I acquired an MSi RTX 3080 Ventus 3x OC from a friend who used it to mine along with other 3080s (Trio, Strix, FTW3 Ultra).
This one has an outdated BIOS version without resizable bar, which I wanted to test. So, I tried to flash it and:
-can’t flash it with newest nvflash following all the steps in guides, CMD as admin, even tried in safe mode, gives me error «Adapter not accessible or supported EEPROM not found, skipping» and «ERROR: Detecting GPU failed.»
-can’t save the current bios with nvflash, gives me error «ERROR: A system restart might be required before running the utility.» and restarting does not work.
-can’t remove the protection with —protectoff, gives me error «ERROR: A system restart might be required before running the utility.» which again does not work.
-can’t save current bios with GPU-Z, gives me the «bios reading not supported on this device» (this is the first thing I tried)My friend told me he never changed the bios, all he did was save it with Hiveos (he did change pads and thermal paste)
GPU-Z shows me all the info, including the bios version no problem there, and the card works, except it has a low performance compared to other 3080s: furmark bench at 1080p is around 16000 points when in other 3080s is 17000; also in Unigine Superposition is a similar matter.
My friend told me to install Hiveos and he would flash my card from his home as apparently one can’t do it in the same computer and I have only one now…
I was thinking of using a bootable USB and see if I could do it that way, but I don’t know if I will need another card to do so, I guess no…Any ideas?
GPU-Z capture:
View attachment 273342
I acquired an MSi RTX 3080 Ventus 3x OC from a friend who used it to mine along with other 3080s (Trio, Strix, FTW3 Ultra).
This one has an outdated BIOS version without resizable bar, which I wanted to test. So, I tried to flash it and:
-can’t flash it with newest nvflash following all the steps in guides, CMD as admin, even tried in safe mode, gives me error «Adapter not accessible or supported EEPROM not found, skipping» and «ERROR: Detecting GPU failed.»
-can’t save the current bios with nvflash, gives me error «ERROR: A system restart might be required before running the utility.» and restarting does not work.
-can’t remove the protection with —protectoff, gives me error «ERROR: A system restart might be required before running the utility.» which again does not work.
-can’t save current bios with GPU-Z, gives me the «bios reading not supported on this device» (this is the first thing I tried)
My friend told me he never changed the bios, all he did was save it with Hiveos (he did change pads and thermal paste)
GPU-Z shows me all the info, including the bios version no problem there, and the card works, except it has a low performance compared to other 3080s: furmark bench at 1080p is around 16000 points when in other 3080s is 17000; also in Unigine Superposition is a similar matter.
My friend told me to install Hiveos and he would flash my card from his home as apparently one can’t do it in the same computer and I have only one now…
I was thinking of using a bootable USB and see if I could do it that way, but I don’t know if I will need another card to do so, I guess no…
Any ideas?
GPU-Z capture:
Bro don’t worry it’s not about a mined card or bla bla whatever the comments are making this a poop party.
I wanted to reflash my 3080 g x trio from the suprim bios bcoz i be running it 24hrs for awhile.
I FACED(so read for the good part) i’d the same issue prompting restart required and gpuz saying is not supported whatever F’s
After some research i’d a hunch the manufacturers have a shadow deal with these bunch.
Skip gpuz and dont use the latest nvflash, its made to make us feel like be bricked our cards or so
Download this version of nvflash 5.667
NVIDIA NVFlash (5.792.0) Download
NVIDIA NVFlash is used to flash the graphics card BIOS on Ampere, Turing, Pascal and all older NVIDIA cards. NVFlash supports BIOS flashing on NVID
www.techpowerup.com
If u notice there is no 32 or 64 bit version. Look up tech power up for your correct bios.
Follow the standard step
1.
Nvflash -b backup.rom
2.
Nvflash — — protectoff
3.
Nvflash -6 with your new bios.rom
Wah la! I hoped it helps, at this point of clicking send i am boarding my plane, i hope when i land i hope to see it helped you
Well, me and my friend did the Hiveos thing and he managed to save and flash the bios of my GPU from his terminal…so there might be a problem with my Windows 10?
I will test the bootable USB way, to see if I can do a —protectoff and a saving of bios with nvflash, that would be en
I acquired an MSi RTX 3080 Ventus 3x OC from a friend who used it to mine along with other 3080s (Trio, Strix, FTW3 Ultra).
This one has an outdated BIOS version without resizable bar, which I wanted to test. So, I tried to flash it and:
-can’t flash it with newest nvflash following all the steps in guides, CMD as admin, even tried in safe mode, gives me error «Adapter not accessible or supported EEPROM not found, skipping» and «ERROR: Detecting GPU failed.»
-can’t save the current bios with nvflash, gives me error «ERROR: A system restart might be required before running the utility.» and restarting does not work.
-can’t remove the protection with —protectoff, gives me error «ERROR: A system restart might be required before running the utility.» which again does not work.
-can’t save current bios with GPU-Z, gives me the «bios reading not supported on this device» (this is the first thing I tried)My friend told me he never changed the bios, all he did was save it with Hiveos (he did change pads and thermal paste)
GPU-Z shows me all the info, including the bios version no problem there, and the card works, except it has a low performance compared to other 3080s: furmark bench at 1080p is around 16000 points when in other 3080s is 17000; also in Unigine Superposition is a similar matter.
My friend told me to install Hiveos and he would flash my card from his home as apparently one can’t do it in the same computer and I have only one now…
I was thinking of using a bootable USB and see if I could do it that way, but I don’t know if I will need another card to do so, I guess no…Any ideas?
GPU-Z capture:
View attachment 273342
I acquired an MSi RTX 3080 Ventus 3x OC from a friend who used it to mine along with other 3080s (Trio, Strix, FTW3 Ultra).
This one has an outdated BIOS version without resizable bar, which I wanted to test. So, I tried to flash it and:
-can’t flash it with newest nvflash following all the steps in guides, CMD as admin, even tried in safe mode, gives me error «Adapter not accessible or supported EEPROM not found, skipping» and «ERROR: Detecting GPU failed.»
-can’t save the current bios with nvflash, gives me error «ERROR: A system restart might be required before running the utility.» and restarting does not work.
-can’t remove the protection with —protectoff, gives me error «ERROR: A system restart might be required before running the utility.» which again does not work.
