Error 81
- Make sure your printer is connected to MakerBot Print.
- Select your printer from the printer list.
- Select Utilties
- Select Calibration
- Select Calibrate Z Offset
1. Make sure your printer is connected to MakerBot Print.
…
If you find the spool is tangled:
- Pause the print and unload the filament from the extruder and untangle the spool.
- Cut a clean, flat edge on the end of the filament.
- Load the filament.
- Resume the print.
Full
Answer
What should I do if my Makerbot z18 is not printing?
Open your extruder or printer at your own risk. We’ve found in most cases the error in question is caused by the smart extruder on the Makerbot z18, 5th Generation Replicator and the Mini, so always try changing extruders and restart the printer before calling support.
Next, if you continue to get Error 81, t is possible that your printer is registering slipping when there is none. To see if that is the case, on your printer, navigate to Settings > Notifications > Filament Error Detection and turn it off. Try a print.
What does error 72 mean on MakerBot extruder?
Message: EXTRUDER ERROR Oops, we have a problem with your Smart Extruder (Error 72: Tool Fan Open), Please visit our support page at Makerbot.com/support. What does it mean: There is a problem with the extruder fan, located on the machine (not the smart extruder)
How to fix MakerBot smart extrusion problems?
How to fix it: The issue is the circuit board in the carriage (the black box with the fan, stepper motor and mounting for the smart extruder that rides on the rail). MakerBot won’t ship just the board, You have to buy the whole carriage assembly (board, stepper motor, fan, and housing which they will ship to for you to replace).
How do you fix a filament slip?
0:141:03Makerbot Filament Slipping? Fixed mine for FREE! — YouTubeYouTubeStart of suggested clipEnd of suggested clipBecause it keeps saying I had filament slipping errors I solved my issue by going to settings. AndMoreBecause it keeps saying I had filament slipping errors I solved my issue by going to settings. And then choosing notifications.
How do you fix the filament jam on a MakerBot Replicator?
1:445:02Jammed/Clogged Makerbot Smart Extruder+ Plus Teardown and FixYouTubeStart of suggested clipEnd of suggested clipAnd you’ll start to see where the jam is and now when you open this piece. Up. You’ll see a piece ofMoreAnd you’ll start to see where the jam is and now when you open this piece. Up. You’ll see a piece of filaments sticking out and you can just grab this and pull it out and that’s it.
What does filament slip mean?
Answer. A Filament Slip notifies you that there is something preventing filament from extruding at the rate that it is meant to be. There can be a few different causes for this notification. By nature, the Replicator Mini+ will try to recover from the Filament Slip automatically and continue printing.
Why did MakerBot fail?
This was partly due to the poor reputation of the Smart Extruder on the 5th generation machines. Estimates for the mean time before failure for the MakerBot Smart Extruder were between 300 and 500 hours. Jonathon Jaglom, CEO of MakerBot, has said «86% of all failures of 5th gen MakerBots were with the extruder.»
How do you unclog a MakerBot replicator?
Unclogging Procedures Unload any filament from the extruder. Turn off your MakerBot Replicator 2. Loosen the two bolts on the front of the extruder, unplug the motor cable, and pull the motor out from the back of the extruder. Set the motor aside.
How do you unclog a MakerBot extruder?
Let’s Get StartedRemove the acrylic panel(s), set them aside.Remove the filament guide tube. … Remove the loaded filament. … Make sure the nozzle is still heated to 215°C. … Loosen the nozzle. … Allow the nozzle to cool. … Check to see if the nozzle is clogged. … Look down the barrel of the smart extruder.
Why is extruder clicking?
Filament grinding, which is accompanied by a “clicking” or «squeaking » sound coming from the extruder, usually happens when the extruder gears are unable to push the filament further towards the nozzle. Over time, the gears grind away the filament, until they can’t grab it anymore.
What temperature should I print PLA at?
PLA prints at a relatively low temperature, typically printing between 190°C — 220°C. The optimal printing temperature of a PLA filament will vary depending on which printer you are using and more importantly will vary between filament brands.
Why is my 3D printer making a clicking noise?
A 3D printer can make a clicking noise for various reasons, such as jammed filament, a damaged feeder motor, or if the nozzle is blocked. Most of these problems can be fixed at home by adjusting the printer’s settings and ensuring that all the parts are cleaned, secured, and operating accordingly.
Is MakerBot dead?
MakerBot is not dead, but it is connected to life support waiting for a merciful soul to pull the plug. This week, MakerBot announced it would lay off its entire manufacturing force, outsourcing the manufacturing of all MakerBot printers to China.
Is MakerBot still in business?
MakerBot eventually was bought by Stratasys and the company has continued to nurture the business. The Cube went away around 2015. And 3D printing went back to normal because, after all, it is still a pretty magical business that is transforming manufacturing.
Is a MakerBot worth it?
The MakerBot Replicator Desktop 3D Printer stands out for its ease of setup, smooth operation, above-average print quality, user-friendly software, and multiple connectivity choices. It’s the best high-end 3D printer we’ve tested.
Is the MakerBot Replicator worth it?
