Error 605 mimaki - Исправление ошибок и поиск оптимальных решений проблем

ERROR605 !REPLACE WIPER or !CLEANING WIPER (or “REPLACE WIPER” is displayed in the local screen)

Answer: Please see followings:

The wiper wipes off ink stuck on the head nozzle surface. If the wiper gets dirty, the warning message “!REPLACE WIPER” or “!CLEANING WIPER” appears to prompt the cleaning (or replacement) of the wiper. Please clean (or replace) the wiper. The wiper needs to be replaced roughly every six months. However, if the nozzle missing or ink dripping is not solved even after cleaning the wiper, replace it.

[Cleaning (replacement) procedure]

Execute [MAINTENANCE] -> [STATION] -> [MENT: WIPER EXCHG] or
　　　　[MENT: WIPER CLEANING].

* Either “WIPER EXCHG” or “WIPER CLEANING” is displayed depending on the firmware version of the main unit.
* The firmware is a program that controls the main unit.

* The warning message continues to be displayed unless you execute the “WIPER EXCHG (WIPER CLEANING)” menu after replacing the wiper. This is because the internal wiping count is only reset when the “WIPER EXCHG (WIPER CLEANING)” menu is executed.

Mimaki Europe BV
Stammerdijk 7E
1112 AA Diemen
Netherlands
t. +31 (0) 20 462 76 40
e. info@mimakieurope.com

location image

Источник

Dealing with Problems
Problems Indicated by Messages
Error Messages

Problems Indicated by Messages

Check the error details in the following table corresponding to the error numbers displayed:
If the problem persists even after carrying out the corrective action corresponding to the error number, contact your local distributor, our sales office, or service center. .

Error number/Message	Cause	Corrective action
401 MOTOR X	The X motor was overloaded.	Check the following points: Check to confirm the sheet is loaded correctly. Loading a Sheet Check for anything that may obstruct carriage movement. Set the sheet setting to «HEAVY». When using roll sheet, feed to pull out the required amount of sheet in advance to provide sufficient slack. Turn off the power and wait a while before turning the power back on. Turning Off the Power
402 MOTOR Y	The Y motor was overloaded.
403 X Current	An overcurrent was detected in the X motor.
404 Y Current	An overcurrent was detected in the Y motor.
41b NO MEDIA	An enabling operation was performed after sheet detection.	Perform sheet detection.
50a Y ORIGIN	A problem was detected with Y origin detection (initialization).	Turning Off the Power
50b FRONT EDGE	A problem was detected with the front paper sensor.
50c WIDTH	A problem was detected with sheet width detection.
520 REAR EDGE	A problem was detected with the rear paper sensor.
901 OPERATION	An inappropriate operation was performed on the operating panel.	The operation is invalid.
902 DAT REMAIN	An inappropriate operation was performed while pausing.	Either press the [REMOTE] key to cut the data or clear the data to abort the cut.
C02 MAIN RAM	An error occurred in the control RAM.	Contact your local distributor, our sales office, or service center.
C04 EEPROM	An error occurred in the system ROM.
C06 BUFFER	An error occurred in the receive buffer.
C08 POWER	An error occurred related to the motor.
C10 Commands	Received a code other than a COMMAND code.	Check the following points: Clear the data and resend. Turning Off the Power Check the USB cable connection. Using a USB Cable Use a compliant USB cable. USB Connection Precautions
C11 PARAMETER	Received parameter outside numerical value range
C12 DEVICE	Received an invalid device control command.
C13 PM OVER	The polygon buffer overflowed.	Either set so as not to use polygon commands or use the MGL-lc1 command.
C15 AUTO FEED	The length specified by the ZX command could not be fed.	Reset the long sheet after data has been sent from the host computer, then perform multiple sheet cutting.
The previous sheet length could not be fed for the second sheet data onward during divided cutting.	Load a long sheet, then switch to remote mode again.
C16 AUTO I/F	The command could not be automatically recognized.	Set the command name. SET UP
C20 I/O	An error occurred in the communication conditions.	Adjust the communication conditions to match the host computer. SET UP > [INTERFACE]
C27 BUFFERover	An error occurred in the interface.	Check the interface cable.
C31 NO DATA	Multiple sheet cutting was executed, but no data is saved to the receive buffer.	Cut the data involved once more.
C32 DATAtooBIG	The received data is too big for multiple sheet cutting.	Change the data size.
C33 SHEET SIZE	The sheet is too short in the feed direction.	Use a longer sheet.
C36 MARK DETECT	Unable to detect register marks	Check the following points: Check to confirm the register marks are placed properly. Register Marks Use an uncurled sheet. Check the mark detection start position. Check to confirm the register marks are black and printed on a white background. Check to confirm the area between the register marks is clean and free of printing and images. Check to confirm there are no errors in the mark detection settings. If the area around the register marks is filled in, set [MARK DETECT] > [MARK FILL UP] setting to «ON».
C37 MARK ORG	The register mark detection result shows that the register marks were outside the register mark reading range.	Set the register marks within the register mark reading range. Reading Range of Register Marks
C38 MARK SCALE	Register mark detection was performed, but the calculated correction value is abnormal, so either the detection was erroneous or the correction value was incorrectly specified.	Check the correction value and repeat detection.
The calculated scale compensation value was 1.3 or more or 0.7 or less.	Eliminate any causes of mis-detection, such as blurred printed register mark data, before repeating.
Mis-detected due to being too close to the adjacent image.	Ensure an appropriate distance from the adjacent image before printing again.
The specified register mark spacing is incorrect.	Invalid register mark spacing was specified by the command, or data was incorrectly selected. Check the data to be output.
Images were skipped due to the printed register marks not being aligned.	Align the data and repeat printing.
Printed register marks were not correctly read due to problems such as blurred register marks, and the register marks for the adjacent image were read instead.	Repeat printing, taking care to prevent blurring.
C39 MARK ID	Register mark IDs could not be detected. (Data with IDs)	Check the following points: Check to confirm that the paper is not curled. Check to confirm the register mark IDs are black printed on a white background. Use three pinch rollers when using thin sheets or sheets more than approximately 800 mm wide.
C51 PINCH POS*	The pinch rollers are not over the grit rollers.	Reposition the pinch rollers above the grit rollers.
C60 PenEncoder	Unable to detect pen height	Turn off the power and wait a while before turning the power back on. Turning Off the Power
C61 Pen Stroke	The pen height is incorrect.	Check the following points: Make sure the pen line rubber is not worn or deformed and remains intact. Check to confirm nothing adheres to the pen line rubber. After installing the pen in a commercially available pen holder, check to confirm the installed position is correct.

