Error 5719 netlogon

Добрый день господа. В логах рабочих станций стали появляться записи

Netlogon 5719

«Компьютер не может установить безопасный сеанс связи с контроллером домена VDK1 по следующей причине:

Отсутствуют серверы, которые могли бы обработать запрос на вход в сеть.
Это может затруднить проверку подлинности. Убедитесь, что компьютер подключен к сети. Если ошибка повторится, обратитесь к администратору домена.

Дополнительные сведения
Если данный компьютер является контроллером указанного домена, он устанавливает безопасный сеанс связи с эмулятором основного контроллера этого домена. В противном случае компьютер устанавливает безопасный сеанс
связи с произвольным контроллером данного домена.»

И еще одна с кодом 135:

«NTP-клиенту не удалось задать настроенный вручную узел в качестве источника времени из-за ошибки дублирования на «dc01.vdk1.local,0x9». Тот же источник времени «dc01.vdk1.local» был задан как настроенный вручную узел
на NTP-сервере или выбран как узел домена. NTP-клиент повторит попытку через 15 мин., а затем удвоит интервал между попытками. Ошибка: Элемент уже существует. (0x800706E0)»

Сетвые карты Wi-FI и обычные проводные.

Рабочие станции:

Win 7 Prof SP1 с актуальными обновлениями.

Win 8.1 Prof с актуальными обновлениями.

Серверы:

DC01- 2008R2 SP1 с актуальными обновлениями.

DC02- 2008R2 SP1 с актуальными обновлениями.

Ошибок в логах нет, DNS работает корректно.

Ipconfig клиента win 8.1

C:Windowssystem32>ipconfig /all

Настройка протокола IP для Windows

   Имя компьютера . . . . . . . . . : admin
   Основной DNS-суффикс . . . . . . : vdk1 . local
   Тип узла. . . . . . . . . . . . . : Гибридный
   IP-маршрутизация включена . . . . : Нет
   WINS-прокси включен . . . . . . . : Нет
   Порядок просмотра суффиксов DNS . : vdk1 . local

Адаптер беспроводной локальной сети Подключение по локальной сети* 3:

   Состояние среды. . . . . . . . : Среда передачи недоступна.
   DNS-суффикс подключения . . . . . :
   Описание. . . . . . . . . . . . . : Виртуальный адаптер Wi-Fi Direct (Майкрос
офт) #2
   Физический адрес. . . . . . . . . : 1A-1A-67-A6-96-15
   DHCP включен. . . . . . . . . . . : Да
   Автонастройка включена. . . . . . : Да

Адаптер беспроводной локальной сети Беспроводная сеть:

   DNS-суффикс подключения . . . . . :
   Описание. . . . . . . . . . . . . : Беспроводной сетевой адаптер Qualcomm Ath
eros AR9287
   Физический адрес. . . . . . . . . : F8-1A-67-A6-96-15
   DHCP включен. . . . . . . . . . . : Нет
   Автонастройка включена. . . . . . : Да
   Локальный IPv6-адрес канала . . . : fe80::30af:fc57:4aab:7e38%7(Основной)
   IPv4-адрес. . . . . . . . . . . . : 192.168.1.3(Основной)
   Маска подсети . . . . . . . . . . : 255.255.0.0
   Основной шлюз. . . . . . . . . : 192.168.1.1
   IAID DHCPv6 . . . . . . . . . . . : 83368551
   DUID клиента DHCPv6 . . . . . . . : 00-01-00-01-1A-3A-16-35-94-DE-80-43-61-C0

   DNS-серверы. . . . . . . . . . . : 192.168.1.6
                                       192.168.1.5
   NetBios через TCP/IP. . . . . . . . : Включен

Ethernet adapter VMware Network Adapter VMnet1:

   DNS-суффикс подключения . . . . . :
   Описание. . . . . . . . . . . . . : VMware Virtual Ethernet Adapter for VMnet
1
   Физический адрес. . . . . . . . . : 00-50-56-C0-00-01
   DHCP включен. . . . . . . . . . . : Нет
   Автонастройка включена. . . . . . : Да
   Локальный IPv6-адрес канала . . . : fe80::fc2c:1a35:aa54:ab30%9(Основной)
   IPv4-адрес. . . . . . . . . . . . : 172.16.132.1(Основной)
   Маска подсети . . . . . . . . . . : 255.255.255.0
   Основной шлюз. . . . . . . . . :
   IAID DHCPv6 . . . . . . . . . . . : 352342102
   DUID клиента DHCPv6 . . . . . . . : 00-01-00-01-1A-3A-16-35-94-DE-80-43-61-C0

   DNS-серверы. . . . . . . . . . . : fec0:0:0:ffff::1%1
                                       fec0:0:0:ffff::2%1
                                       fec0:0:0:ffff::3%1
   NetBios через TCP/IP. . . . . . . . : Включен

Ethernet adapter VMware Network Adapter VMnet8:

   DNS-суффикс подключения . . . . . :
   Описание. . . . . . . . . . . . . : VMware Virtual Ethernet Adapter for VMnet
8
   Физический адрес. . . . . . . . . : 00-50-56-C0-00-08
   DHCP включен. . . . . . . . . . . : Нет
   Автонастройка включена. . . . . . : Да
   Локальный IPv6-адрес канала . . . : fe80::94c7:573c:233d:ebb%11(Основной)
   IPv4-адрес. . . . . . . . . . . . : 172.16.61.1(Основной)
   Маска подсети . . . . . . . . . . : 255.255.255.0
   Основной шлюз. . . . . . . . . :
   IAID DHCPv6 . . . . . . . . . . . : 385896534
   DUID клиента DHCPv6 . . . . . . . : 00-01-00-01-1A-3A-16-35-94-DE-80-43-61-C0

Туннельный адаптер isatap.{4D325365-7CC9-442A-BA4E-8DC0146FC830}:

   Состояние среды. . . . . . . . : Среда передачи недоступна.
   DNS-суффикс подключения . . . . . :
   Описание. . . . . . . . . . . . . : Адаптер Microsoft ISATAP #2
   Физический адрес. . . . . . . . . : 00-00-00-00-00-00-00-E0
   DHCP включен. . . . . . . . . . . : Нет
   Автонастройка включена. . . . . . : Да

Туннельный адаптер isatap.{F82DCF34-2B40-447C-957F-31DC5779D863}:

   Состояние среды. . . . . . . . : Среда передачи недоступна.
   DNS-суффикс подключения . . . . . :
   Описание. . . . . . . . . . . . . : Адаптер Microsoft ISATAP #3
   Физический адрес. . . . . . . . . : 00-00-00-00-00-00-00-E0
   DHCP включен. . . . . . . . . . . : Нет
   Автонастройка включена. . . . . . : Да

Туннельный адаптер isatap.{EAEEC36C-6122-4181-81ED-0988245AE9AB}:

   Состояние среды. . . . . . . . : Среда передачи недоступна.
   DNS-суффикс подключения . . . . . :
   Описание. . . . . . . . . . . . . : Адаптер Microsoft ISATAP #4
   Физический адрес. . . . . . . . . : 00-00-00-00-00-00-00-E0
   DHCP включен. . . . . . . . . . . : Нет
   Автонастройка включена. . . . . . : Да

Туннельный адаптер isatap.{DAA8D103-5AB1-406E-A9F9-55CF96813317}:

   Состояние среды. . . . . . . . : Среда передачи недоступна.
   DNS-суффикс подключения . . . . . :
   Описание. . . . . . . . . . . . . : Адаптер Microsoft ISATAP #5
   Физический адрес. . . . . . . . . : 00-00-00-00-00-00-00-E0
   DHCP включен. . . . . . . . . . . : Нет
   Автонастройка включена. . . . . . : Да

C:Windowssystem32>

Ipconfig DC01

Настройка протокола IP для Windows

   Имя компьютера . . . . . . . . . : dc01
   Основной DNS-суффикс . . . . . . : vdk1 . local
   Тип узла. . . . . . . . . . . . . : Гибридный
   IP-маршрутизация включена . . . . : Нет
   WINS-прокси включен . . . . . . . : Нет
   Порядок просмотра суффиксов DNS . : vdk1.local