Bottom Line Historically, MakerBot has made 3D printing easier and more accessible to new users. That said, the 5th Generation Replicator is an average printer at best, and grossly overpriced at worst. MakerBot’s Replicator is among the top well-known 3D printers on the market.
Is MakerBot opensource?
The original Makerbot printers were born from RepRap, an open source project that allowed anyone to build on and tinker with a 3D printing platform. Eventually, Makerbot decided to close the hardware doors to make something that anyone could use.
How long is Makerbot warranty?
Makerbot does have a 90-day warranty on all smart extruders purchased from them or an authorized reseller, so if it’s the extruder and it’s no more than 90-days from purchase, they will replace at no charge and they won’t charge a service fee for this.
Can I register my Z18 printer after warranty runs out?
It appears that even after your warranty runs out, you can register any 5th Gen, Mini, or z18 for MakerCare. At least at this time, you could buy a used z18 printer from eBay for almost half price, register it under your name on MakerBot’s website, then call and get Makercare.
What is Van -81?
When players encounter the Van -81 error, they receive the following message:
How to fix Error Code Van -81
According to the Valorant support pages, the first thing to try is the classic system restart. Restart your PC, and then restart the Riot Client. If this is unsuccessful, then the recommendation is to uninstall both Riot Vanguard and Valorant, and reinstall both.
By Steven Shaw
Stealth Optional is supported by its audience. When you purchase through links on our site, we may earn an affiliate commission. Learn more
Popular Posts:
Here is how I fixed it.
(Error 81 due to a false positive filament jam — occurs because the encoder wheel gets stuck and isn’t turned by the moving filament)
The problem was indeed the encoder wheel getting stuck which triggered a false error.
Your instructions do discuss the encoder wheel here. They say to move the encoder wheel to the «back side.» This was confusing to me for a few reasons:
— I didn’t know which side was the back side
— I didn’t know why this would help
— The wheel didn’t seem to move when I nudged it anyway.
If this is indeed the right fix for some people, can I suggest that the instructions give a little more detail? Like:
— Check if the wheel groove is not aligned with the top plastic hole. If necessary to fix the alignment, use a flat head screwdriver or a similar tool to gently push the wheel closer to the back side of the Smart Extruder.
_The real problem_
For me, the real problem was that the wheel didn’t turn because there was a combination of too much wheel axle friction (between the wheel and its axle) and/or not enough wheel groove friction (between the wheel groove and the plastic filament)
_Verifying this problem_
While the printing is in progress, shine a light through the top or right side of the 3D printer case. You can watch the encoder wheel. It should turn in sync with the filament passing through the wheel groove.
If there is an error, you can verify that the error happens because the encoder wheel stopped turning while the filament was flowing. This was happening for me in one particular sticky part of the encoder wheel’s rotation.
_The solution_
1: I applied lubricant to the encoder wheel axle.
— I didn’t even need to take the cartridge apart, I just used a needle to carefully apply some to the axle and manually turned the wheel while letting it drip down into the bearing.
2: I roughed the plastic of the encoder wheel groove.
— I used an exacto knife to make tiny scrapes all around both sides of the inside groove of the wheel.
3: Test that these steps are working by holding the (cooled down) extruder in your hand, and manually inserting a small length of plastic into the top hole. Move the filament in and out and ensure that the wheel is turning smoothly in sync with the filament passing through the wheel groove inside the cartridge.
I hope this helps others! I know it’s a very old product now, but maybe there’s still some people out there still having this problem. Good luck :thumbs-up:
These errors and solutions are compiled from many websites and forums around the Internet. We are not an authorized MakerBot repair center or dealer. Please DO NOT contact us asking for step-by-step instructions on how to fix. We don’t have those. We offer no guarantee the “fix” listed below will work and take no responsibility for any damage you may cause to your machine or extruder trying to repair it, since we did not write most of these. Open your extruder or printer at your own risk.
We’ve found in most cases the error in question is caused by the smart extruder on the Makerbot z18, 5th Generation Replicator and the Mini, so always try changing extruders and restart the printer before calling support. (They’re the first two things support will ask you to do, so it saves a couple of steps with them).
If you experience an error that’s not on this page and want to share, please email: jeff@3dprintrva.com. If we all share, we can all reduce the $100 service calls for simple fixes.
Extruder Warranty
Makerbot does have a 90-day warranty on all smart extruders purchased from them or an authorized reseller, so if it’s the extruder and it’s no more than 90-days from purchase, they will replace at no charge and they won’t charge a service fee for this.
Note: the SmartExtruders sold on eBay, included with used printers, Craig’s List and similar sites are not covered by warranty because 1) they are not being purchased from an authorized reseller and 2)more than likely the 90-day warranty expired before the seller listed it on eBay. (Before you “hate” on MakerBot for this policy, most manufacturers don’t offer warranty support these kind of purchases either).
MakerCare Warranty
This is a paid extended warranty service issued by MakerBot. You get unlimited free support calls until your extended warranty period runs out. You get a special phone number and extra support hours (including Saturdays). It may seem pricy, but if there is a hardware issue that does not involve the extruder they’ll cover it.