Источник

MAINTENANCE MANUAL > Troubleshooting > Details on Errors and Malfunctions > List of Error Messages

Model SWJ-320S Issued 2012.07.19 Revised 2013.03.08 F/W ver

7.1.2 List of Error Messages

 List of Error Messages ?2/5?

No.

LCD

ERROR 151

MAIN PCB V1R2

ERROR 152

MAIN PCB V2R5

ERROR 153

MAIN PCB V3R3

ERROR 154

MAIN PCB V05

ERROR 155

MAIN PCB V36-1

ERROR 156

MAIN PCB V5B

ERROR 157

MAIN PCB VTT

ERROR 158

MAIN PCB V36-2

ERROR 18a

MAIN PCB V_CORE

ERROR 18b

MAIN PCB V3R3B

ERROR 18c

MAIN PCB V12

ERROR 15f

HEAD DRIVE HOT

ERROR 171

NEW HEAD CONNECT

ERROR 186

HDC OVERFLOW

ERROR 186

HDC UNDERFLOW

ERROR 187

HDC SLEW RATE

ERROR 188

HDC MEMORY

ERROR 18e

FLS NOT COMP [12__]

ERROR 18f

OFFSET START [12__]

ERROR 18f

OFFSET END [12__]

Cause

Main board 1.2V power supply is abnor-

mal.

Main board 2.5V power supply is abnor-

mal.

Main board 3.3V power supply is abnor-

mal.

Main board 5V power supply is abnormal.

Main board 36-1V power supply is abnor-

mal.

Main board 5VB power supply is abnor-

mal.

Main board VTT power supply is abnor-

mal.

Main board 36-2V power supply is abnor-

mal.

Main board V_CORE power supply is

abnormal.

Main board 1.5V power supply is abnor-

mal.

Main board 12V power supply is abnor-

mal.

COM driver becomes the high tempera-

ture.

New Print Head was recognized.

Compare S/N written in the head memory

with S/N stored in the machine.

Wave shape overflow

Wave shape data is abnormal.

Wave shape underflow

Wave shape data is abnormal.

Wave shape slew rate error

Wave shape data is abnormal.

Wave shape memory error

At wave shape memory writing, it cannot

be written due to address conflict.

Flashing control error

Flashing for the head which is connected

the HDC PCB that displayed number on

the LCD can not be completed.

Control error to Head voltage

Offset of the HDC PCB that displayed

number on the LCD can not be started.

Control error to Head voltage

Offset of the HDC PCB that displayed

number on the LCD can not be ended.

Remark

1.0

List of Countermeasures

1. Check the output pressure of the DC power supply (36V)

and the DC power supply (5V).

2. Replace the power supply above.

3. Replace the MAIN PCB with a new one.

1. Check the operation of the HDC PCB cooling fan.

2. Disconnect and connect the FFC located between the

HDC PCB and the MAIN PCB.

3. Replace the HDC PCB with a new one.

4. Replace the Print Head with a new

It is normal that an error occurs only at the time of the first

start after having connected a new head.

It is abnormal that an error occurs at the time of start every

time..

1. Check connection between the HDC PCB from the Print

Head

2. Replace the HDC PCB with a new one.

3. Replace the Print Head with a new

1. Pull out/ insert cable between HDC PCB and MAIN PCB.

(FFC changes PCB, Optical conversion PCB)

2. Replace the HDC PCB with a new one.

3. Replace the Optical conversion PCB with a new one.

4. Replace the FFC changes PCB with a new one.

5. Replace cable between HDC PCB and MAIN PCB.

6. Replace the MAIN PCB with a new

1. Pull out/ insert cable between HDC PCB and MAIN PCB.

(FFC changes PCB, Optical conversion PCB)

2. Replace the HDC PCB with a new one.

3. Replace the Optical conversion PCB with a new one.

4. Replace the FFC changes PCB with a new one.

5. Replace cable between HDC PCB and MAIN PCB.

6. Replace the MAIN PCB with a new

7. Replace the Print Head which is connected HDC PCB that

displays error with a new

one.

Rev.

1.2

(Refer to 3.3.1)

(Refer to 6.4.7)

one.

(Refer to 3.3.1)

(Refer to 6.4.7)

one.

(Refer to 3.3.1)

one.(Refer to 3.3.1)

(Refer to 3.3.1)

7.1.2

R.1.2

P.2

Источник

Catalog
Sign In
Contacts
Forum
Eng

Error Codes
Mimaki
UJF6042
All codes

Error Codes List page 15

Code: 511
Display: SYSTEM HALT (*) 511 : Z ORGIN
Description: Z-origin error (Origin of Z-axis can not be detected)
Remedy: 1. Execute and confirm [#TEST]->[SENSOR TEST]-> [TBL-ORG]. 2. Check the connection of connector of the Z-origin Sensor. 3. Replace the Z-origin Sensor with a new one. 4. Disconnect and connect the connector of the ZMotor( Stepping motor). 5. Replace the Station III PCB with a new one.

Code: 601
Display: ERROR 601 INK NEAREND
Description: Ink near end (A small amount of ink left)
Remedy: (When the message is still displayed even after a new Ink Cartridge or an empty Ink Cartridge is charged;) 1. Execute and confirm [#TEST]->[SENSOR TEST]-> [INK NEND1](The number meets the cartridge No.). 2. Check the peripheral and the assembly of the End Sensor. 3. Check the connection of the Presence Sensor and the Near End Sensor. 4. Replace the Cartridge with a new one 5. Replace the Presence/Near End Sensor with a new one. 6. Replace the SL-Relay PCB with a new one. 7. Replace the Main PCB with a new one.

Code: 602
Display: ERROR 602 INK END
Description: Ink end (No ink left)
Remedy: (If this message appears when a new cartridge or a cartridge with enough ink is set) 1. Execute and confirm [#TEST]->[SENSOR TEST]-> [INK NEND1](The number meets the cartridge No.). 2. Check the peripheral and the assembly of the End Sensor. 3. Check the connection of the Presence Sensor and the End Sensor. 4. Replace the Cartridge with a new one. 5. Replace the Presence / Near End Sensor with a new one. 6. Replace the SL-Relay PCB with a new one. 7. Replace the Main PCB with a new one.