-can’t save current bios with GPU-Z, gives me the «bios reading not supported on this device» (this is the first thing I tried)My friend told me he never changed the bios, all he did was save it with Hiveos (he did change pads and thermal paste)
GPU-Z shows me all the info, including the bios version no problem there, and the card works, except it has a low performance compared to other 3080s: furmark bench at 1080p is around 16000 points when in other 3080s is 17000; also in Unigine Superposition is a similar matter.
My friend told me to install Hiveos and he would flash my card from his home as apparently one can’t do it in the same computer and I have only one now…
I was thinking of using a bootable USB and see if I could do it that way, but I don’t know if I will need another card to do so, I guess no…Any ideas?
GPU-Z capture:
View attachment 273342
Bro don’t worry it’s not about a mined card or bla bla whatever the comments are making this a poop party.
I wanted to reflash my 3080 g x trio from the suprim bios bcoz i be running it 24hrs for awhile.
I FACED(so read for the good part) i’d the same issue prompting restart required and gpuz saying is not supported whatever F’s
After some research i’d a hunch the manufacturers have a shadow deal with these bunch.
Skip gpuz and dont use the latest nvflash, its made to make us feel like be bricked our cards or so
Download this version of nvflash 5.667
NVIDIA NVFlash (5.792.0) Download
NVIDIA NVFlash is used to flash the graphics card BIOS on Ampere, Turing, Pascal and all older NVIDIA cards. NVFlash supports BIOS flashing on NVID
www.techpowerup.com
If u notice there is no 32 or 64 bit version. Look up tech power up for your correct bios.
Follow the standard step
1.
Nvflash -b backup.rom
2.
Nvflash — — protectoff
3.
Nvflash -6 with your new bios.rom
Wah la!
I acquired an MSi RTX 3080 Ventus 3x OC from a friend who used it to mine along with other 3080s (Trio, Strix, FTW3 Ultra).
This one has an outdated BIOS version without resizable bar, which I wanted to test. So, I tried to flash it and:
-can’t flash it with newest nvflash following all the steps in guides, CMD as admin, even tried in safe mode, gives me error «Adapter not accessible or supported EEPROM not found, skipping» and «ERROR: Detecting GPU failed.»
-can’t save the current bios with nvflash, gives me error «ERROR: A system restart might be required before running the utility.» and restarting does not work.
-can’t remove the protection with —protectoff, gives me error «ERROR: A system restart might be required before running the utility.» which again does not work.
-can’t save current bios with GPU-Z, gives me the «bios reading not supported on this device» (this is the first thing I tried)My friend told me he never changed the bios, all he did was save it with Hiveos (he did change pads and thermal paste)
GPU-Z shows me all the info, including the bios version no problem there, and the card works, except it has a low performance compared to other 3080s: furmark bench at 1080p is around 16000 points when in other 3080s is 17000; also in Unigine Superposition is a similar matter.
My friend told me to install Hiveos and he would flash my card from his home as apparently one can’t do it in the same computer and I have only one now…
I was thinking of using a bootable USB and see if I could do it that way, but I don’t know if I will need another card to do so, I guess no…Any ideas?
GPU-Z capture:
View attachment 273342
I acquired an MSi RTX 3080 Ventus 3x OC from a friend who used it to mine along with other 3080s (Trio, Strix, FTW3 Ultra).
This one has an outdated BIOS version without resizable bar, which I wanted to test. So, I tried to flash it and:
-can’t flash it with newest nvflash following all the steps in guides, CMD as admin, even tried in safe mode, gives me error «Adapter not accessible or supported EEPROM not found, skipping» and «ERROR: Detecting GPU failed.»
-can’t save the current bios with nvflash, gives me error «ERROR: A system restart might be required before running the utility.» and restarting does not work.
-can’t remove the protection with —protectoff, gives me error «ERROR: A system restart might be required before running the utility.» which again does not work.
-can’t save current bios with GPU-Z, gives me the «bios reading not supported on this device» (this is the first thing I tried)
My friend told me he never changed the bios, all he did was save it with Hiveos (he did change pads and thermal paste)
GPU-Z shows me all the info, including the bios version no problem there, and the card works, except it has a low performance compared to other 3080s: furmark bench at 1080p is around 16000 points when in other 3080s is 17000; also in Unigine Superposition is a similar matter.
My friend told me to install Hiveos and he would flash my card from his home as apparently one can’t do it in the same computer and I have only one now…
I was thinking of using a bootable USB and see if I could do it that way, but I don’t know if I will need another card to do so, I guess no…
Any ideas?
GPU-Z capture:
Bro don’t worry it’s not about a mined card or bla bla whatever the comments are making this a poop party.
I wanted to reflash my 3080 g x trio from the suprim bios bcoz i be running it 24hrs for awhile.
I FACED(so read for the good part) i’d the same issue prompting restart required and gpuz saying is not supported whatever F’s
After some research i’d a hunch the manufacturers have a shadow deal with these bunch.
Skip gpuz and dont use the latest nvflash, its made to make us feel like be bricked our cards or so
Download this version of nvflash 5.667
NVIDIA NVFlash (5.792.0) Download
NVIDIA NVFlash is used to flash the graphics card BIOS on Ampere, Turing, Pascal and all older NVIDIA cards. NVFlash supports BIOS flashing on NVID
www.techpowerup.com
If u notice there is no 32 or 64 bit version. Look up tech power up for your correct bios.
Follow the standard step
1.
Nvflash -b backup.rom
2.
Nvflash — — protectoff
3.
Nvflash -6 with your new bios.rom
Wah la!
Well, me and my friend did the Hiveos thing and he managed to save and flash the bios of my GPU from his terminal…so there might be a problem with my Windows 10?
I will test the bootable USB way, to see if I can do a —protectoff and a saving of bios with nvflash, that would be enWell, me and my friend did the Hiveos thing and he managed to save and flash the bios of my GPU from his terminal…so there might be a problem with my Windows 10?
I will test the bootable USB way, to see if I can do a —protectoff and a saving of bios with nvflash, that would be enough for me.
Bro don’t worry it’s not about a mined card or bla bla whatever the comments are making this a poop party.
I wanted to reflash my 3080 g x trio from the suprim bios bcoz i be running it 24hrs for awhile.
I FACED(so read for the good part) i’d the same issue prompting restart required and gpuz saying is not supported whatever F’s
After some research i’d a hunch the manufacturers have a shadow deal with these bunch.