In helping a friend with a support issue, we called MakerBot and they offered us Makercare on a z18 printer that is over a year out of warranty. It appears that even after your warranty runs out, you can register any 5th Gen, Mini, or z18 for MakerCare. At least at this time, you could buy a used z18 printer from eBay for almost half price, register it under your name on MakerBot’s website, then call and get Makercare. You’d still come out ahead on total costs (compared to purchasing new) AND be covered for any hardware issues. If you find MakerBot is no longer doing this, let us know and we’ll remove.
Homing error
Message : There a few different “Homing Error” messages
What does it mean: Homing errors relate to the abiltly to find the build plate level.
How to fix it: In most cases the “bounce” ability of the nozzle is jammed and just needs wiggling to fix. If wiggling the nozzle doesn’t help, try restarting the printer.
Note: If you have just taken apart your extruder to clear a broken piece of filament, you may have pinched a wire leading to the hot end which will prevent the nozzle from moving.
Error 15:
Message:
What does it mean: There is a loose jumper cable on the z18 board. Apparently this happens due to the printer getting jarred during shipping. The “refurbished” models purchased on eBay and other sites have a higher rate of loose jumper cables.
How to fix: You must turn off & unplug your printer, remove the lower right back panel and make sure all jumper cables are seated in their connectors on the circuit board. Make sure you don’t touch any of the other components on the circuit board or you’ll have a very large paperweight!
Error 55 Heat watch dog error
Message: ??
What does it mean: This error relates to the readings on the temperature sensor. The machine thinks it is so hot it shut down for safety.
How to fix it: The only case we saw of this required returning to Makerbot for repair
Error 61 filament feeding error
Message : ??
What does it mean: That the castle head screw (also known as a Hob Bolt) can not /Is not spinning. Meaning the filament can not be driven down into the extruder. This may be because of a spool jam that is restricting the flow of filament to the extruder or because filament has broken within the extruder blocking the filament path. This is usually at only 4-5 cm down into the extruder.
How to fix it: Check the filament spool is not jammed and can spin freely and that the filament has not knotted. You extruder may need to be repaired.
Error 65 Thermocoupler Communication
Message: Oops we have a problem with your smart extruder (Error 65 : Thermocoupler Communication failure). Please disconnect and re-connect your smart extruder.
What does it mean: The machine thinks the connectors to the thermocoupler are not connected.
How to fix it: This error is usually the result of a connection issue between the smart extruder and the Smart Extruder carriage. Pull off the smart extruder. Clean pins and re-connect it. In most cases it is actually that the smart extruder is not connected properly or has dirty connectors. Press down the pins on the smart extruder a few times to make sure they have not gotten bent, damaged or stuck.
If the message is occurring mid print make sure the spool is not getting stuck and pulling the smart extruder off slightly.
Finally, take a look at the white ribbon cable that runs from the Smart extruder carriage to the back right of the machine. Are there any damaged points? If so (and the above did not stop the problem) please log a ticket with a photo. Also check that the cable has not become loose at either end.
Error 71
Message: Heater Open.
What does it mean: The machine can not heat the hot end or can not receive temperature information from the hot end.
How to fix it: Check POGO pins on extruder. Push in and out to see if any are sticking. In one case, we discovered that a wire between the extruder circuit board and the hot end was broken. If everything looks fine, replace smart extruder.
Error 72
Message: EXTRUDER ERROR Oops, we have a problem with your Smart Extruder (Error 72: Tool Fan Open), Please visit our support page at Makerbot.com/support.
What does it mean: There is a problem with the extruder fan, located on the machine (not the smart extruder)
How to fix it: Open a support ticket.
Error 1010:
Message: ??
What does it mean: There is a loose jumper cable on the z18 board. Apparently this happens due to the printer getting jarred during shipping. The “refurbished” models purchased on eBay and other sites have a higher rate of loose jumper cables.
How to fix: You must turn off & unplug your printer, remove the lower right back panel and make sure all jumper cables are seated in their connectors on the circuit board. Make sure you don’t touch any of the other components on the circuit board or you’ll have a very large paperweight!
Error 1013
Message : Homing timed out…
What does it mean: The machine has not been able to complete the homing routine because it is not getting feedback from its sensor/s
How to fix it: In most cases it just goes away when you restart. If it is a repeated problem the level sensor may be faulty and the extruder needs to be replaced.
Error 1024
Message: Your smart extruder is not connected…
What does it mean: The machine does not think that the smart extruder is connected
How to fix it: Check the extruder is actually attached flush to the machine. The castle nuts can sometimes mis align. Many cases of this error (at the attachment of the extruder or on load) are because either the extruder was not connected perfectly or that there is oil or similar on the connectors. Take off the extruder and clean the connectors to be sure this is not the case.
Where it occurs mid print – Make sure the filament is not pulling the extruder off the machine. If this issue happens a lot, check out Thingiverse for clips that will clamp the smart extruder to the carriage.
If this is not the case, we have seen some smart extruders are just faulty in this regard. Open a ticket.
No Error Code, But Filament Won’t Feed Through Cleared Extruder
Message: None.
Symptoms: I’ve seen a case with a z18 where the stepper motor is clicking and filament isn’t loading. Changing out extruders doesn’t help. Everything appears to be working properly, except filament won’t feed into extruder. If you are holding the filament as you load it into the extruder, you will feel resistance as the filament comes in contact with the shaft attached to the stepper motor. Can hear a clicking noise on filament load without filament in extruder.