Code: 603
Display: ERROR 603 NO CARTRDG
Description: No cartridge (Cartridge is not installed)
Remedy: (When the message is still displayed even after a Ink Cartridge is charged;) 1. Execute and confirm [#TEST]->[SENSOR TEST]-> [INK1](The number meets the cartridge No.).. 2. Check the peripheral and the assembly of the Presence Sensor. 3. Check the connection of the Presence Sensor and the End Sensor 4. .Replace the Cartridge with a new one 5. Replace the Presence/Near End Sensor with a new one. 6. Replace the SL-Relay PCB with a new one. 7. Replace the Main PCB with a new one. (Refer to 3.3.

Code: 605
Display: ERROR 605 !CLEANING WIPER
Description: Wiper lifetime (Wiping times exceeding the specified number.) 1),Wiping times (Ink parameter 1 No45 WipeCnt) Wiping time is cleared when the following is executed: [FUNCTION MAINTENANCE]- >[STATION]->[MENT:WIPER EXCHG] 2),Specified number :Wiper life (Ink parameter 2 No58 WIPElmt) x Wiper replacement level
Remedy: 1. Execute [FUNCTION MAINTENANCE]- >[STATION]->[MENT:WIPER CLEANING] to clean the wiper. 2. Replace the Main PCB with a new one.

Code: 606
Display: ERROR 606 WRONG CARTRIDGE
Description: The IC chip of the ink cartridge is not read properly.
Remedy: (If this message appears when a correct cartridge is set) 1. Check the assembly of the ID Contact PCB and the shape of the contact plate, and execute the cleaning. 2. Check the connection of the ID Contact PCB. 3. Replace the Cartridge with a new one 4. Replace the ID Contact PCB Assy. with a new one. 5. Replace the SL-

Источник

Проблемы, при которых на дисплее появляются сообщения об ошибке

Если в работе устройства возникают проблемы, то раздается звуковой сигнал, и на дисплее появляется соответствующее сообщение об ошибке.

Выполните необходимые корректирующие действия в соответствии с сообщением на дисплее.

Ошибки, сопровождающиеся предупредительными сигналами

Эти ошибки обычно имеют отношение к элементам устройства, которые связаны с чернилами.

Сообщения об ошибках

В сообщениях об ошибках указан номер ошибки. Если на дисплее появилось какое-либо сообщение об ошибке, отключите питание устройства и затем через некоторое время включите его снова. Если на дисплее вновь появится такое же сообщение, свяжитесь с местным дистрибьютором MIMAKI или обратитесь за помощью непосредственно в сервисную службу компании MIMAKI.

Сообщение об ошибке

Отключите на некоторое время питание устройство, затем включите его снова. При появлении на дисплее того же сообщения, обратитесь к местному дистрибьютору за сервисной помощью.

Приложение

В приложении описаны спецификации и детали устройства, а также структура меню функций.

Содержание

Приложение

ОСНОВНЫЕ спецификации

СПЕЦИФИКАЦИИ ЧЕРНИЛ

РАЗМЕЩЕНИЕ предупредительных НАДПИСЕЙ

Структура меню функций……………………………………………………..

ОСНОВНЫЕ спецификации

Наименование	JV3-160SP
Печатающая головка	Метод	Пьезоэлектрическая печатающая головка «c каплей по запросу»
Спецификация	4 линейные головки
Дозатор	360 дозаторов для каждого цвета
Разрешение	360, 540, 720, 1440 точек на дюйм (т/д)
Режим печати	Набор из 4-х цветов	360 x 360 т/д: 1 / 2 / 4 проходов, в одном/ двух направлениях
360 x 720 т/д: 2 / 4 / 8 проходов, в одном/ двух направлениях
720 x 720 т/д: 2 / 4 / 8 проходов, в одном/ двух направлениях
720 x 1440 т/д: 4 / 8 / 16 проходов, в одном/ двух направлениях
1440 x 1440 т/д: 8 / 16 проходов, в одном/ двух направлениях
Набор из 6-х цветов	360 x 360 т/д: 2 / 4 / 8 проходов, в одном/ двух направлениях
360 x 540 т/д: 3 / 6 / 12 проходов, в одном/ двух направлениях
360 x 720 т/д: 4 / 8 / 16 проходов, в одном/ двух направлениях
720 x 720 т/д: 4 / 8 / 16 проходов, в одном/ двух направлениях
720 x 1440 т/д: 8 / 16 / 32 проходов, в одном/ двух направлениях
1440 x 1440 т/д: 16 / 32 проходов, в одном/ двух направлениях
Используемые чернила	Набор из 4-х цветов	4 цвета (черный, циан, маджента, желтый) по два цвета на 1 картридж для каждого цвета
Набор из 6-х цветов	6 цветов сольвентных чернил (черный, циан, маджента, желтый, светлый циан, светлая маджента), по одному каждого цвета, и 2 картриджа очистительной жидкости для 1 картриджа каждого цвета
Емкость чернильного картриджа	4-цветный набор: каждый цвет (220 cc  5 cc для каждого картриджа) x 2 6-цветный набор: каждый цвет (220 cc  5 cc для каждого картриджа) x 1 Около 200 cc для каждого картриджа, изменяемая
Тип материала для печати	Баннер, FF, ПВХ
Макс. ширина печати		1440 x 1440 т/д: 1610 мм (для 4 цветов), 1000 мм (для 6 цветов)
При нормальном сканировании	1610 мм
Высокоскоростное сканирование	1570 мм
Размеры рулонного материала	(макс.)	1620 мм
(мин.)	210 мм
	толщина	1.0 мм или менее (< 1, 0 мм)
внешний диаметр рулона	 180 мм или менее (<  180 мм)
вес рулона	25 Кг или менее (<25 кг)
внутренний диаметр рулона	2 дюйма, 3 дюйма
поверхность печати	Лицом наружу
крепление конца рулона	используется легкая клеящаяся лента для облегчения снятия бумаги с сердечника
Размеры листового материала	(макс.)	1620 мм
(мин.)	210 мм
Поля	листовой материал	правый и левый край: 15 мм
спереди: 65 мм
сзади: 110 мм
Поля	рулонный материал	правый и левый край: 15 мм
спереди: 25 мм
сзади: 0 мм
Точность размера	абсолютная точка	Любая наибольшая из  0.3 мм или  0.3 % от назначенной
воспроизводимость	Любая наибольшая из of  0.2 мм или  0.1 % от назначенной
Перпендикулярный	 0.5 мм / 1000 мм
Отклонение материала	5 мм или меньше / 10 м изменяемая (< 5 мм / 10 м)
Регулировка высоты головки	2.0 мм / 3 мм изменяемая, от поверхности рабочего печатного стола
Обрезка материала	Обрезка по оси Y при помощи резака на блоке головок, точность отрезания (шаги): 0.5 мм или менее.
Подача материала	Стандартное подающее устройство (закрутка внутрь / наружу, на выбор)
Емкость для отхода чернил	Бутылочный тип (2,000 cc [1pcs.]) Необходимость замены определяется визуально.
Интерфейс	Совместим с IEEE1394 и с IEEE1284.
Команда	MRL-II (база ESC/PV.2, MIMAKI)
Рабочий шум	в режиме ожидания: менее 58 dB (FAST-A, измерено на расстоянии 1 м со всех сторон) при непрерывной печати: менее 65 dB при прерывании печати: менее 70 dB
Стандарт безопасности	UL, VCCI-classA, FCC-classA, CEmarking, CBreport
Питание	AC 100 — 120 V± 10%, AC 220 — 240 V± 10%, 50/60 Hz ± 1 Hz
Поглощение энергии	1.5 KVA или менее
рекомендованные условия окружающей среды	допустимая температура	От 20º С до 35º C
влажность	35 to 65 % относительной влажности (без конденсации)
гарантированная температура	От 20º С до 25º C
колебания температуры	± 10 º C / в час или менее
пыль	Условия обычного офисного уровня
Вес	основной блок	185 кг (без переднего вытяжного блока: 175 кг или менее)
габариты	ширина	2660 мм
глубина	Менее 750 мм
высота	Менее 1240 мм