Skip gpuz and dont use the latest nvflash, its made to make us feel like be bricked our cards or so
Download this version of nvflash 5.667
NVIDIA NVFlash (5.792.0) Download
NVIDIA NVFlash is used to flash the graphics card BIOS on Ampere, Turing, Pascal and all older NVIDIA cards. NVFlash supports BIOS flashing on NVID
www.techpowerup.com
If u notice there is no 32 or 64 bit version. Look up tech power up for your correct bios.
Follow the standard step
1.
Nvflash -b backup.rom
2.
Nvflash — — protectoff
3.
Nvflash -6 with your new bios.rom
Wah la!
I acquired an MSi RTX 3080 Ventus 3x OC from a friend who used it to mine along with other 3080s (Trio, Strix, FTW3 Ultra).
This one has an outdated BIOS version without resizable bar, which I wanted to test. So, I tried to flash it and:
-can’t flash it with newest nvflash following all the steps in guides, CMD as admin, even tried in safe mode, gives me error «Adapter not accessible or supported EEPROM not found, skipping» and «ERROR: Detecting GPU failed.»
-can’t save the current bios with nvflash, gives me error «ERROR: A system restart might be required before running the utility.» and restarting does not work.
-can’t remove the protection with —protectoff, gives me error «ERROR: A system restart might be required before running the utility.» which again does not work.
-can’t save current bios with GPU-Z, gives me the «bios reading not supported on this device» (this is the first thing I tried)My friend told me he never changed the bios, all he did was save it with Hiveos (he did change pads and thermal paste)
GPU-Z shows me all the info, including the bios version no problem there, and the card works, except it has a low performance compared to other 3080s: furmark bench at 1080p is around 16000 points when in other 3080s is 17000; also in Unigine Superposition is a similar matter.
My friend told me to install Hiveos and he would flash my card from his home as apparently one can’t do it in the same computer and I have only one now…
I was thinking of using a bootable USB and see if I could do it that way, but I don’t know if I will need another card to do so, I guess no…Any ideas?
GPU-Z capture:
View attachment 273342
| Автор | Сообщение | |||
|---|---|---|---|---|
|
||||
Moderator Статус: Не в сети |
Здесь обсуждаются только видеокарты NVIDIA RTX 3070Ti (GA104-400)|RTX 3070 (GA104-300)|| RTX 3060Ti (GA104-200) и конкретные технические вопросы по ним. Всё остальное, включая цены, выбор и приобретение, майнинг и т.д. решаются в других темах: СМЕЖНЫЕ ТЕМЫ Помощь в выборе видеокарты + FAQ Подробные технические характеристики и модели: RTX 3070Ti |RTX 3070 | RTX 3060 Ti В данной теме в полной мере действуют ПРАВИЛА КОНФЕРЕНЦИИ Код:
Чтобы видео можно было воспроизвести прямо на странице форума, используйте теги: Код: Показать скрытое содержание [media]Ваше видео[/media]
>>>F.A.Q.<<< Обзоры GeForce RTX 3070 1. Nvidia RTX 3070 — референс — от ixbt GeForce RTX 3060 Ti 1. MSI GeForce RTX 3060 Ti Gaming X Trio — от techpowerup Полезные ссылки и информация о видеокартах Ampere
|
Добавлено: 05.12.2020 11:35 | Реклама | |
|
Партнер |
|
Sabotender |
|
|
Member Статус: Не в сети |
AHDPEY198329477 писал(а): Кулера не могут крутится, так как они к плате при кручены, тем более на видеокартах 1 кулер. А вот вентиляторы крутятся, это такие круглые штуки с лопастями, они при 2100 прилично шумят. Позанудствую… кулер это система охлаждения — т.е. пассивный радиатор, радиатор + вентилятор (активный), СВО (радиаторы, вентиляторы, помпа, шланги) и т.п. это все кулера. |
|
Allianz |
|
|
Junior Статус: Не в сети |
Доброго времени суток, камрады. Нужна помощь Ваша! |
|
sergtrav |
|
|
Member Статус: Не в сети |
Allianz писал(а): При попытке использования утилиты nvflash64, после ввода команды в cmd —protectoff, на экране бьет ошибку. ERROR: A system restart might be required before running the utility. Надо вводить «nvflash64 —protectoff . Программа должна быть в корне диска С. Добавлено спустя 4 минуты 3 секунды: |
|
Ramforce |
|
|
Member Статус: Не в сети |
sergtrav писал(а): на тихой прошивке А на «не тихой» работает? |
|
Allianz |
|
|
Junior Статус: Не в сети |
sergtrav писал(а): Надо вводить «nvflash64 —protectoff . Программа должна быть в корне диска С. Капитан Последний раз редактировалось Allianz 15.11.2022 13:06, всего редактировалось 1 раз. |
|
sergtrav |
|
|
Member Статус: Не в сети |
Ramforce писал(а): А на «не тихой» работает? Да и не на тихой не работает, как выяснилось. |
|
foetopsy |
|
|
Member Статус: Не в сети |
Обладатели Евга 3070ти имею карту с марта, там на дроселях термопста, высохла, на чипе тоже сухарь, не майнил, нагрузка не большая, вот ездил ТП купил |
прокладки Laird Tflex 300 плотностью 1,2 Вт/мК. Термопаста ShinEtsu 3w/mk, на памяти Тп 2,25 толщина|
tonygks |
|
|
Member Статус: Не в сети |
foetopsy писал(а): Нашёл инфу как по термопссте так и термопрокладкам даже что использует Евга прокладки Laird Tflex 300 плотностью 1,2 Вт/мК. Термопаста ShinEtsu 3w/mk, на памяти Тп 2,25 толщина Удачи все это хорошо дожать при сборке. Более жесткие прокладки или чуть толще чем надо и привет плохой прижим чипа/памяти/дрмоса. |
|
IDimm |
|
|
Member Статус: Не в сети |
Привет всем. Имею EVGA GeForce RTX 3070 Ti FTW3, как управлять её подсветкой? Утилита Mistyc Light из MSI Center её не видит, на самой карте есть разъём ARGB, если подключить его к материнке появится возможность управлять подсветкой и синхронизировать с подсветкой остальных комплектующих из Mistyc Light? |
|
XenneX |
|
|
Member Статус: Не в сети |
IDimm |
|
Sabotender |
|
|
Member Статус: Не в сети |
IDimm писал(а): если подключить его к материнке появится возможность управлять подсветкой и синхронизировать с подсветкой остальных комплектующих из Mistyc Light Для этого эти разъемы и делают… что бы управлять с МП. |
|
IDimm |
|
|
Member Статус: Не в сети |
Для этого эти разъемы и делают… что бы управлять с МП. Я вроде как прочитал, что с этого разъёма видеокарта будет управлять подключенными к этому разъёму устройствами, т.е. синхронизировать со своей подсветкой, или я не правильно понял? |
|
Battlenelf |
|
|
Member Статус: Не в сети |
AHDPEY198329477 ну я из любопытства потестил, если наушники снять и вручную без нагрузки гонять вентиляторы через мси аб, то небольшой шум появляется на 1800 об/мин, но даже гулом это не назвать, так, едва слышно. Вот на 2000-2100 он становится более явным, но без какого-либо треска или завывания, шум процессорного кулера это перекрывает. Плюс у меня ещё боковая стенка корпуса пластиковая и с дырками, так что в более качественном корпусе наверное будет не так слышно. В общем, относительно прошлой карты эта почти бесшумная |
|
Sabotender |
|
|
Member Статус: Не в сети |
IDimm писал(а): т.е. синхронизировать со своей подсветкой Я сомневаюсь в EVGA работают идиоты =) правда вопрос, надо ли ставить софт от ВК или нет — всё равно открытый. |
|
sergtrav |
|
||
|
Member Статус: Не в сети |
Разобрался с Resizible Bar благодаря подсказкам в GPU-Z, оказывается, нужно не только включить его и Above 4G decoding в БИОС, но и отключить CSM там же. Остался только вопрос, какого лешего CSM самостоятельно включился после смены видеокарты.