How to fix it: The issue is the circuit board in the carriage (the black box with the fan, stepper motor and mounting for the smart extruder that rides on the rail). MakerBot won’t ship just the board, You have to buy the whole carriage assembly (board, stepper motor, fan, and housing which they will ship to for you to replace). We were quoted $250 for the part. Instructions show that it only takes a few minutes to change. It only requires the removal of the white ribbon cable and 4 hex bolts.
Smart Extruders v1: z18 vs. 5th Generation Versions
Except for the top cap and the bottom duct shroud, the 5th Generation smart extruder works on the z18, so if you have both a 5th Gen and a z18, you can just swap the cap and remove the lower duct shroud on a 5th Gen extruder to use on a z18 and vice versa.
Smart Extruders v2: z18 vs. 5th Generation Versions
Except for the top cap and the bottom duct shroud, the 5th Generation smart extruder works on the z18, so if you have both a 5th Gen and a z18, you can just swap the cap and remove the lower duct shroud on a 5th Gen extruder to use on a z18 and vice versa.
Я управляю лабораторией 3D-принтеров в средней школе, и у нас есть несколько принтеров MakerBot 5-го поколения. На одном из них у меня значительные проблемы с «тонкими» отпечатками и предупреждениями о проскальзывании нити.
До сих пор я безуспешно пытался заменить экструдеры и использовать разные рулоны. Но если я перенесу работу и экструдер на другой принтер, это сработает.
Буду признателен за предложения о том, как разобраться в этом. Я бы ожидал, что проблемы с проскальзыванием последуют за экструдером.
Ответы:
Ох, интересно. Под слайдами я понимаю, что вы имеете в виду, что сырая нить накала, а не печать.
Это произойдет по нескольким причинам. Первый зубчатый механизм, который захватывает пластмассу, является либо:
- Изношенный
- Не к месту
- Неправильное расстояние от направляющего колеса.
Это все часть механизма, который Smart Extruder присоединяет к TO. Не сам Умный Экструдер. Вы можете исправить это самостоятельно, в худшем случае вам понадобится замена сборки от MakerBot. Я бы посмотрел на сайты онлайн-аукционов для части
Другой вариант — попробовать более толстую нить. Который вы могли бы на заказ. Таким образом, вместо 1,5, возможно, получить 1,8. Я не уверен, где вы можете купить размеры.
Оттуда эта машина может просто застрять. Это случается с некоторыми машинами. Это снова указывает на основание оси X в сборе.
Последнее, что я бы сказал, маловероятно, поскольку вы попробовали несколько экструдеров, возможно, засорение сопла. Я часто открываю свою гарантию пустот экструдеров и очищаю их. Также здесь хорошо подходят ручные микро-дрели.
Хорошо, у оригинального Smart Extruder есть много проблем. Я проработал около 60 часов на новом Replicator + со Smart Extruder + и не столкнулся ни с одной из проблем, о которых я слышал с оригинальным экструдером. Итак, я мог бы начать с того, чтобы порекомендовать то, что MakerBot Industries рекомендовал своим клиентам, а именно обновить ваш Smart Extruder до нового Smart Extruder + .
Однако экструдер может быть не полностью виноват. На картинке написано тысяча слов, поэтому, если она у вас есть, добавьте ее. Основываясь на описании «истончения» слоев детали, дважды проверьте настройки выдавливания в MakerBot Desktop .
Другой потенциальной проблемой является слишком сильное натяжение нити, так как она подается в экструдер. Вот некоторые вещи, которые могут привести к чрезмерной напряженности :
- Нить намотана на катушку / держатель катушки
- Нить изогнута
- Слишком большое трение между катушкой и держателем катушки
- Слишком большое трение между нитью и направляющей нити (пластиковая трубка)
Наконец, и моя причина использования Smart Extruder заключается в том, что ваш экструдер может быть забит или «засорен». В прошлом, если было слишком сильное натяжение нити накала, и ведущая шестерня не была правильно отрегулирована, ведущая шестерня растирала нить накала. Это может привести к небольшим отложениям накала, приводящим к образованию зубчатой передачи, что в конечном итоге приведет к проскальзыванию нити. Как только нить начала проскальзывать, она больше не будет экструдироваться и нагреваться дальше до узла экструдера. Это неизбежно приводит к засорению экструдера. Короче говоря:
{Слишком сильное натяжение нити} + {Слишком плотное зубчатое колесо} = гуммирование
{Слишком много гуммирования} + Время = проскальзывание / «истончение»
{Слишком много проскальзываний} + время + тепло = засорение
Я разместил правку в верхнем ответе в надежде, что в будущем он будет изменен для всех, кто просматривает этот пост, но в случае отклонения здесь — это актуальная проблема и исправление.
Если вы просто хотите решение, перейдите к жирному тексту.
Я наткнулся на это сообщение, просматривая ресурсы для документирования своего собственного опыта с «проскальзыванием нити» в Makerbots, и каждое предлагаемое решение было неправильным и потенциально вредоносным для машины. Я эксперт в этой области и разобрал и починил десятки машин.