Ethernet adapter Подключение по локальной сети:

   DNS-суффикс подключения . . . . . :
   Описание. . . . . . . . . . . . . : Сетевое подключение Intel(R) PRO/1000 MT
   Физический адрес. . . . . . . . . : 00-15-17-D4-83-90
   DHCP включен. . . . . . . . . . . : Нет
   Автонастройка включена. . . . . . : Да
   IPv4-адрес. . . . . . . . . . . . : 192.168.1.6(Основной)
   Маска подсети . . . . . . . . . . : 255.255.0.0
   Основной шлюз. . . . . . . . . : 192.168.1.1
   DNS-серверы. . . . . . . . . . . : 192.168.1.5
                                       192.168.1.6
   NetBios через TCP/IP. . . . . . . . : Включен

Туннельный адаптер isatap.{CA09F9A2-183C-401A-8A9B-C6E7FA22EF3C}:

   Состояние среды. . . . . . . . : Среда передачи недоступна.
   DNS-суффикс подключения . . . . . :
   Описание. . . . . . . . . . . . . : Адаптер Microsoft ISATAP
   Физический адрес. . . . . . . . . : 00-00-00-00-00-00-00-E0
   DHCP включен. . . . . . . . . . . : Нет
   Автонастройка включена. . . . . . : Да

Туннельный адаптер Подключение по локальной сети* 2:

   Состояние среды. . . . . . . . : Среда передачи недоступна.
   DNS-суффикс подключения . . . . . :
   Описание. . . . . . . . . . . . . : Teredo Tunneling Pseudo-Interface
   Физический адрес. . . . . . . . . : 00-00-00-00-00-00-00-E0
   DHCP включен. . . . . . . . . . . : Нет
   Автонастройка включена. . . . . . : Да

DCDIAG ошибок не выдает.

Изменил параметры реестра

HKEY_LOCAL_MACHINESystemCurrentControlSetServicesTcpipParameters

Создать REG _DWORD параметр с именем DisableDHCPMediaSense

Установить десятичное значение 1
***************
Create a 32bit DWORD value, and set it to 0, this prevents Windows from changing the DhcpConnForceBroadcastFlag back to 0 (the default).
HKEY_LOCAL_MACHINESystemCurrentControlSetServicesNetlogonParameters
Value Name: ExpectedDialupDelay
Data Type: Reg_Dword
Data Value is in seconds (default = 0)
Data Range is between 0 and 600 seconds (10 minutes)
****************
Доберитесь до следующей ветки: HKEY_LOCAL_MACHINESOFTWAREMicrosoftWindows NTCurrentVersionWinlogon

Клик правой кнопкой мыши , Создать параметр DWORD.
Имя GpNetworkStartTimeoutPolicyValue, и нажмите ENTER.
Правый клик по GpNetworkStartTimeoutPolicyValue , и нажмите изменить.

Поставьте «десятичные».
Впишите значение 60 и нажмите OK.
Выйдите из редактора реестра и перезагрузите компьютер.
Если применение групповой политики не стартует, то увеличьте значение созданного параметра.

После чего ошибка стала появляться только при перезагрузке ПК. При запуске выключенного ПК ошибок в логах нет.

Подскажите куда копать? Все явные решения я уже испробывал.

Источник

title	description	ms.date	author	ms.author	manager	audience	ms.topic	ms.prod	localization_priority	ms.reviewer	ms.custom	ms.technology
Netlogon event ID 5719 or Group Policy event 1129	Event ID 5719 or Group Policy event 1129 is logged if you have a Gigabit network adapter installed on a Windows-based compute. Provides a resolution.	09/08/2020	Deland-Han	delhan	dcscontentpm	itpro	troubleshooting	windows-server	medium	kaushika, herbertm, v-jomcc	sap:problems-applying-group-policy-objects-to-users-or-computers, csstroubleshoot	windows-server-group-policy

Netlogon event ID 5719 or Group Policy event 1129 is logged when you start a domain member

This article solves the Netlogon event ID 5719 or Group Policy event 1129 that’s logged when you start a domain member.