|
|
SCANDAL |
|
|
Junior Статус: Не в сети |
sergtrav писал(а): Разобрался с Resizible Bar благодаря подсказкам в GPU-Z, оказывается, нужно не только включить его и Above 4G decoding в БИОС, но и отключить CSM там же. Остался только вопрос, какого лешего CSM самостоятельно включился после смены видеокарты. толку то от этого всего? выше несколько постов о бесполезности данной приблуды… |
|
sergtrav |
|
|
Member Статус: Не в сети |
Цитата: толку то от этого всего? выше несколько постов о бесполезности данной приблуды… Душу греет. Да и не совсем бесполезно, на 3060 прирост в Киберпанке был с 74 до 77 кадров, наверное, на 3070 будет не хуже, но проверять лень. |
|
Alexshanghai |
|
|
Member Статус: Не в сети |
sergtrav писал(а): Душу греет. Да и не совсем бесполезно, на 3060 прирост в Киберпанке был с 74 до 77 кадров, наверное, на 3070 будет не хуже, но проверять лень. в сети есть инструкция для нвидия инспектора. (тулза такая) как включить BAR во всех запускаемых на пк приложениях не зависимо от того поддерживают они эту фичу или нет. |
|
Alexey A |
|
|
Member Статус: Не в сети |
Сегодня поставил карту-ту,что в профиле.В ГПУ з показывает 2 вентиля вместо трех.Там типа 2 за 1 считается,или как? |
—
| Вы не можете начинать темы Вы не можете отвечать на сообщения Вы не можете редактировать свои сообщения Вы не можете удалять свои сообщения Вы не можете добавлять вложения |
Лаборатория
Новости
-
Главная
-
Dakar Техно-Грааль
-
Гайд как прошить биос на видеокарте Nvidia RTX 3080 | разгон видеокарты | настройка msi afterburner
Просмотров: 2 605
Если вам понравилось бесплатно смотреть видео гайд как прошить биос на видеокарте nvidia rtx 3080 | разгон видеокарты | настройка msi afterburner онлайн которое загрузил Dakar Техно-Грааль 24 ноября 2021 длительностью 00 ч 10 мин 02 сек в хорошем качестве, то расскажите об этом видео своим друзьям, ведь его посмотрели 2 605 раз.
Grigor Taroyan
2 недели назад
можно ли изменить серийник на видеокарте через прошивку? nvidia k2000. я заплачу за услуги
Ігор Дуванов
2 недели назад
Там нет 3050, шо делать?
Дизель Мистер
3 недели назад
спасибо помог видео карту MSI gtx 980 TI обновил версию биоса до последней версии
suren suren
3 недели назад
Здравствуйте подскажите карта 3080ti aorus xtreme waterforce сдохла и выдает ошибку 43. Черный экран и ниче более. Гарантийника нет. Если попробую прошить получится? Или хуже сделаю?
RoboPig Cop
4 недели назад
Отличный гайд,но китайские поддельные «видеокарты»,удастся прошить только через программатор,да и то вряд-ли.Я попытался прошить способом из видео,поддельную 1050 ti на родной биос gtx 450,ничего не вышло,черный экран,перезагрузка компа.
RuslanKT
1 месяц назад
Почему GPU Z не сохраняет БИОС? карта 3060TI PALIT
Danil
1 месяц назад
Этот способ не работает больше , пробовал и 3060 и 3060ti и 3070 protectoff прописываешь, экран 2 раза мигнёт и просит перезагрузить комп
da_da_ne_udivlyaites
1 месяц назад
“GPU Device ID mismatch”
У кого была такая ошибка? Помогите, пожалуйста, разобраться🙏🏻
ПодливаShow
1 месяц назад
Прива p106-100 прошить получится так? И какой прогой редактировать биос?
Nikolay Kim
1 месяц назад
Всем привет, подскажите у меня проблема палит 3080, в фурмарте работает чётко, а вот в игре пабг ком перезагружается блок питания гамакс 1200 ват. В чем может быть причина
Саня Травмат
1 месяц назад
Видеокарта Asus 3060 Ti TUF (lhr)
При попытке выключить защиту выдает ошибку : ERROR: A system restart might be required before running the utility.
перезагружаешь , то же самое … Не кто не сталкивался с этим?
В GPU z нажимаешь сохранить bios пишет : bios reading not supported on this device …
При попытке установить с зхащитой пишет ERROR: Detecting GPU failed.
STARTABL
1 месяц назад
а если экран не гаснет и биос не прошивается?? в консоле всё нормально, но на кнопку (y) нажать не просит (?
алексей петелько
1 месяц назад
не пробуйте этот метод запорите биос ,я седня по этому методу прошить биос gigabyte rtx 3060 gaming oc 12g пытался перепрошить ,запорол биос видеокарты все делал как в видео !!