Сначала немного об анатомии экструдера, чтобы вы могли лучше понять. Способ, которым инструментальная головка обнаруживает проскальзывания, — это колесо энкодера, расположенное над реальным приводным механизмом, не прикрепленное к нему или к натяжному устройству. Он также даже не натянут на нить накала. Нить «удерживается» на месте с помощью пластмассового литья под давлением, который прикрепляется к остальной части корпуса экструдера только с помощью штыревых разъемов на внутренней печатной плате и небольшой установочной канавки с обеих сторон корпуса.
Колесо энкодера и его датчик маловероятно изнашиваются, но то, что происходит с каждой более старой головкой, заключается в том, что либо корпус, либо литая под давлением деталь, которая удерживает нить, изнашивается, и колесо энкодера больше не давит на нить, что заставляет нить двигаться без поворота энкодера. В этом случае датчик, который не двигается, когда находится ведущая шестерня, считывает квитанцию накала и отправляет сообщение об ошибке, даже если нет механических или функциональных ошибок. Износ также не очень хорошо виден даже при тщательном осмотре. Эта проблема возникает в каждом интеллектуальном экструдере, когда он достигает 150-200 часов печати.
Фактическое исправление
В качестве временного исправления вы можете зажать кусок пены внутри правой стороны экструдера, чтобы прижать плохо закрепленную литьевую деталь к колесу датчика. Это сделает ошибку проскальзывания нити гораздо реже, но не решит проблему полностью. Я работаю над 3D-печатной вставкой, которая должна надежно удерживать деталь, по крайней мере, до тех пор, пока напечатанная деталь не изнашивается после примерно 100 часов печати. Я также работаю над 3D-печатью замены корпуса экструдера и некоторых деталей, отлитых под давлением. Он призван стать заменой, что должно значительно повысить как надежность, так и функциональность. Если я смогу вспомнить, как только я закончу, я вернусь и опубликую ссылку здесь.
Вы также можете попробовать печатать при более высокой температуре. Проскальзывание может произойти, когда нить не плавится и, следовательно, не проходит через экструдер постоянно. Например, у меня была катушка из нити PLA, которая постоянно скользила при 190 ° C. Я попытался 220 ° C, и после этого он напечатал гладко.
У меня была такая же проблема, но мое решение было немного другим. Следуя тому, что другие писали о колесе, у меня возникло застревание внутри экструдера вокруг этого колеса. Я пропустил это в первый раз, когда разорвал его, поэтому независимо от того, сколько раз я пробовал трюк с отверткой, он не работал для меня.
Я подумал, что отправлю сообщение, так что если кто-нибудь придет и попытается найти решение, они увидят, что это может быть заклинивание на колесе накаливания, а не просто проверка области сопла.
Таким образом, у меня была эта проблема в течение многих месяцев, я собирался сдаться и назвать свой принтер весом бумаги, но я понял это. И это ничего не стоит.
Я буквально перепечатывал один и тот же переходник для шланга 6 раз (каждый раз, когда нить соскользнула примерно в 20 раз, и это было непригодно для использования). Я изменил 4 настройки, и с тех пор я печатал один и тот же отпечаток два раза подряд без единой накладной нити.
В «Настройках устройства» в приложении Makerbot: температура экструдера: 220 ° C. Скорость движения (я думаю, именно это и вызывает скольжение): 115 мм / с.
Затем в разделе «Заполнение»: Плотность заполнения: 30%
Наконец, в «Свойствах модели»: Начальная точка корпуса: 220 ° C
Пожалуйста, дайте мне знать, если это работает и для вас.
(Я должен отметить, что у меня просто есть обычный интеллектуальный экструдер, и я планировал сбросить 350 долларов за верхнюю часть линейной модели)
Я управляю лабораторией 3D-принтеров средней школы, и у нас есть несколько принтеров MakerBot 5-го поколения. На одном из них у меня возникли значительные проблемы с «тонкими» отпечатками и предупреждениями о проскальзывании нити.
До сих пор я пытался менять экструдеры и использовать различные рулоны филамента без успеха. Но если я перенесу работу и экструдер на другой принтер, он сработает.
Я был бы признателен за предложения о том, как во всем этом разобраться. Я ожидал, что проблемы со скольжением следуют за экструдером.
, 👍11
Обсуждение
7 ответов
О, интересно. Под промахами, я так понимаю, вы подразумеваете промахи необработанного филамента, а не промахи печати.
Это произойдет по нескольким причинам. Во-первых, зубчатая передача, которая захватывает пластик, либо:
- Изношенный
- Не к месту
- Неправильное расстояние от направляющего колеса.
Все это является частью механизма, к которому подключается Умный экструдер. Не сам Умный экструдер. Возможно, вы сможете исправить это самостоятельно, в худшем случае вам понадобится замена сборки от MakerBot. Я бы заглянул на сайты онлайн-аукционов по этой части
Другой вариант-попробовать более толстую нить. Которые вы могли бы заказать на заказ. Так что вместо 1,5, может быть, получится 1,8. Я не уверен, где вы можете купить меньшие размеры.