СПЕЦИФИКАЦИИ ЧЕРНИЛ

Наименование	Спецификация
Цвет	Картридж с чернилами черного цвета
Картридж с чернилами цвета циан
Картридж с чернилами цвета маджента
Картридж с чернилами желтого цвета
Картридж с чернилами цвета светлый циан
Картридж с чернилами цвета светлая маджента
емкость картриджа с чернилами	220 cc для каждого картриджа
срок хранения	Один год с даты производства (при комнатной температуре)
В течение 3 месяцев после открытия упаковки
t хранения	-30 to 40º C (Хранение при t = 40ºC не более месяца) -30 to 60ºC (Хранение при t = 60ºC не более 120 часов, а при t = 40ºC — не более одного месяца)

РАЗМЕЩЕНИЕ предупредительныХ НАДПИСЕЙ

На устройстве приклеены этикетки с предупредительными надписями. Убедитесь в том, что Вы правильно понимаете все, что на них написано. Если хотя бы одна из надписей загрязнится до такой степени, что понять написанное будет невозможно, или если надпись отклеится, приобретите новую у своего местного дистрибьютора или в офисе MIMAKI.
Лицевая сторона

З
адняя сторона

Структура меню функций

Источник

You are here: Home / error code / Mimaki UJF605CII Error Codes and quick guides [Solved]

Fixing Mimaki UJF605CII Error Codes list

– Compatible Printer model: Mimaki UJF605CII
– Mimaki UJF605CII Error Code description:

Code: 01
Display: ERROR 01 MAIN ROM
Description: • The control ROM is in abnormal conditions.
Troubleshooting Guides: 1) Replace the main PCB with a new one.

Code: 02
Display: ERROR 02 MAIN RAM
Description: • The control RAM is in abnormal conditions.
Troubleshooting Guides: 1) Replace the main PCB with a new one.

Code: 03
Display: ERROR 03 POWER +5V POWER +35V
Description: • The +5V (+35V) voltage is in abnormal conditions.
Troubleshooting Guides: 1) Replace the power supply or the main PCB with a new one.

Code: 04
Display: ERROR 04 FLASH SAVE
Description: • The Flash memory is in abnormal conditions.
Troubleshooting Guides: 1) Replace the main PCB with a new one.

Code: 05
Display: ERROR 05 FPGA ss
Description: • FPGA configuration error
Troubleshooting Guides: 1) Replace the main PCB with a new one.

Code: 06
Display: ERROR 06 UHC 01 nnnn
Description: Band memory configured incorrectly. n=UHC No.1-8
Troubleshooting Guides: 1) Check that UHCII PCB is inserted securely in the main PCB. 2) Turn ON/OFF the plotter and check the problem disappears. 3) Upgrade the firmware.

Code: 06
Display: ERROR 06 UHC 02 nnnn
Description: . UHC status ready turned OFF. n=UHC No.1-8
Troubleshooting Guides: 1) Check that UHCII PCB is inserted securely in the main PCB. 2) Turn ON/OFF the plotter and check the problem disappears. 3) Upgrade the firmware.

Code: 06
Display: ERROR 06 UHC 03 nnnn
Description: . Waiting for UHC bus busy cancellation. 5sec timeout. n=UHC No.1-8
Troubleshooting Guides: 1) Check that UHCII PCB is inserted securely in the main PCB. 2) Turn ON/OFF the plotter and check the problem disappears. 3) Upgrade the firmware.

Code: 06
Display: ERROR 06 UHC 04 nnnn
Description: . Waiting for UHC status Read. 5sec timeout. n=UHC No.1-8
Troubleshooting Guides: 1) Check that UHCII PCB is inserted securely in the main PCB. 2) Turn ON/OFF the plotter and check the problem disappears. 3) Upgrade the firmware.

Code: 06
Display: ERROR 06 UHC 05 nnnn
Description: . Waiting for UHC response. 5sec timeout. n=UHC No.1-8.
Troubleshooting Guides: 1) Check that UHCII PCB is inserted securely in the main PCB. 2) Turn ON/OFF the plotter and check the problem disappears. 3) Upgrade the firmware.