Nikita Vasilev
2 месяца назад
По гайду успешно прошился, только эффект вышел скорее негативный. На всех трёх вариантах Биоса с разными значениями power limit, что я попробовал, карта начинала жрать на 100 ватт больше, при этом частота падала на 300 MHz ниже, даже на тех значениях вольтажа и частот, на которых карта укладывалась в старый power limit.
P.s. Тестировал в Cyberpunk 2077 и стресс тесте AIDA64, карта msi 3080 ventus 3x oc 12gb
Music Hard
2 месяца назад
Решение проблемы у кого не шьеться («ERROR: A system restart might be required before running the utility.) Качайте версию NvFlash которая в Видео (nvflash_5.715) с ней все прошилось!
E1_PJ
2 месяца назад
Glu pci device id mesmatch. 3070 гейрок. Все биосы гейрока попробовал — везде такая ошибка
ShPiLi WiLLy
2 месяца назад
ERROR: Detecting GPU failed.
Станислав
2 месяца назад
У меня второй раз экран потух и больше не включился….
Саня Шевченко
2 месяца назад
Серега, подскажи пожалуста, если такую ошибку дает при попытке сохранить био? —bios reading not supported on this device, чего делать ? если пробовать прошить возможно кирпич и только програматор?
Содержание
- Ошибки при установке программ из пакета Windows Installer «.msi»
- Ошибки msi файлов
- Ещё способы решить проблему
- Ошибка установщика Windows
- Параметры реестра и службы
- Подведение итогов
- question
- Windows Updates on Win10 prompts to restart before it finishes installing updates
- 3 Answers
- Get help with Windows upgrade and installation errors
- General fixes
- 0xC1900101 Errors
- Other Common Errors
- General fixes
- 0xC1900101 Errors
- Other Common Errors
Ошибки при установке программ из пакета Windows Installer «.msi»
Вообще, меня это жутко бесит, т.к. после глупого сообщения об ошибке совсем непонятно что делать дальше. Microsoft специально разработали установщик Windows Installer для расширения возможностей установки программ (в основном это касается системных администраторов), но не позаботились должным образом о безглючной работе этой службы или хотя бы об адекватных сообщениях о проблемах. А нам теперь это разгребать 🙂
Неполадки могут быть с работой самой службы или могут возникать в процессе установки программ, когда всё настроено, в принципе, правильно. В первом случае нужно ковырять службу установщика, а во втором решать проблему с конкретным файлом. Рассмотрим оба варианта, но сначала второй.
Ошибки msi файлов
«Error reading from file «имя файла» verify that the file exists and that you can access it» (Error 1305). Переводится «Ошибка чтения из файла … проверьте существует ли файл и имеете ли вы к нему доступ». Ну не тупняк ли? Естественно, что кнопка «Повторить» не помогает, а отмена прекращает всю установку. Сообщение особой смысловой нагрузки также не несёт, т.к. файл точно существует и я имею к нему доступ, иначе бы просто не смог его запустить и получить это сообщение, к тому же почему-то на английском языке 🙂
А ошибка в том, что не Я должен иметь доступ к файлу, а установщик Windows, точнее сама Система. Решается очень просто:
Теперь ошибка установщика не появится! Можно добавить доступ на всю папку, из которой вы обычно инсталлируете программы, например на папку «Downloads», как у меня. Смотрим видео по решению проблем с правами доступа:
Ещё способы решить проблему
Описанный метод поможет при разных сообщениях, с разными номерами. Например, вы можете видеть такие ошибки файлов msi:
Во всех этих случаях должна помочь установка прав на файл и/или на некоторые системные папки. Проверьте, имеет ли доступ «система» к папке временных файлов (вы можете получать ошибку «Системе не удается открыть указанное устройство или файл»). Для этого:
После нажатия «Enter» путь преобразится на «нормальный» и вы переместитесь в реальную временную папку. Права на неё и надо проверять. Также рекомендую очистить временные папки от всего что там скопилось или даже лучше удалить их и создать новые с такими же названиями. Если не получается удалить папку, почитайте как удалить неудаляемое, но это не обязательно.
Если служба Windows Installer всё равно не хочет работать, то проверьте права на папку «C:Config.Msi», сюда «система» также должна иметь полный доступ. В этом случае вы могли наблюдать ошибку «Error 1310». На всякий случай убедитесь, что к папке КУДА вы инсталлируете софт также есть все права.
Если вы используете шифрование папок, то отключите его для указанных мной папок. Дело в том, что хотя мы сами имеем к ним доступ, служба Microsoft Installer не может до них достучаться пока они зашифрованы.
Ещё ошибка может быть связана с битым файлом. Может быть он не полностью скачался или оказался битым уже на сервере. Попробуйте скачать его ещё раз оттуда же или лучше с другого места.
Ошибка установщика Windows
В случае общих проблем не будут устанавливаться никакие msi файлы, процесс установки, скорее всего, даже не начнётся. При этом могут появляться ошибки вида:
или ещё нечто подобное со словами «ошибка msi», «Windows Installer Error». Всё это означает, что система дала сбой и теперь её надо лечить. Может вы ставили какой-то софт, который испортил системные файлы и реестр, или подхватили вирус. Конечно, никогда не будет лишним удалить вирусы, или убедиться что их нет. Но оставьте этот вариант на потом, т.к. обычно проблема кроется в другом.
Сначала давайте проверим работает ли служба Windows Installer:
Следующее что я посоветую сделать – это выполнить команду сканирования системы на повреждённые и изменённые системные файлы. Нажмите «Win + R» и введите
Sfc /scannow
Произойдёт поиск и замена испорченных файлов на оригинальные, при этом может потребоваться вставить установочный диск с Windows XP-7-10. После окончания процесса перегрузитесь и посмотрите, решена ли проблема.
Microsoft сам предлагает утилиту, призванную решить нашу проблему. Запустите программу Easy Fix и следуйте мастеру.
Параметры реестра и службы
Следующий способ устранения ошибки – восстановление рабочих параметров в реестре установщика Windows Installer.
Для этого скачайте архив и запустите оттуда два reg-файла, соответственно своей версии Windows. Согласитесь с импортом настроек.
В Windows XP или Windows Server 2000 установите последнюю версию установщика 4.5.
Если не помогло, то проделайте ещё перерегистрацию компонентов:
Если пишет, что не хватает прав, то нужно запускать командную строку от имени Администратора.