Оттуда эта машина может просто застрять. Это случается с некоторыми машинами. Это снова указывает на основание узла оси X.
Последнее, что я бы сказал, маловероятно, так как вы пробовали несколько экструдеров, возможно, у вас засорилось сопло. Я часто открываю гарантийные пустоты в экструдерах и очищаю их. Также хорошим вариантом здесь являются микро-ручные дрели.
20 дек 16,
@StarWind0
Хорошо, у оригинального интеллектуального экструдера много проблем. Я отработал около 60 часов на новом репликаторе+ с интеллектуальным экструдером+ и не столкнулся ни с одной из проблем, о которых я слышал, с оригинальным экструдером. Итак, я мог бы начать с повторной рекомендации того, что MakerBot Industries рекомендовала своим клиентам, а именно обновить ваш интеллектуальный экструдер до нового интеллектуального экструдера+.
Однакоэкструдер может быть не полностью неисправен. На картинке написано тысяча слов, поэтому, если у вас есть одно, пожалуйста, добавьте одно. Основываясь на вашем описании «утончения» слоев детали, дважды проверьте настройки экструзии в MakerBot Desktop.
Еще одной потенциальной проблемой является слишком большое натяжение нити при ее подаче в экструдер. Вот некоторые вещи, которые могут привести к слишком большому напряжению:
- Нить накала, намотанная вокруг катушки/держателя катушки
- Нить филамента перегнулась
- Слишком большое трение между катушкой и держателем катушки
- Слишком сильное трение между нитью и направляющей нити (пластиковой трубкой)
Наконец, и моя причина, по которой я упомянул об умном экструдере, заключается в том, что ваш экструдер может быть засорен или «застревает». В прошлом, если на филаменте было слишком большое натяжение и приводная передача была отрегулирована неправильно, приводная передача измельчала нить накала. Это привело бы к небольшим отложениям филамента на приводной передаче, что в конечном итоге привело бы к скольжению филамента. Как только нить начнет соскальзывать, она постепенно перестанет выдавливаться и будет нагреваться дальше по узлу экструдера. Это неизбежно приводит к засорению экструдера. Короче говоря:
{Слишком большое натяжение нити} + {Слишком жесткая ведущая передача} = Резинка
{Слишком много жевательной резинки} + Время = Скольжение/»Истончение»
{Слишком много скольжения} + время + тепло = Закупорка
20 дек 16,
@tbm0115
У нас была аналогичная проблема с нашим принтером Makerbot здесь, в лаборатории CARIS.
Мы бы проскальзывали, проскальзывали и пробовали смазывать, подавать вручную и грубить нить, но ничего из этого не работало. Но мы нашли ответ!!!
С помощью интеллектуального экструдера это так же просто, как вставить отвертку с плоской головкой между колесом накаливания и корпусом и подогнать колесо к контактной стороне печатающей головки. Решили все наши проблемы! Серьезно, с тех пор ни одного промаха и идеальные отпечатки.
У меня есть короткое видео с решением для YouTube, исправляющее скольжение нити на вашем 3D-принтере.
Ознакомьтесь со страницей устранения неполадок makerbot для справки: Поддержка MakerBot > Устранение неполадок >> Replicator MakerBot >>> Коды ошибок
ОШИБКА 81
9 апр 18,
@CARIS
Вы также можете попробовать печать при более высокой температуре. Скольжение может произойти, когда нить накала не плавится и, следовательно, не проходит последовательно через экструдер.
Например, у меня была катушка с нитью PLA, которая постоянно соскальзывала при температуре 190°C. Я попробовал 220°C, а затем он плавно напечатался после этого.
12 июн 18,
@Reece Markowsky
Я опубликовал правку в верхнем ответе в надежде, что она будет изменена для всех, кто посмотрит на этот пост в будущем, но в случае, если он будет отклонен, вот фактическая проблема и исправление.
Если вам просто нужно решение, перейдите к выделенному жирным шрифтом тексту.
Я наткнулся на это сообщение, просматривая ресурсы, чтобы документировать свой собственный опыт работы с «скольжением нити» в Makerbots, и каждое предлагаемое решение было неправильным и потенциально вредоносным для машины. Я эксперт в этой области и разобрал и починил десятки машин.
Сначала немного об анатомии экструдера, чтобы вы могли лучше понять. Инструментальная головка обнаруживает проскальзывания с помощью кодирующего колеса, расположенного над фактическим приводным механизмом, а не прикрепленного к нему или к зевакам вообще. Кроме того, он вообще не натянут на нить накала. Нить накала «удерживается» на месте с помощью отлитого под давлением куска пластика, который крепится к остальной части корпуса экструдера только с помощью штыревых разъемов на внутренней печатной плате и небольшого позиционирующего паза с обеих сторон корпуса.
Колесо энкодера и его датчик вряд ли изнашиваются, но с каждой более старой головкой происходит следующее: либо корпус, либо литая деталь, удерживающая нить накала, изнашиваются, и колесо энкодера больше не прижимается плотно к филаменту, что заставляет нить двигаться без поворота энкодера. Затем кодировщик, не двигаясь, пока работает ведущая передача, считывает проскальзывание филамента и отправляет сообщение об ошибке, даже если механически или функционально все в порядке. Износ также не заметен отчетливо даже при ближайшем рассмотрении. Эта проблема, по-видимому, возникает в каждом интеллектуальном экструдере+, как только он достигает 150-200 часов печати.