Code: 06
Display: ERROR 06 UHC 06 nnnn
Description: . UHC status: Receiving FIFO full. Waiting for cancellation. 10sec timeout. n=UHC No.1-8
Troubleshooting Guides: 1) Check that UHCII PCB is inserted securely in the main PCB. 2) Turn ON/OFF the plotter and check the problem disappears. 3) Upgrade the firmware.

Code: 06
Display: ERROR 06 UHC 07 nnnn
Description: . UHC status: Waiting for band memory clear. 10msec timeout. n=UHC No.1-8
Troubleshooting Guides: 1) Check that UHCII PCB is inserted securely in the main PCB. 2) Turn ON/OFF the plotter and check the problem disappears. 3) Upgrade the firmware.

– Mimaki UJF605CII Error codes and solution steps to solve problems:

Code: 06
Display: ERROR 06 UHC 08 nnnn
Description: . UHC status: Waiting for head plotting area cancellation. 3sec timeout. n=UHC No.1-8
Troubleshooting Guides: 1) Check that UHCII PCB is inserted securely in the main PCB. 2) Turn ON/OFF the plotter and check the problem disappears. 3) Upgrade the firmware.

Code: 06
Display: ERROR 06 UHC 09 nnnn
Description: . UHC current coordinate setting trouble. n=UHC No.1-8
Troubleshooting Guides: 1) Check that UHCII PCB is inserted securely in the main PCB. 2) Turn ON/OFF the plotter and check the problem disappears. 3) Upgrade the firmware.

Code: 06
Display: ERROR 06 UHC 10 nnnn
Description: . Waiting for UHC plotting data write. 3sec timeout. n=UHC No.1-8
Troubleshooting Guides: 1) Check that UHCII PCB is inserted securely in the main PCB. 2) Turn ON/OFF the plotter and check the problem disappears. 3) Upgrade the firmware.

Code: 06
Display: ERROR 06 UHC 11 nnnn
Description: • Defective output of head voltage, or return of head voltage, A/D data is not available. n=UHC No.1 to 8
Troubleshooting Guides: 1) Check connector connection for MAINII board. 2) Check connector connection for UHCII board. 3) Check connector connection r for SLIDER-Relay board. 4) Check connector connection for SLIDER board 5) If 1 to 4 are not effective, replace one of the board.

Code: 07
Display: ERROR 07 DFC 01
Description: • Transfer size trouble. L1=F/W request size. L2=DFC transfer size.
Troubleshooting Guides: 1) Check that UHC PCB is inserted securely in the main PCB. 2) Turn power ON and OFF and check the problem disappears. 3) Upgrade the firmware.

Code: 07
Display: ERROR 07 DFC 02
Description: • Waiting for control command to be issued. 5sec timeout.
Troubleshooting Guides: 1) Check that UHC PCB is inserted securely in the main PCB. 2) Turn power ON and OFF and check the problem disappears. 3) Upgrade the firmware.

Code: 10
Display: ERROR 10 COMMAND
Description: • Command code other than MRL has been received.
Troubleshooting Guides: 1) Check connection of 1394 board or replace the board.

Code: 11
Display: ERROR 11 PARAMETER
Description: • Parameter that has not defined in MRL has been received.
Troubleshooting Guides: 1) Check the connection or replace IEEE1394 PCB.

Code: 12
Display: ERROR 12 OFF SCALE
Description: • Effective plotting range has been exceeded.
Troubleshooting Guides: 1) Set the plotting range to the plotter specification.

Code: 13
Display: ERROR 13 MEMORY DATA
Description: • For memory mode, each mechanical has different resolution or the same color has been specified for different mechanical.
Troubleshooting Guides: 1) Make sure that each mechanical has the same resolution or the same color has not been specified for different mechanical.

Code: 20
Display: ERROR 20 I/F BOARD
Description: • A error occurred in communication between the main PCB and the interface board.
Troubleshooting Guides: 1) Replace the I/F PCB with a new one. 2) Replace the main PCB with a new one.

Code: 23
Display: ERROR 23 HOST I/F
Description: • A time limit exceeded error occurred in communication between the host computer and the interface board.
Troubleshooting Guides: 1) Is the cable loose? 2) Has an error occurred on the host computer? 3) Is the application being used running normally?

Code: 24
Display: ERROR 24 I/F INITIAL
Description: • The I/F board is in abnormal conditions.
Troubleshooting Guides: 1) Replace the I/F PCBwith a new one. 2) Replace the main PCB with a new one. 3) Replace the I/F connection board with a new one.

Code: 30
Display: ERROR 30 OPERATION
Description: • Improper operation has been performed.
Troubleshooting Guides: 1) Indicate the improper operation.

Code: 34
Display: ERROR 34 DATA REMAIN
Description: • Operating condition is tried to be changed when data that has not yet been plotted remains.
Troubleshooting Guides: 1) Explain that any of the operating conditions cannot be changed if data that have not been plotted remains.

Code: 35
Display: ERROR 35 MARK DETECT
Description: • Register marks detection failed.
Troubleshooting Guides: 1) Re-detect register marks. If this fails again, execute “Paper Sensor” under “#TEST” and check the register mark sensors. If necessary, replace the register mark sensors.

Code: 36
Display: ERROR 36 HEAD GAP
Description: • Head gap is too small.
Troubleshooting Guides: 1) Turn on the power. 2) Adjust the area sensor. 3) Replace the area sensor

Code: 40
Display: ERROR 40 MOTOR X
Description: • The X-axis motor has been overloaded.
Troubleshooting Guides: 1) Turn on the power. 2) Replace X axis motor. 3) Replace a main PCB.

Code: 41
Display: ERROR 41 MOTOR Y
Description: • The Y-axis motor has been overloaded. • The brush of motor is in abnormal conditions.
Troubleshooting Guides: 1) Turn on the power. 2) Replace Y axis motor. 3) Replace a main PCB.

Code: 42
Display: ERROR 42 X CURRENT
Description: • Overcurrent error has arisen on the X-axis motor .
Troubleshooting Guides: 1) Turn on the power. 2) Replace X axis motor. 3) Replace a main PCB.

Code: 43
Display: ERROR 43 Y CURRENT
Description: • The slider is stopped with an obstacle. • Overcurrent error has arisen on the Y-axis motor
Troubleshooting Guides: 1) Remove the obstacle. 2) Turn on the power. 3) Replace Y axis motor. 4) Replace a main PCB.