Если команды выполнились, но не помогло, то скачайте файл и запустите msi_error.bat из архива, проверьте результат.
Последний вариант — скачайте программу Kerish Doctor, почитайте мою статью, там есть функция исправления работы службы установщика и многих других частых проблем Windows.
Подведение итогов
Ошибки с установщиком Windows очень неприятные, их много и сразу непонятно куда копать. Одно ясно – система дала сбой и нужно восстанавливать её до рабочего состояния. Иногда ничего не помогает и приходится переустанавливать Windows. Однако не торопитесь это делать, попробуйте попросить помощи на этом форуме. В точности опишите вашу проблему, расскажите что вы уже делали, какие сообщения получили, и, возможно, вам помогут! Ведь мир не без добрых людей 🙂
Источник
question
Windows Updates on Win10 prompts to restart before it finishes installing updates
Hi there. I have a few Windows 10 PCs configured in Windows Update to restart as soon as updates are complete.
If I install updates by (manually) going to Windows Updates and check for updates, the updates are found and installation begins.
However, Windows Updates prompts to restart the computer before all updates have finished installing.
So for example, in the picture I’ve attached here, Windows Updates is 40% through installing the May 2022 cumulative update.
The blue pop-up window appears (as well as the Windows Update restart icon in the taskbar) telling you it’s time to restart Windows.
When I click to restart, I (briefly) see in the background that Windows hadn’t actually finished installing all updates.
Sure enough, after Windows reboots, when I go back to WU and check «View Update History» I see the May 2022 updates is not listed, so I have to start all over again.
This seems like a bug to me. I want the computer to restart when it’s finished installing all updates, not halfway through.
Just checking in to see if the information provided was helpful.
If the reply helped you, please remember to accept as answer.
If no, please reply and tell us the current situation in order to provide further help.
We have not get information from you for several days.
If the reply is useful for you, please accept as answer. It will be helpful to other members who have same questions.
If you have any other confuse, please reply to us directly.
3 Answers
Hmm. While the KB5003173 update is not listed under View Installation History, it is listed under Control Panel > Programs and Features > View Installed Updates.
Bizarre.
@SirTimbit-5632
Hi,
When windows updates, it first downloading files from whatever storage of MS there is.
Then it start to look thought packages your system already has and downloaded.
After this there is a dependency mechanism on what package need what actions to be performed: for example you have packages downloaded.
The system during update can for example check that package «pack2» needs reboot and be installed only after «pack1» should be installed onto system, because of this it will need a complete system reboot.
That is why you could see The blue pop-up window appears.
During the restating, Windows will apply changes updates produced.
Also, only updates installed by Windows Update appear in Update History.
But all updates, however they were installed, are shown in Installed Updates in Control Panel.
Hope above information can help you.
============================================
If the Answer is helpful, please click «Accept Answer» and upvote it.
Note: Please follow the steps in our documentation to enable e-mail notifications if you want to receive the related email notification for this thread.
@JennyFeng-MSFT
Thanks for getting back to me. That makes sense. I get that some updates would depend on other updates already being installed.
But in this case I had other machines configured the same way, where I didn’t restart the PC immediately.
I ignored the prompt to reboot for a few minutes and let the install continue.
On those PCs, the 2022-05 update completed installation and then I rebooted, so it doesn’t seem the reboot halfway through was necessary.
@SirTimbit-5632
Hi,
You are right, whether you need to restart depends on your choice, while the prompt to reboot is by design.
After the reboot, an early upgrade task checks if core components like the registry itself have been updated and moves the new files into place if so, then begins the normal upgrade process for registered desktop components that begins by unregistering the old version, moving the new file in place of the old, and registering the new version. Once that is complete, the system boots normally, using the new versions.
============================================
If the Answer is helpful, please click «Accept Answer» and upvote it.
Источник
Get help with Windows upgrade and installation errors
There are many reasons why you might receive an error message when upgrading or installing Windows 11, but common errors can be fixed with a few steps that you can do on your own. Note: An upgrade takes your device from an older version of Windows, such as Windows 7, Windows 8.1, or Windows 10 to Windows 11.
Before searching for a specific error code, try the tips listed in General fixes. If those don’t fix your upgrade or installation problem, check the table of error codes at the bottom of this article.
General fixes
Here are some things you can try to fix upgrade and installation errors:
Unplug any nonessential hardware devices. These could include headphones, printers, scanners speakers, USB flash drives, and external hard drives.
If you’re using a laptop and it’s plugged in to a docking station, undock it.
It’s a good idea to make sure that all important updates are installed before trying to upgrade Windows. This includes updates to hardware drivers on your device.
For information and to make sure you’re up-to-date, see Windows Update: FAQ.
Use Windows Defender to protect your device during the upgrade—non-Microsoft antivirus software can sometimes cause upgrade problems. As long as you have installation media and all required activation information, you can always reinstall the software after you upgrade.
To remove an antivirus application, go to Control PanelProgramsPrograms and Features. Select the program, and then select Uninstall. Select Yes to confirm.
Outdated software can cause problems with a Windows upgrade, so removing old or nonessential applications can help.
If you plan to reinstall the application later, make sure you have the installation media and all required activation information before removing it.
To uninstall software, go to Control PanelProgramsPrograms and Features. Select the program, and then select Uninstall. Select Yes to confirm.
To upgrade to Windows 11, you need enough space on your hard drive for the installation to take place.
To view how much hard drive space is available on your computer, select File Explorer on the taskbar (known as Windows Explorer in Windows 7) or press Windows logo key + E.
Then select Computer or This PC and look under Hard Disk Drives or under Devices and drives. If there are multiple drives listed, the system drive is the drive that includes a Microsoft Windows logo above the drive icon. You’ll see the amount of available space under the drive.
If it looks like your drive is running low on space, see Tips to free up drive space on your PC.
0xC1900101 Errors
An error that begins with 0xC1900101 is usually a driver error. If you see any of these error codes, try the following steps first to fix the problem. If these steps don’t work, see Resolve Windows upgrade errors for more detailed technical info.
Make sure that your device has enough space. Your device requires at least 16 GB of free space to upgrade a 32-bit OS, or 20 GB for a 64-bit OS. For more info, see Free up drive space in Windows.