Applies to: Windows 10 — all editions, Windows Server 2012 R2
Original KB number: 938449

Symptoms

[!IMPORTANT]
Follow the steps in this section carefully. Serious problems might occur if you modify the registry incorrectly. Before you modify it, back up the registry for restoration in case problems occur.

Consider this scenario:

You have a computer that’s running Windows 10 or Windows Server 2012 R2.
The computer is joined to a domain.
One of these conditions is true:
- The computer has a Gigabit network adapter installed.
- You secure the network access by using Network Access Protection (NAP), network authentication (by using 802.1x), or another method.

In this scenario, the following event is logged in the System log when you start the computer in Windows 8.1 and earlier versions. In Windows 10 and later versions, event 5719 is no longer logged in this situation. The following lines are recorded in Netlogon.log instead:

[CRITICAL] [960] CONTOSO: NlSessionSetup: Session setup: cannot pick trusted DC  
[SESSION] [960] No IP addresses present, skipping No DC event log

After this issue occurs, the computer is assigned an IP address:

[SESSION] [960] V6 Winsock Addrs: fe80::5faf:632a:f22c:644a%2 (1) V6WinsockPnpAddresses List used to be empty.  
[SESSION] [960] Winsock Addrs: 10.1.1.80 (1) List used to be empty.

On Windows 10 and later versions, you’ll see only events by components, depending on the Domain Controller connectivity (such as Group Policy). The following entries are recorded in the group policy debug log:

CGPApplicationService::MachinePolicyStartedWaitingOnNetwork.  
CGPMachineStartupConnectivity::CalculateWaitTimeoutFromHistory: Average is 388.
CGPMachineStartupConnectivity::CalculateWaitTimeoutFromHistory: Current is -1.
CGPMachineStartupConnectivity::CalculateWaitTimeoutFromHistory: Taking min of 776 and 30000.  
Waiting for SamSs with timeout 776

NlaQueryNetSignatures returned 1 networks  
NSI Information (Network GUID) : {395DB3C8-CE45-11E5-9739-806E6F6E6963}  
NSI Information (CompartmentId) : 1  
NSI Information (SiteId) : 134217728  
NSI Information (Network Name) :  
NlaGetIntranetCapability failed with 0x15  
There is no domain compartment  
ProcessGPOs(Machine): MyGetUserName failed with 1355.  
Opened query for NLA successfully  
NlaGetIntranetCapability returned Not Ready error. Consider it as NOT intranet capable.  

GPSVC(530.ae0) <DateTime> There is no connectivity  
GPSVC(530.8e0) <DateTime> ApplyGroupPolicy: Getting ready to create background thread GPOThread.

The first section shows the calculation for the time-out to use to bring up the network. It can be based on previous fast startups.

The second section shows that Network Location Awareness (NLA) fails to report a working network within the wait interval that’s allowed, and group policy startup processing fails. The third section shows that the Group Policy engine starts a background procedure, and then waits for one minute after a network becomes available.

Cause

This issue may occur for any of these reasons:

The Netlogon service starts before the network is ready. The network stack and adapter initialization often start at about the same time. Some network adapters and switches have link arbitration and MAC address uniqueness checks that take longer to complete than the wait time that is set for Netlogon to detect network connectivity.
Solutions that verify the health of the new network member delay the network connection and your ability to access domain controllers. If you have an automatic Direct Access channel connection enabled, it may also require more time to do than Netlogon allows.
The 802.1X authentication process delays connections to the domain controllers.
The client experiences a delay to retrieve an IP address from the DHCP server. It delays the display of the network interface.

Group Policy in Windows Vista and later versions is written to negotiate the network status that has NLA enabled. And it waits for a network that has DC connectivity. However, Group Policy may start prematurely because of a policy application. This situation is especially true when the delay in finding a network alternates between startups.

[!WARNING]
Serious problems might occur if you modify the registry incorrectly by using Registry Editor or by using another method. These problems might require that you reinstall the operating system. Microsoft cannot guarantee that these problems can be solved. Modify the registry at your own risk.

Resolution 1

To resolve this issue, install the most current driver for the Gigabit network adapter. Or, enable the PortFast option on the network switches.