Code: 44
Display: ERROR 44 SCAN RANGE
Description: • Out-of-range scan was attempted.
Troubleshooting Guides: 1) Report the problem to Development Division. Upgrade the firmware later.

Code: 50
Display: ERROR 50 X ORIGIN
Description: • X-axis origin detection has not been successfully carried out.
Troubleshooting Guides: 1) Replace a X origin sensor. 2) Replace a X axis motor.

Code: 51
Display: ERROR 51 Y ORIGIN
Description: • Y-axis origin detection has not been successfully carried out.
Troubleshooting Guides: 1) Replace a Y axis motor. 2) Replace a Y origin sensor. 3) Replace a IO PCB. 4) Replace a main PCB.

Code: 53
Display: ERROR 53 STEP ORIGIN
Description: • Capping or wiping origin detection failed.
Troubleshooting Guides: 1) Check and correct the capping or wiping mechanism. 2) Replace the capping or wiping origin sensor.

Code: 60
Display: ERROR 60 FLASHING nnnn
Description: . Flashing timeout. n=UHC No.1-8
Troubleshooting Guides: 1) Replace the slider board. 2) Replace the head FPC cable.

Code: 61
Display: ERROR 61 TEMP ss nnnnnnnn
Description: . Head control temperature trouble. n=UHC No.1-8
Troubleshooting Guides: 1) Ink level is too low. Ambient temperature is too high (remove the cause). 2) Replace the slider board. 3) Replace the head FPC cable.

Code: 70
Display: ERROR 70 WATER LACK
Description: • Hot water tank level is too low.
Troubleshooting Guides: 1) Add water.

Code: 71
Display: ERROR 71 WATER DEVICE ss
Description: • ss=01: Hot water tank temperature control problem. • ss=02: Hot water tank line problem. • ss=03: Head temperature problem.
Troubleshooting Guides: 1) Replace the water heater. 2) Correct the hot water line. 3) Replace the head.

Code: 72
Display: ERROR 72 UV POWER OFF (Copper-iron and Inverter type power supply unit )
Description: • The breaker of UV device is off.
• The UV interface cable is not connected to the device.
Troubleshooting Guides: 1) Turn on the breaker of UV device.
1) The UV interface cable connects to the device.

Code: 72
Display: ERROR 72 UV POWER OFF (Inverter type power supply unit )
Description: • The radiator fan of UV irradiation device is defective.
• The UV lamp control cable is broken.
Troubleshooting Guides: 1) Replace the UV irradiation device. 1) Replace the UV lamp control cable.

Code: 73
Display: ERROR 73 UV DEVICE 01 ERROR 73 UV DEVICE 02
Description: • 01: The shutter is not opened. • 02: The shutter is not closed. • The shutter switch for open/ close is defective.
• UV lamp control cable has broken of the wire.
Troubleshooting Guides: 1) Replace the UV irradiation device with a new one.
1) Replace the UV lamp control cable with a new one.

Code: 73
Display: ERROR 73 UV DEVICE 01
ERROR 73 UV DEVICE 02
ERROR 73 UV DEVICE 04 (Shutter)
Description: • 01: The shutter is not opened. • 02: The shutter is not closed. • The shutter switch for open/ close is defective. • UV lamp control cable has broken of the wire.
Troubleshooting Guides: 1) Replace the UV irradiation device with a new one. 1) Replace the UV lamp control cable with a new one.

Code: 73
Display: ERROR 73 UV DEVICE 03 (Lamp.V20)
Description: • The UV lamp is tried to relight with burning. • UV lamp cable has not connected to the terminal block. • UV lamp have not been set. • UV lamp cable has broken down or the connector is defective.
Troubleshooting Guides: 1) Turn the lamp on after cooling down the UV lamp. 1) Make sure that the UV lamp cable have connected to the terminal block in the UV irradiation device. 2) Make sure to set the UV lamp 1) Replace the UV lamp cable with a new one.

Code: 73
Display: ERROR 73 UV DEVICE 03 (Lamp.Volt)
Description: • Voltage is abnormal conditions by the UV lamp anomaly. • Voltage increase or decrease.
Troubleshooting Guides: 1) Replace the UV lamp with a new one.

Code: 74
Display: ERROR 74 UV DEVICE
Description: • The UV lamp is tried to relight with burning. • UV lamp cable has not connected to the terminal block. • UV lamp have not been set. • UV lamp cable has broken down or the connector is defective. • Voltage is abnormal conditions by the UV lamp anomaly. • Voltage increase or decrease. • UV power supply internal parts are abnormal heating.
Troubleshooting Guides: 1) Turn the lamp on after cooling down the UV lamp. 1) Make sure that the UV lamp cable have connected to the terminal block in the UV irradiation device. 2) Make sure to set the UV lamp 1) Replace the UV lamp cable with a new one. 1) Replace the UV lamp with a new one. 1) Replace the UV power supply unit with a new one.

Code: 74
Display: ERROR 74 UV DEVICE (TEMP lamp is lighting)
Description: • Malfunction of UV irradiation device cooling fan. • UV lamp control cable has broken of the wire.
Troubleshooting Guides: 1) Replace the UV irradiation device with a new one. 1) Replace the UV lamp control cable with a new one

Code: 74
Display: ERROR 74 UV DEVICE (ERROR)
Description: • UV power supply internal parts are abnormal heating.
Troubleshooting Guides: 1) Make sure that the air filters in the front or the rear side is not covered with objects. 2) Make sure that the rear side fan of the UV power supply is running. 3) Replace the UV power supply unit with a new one.

Code: n01
Display: ! UV LAMP UV LAMP CHANGE :ent
Description: • Changing time for the UV lamp.
Troubleshooting Guides: 1) Replace the UV lamp with new one.

Code: n02
Display: ! UV LAMP UV LEVEL CHK :ent
Description: • The UV lamp level has exceeded the predetermined amounts of time.
Troubleshooting Guides: 1) Confirm the UV lamp light level.

Code: n03
Display: <<LOC.>>NEAR END COLOR :KCMYcmW
Description: • The amount of ink remaining in the ink cartridge is insufficient.
Troubleshooting Guides: 1) Printing can be continued in file-by-file basis by pressing the [REMOTE] key.

Code: n04
Display: ! INK END COLOR :KCMYcmW
Description: • There is no ink in ink cartridge.
Troubleshooting Guides: 1) Replace the ink cartridge of which color is shown on the LCD with a new one.