Run Windows Update a few times. Download and install any available updates in Windows Update, including software updates, hardware updates, and some third-party drivers. Use the Windows Update Troubleshooter to fix Windows 11 Update errors.
Check third-party drivers and download any updates. You can find third-party drivers and installation instructions for any hardware you’ve added to your device on the manufacturer’s website.
Unplug extra hardware. Remove all external storage devices and drives, docks, and other hardware you might have plugged into your device that isn’t needed for basic functionality.
Check Device Manager for errors. In the search box on the taskbar, type device manager. Choose Device Manager from the results. In the window that pops up, look for any device with a yellow exclamation mark beside it (you may have to select each category to switch to the list of devices). Press and hold (or right-click) the device name and select either Update Driver Software or Uninstall to correct the errors.
Remove third-party security software. Make sure you know how to reinstall your programs and that any necessary product keys are on hand. Windows Defender will help protect your device in the meantime.
Repair hard-drive errors. In the search box on the taskbar, type command prompt. Choose Command Prompt from the list of results. In the window that pops up, type chkdsk/f C: and press the Enter key. Repairs automatically start on your hard drive, and you’ll be asked to restart your device.
Note: You must have administrator permissions on your device to do this.
Restore and repair system files. In the search box on the taskbar, type command prompt. Choose Command Prompt from the list of results. In the window that pops up, type DISM.exe /Online /Cleanup-image /Restorehealth and press the Enter key. (Learn to repair a Windows image)
Note: You must have administrator permissions on your device to do this.
Other Common Errors
The following table lists the most common upgrade and installation errors and some things you can try to fix them. If you continue having problems upgrading or installing Windows, contact Microsoft support.
What it means and how to fix it
This indicates that there was a problem downloading and installing the selected update. Windows Update will try again later and there is nothing you need to do at this time.
This could indicate that an incompatible app installed on your PC is blocking the upgrade process from completing. Check to make sure that any incompatible apps are uninstalled and then try upgrading again.
A cleanup operation from a previous installation attempt is still pending, and a system restart is required to continue the upgrade. Restart the device and run setup again. If restarting device does not resolve the issue, then use the Disk Cleanup utility and clean up the temporary files and the System files. For more information, see Disk cleanup in Windows.
A file needed by Windows Update is likely damaged or missing. Try repairing your system files: In the search box on the taskbar, type command prompt. Choose Command Prompt from the list of results. In the window that appears, type DISM.exe /Online /Cleanup-image /Restorehealth and press the Enter key.
This may signify that your PC doesn’t meet the minimum requirements to download or install the upgrade to Windows 11. Learn more about the minimum requirements for Windows 11.
This might indicate that a driver or other software on your PC isn’t compatible with the upgrade to Windows 11. For info about how to fix this problem, contact Microsoft support.
This could mean that the upgrade process was interrupted because you accidentally restarted your PC or signed out of your PC. Try upgrading again and make sure your PC is plugged in and stays turned on.
This error might mean that your PC couldn’t connect to the Windows Update servers. If you’re using a VPN connection to connect to a work network, disconnect from the network and turn off the VPN software (if applicable) and try upgrading again.
The error could also mean there isn’t enough free space in the System Reserved partition. You might be able to fix this problem by using third-party software to increase the size of the System Reserved partition.
Error: We couldn’t complete the updates. Undoing changes. Don’t turn off your computer.
Error: Failure configuring Windows Updates. Reverting changes.
These are generic errors that might appear any time a Windows update fails. You’ll need to determine the specific error code to investigate how to best resolve this problem.
You can find the error code for the failed update by viewing your update history. Look for the update that wasn’t installed, note the error code, and then contact Microsoft support.
To view your update history in Windows 11:
Select Start > Settings > Windows Update > Update history.
Error: The update isn’t applicable to your computer.
This error might mean that your PC doesn’t have the required updates installed.
Check to make sure that all important updates are installed on your PC before you try upgrading.
This likely indicates that your PC doesn’t have enough space available to install the upgrade.
Free some space on the drive and try again. Get tips for freeing up drive space
The specified disk operation is not supported by the target disk, partition, or volume.
Make sure your machine meets the minimum requirements to install Windows.
The system cannot find the file specified.
If you have a disk or disks where you are not installing Windows 11 on, remove those disks.
A driver has caused a problem.
Disable or remove all 3rd party antivirus or antispyware from your system. Disconnect all peripheral devices that are connected to the system, except for the mouse, keyboard and display.
Contact your hardware vendor to obtain updated device drivers.
Windows Setup terminated unexpectedly due to another process running in the background.
When you start Windows by using a normal startup, several applications and services start automatically, and then run in the background. These programs include basic system processes, antivirus software, system utility applications, and other software that has been previously installed. These applications and services can cause interference when you attempt to upgrade to the latest version of Windows 11.
To help you determine whether a background program is interfering with the upgrade, a «clean boot» may be needed. See How to perform a clean boot in Windows.
Windows Setup terminated unexpectedly due to another process running in the background.
Uninstall any antivirus or antispyware software and update again.
There are many reasons why you might receive an error message when upgrading or installing Windows 10, but common errors can be fixed with a few steps that you can do on your own. Note: An upgrade takes your device from an older version of Windows, such as Windows 7 or Windows 8.1, to Windows 10.
Before searching for a specific error code, try the tips listed in General fixes. If those don’t fix your upgrade or installation problem, check the table of error codes at the bottom of this article.
General fixes
Here are some things you can try to fix upgrade and installation errors:
Unplug any nonessential hardware devices. These could include headphones, printers, scanners speakers, USB flash drives, and external hard drives.
If you’re using a laptop and it’s plugged in to a docking station, undock it.
It’s a good idea to make sure that all important updates are installed before trying to upgrade Windows. This includes updates to hardware drivers on your device.
For information and to make sure you’re up-to-date, see Windows Update: FAQ.
Use Windows Defender to protect your device during the upgrade—non-Microsoft antivirus software can sometimes cause upgrade problems. As long as you have installation media and all required activation information, you can always reinstall the software after you upgrade.
To remove an antivirus application, go to Control PanelProgramsPrograms and Features. Select the program, and then select Uninstall. Select Yes to confirm.
Outdated software can cause problems with a Windows upgrade, so removing old or nonessential applications can help.
If you plan to reinstall the application later, make sure you have the installation media and all required activation information before removing it.
To uninstall software, go to Control PanelProgramsPrograms and Features. Select the program, and then select Uninstall. Select Yes to confirm.