Resolution 2

To resolve this issue, use the registry to change the related settings that affect DC connectivity. To do it, use the following methods.

Method 1

Adjust the firewall settings or IPSEC policies that are changed to allow DC connectivity. These changes are made when the client receives an IP address but requires more time to access a domain controller, for example, after a successful verification through Cisco NAC or Microsoft NPS Services.

Method 2

Configure the Netlogon registry setting to a value that is safely beyond the time that is required allow DC connectivity.

[!NOTE]
This is only effective if the machine already has an IP address. This applies to scenarios where a NAP solution puts the machine into a quarantine network. Use the following settings as guidelines.

Registry subkey: HKEY_LOCAL_MACHINESystemCurrentControlSetServicesNetlogonParameters
Value Name: ExpectedDialupDelay
Data Type: REG_DWORD
Data Value is in seconds (default= 0 )
Data Range is between 0 and 600 seconds (10 minutes)

For more information, see Settings for minimizing periodic WAN traffic.

Method 3

The IP stack tries to verify the IP address using an ARP broadcast. It delays the time that the IP takes to come online. You can set the ArpRetryCount registry entry to one (1), so the wait for uniqueness is shortened. To do it, follow these steps:

Start Registry Editor.
Locate and select the following subkey:
HKEY_LOCAL_MACHINESystemCurrentControlSetServicesTcpIpParameters
On the Edit menu, point to New, and then select DWORD Value.
Type ArpRetryCount.
Right-click the ArpRetryCount registry entry, and then select Modify.
In the Value data box, type 1, and then select OK.

[!NOTE]
The Data Range is between 0 and 3 (3 is default).
Exit Registry Editor.

Method 4

Reduce the Netlogon negative cache period by changing the NegativeCachePeriod registry entry in the following subkey:
HKEY_LOCAL_MACHINESYSTEMCurrentControlSetServicesNetlogonParametersNegativeCachePeriod

After you make this change, the Netlogon service doesn’t behave as if the domain controllers are offline for 45 seconds. The event 5719 is still logged. However, the event doesn’t cause any other significant problems. This setting allows member to try domain controllers earlier if the process failed previously.

Suggestion: Try to set a low value, such as three seconds. In LAN environments, you can use a value of 0 to turn off the negative cache.

For more information about this setting, see Settings for minimizing periodic WAN traffic.

Method 5

Configure the Kerberos registry setting to a value that is safely beyond the time that is required allow DC connectivity. Use the following settings as guidelines.

[!NOTE]
This setting applies only to Windows XP and Windows Server 2003 or earlier versions of these systems. Windows Vista and Windows Server 2008 and later versions use a default value of 0. This value turns off User Datagram Protocol (UDP) functionality for the Kerberos client.

Registry subkey: HKEY_LOCAL_MACHINESystemCurrentControlSetControlLsaKerberosParameters
Value name: MaxPacketSize
Data Type: REG_DWORD
Value Data: 1
Default: (depends on the system version)

For more information, see How to force Kerberos to use TCP instead of UDP in Windows.

Method 6

Disable media sense for TCP/IP by adding the following value to the Tcpip registry subkey:

Registry subkey: HKEY_LOCAL_MACHINESystemCurrentControlSetServicesTcpipParameters
Value Name: DisableDHCPMediaSense
Data Type: REG_DWORD
Value Data: 1
Value Range: Boolean ( 0 =False, 1 =True)
Default: 0 (False)

For more information, see How to disable the Media Sensing feature for TCP/IP in Windows.

Method 7

Group Policy has policy settings to control the wait time for startup policy processing:

Corporate LAN or WLAN:

Policy Folder: «Computer ConfigurationAdministrative TemplatesSystemGroup Policy»
Policy Name: «Specify startup policy processing wait time»
External LAN or WLAN:

Policy Folder: «Computer ConfigurationAdministrative TemplatesSystemGroup Policy»
Policy Name: «Specify workplace connectivity wait time for policy processing»

The time it takes Netlogon to acquire a working IP can be the basis for the setting. For Direct Access scenarios, you can measure the typical delay your user base has until the connection is established.

Method 8

If DisabledComponents registry setting is in place and has an incorrect value of 0xfffffff, either delete the key or change it to the intended value of 0xff.

