiod_set_sbaddr_window: failed at addr: 0x1000a
[ 3.845727] brcmfmac: brcmf_sdiod_regrw_helper: failed to write data F1@0x1000b, err: -110
[ 3.845735] brcmfmac: brcmf_sdiod_set_sbaddr_window: failed at addr: 0x1000b
[ 5.729808] uart-pl011 3f201000.serial: no DMA platform data
[ 6.012902] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
[ 6.013038] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 6.037381] Adding 102396k swap on /var/swap. Priority:-2 extents:1 across:102396k SSFS
[ 7.648623] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0xCDE1
[ 7.650777] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 9.359142] random: crng init done
[ 9.359152] random: 7 urandom warning(s) missed due to ratelimiting
[ 11.438336] Bluetooth: Core ver 2.22
[ 11.438420] NET: Registered protocol family 31
[ 11.438426] Bluetooth: HCI device and connection manager initialized
[ 11.438446] Bluetooth: HCI socket layer initialized
[ 11.438459] Bluetooth: L2CAP socket layer initialized
[ 11.438494] Bluetooth: SCO socket layer initialized
[ 11.464882] Bluetooth: HCI UART driver ver 2.3
[ 11.464901] Bluetooth: HCI UART protocol H4 registered
[ 11.464907] Bluetooth: HCI UART protocol Three-wire (H5) registered
[ 11.465175] Bluetooth: HCI UART protocol Broadcom registered
[ 11.743960] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 11.743970] Bluetooth: BNEP filters: protocol multicast
[ 11.743982] Bluetooth: BNEP socket layer initialized
[ 11.792830] Bluetooth: RFCOMM TTY layer initialized
[ 11.792849] Bluetooth: RFCOMM socket layer initialized
[ 11.792868] Bluetooth: RFCOMM ver 1.11
[ 11.896904] fuse init (API version 7.26)
All brcmfmac are in red.
Most probably an issue similar to what I’m facing… SDIO speed changed from 125/3=41.66 to 200/4=50.0 MHz, and your HW doesn’t support this speed.
You may get it to work adding
dtoverlay=wfx-sdio,sdio_overclock=42
to your /boot/config.txt file
@iamhssingh funny stuff isn’t it? Mine lasted for like two months and died. It’s hardware related but I will assume @MarcDorval has a good experiment me for today. I have a pile building up and I doubt these boards interface with the SDIO isn’t the issue but they are fs slow