To upgrade to Windows 10, you need enough space on your hard drive for the installation to take place.
To view how much hard drive space is available on your computer, select the Start button, then in the search box on the taskbar, type File Explorer (known as Windows Explorer in Windows 7).
Then select Computer or This PC and look under Hard Disk Drives or under Devices and drives. If there are multiple drives listed, the system drive is the drive that includes a Microsoft Windows logo above the drive icon. You’ll see the amount of available space under the drive.
If it looks like your drive is running low on space, see Tips to free up drive space on your PC.
0xC1900101 Errors
An error that begins with 0xC1900101 is usually a driver error. If you see any of these error codes, try the following steps first to fix the problem. If these steps don’t work, see Resolve Windows upgrade errors for more detailed technical info.
Make sure that your device has enough space. Your device requires at least 16 GB of free space to upgrade a 32-bit OS, or 20 GB for a 64-bit OS. For more info, see Free up drive space in Windows.
Run Windows Update a few times. Download and install any available updates in Windows Update, including software updates, hardware updates, and some third-party drivers. Use the Windows Update Troubleshooter to fix Windows Update errors.
Check third-party drivers and download any updates. You can find third-party drivers and installation instructions for any hardware you’ve added to your device on the manufacturer’s website.
Unplug extra hardware. Remove all external storage devices and drives, docks, and other hardware you might have plugged into your device that isn’t needed for basic functionality.
Check Device Manager for errors. Select the Start button, then in the search box on the taskbar, type device manager. Choose Device Manager from the results. In the window that pops up, look for any device with a yellow exclamation mark beside it (you may have to select each category to switch to the list of devices). Press and hold (or right-click) the device name and select either Update Driver Software or Uninstall to correct the errors.
Remove third-party security software. Make sure you know how to reinstall your programs and that any necessary product keys are on hand. Windows Defender will help protect your device in the meantime.
Repair hard-drive errors. Select the Start button, then in the search box on the taskbar, type command prompt. Choose Command Prompt from the list of results. In the window that pops up, type chkdsk/f C: and press the Enter key. Repairs automatically start on your hard drive, and you’ll be asked to restart your device.
Note: You must have administrator permissions on your device to do this.
Do a clean restart into Windows. Learn how.
Restore and repair system files. Select the Start button, then in the search box on the taskbar, type command prompt. Choose Command Prompt from the list of results. In the window that pops up, type DISM.exe /Online /Cleanup-image /Restorehealth and press the Enter key. (Learn to repair a Windows image)
Note: You must have administrator permissions on your device to do this.
Other Common Errors
The following table lists the most common upgrade and installation errors and some things you can try to fix them. If you continue having problems upgrading or installing Windows 10, contact Microsoft support.
What it means and how to fix it
This indicates that there was a problem downloading and installing the selected update. Windows Update will try again later and there is nothing you need to do at this time.
This could indicate that an incompatible app installed on your PC is blocking the upgrade process from completing. Check to make sure that any incompatible apps are uninstalled and then try upgrading again.
A cleanup operation from a previous installation attempt is still pending, and a system restart is required to continue the upgrade. Restart the device and run setup again. If restarting device does not resolve the issue, then use the Disk Cleanup utility and clean up the temporary files and the System files. For more information, see Disk cleanup in Windows.
A file needed by Windows Update is likely damaged or missing. Try repairing your system files: Select the Start button and type command prompt in the search box on the taskbar. Choose Command Prompt from the list of results. In the window that appears, type DISM.exe /Online /Cleanup-image /Restorehealth and press the Enter key.
This may signify that your PC doesn’t meet the minimum requirements to download or install the upgrade to Windows 10. Learn more about the minimum requirements for Windows
This might indicate that a driver or other software on your PC isn’t compatible with the upgrade to Windows 10. For info about how to fix this problem, contact Microsoft support.
This could mean that the upgrade process was interrupted because you accidentally restarted your PC or signed out of your PC. Try upgrading again and make sure your PC is plugged in and stays turned on.
This error might mean that your PC couldn’t connect to the Windows Update servers. If you’re using a VPN connection to connect to a work network, disconnect from the network and turn off the VPN software (if applicable) and try upgrading again.
The error could also mean there isn’t enough free space in the System Reserved partition. You might be able to fix this problem by using third-party software to increase the size of the System Reserved partition.
Error: We couldn’t complete the updates. Undoing changes. Don’t turn off your computer.
Error: Failure configuring Windows Updates. Reverting changes.
These are generic errors that might appear any time a Windows update fails. You’ll need to determine the specific error code to investigate how to best resolve this problem.
You can find the error code for the failed update by viewing your update history. Look for the update that wasn’t installed, note the error code, and then contact Microsoft support.
To view your update history in Windows 8.1:
Open Windows Update by swiping in from the right edge of the screen (or, if you’re using a mouse, pointing to the lower-right corner of the screen and moving the mouse pointer up), select Settings > Change PC settings > Update and recovery > View your update history.
To view your update history in Windows 7:
Select the Start 
button. In the search box, type Update, and then, in the list of results, Select Windows Update > View update history.
Error: The update isn’t applicable to your computer.
This error might mean that your PC doesn’t have the required updates installed.
Check to make sure that all important updates are installed on your PC before you try upgrading.
This likely indicates that your PC doesn’t have enough space available to install the upgrade.
Free some space on the drive and try again. Get tips for freeing up drive space
The specified disk operation is not supported by the target disk, partition, or volume.
Make sure your machine meets the minimum requirements to install Windows 10.
The system cannot find the file specified.
If you have a disk or disks where you are not installing Windows 10 on, remove those disks.
A driver has caused a problem.
Disable or remove all 3rd party antivirus or antispyware from your system. Disconnect all peripheral devices that are connected to the system, except for the mouse, keyboard and display.
Contact your hardware vendor to obtain updated device drivers.
Windows Setup terminated unexpectedly due to another process running in the background.
When you start Windows by using a normal startup, several applications and services start automatically, and then run in the background. These programs include basic system processes, antivirus software, system utility applications, and other software that has been previously installed. These applications and services can cause interference when you attempt to upgrade to the latest version of Windows 10.
To help you determine whether a background program is interfering with the upgrade, a «clean boot» may be needed. See How to perform a clean boot in Windows.
Windows Setup terminated unexpectedly due to another process running in the background.
Uninstall any antivirus or antispyware software and update again.
Источник