[!IMPORTANT]
Internet Protocol version 6 (IPv6) is a mandatory part of Windows Vista and later versions of Windows. We do not recommend that you disable IPv6 or its components. If you do, some Windows components may not function. Additionally, system startup will be delayed for five seconds if IPv6 is disabled incorrectly by setting the DisabledComponents registry setting to a value of 0xfffffff. The correct value is 0xff.

Method 9

The behavior may be caused by a race condition between network initialization, locating a Domain Controller and processing Group Policy. If the network isn’t available, a Domain Controller won’t be located, and Group Policy processing will fail. Once the operating system has loaded and a network link is negotiated and established, background refresh of Group Policy will succeed.

You can set a registry value to delay the application of Group Policy:

Start Registry Editor.
Locate and select the following subkey:
HKEY_LOCAL_MACHINESOFTWAREMicrosoftWindows NTCurrentVersionWinlogon
On the Edit menu, point to New, and then select DWORD Value.
Type GpNetworkStartTimeoutPolicyValue.
Right-click the GpNetworkStartTimeoutPolicyValue registry entry, and then select Modify.
Under Base, select Decimal.
In the Value data box, type 60, and then select OK.
Exit Registry Editor, and then restart the computer.
If the Group Policy startup script doesn’t run, increase the value of the GpNetworkStartTimeoutPolicyValue registry entry.

More information

If you can log on to the domain without a problem, you can safely ignore event ID 5719. Because the Netlogon service may start before the network is ready, the computer may be unable to locate the logon domain controller. Therefore, event ID 5719 is logged. After the network is ready, the computer will try again to locate the logon domain controller. In this situation, the operation should be successful.

In a Netogon.log, entries that resemble the following example may be logged:

DateTime [CRITICAL] <domain>: NlDiscoverDc: Cannot find DC. DateTime [CRITICAL] <domain>: NlSessionSetup: Session setup: cannot pick trusted DC DateTime [MISC] Eventlog: 5719 (1)"<domain>" 0xc000005e ... DateTime [SESSION] WPNG: NlSetStatusClientSession: Set connection status to c000005e ... DateTime [SESSION] DeviceNetBT_Tcpip_{4A47AF53-40D3-4F92-ACDF-9B5E82A50E32}: Transport Added (10.0.64.232) -> Getting a proper IP address takes >15 seconds.

Similar errors might be reported by other components that require Domain Controller connectivity to function correctly. For example, the Group Policy may not be applied at system startup. In this case, startup scripts don’t run. The Group Policy failures may be related to the failure of Netlogon to locate a domain controller. You can set Group Policy to be more responsive to late network connectivity arrival.

Источник

I am having what appears to be either a networking or guest startup issue with Windows 2008 R2 SP1 guest machines on my VSphere Essentials setup. Configuration is:

HP BL460C G7 servers, 72GB RAM, with built in Emulex dual port 10Gb NICs and mezzanine NC632M dual port NICs (total 4 per host).

NICs connected to HP C3000 blade enclosure and GBe2C HP (Nortel) interconnect switches which are then uplinked to HP 5304 modular switch

ESXi 4.1 Update 1 with Emulex driver update

The issue I am seeing is that when Windows 2008 R2 boots (this can be on a new install or a P2Ved install) it throws a NETLOGON 5719 (unable to establish a secure connection) error in the event log followed closely by a windows time lookup failure warning. I can log in OK and the errors do not reoccur, Group Policy applies OK and the time service syncs a couple of seconds after the initial warning.

This only happens if the NIC is set to a static IP address. If I set it to DHCP (same address details as the static one), I do not get any errors at all.

What appears to be happening is that NETLOGON is starting before the network has completely initialised. I have tried making it depend on another service etc, disabled portfast/STP on the switches and have seen no change. I have also read an MS article which says it can be ignored, however I don’t like random errors and I have not seen this before in similar deployments with similar hardware. We don’t have any issues on physical servers running the same OS, even if they are in the same blade enclosure, or on Windows 2003 VMs.

Has anyone else noticed this behaviour?

Источник

Click here follow the steps to fix Netlogon Error Code 5719 and related errors.