Фактическое Исправление
В качестве временного исправления вы можете вставить кусок пены с правой стороны экструдера, чтобы прижать плохо закрепленную литую деталь к колесу кодера. Это сделает ошибку со скольжением нити намного реже, но не решит проблему полностью. Я работаю над 3D-печатной вставкой, которая должна более надежно удерживать деталь, по крайней мере, до тех пор, пока печатная деталь не износится после дополнительных 100 или около того часов печати. Я также работаю над 3D-печатной заменой корпуса экструдера и некоторых литых под давлением внутренних деталей. Он призван стать каплей в замене, которая должна значительно повысить как надежность, так и функциональность. Если я смогу вспомнить, когда закончу, я вернусь и опубликую ссылку здесь.
6 июл 18,
@Adam Steinmark
У меня была та же проблема, но мое решение было немного другим. Следуя тому, что другие писали о колесе, у меня было замятие внутри экструдера вокруг этого колеса. Я пропустил это в первый раз, когда разорвал его, так что неважно, сколько раз я пробовал трюк с отверткой, это не сработало для меня.
Я подумал, что напишу, чтобы, если кто-то попытается найти решение, они могли увидеть, что это может быть замятие на колесе накаливания, а не просто для проверки области сопла.
6 фев 19,
@Steven Downs
Так что у меня была эта проблема в течение нескольких месяцев, и я уже собирался либо сдаться, либо назвать свой принтер пресс-папье, но потом сообразил. И это ничего не стоит.
Я буквально перепечатывал один и тот же адаптер шланга 6 раз (каждый раз филамент проскальзывала примерно 20 раз, и он был непригоден). Я изменил 4 настройки и с тех пор печатал один и тот же отпечаток дважды подряд без единого промаха нити филамента.
В разделе «Настройки устройства» приложения Makerbot:
Температура экструдера: 220 °C
Скорость перемещения (я думаю, что именно это на самом деле вызывает скольжение): 115 мм/с
Затем в разделе «Заполнение» :
Плотность заполнения: 30 %
Наконец, в разделе «Свойства модели»:
Начальная точка Оболочки: 220 °C
Пожалуйста, дайте мне знать, если это сработает и для вас.
(Я должен отметить, что у меня просто есть обычный интеллектуальный экструдер, и я планировал сбросить 350 долларов за верхнюю часть линейной модели)
17 апр 20,
@XMonsterX
$begingroup$
I run a high school 3D printer lab and we have several 5th generation MakerBot printers. On one of them I have considerable trouble with «thin» prints and filament slip warnings.
So far I’ve tried changing extruders and using different filament rolls with no luck. But, if I move the job and the extruder to a different printer it works.
I’d appreciate suggestions for how to sort this out. I would have expected the slipping problems to follow the extruder.
asked Dec 20, 2016 at 15:28
$endgroup$
2
$begingroup$
Oh interesting. By slips, I take it you mean that the raw filament slips, not the print slips.
This will happen for a few reasons. First the tooth gear that grabs the plastic is either:
- Worn out
- Out of place
- Not the correct distance from the guide wheel.
This is all part of the mechanism that the Smart Extruder attaches TO. Not the Smart Extruder itself. You might be able to fix this yourself, worst case you will need a replacement assembly from MakerBot. I would look into online auction sites for the part
Another option is to try thicker filament. Which you might be able to custom order. So instead of 1.5, maybe get 1.8. I am not sure where you can buy off sizes.
From there this machine might just be getting jammed. It happens to some machines. This again points to the base of the X axis assembly.
Last which I would say is not likely as you have tried multiple extruders, you might have the nozzle becoming clogged. I often pop open my extruders voids warranty and clean them out. Also micro hand drills are a good option here.
dlu
3261 gold badge2 silver badges11 bronze badges
answered Dec 20, 2016 at 20:59
StarWind0♦StarWind0
3,0333 gold badges12 silver badges29 bronze badges
$endgroup$
1
$begingroup$
I posted an edit to the top answer in hopes that it will get changed for anyone looking at this post in the future but in case it gets rejected here is the actual issue and fix.
If you just want the solution skip down to the bolded text.
I came across this post while browsing for resources to document my own experiences with «filament slip» in Makerbots and every suggested solution was wrong and potentially malicious to the machine. I’m an expert in the field and have taken apart and fixed dozens of machines.
First a bit about the anatomy of the extruder so you can understand better. The way that the toolhead detects slips is with an encoder wheel placed above the actual drive mechanism, not attached to it or the idler whatsoever. It’s also not even tensioned against the filament at all. The filament is «held» in place with an injection molded piece of plastic that attaches to the rest of the extruder body just by the pin connectors on the internal PCB and a small positioning groove on both sides of the case.
The encoder wheel and its sensor are very unlikely to wear but what happens to every older head is that either the casing or the injection molded part that holds the filament wears and the encoder wheel no longer presses firmly against the filament which causes the filament to move without turning the encoder. The encoder then not moving while the drive gear is, reads a filament slip and sends an error message even though nothing is mechanically or functionally wrong. The wear is also not clearly visible even on close inspection. This problem seems to arise in every Smart Extruder+ once it reaches 150-200 printing hours.
Actual Fix
As a temporary fix you can jam a piece of foam inside the right side of the extruder to push the poorly secured injection molded part against the encoder wheel. This will make the filament slip error much less frequent but won’t completely solve the issue. I’m working on a 3D printed insert that should hold the part more securely, at least until the printed part wears after an additional 100 or so printing hours. I’m also working on a 3D printed replacement for the extruder body and some of the injection molded interior parts. It aims to be a drop in replacement which should greatly improve both reliability and functionality. If I can remember once I’m finished I’ll come back and post a link here.
Greenonline♦
5,9017 gold badges30 silver badges62 bronze badges
answered Jul 6, 2018 at 17:34
$endgroup$
2
$begingroup$
Okay, the original Smart Extruder has many issues. I’ve clocked about 60 hours on a new Replicator+ w/ Smart Extruder+ and haven’t encountered any of the issues I heard about with the original extruder. So, I might begin by re-recommending what MakerBot Industries has recommended to their customers which is upgrade your Smart Extruder to the new Smart Extruder+.
However, the extruder may not be completely at fault. A picture says a thousand words, so if you have one, please add one. Based on your description of the part’s layers «thinning out», double check your extrusion settings in MakerBot Desktop.
Another potential issue is too much tension on the filament as it is being fed into the extruder. Here are some things that can lead to too much tension:
- Filament wound around spool/spool holder
- Filament kinked
- Too much friction between the spool and spool holder
- Too much friction between the filament and the filament guide (the plastic tube)
Finally, and my reason for bringing up the Smart Extruder, is that your extruder may be clogged or «gumming up». In the past, if there was too much tension on the filament and the drive gear was not adjusted correctly, the drive gear would grind the filament. This would lead to small deposits of filament gumming up the drive gear, eventually leading to the filament slipping. Once the filament began slipping, it would slowly no longer extrude and heat up further up the extruder assembly. This inevitably leads to the extruder becoming clogged. In short:
{Too much filament tension} + {Too tight drive gear} = Gumming
{Too much gumming} + Time = Slipping/»Thinning»
{Too much slipping} + time + heat = Clogging
answered Dec 20, 2016 at 21:41
tbm0115tbm0115
6,2742 gold badges19 silver badges40 bronze badges
$endgroup$
$begingroup$
You could also try printing at a higher temperature. Slips can happen when the filament is not melting and thus not pushing through the extruder consistently.
E.g. I had a spool of PLA filament that would slip constantly at 190°C. I tried 220°C and then it printed smoothly after that.
0scar♦
32.8k10 gold badges60 silver badges137 bronze badges
answered Jun 12, 2018 at 18:07
$endgroup$
$begingroup$
I had the same issue, but my solution was a little different. Following along with what the others posted about the wheel, I had a jam inside the extruder around that wheel. I missed it the first time I tore it open so no matter how many times I tried the screwdriver trick it didn’t work for me.
I figured I’d post so if anyone is coming along trying to find the solution, they can see that it might be a jam on the filament wheel and not just to check the nozzle area.
answered Feb 6, 2019 at 16:08
$endgroup$
$begingroup$
We had a similar issue with our Makerbot printer here in the CARIS lab.
We would have slip, after slip and tried oiling, hand feeding, and roughing up the filament none of it worked. But we found an answer!!!
With the smart extruder, it’s as simple as inserting a flathead screwdriver between the filament wheel and the housing, and prying the wheel towards the pin-side of the print head. Solved all our problems! Seriously, not a slip since and perfect prints.
I’ve a short solution video for YouTube, Fixing filament slip on your 3D printer.
Check out the makerbot trouble shooting page for reference: MakerBot Support > Troubleshooting > MakerBot Replicator > Error Codes
ERROR 81
Greenonline♦
5,9017 gold badges30 silver badges62 bronze badges
answered Apr 9, 2018 at 20:22
CARISCARIS
111 bronze badge
$endgroup$
$begingroup$
So I had this issue for months, was about to either give up and call my printer a paper weight, but I figured it out. And it doesn’t cost anything.
I literally reprinted the same hose adapter 6 times (every time the filament slipped about 20 times and it was unusable). I changed 4 settings and since then I’ve printed the same print twice in a row without a single filament slip.
In «Device Settings» in Makerbot application:
Extruder Temp: 220 °C
Travel Speed (I think this is what is actually causing the slip): 115 mm/s
Then in the «Infill» section:
Infill Density: 30 %
Lastly in «Model Properties»:
Shell Starting Point: 220 °C
Please let me know if this works for you as well.
(I should point out I just have the regular smart extruder, and I was planning on dumping the $350 for the top of the line model)
0scar♦
32.8k10 gold badges60 silver badges137 bronze badges
answered Apr 17, 2020 at 14:29
$endgroup$
1
You must log in to answer this question.
Not the answer you’re looking for? Browse other questions tagged
.
Not the answer you’re looking for? Browse other questions tagged
.