Code: n05
Display: INK CARTRIDGE COLOR :KCMYcmW
Description: • The ink cartridge is not installed to the ink station.
Troubleshooting Guides: 1) Install the ink cartridge(s) corresponding with the color shown on the display.

Code: n06
Display: ! CARTRIDGE CHECK COLOR :KCMYcmW
Description: Not operated as a menu.
Troubleshooting Guides: 1) Confirm the ink cartridge.

Code: n07
Display: ! INK TANK WASTE TANK FULL
Description: • Waste ink tank is full.
Troubleshooting Guides: 1) Remove the waste ink tank and set an empty waste ink tank.

Code: n08
Display: ! COVER OPEN CLOSE A COVER
Description: • The cover is open.
Troubleshooting Guides: 1) Close the cover.

Code: n09
Display: (COVER OPEN) PRESS <ENT> KEY
Description: • [ENTER] key check after closing the cover.
Troubleshooting Guides: 1) Press the [ENTER] key and restart the device.

Code: n10
Display: !MEDIA HEIGHT TABLE DOWN
Description: • The area sensor detected an obstacle while jog operation is being performed.
Troubleshooting Guides: 1) Down the table by pressing the [ ] key on the sub panel until the LCD indicates “OK”, and then start the jog operation again. Or remove the media from the table and then press the [ENTER] key.

Code: n11
Display: !MEDIA HEIGHT THICK. OF MEDIA
Description: • Area sensor detected the obstacle.
Troubleshooting Guides: 1) Confirm the thickness of the media and input the value again.

Code: n12
Display: !CAP SENSOR FAIL
Description: • If the cam rotates half from the bottom position of the capping, capping sensor cannot be detected.
Troubleshooting Guides: 1) Capping sensor may have an error. 2) Sensor position or adjustment of the lowest point position may be inadequate.

Code: n13
Display: !ORIGIN SETTING IS OUT OF RANGE
Description: • The origin has been set outside the printing area.
Troubleshooting Guides: 1) Set the origin inside the printing area.

Waste Ink Pad Counter Utility Functions:

– Cleaning printhead.
– Ink charge.
– Fix Epson red lights blinking Error

– Fix Epson Service Required Error: A printer’s ink pad at the end of its service life Please contact Epson Support.

– Check the current value of waste ink counters and ink level counters.
– Clear Waste Ink Counters.
– Read and write serial number.
– Read and write USB ID.
– Read and write HEAD ID.
– Make EEPROM dump, backup.
– Paper feed test.
– Nozzle check.
– Color check pattern.
– Initialize (disable) PF deterioration offset.
– Retrieve device information

Contact us to get support with Mimaki UJF605CII Error case

Telegram: https://t.me/hyperaktiv
Facebook: https://www.facebook.com/dngnm/

Источник

We’ve all been in the situation where your Mimaki displays an error code with a number and abbreviated error code but, what are they trying to tell us? See below for the most common error codes that appear on Mimaki JV33 & CJV30 printers.

All Mimaki parts available here on Solventinkjet.com!

Error 01 Main Rom — The main board may be failing. Turn off the printer, wait 15 minutes, and power back on. If the error persists, replace the main board.

Error 02 Main Ram — The main board may be failing. Turn off the printer, wait 15 minutes, and power back on. If the error persists, replace the main board.

Error 03 Power +6v, +24v, +42v — The power board is malfunctioning. Check the output power for each voltage and replace as needed.

Error 04 F-Rom — The main board may be failing. Reinstall your system parameters and try to boot. If the error persists, replace the main board.

Error 06 SD-Ram — The main board may be failing. Turn the power off for 15 minutes and then power back on. If the error persists, replace the main board and then PRAM board.

Error 07 Head, Voltage — There is a short in the head circuit. Check your head cables for damage, corrosion, ink splatter etc. and replace as necessary. If the error persists, replace the print head.

Error 08 Linear Encoder: Sensor, DIR., Count — The encoder strip and/or sensor is dirty or damaged. Clean the encoder strip with alcohol and air dust the sensor. If the error persists, replace the strip and then sensor in that order.

Error 36-C Mark Detect — The mark sensor did not detect the crop marks. Make sure the crop mark settings are setup properly. Clean the sensor with alcohol and then run the sensor sensitivity adjustment. If the error persists, replace the sensor.

Error 40 Motor Alarm X — The feed motor is under too much load. Make sure there is nothing jamming the grit roller or anything that might be keeping the motor from moving such as the media being at the end of the roll and still glued to the core.

Error 41 Motor Alarm Y — The motor that moves the head back and forth is under too much load. Make sure there is nothing jamming the head or anything that might be keeping the head from moving.

Error 42 X Over Current — The feed motor is requiring too much voltage to move. Make sure there is nothing jamming the grit roller or anything that might be keeping the motor from moving such as the media being at the end of the roll and still glued to the core. Replace the motor and then main board in that order if the error persists.

Error 43 Y Over Current — The motor that moves the head back and forth is requiring too much voltage. Make sure there is nothing jamming the head or anything that might be keeping the head from moving. Clean the encoder strip and air dust the sensor first. Replace the encoder strip, sensor, motor and then main board in that order if the error persists.

Error 46 Wiper — The wiper failed to return to the home position or the sensor has failed. Check for anything that may be preventing the wiper from sliding properly, then clean and grease the rail the wiper slides on. Clean the wiper sensor with air dust and alcohol. If the error persists, replace the wiper sensor, then maintenance board in that order.

Error 50 Media Detect — The printer failed to measure the material width. Make sure the media is loaded properly. Clean the media sensor with alcohol and air duster. Run the sensor adjustment. If the error persists, replace the sensor.

Error 120 Environment Temp (Low) — It’s too cold in your office.

Error 121 Environment Temp (Hi) — It’s too hot in your office.

Error 144 Cartridge Set! — One or more of your cartridges are not reading properly or are the incorrect ink type. Double check that the ink is the proper kind and color. If the error persists, buy new ink or get new chips from your supplier.

Error 170 Cutter Lock — The cut tool fails to lock in the home position. Change system parameter number 37 CLKAJST to 0, power the machine off by the main power switch in the back and then power back on. This will automatically adjust the lock position.

Error 170 Print Head Lock — The print head fails to lock at the home position. Make sure the hook on the right side of the head is intact. If the error persists, replace the head lock solenoid.