Instructions

Step 1:



To Fix (Netlogon Error Code 5719) error you need to follow the steps below:
Download (Netlogon Error Code 5719) Repair Tool

Step 2:
Click the «Scan» button

Step 3:
Click ‘Fix All‘ and you’re done!

Compatibility: Windows 7, 8, Vista, XP Download Size: 6MB Requirements: 300 MHz Processor, 256 MB Ram, 22 MB HDD Limitations: This download is a free evaluation version. To unlock all features and tools, a purchase is required.

Netlogon Error Code 5719 Error Codes are caused in one way or another by misconfigured system files
in your windows operating system.

If you have Netlogon Error Code 5719 errors then we strongly recommend that you

Download (Netlogon Error Code 5719) Repair Tool.

This article contains information that shows you how to fix
Netlogon Error Code 5719
both
(manually) and (automatically) , In addition, this article will help you troubleshoot some common error messages related to Netlogon Error Code 5719 error code that you may receive.

Note:
This article was updated on 2023-02-03 and previously published under WIKI_Q210794

1. What is Netlogon Error Code 5719 error?
2. What causes Netlogon Error Code 5719 error?
3. How to easily fix Netlogon Error Code 5719 errors

What is Netlogon Error Code 5719 error?

The Netlogon Error Code 5719 error is the Hexadecimal format of the error caused. This is common error code format used by windows and other windows compatible software and driver vendors.

This code is used by the vendor to identify the error caused. This Netlogon Error Code 5719 error code has a numeric error number and a technical description. In some cases the error may have more parameters in Netlogon Error Code 5719 format .This additional hexadecimal code are the address of the memory locations where the instruction(s) was loaded at the time of the error.

What causes Netlogon Error Code 5719 error?

The Netlogon Error Code 5719 error may be caused by windows system files damage. The corrupted system files entries can be a real threat to the well being of your computer.

There can be many events which may have resulted in the system files errors. An incomplete installation, an incomplete uninstall, improper deletion of applications or hardware. It can also be caused if your computer is recovered from a virus or adware/spyware
attack or by an improper shutdown of the computer. All the above actives
may result in the deletion or corruption of the entries in the windows
system files. This corrupted system file will lead to the missing and wrongly
linked information and files needed for the proper working of the
application.

How to easily fix Netlogon Error Code 5719 error?

There are two (2) ways to fix Netlogon Error Code 5719 Error:

Advanced Computer User Solution (manual update):

1) Start your computer and log on as an administrator.

2) Click the Start button then select All Programs, Accessories, System Tools, and then click System Restore.

3) In the new window, select «Restore my computer to an earlier time» option and then click Next.

4) Select the most recent system restore point from the «On this list, click a restore point» list, and then click Next.

5) Click Next on the confirmation window.

6) Restarts the computer when the restoration is finished.

Novice Computer User Solution (completely automated):

1) Download (Netlogon Error Code 5719) repair utility.

2) Install program and click Scan button.

3) Click the Fix Errors button when scan is completed.

4) Restart your computer.

How does it work?

This tool will scan and diagnose, then repairs, your PC with patent
pending technology that fix your windows operating system registry
structure.
basic features: (repairs system freezing and rebooting issues , start-up customization , browser helper object management , program removal management , live updates , windows structure repair.)

Источник

Remove From My Forums

Question
Hello

I have been looking to fix the Event ID 1014 and 5719 errors when a client logs on to the domain. The errors are:

1014 — Name resolution failed

5719 — This computer was not able to set up a secure session with a domain controller in domain dur to the following…….

I have followed te technet articles to fix the errors but with no joy. Spanning tree portfast is enabled. One thing is that on the Domain Controllers their preferred DNS entry is 127.0.0.1
and the secodnary is the other Domain Controller.

any thoughts would be great
- Moved by
  
  Wednesday, July 11, 2012 7:03 AM
  (From:Group Policy)

Answers

- Marked as answer by
  Cicely Feng
  Monday, July 16, 2012 7:20 AM
- Proposed as answer by
  Ace Fekay [MCT]
  Friday, July 13, 2012 4:53 AM
- Marked as answer by
  Cicely Feng
  Monday, July 16, 2012 7:20 AM
Hi

We have been getting alot of DNS 1014 errors and 5719 errors when clients log onto their child domain.