Error 181 PR Position — The pinch rollers are not properly set. Make sure each pinch roller is located over a grit roller. Arrows on the printer indicate the allowed pinch roller locations.

Error 200 Head Memory — The head memory is failing or unplugged. Make sure the head memory is connected properly. If the error persists, replace the head memory cable, then replace the head.

Error 202 Device Construction — Either the head you installed is not the proper head or the head itself is damaged. Reinstall the head cables to rule it out as a possibility. If the cables don’t fix it, it’s usually a bad head.

Источник

Ремонт мфу принтера MIMAKI UJF-6042

Принтер MIMAKI UJF-6042 обслуживание и ремонт в Москве и области.

Ремонт принтера MIMAKI UJF-6042

Сломался принтер MIMAKI UJF-6042?
Решение есть!

Услуги	Гарантия на работу	Стоимость (руб.)	Выполнение дней
Диагностика	—	бесплатно	1
Выезд мастера	—	бесплатно	1
Ремонт принтера	6 месяца	от 2000	1-5
Профилактика принтера	2 месяца	от 2000	1
Замена ремня каретки	2 месяца	от 2000	1-7
Замена ролика подачи бумаги	2 месяца	от 2000	1-7
Замена каретки	2 месяца	от 2000	1-7
Замена платы высоковольтной	2 месяца	от 2000	1-7
Замена или восстановление главной платы	2 месяца	от 2000	1-7
Замена низковольтной платы	2 месяца	от 2000	1-7
Замена печатающей головки	2 месяца	от 2000	1-7
Замена шлейфа печатающей головки	2 месяца	от 2000	1-7
Настройка принтера	2 месяца	от 2000	1-2
Калибровка печатающей головки	2 месяца	от 2000	1-2
Прошивка принтера	2 месяца	от 2000	1-2
Устранение программных сбоев	2 месяца	от 2000	1-7
Чистка печатающей головки картриджа	2 месяца	от 2000	1-7
Заправка картриджа	2 месяца	от 2000	1-2
Установка СНПЧ	2 месяца	от 2000	1-7

Часто случается, что принтер перестает работать должным образом и начинает плохо печатать, или вообще не печатать. Что же делать в данном случае?

Вам нужна помощь профессионального мастера, со знанием своего дела, который проведет диагностику и ремонт принтера MIMAKI UJF-6042.
Наш технический центр занимается как раз такими поломками. Мы сделаем ваш принтер MIMAKI UJF-6042 рабочим в максимально короткие сроки. Просто наберите и свяжитесь с нами!
Обслуживание принтера MIMAKI UJF-6042
Порядок диагностики и ремонта принтера MIMAKI UJF-6042
Обслуживание принтера mimaki включает замену только качественных запчастей от производителя.

Частые неисправности и ошибки принтеров MIMAKI UJF-6042:

что делать если принтер не отвечает
принтер печатает с полосами
документ в очереди, а принтер не печатает
принтер заминает бумагу
что делать если принтер не захватывает бумагу
принтер печатает пустые листы
после заправки картриджа принтер не печатает
компьютер не видит принтер
почему не печатает принтер хотя краска есть
принтер печатает пустые листы
почему принтер печатает белые листы
что делать если бумага застряла в принтере
принтер не берет бумагу из лотка
почему принтер печатает чёрные листы
при печати принтер пачкает бумагу
или другие ошибки принтера mimaki

Диагностика мфу MIMAKI UJF-6042 бесплатно

Мы проводим работу по выявлению поломок вашего принтера, внимательно рассматривая все блоки, детали, узлы аппаратов на наличие дефектов, а также определяем объемы работ, необходимые для ремонта принтера, в процессе которой может потребоваться и повторная диагностика.
Важно! Мы можем предоставить Вам бесплатную удаленную диагностику по телефону. Все необходимые действия вы выполняете по рекомендациям нашего мастера.
Или после звонка, к вам выезжает наш специалист и проводит диагностику принтера. Он выявляет причину, по которой принтер неисправен. Он определяет запчасти, которые требуют замены, выставляет счет на нужные детали и после оплаты выставленного счета, выполняет ремонт и замену нужных запчастей принтера.
Можно ли обойтись без диагностики?
Конечно же, нет. Без диагностики невозможен любой ремонт любой техники. А наши мастера, знающие свое дело, могут установить причину поломки в максимально короткие сроки как у нас, так и по месту эксплуатации, что позволяет сэкономить ваше и наше время.
Что если поломка появится снова?
Наши специалисты являются профессионалами, и после их работы у Вас навряд ли что-либо опять сломается. Но все же, если так получилось, то мы готовы предоставить Вам гарантию от нашего сервисного центра, а также на замененные запчасти от производителя.
Принтер может сломаться по многим причинам, вот одни из них: загрязненные узлы аппаратов принтера, неработоспособность картриджей, неработоспособности печатающих головок, неправильная работа тракта прохождения бумаги, неправильная работа узла очистки головок, поломка в результате установки СНПЧ, неправильная парковка каретки.
Мы ремонтируем MIMAKI UJF-6042 и другие принтеры.

Источник

Error Codes List page 15

Проблемы, при которых на дисплее появляются сообщения об ошибке

Ошибки, сопровождающиеся предупредительными сигналами

<img decoding="async" onError="javascript: wp_broken_images = window.wp_broken_images || function(){}; wp_broken_images(this);" src="https://rykovodstvo.ru/pars_docs/refs/18/17136/17136_html_m26d88f93.gif" />

<img decoding="async" onError="javascript: wp_broken_images = window.wp_broken_images || function(){}; wp_broken_images(this);" src="https://rykovodstvo.ru/pars_docs/refs/18/17136/17136_html_5ecacabd.gif" />

Сообщения об ошибках

Приложение

ОСНОВНЫЕ спецификации

СПЕЦИФИКАЦИИ ЧЕРНИЛ

РАЗМЕЩЕНИЕ предупредительныХ НАДПИСЕЙ

Структура меню функций

Fixing Mimaki UJF605CII Error Codes list

Waste Ink Pad Counter Utility Functions:

Contact us to get support with Mimaki UJF605CII Error case

Частые неисправности и ошибки принтеров MIMAKI UJF-6042:

Диагностика мфу MIMAKI UJF-6042 бесплатно