I have noticed on the Domain Controller under DNS in the child domain that under forward Lookup Zones there is one folder child.domain.com. Under here there is:

_msdcs.child.domain.com

_sites

_tcp

_udp

Is this correct?. I ask because in my test environment I created a delegation and an extra set of folders appeared in my child domain on the Domain Controller in the DNS console. I had in addition to the above folders I also had:

_msdcs.domain.com

_dc

_domain

_gc

_pdc

When these appeared I then did not get any DNS errors in event viewer and logging on seemed quicker

Is this the correct setup

Thanks

GCs are only listed at the root domain level under the gc._msdcs.domain.com zone.

.

The logon errors you are seeing are more than likely due to your parent-child DNS design. So it largely depends on how you’ve designed DNS to support your multi-domain environment. Please read my blog on your DNS design options that Sandesh posted.
It should answer all of your questions and guide you in straightening it all out.

.

Ace Fekay
MVP, MCT, MCITP EA, MCTS Windows 2008/R2, Exchange 2007 & Exchange 2010, Exchange 2010 EA, MCSE & MCSA 2003/2000, MCSA Messaging 2003
Microsoft Certified Trainer
Microsoft MVP — Directory Services
Complete List of Technical Blogs: http://www.delawarecountycomputerconsulting.com/technicalblogs.php

This post is provided AS-IS with no warranties or guarantees and confers no rights.
- Proposed as answer by
  Meinolf Weber
  Friday, July 13, 2012 6:22 AM
- Marked as answer by
  Cicely Feng
  Monday, July 16, 2012 7:20 AM

Источник

KB ID 0000712

Problem

You see the following error in your event log (seen here in the system log on a domain controller).

Log Name: System
Source: NETLOGON
Date: 15/11/2012 06:00:35
Event ID: 5719
Task Category: None
Level: Error
Keywords: Classic
User: N/A
Computer: Servername.Domain-Name.com
Description:
This computer was not able to set up a secure session with a domain controller in domain (domain-name) due to the following:
There are currently no logon servers available to service the logon request.
This may lead to authentication problems. Make sure that this computer is connected to the network. If the problem persists, please contact your domain administrator.

Solution

Note: In this case the domain it could not contact was NOT my live domain name it was a different domain name. If your error is referencing your live domain name then you have a different problem.

Cause: In my case the problem was being caused because I had a domain trust to a domain that was no longer contactable, (one of my colleagues has set it up in the past to do some testing). So I simply needed to remove the trust.

Warning: In this case that trust is no longer required – Check!

1. On a domain controller > Windows Key+R > domain.msc {enter}

2. Right click the domain name > Properties > Trusts > Select the problem domain > Remove > Yes > OK.

Netlogon event ID 5719 or Group Policy event 1129 is logged when you start a domain member

Symptoms

Cause

Resolution 1

Resolution 2

Method 1

Method 2

Method 3

Method 4

Method 5

Method 6

Method 7

Method 8

Method 9

More information

Contents

What is Netlogon Error Code 5719 error?

What causes Netlogon Error Code 5719 error?

How to easily fix Netlogon Error Code 5719 error?

Question

Answers

Problem

Solution

Related Articles, References, Credits, or External Links

Читайте также:

Netlogon event ID 5719 or Group Policy event 1129 is logged when you start a domain member

Symptoms

Cause

Resolution 1

Resolution 2

Method 1

Method 2

Method 3

Method 4

Method 5

Method 6

Method 7

Method 8

Method 9

More information

Contents

What is Netlogon Error Code 5719 error?

What causes Netlogon Error Code 5719 error?

How to easily fix Netlogon Error Code 5719 error?

<img decoding="async" onError="javascript: wp_broken_images = window.wp_broken_images || function(){}; wp_broken_images(this);" src="https://errorwiki.org/wiki/images/FreeDownload.png" width="313" height="54" />

Question

Answers

Problem

Solution

Related Articles, References, Credits, or External Links

Читайте также: