Error code 0x0005fbb6 lib math c

Error code: 0X0005FBB6 LIB_MATH C

Hi @TH5BH3C0R9,

Welcome to the HP Support Community

I understand you are getting an error message 0X0005FBB6 LIB_MATH C  on your HP DeskJet Ink Advantage 4535 Printer. Not to worry I will help you to get a resolution to resolve the issue.

We need to perform a Semi full reset to restore the printer back to its original settings.

The reset instructions are specific for your printer and performing those steps on a different printer may brick the device. 

I’ve sent you a private message with reset instructions, follow the reset instruction to perform a full reset and re-initialize the printer. 

In order to access your private messages, click the private message icon on the upper right corner of your HP Community profile, next to your profile Name or simply click on this link.

Hope this helps! Keep me posted. 

Please click “Accepted Solution” if you feel my post solved your issue, it will help others find the solution. Click the “Kudos/Thumbs Up» on the bottom right to say “Thanks” for helping!


ANAND_ANDY
I am an HP Employee

Источник

Как устранить ошибку 0005fbb6 в принтерах HP: Эта ошибка может возникать в струйных принтерах марки HP. В этой статье опишем возможные решения, которые помогут удалить такую ошибку с дисплея принтера.

Эта ошибка может
возникать в струйных принтерах марки
HP. Ниже опишем возможные решения, которые
помогут удалить такую ошибку с дисплея
принтера.

Первое возможное
решение:

  • Удалите драйверы
    принтера. (Желательно отключить принтер
    от сети и USB-кабеля от компьютера).
  • Пока принтер отсоединен
    от компьютера, скачайте драйверы принтера из Интернета и установите их снова.
  • Подключите кабель USB к
    принтеру снова . Проверьте, что компьютер
    распознает принтер, и повторите попытку
    печати.

Второе возможное
решение: (обнуление принтера)

  • При включенном принтере,
    отключите кабель USB.
  • Выньте струйные картриджи
    из принтера.
  • Подождите десять секунд
    и отключите кабель питания от принтера.
  • Пока принтер выключен,
    подождите около 60 секунд.
  • Подключите принтер к
    сети снова.
  • Если принтер не включился
    от подсоединения кабеля к сети, нажмите
    на кнопку питания на принтере.
  • Вставьте картриджи и
    закройте крышку, дающие доступ к ним.
  • Подключите кабель USB к
    принтеру снова.

Третье возможное решение
(обнуление настроек до заводского
состояния)

  • Перейдите в » СВОЙСТВА
    «, затем » ИНСТРУМЕНТЫ» и нажмите,
    когда появится «восстановить настройки
    принтера до заводского состояния».
  • Перезагрузите принтер
    .

Источник

Содержание

  1. Error code 0x0005fbb6 lib math c
  2. Re: HP Officejet Pro 8500A error 0005FBB6
  3. Re: HP Officejet Pro 8500A error 0005FBB6
  4. Re: HP Officejet Pro 8500A error 0005FBB6
  5. Re: HP Officejet Pro 8500A error 0005FBB6
  6. Re: HP Officejet Pro 8500A error 0005FBB6
  7. Re: HP Officejet Pro 8500A error 0005FBB6
  8. Re: HP Officejet Pro 8500A error 0005FBB6
  9. Re: HP Officejet Pro 8500A error 0005FBB6
  10. Re: HP Officejet Pro 8500A error 0005FBB6
  11. Кто сейчас на конференции
  12. Error code 0x0005fbb6 lib math c
  13. Error code 0x0005fbb6 lib math c
  14. Error code 0x0005fbb6 lib math c
  15. Error code 0x0005fbb6 lib math c

Error code 0x0005fbb6 lib math c

stranger » 07:21 — 11.12.12

Re: HP Officejet Pro 8500A error 0005FBB6

Сервис-центр СКАН » 07:26 — 11.12.12

Re: HP Officejet Pro 8500A error 0005FBB6

stranger » 09:20 — 11.12.12

Re: HP Officejet Pro 8500A error 0005FBB6

stranger » 05:15 — 13.12.12

Re: HP Officejet Pro 8500A error 0005FBB6

Сервис-центр СКАН » 14:39 — 14.12.12

Re: HP Officejet Pro 8500A error 0005FBB6

stranger » 10:52 — 15.12.12

Re: HP Officejet Pro 8500A error 0005FBB6

Сервис-центр СКАН » 12:16 — 15.12.12

В мануале по HP при такой ошибке ещё рекомендуют сделать следующее:
1. Включить принтер.
2. Отсоединить USB кабель.
3. Вытащить картриджи из принтера.
4. Выдернуть шнур питания.
5. Подождать 60 секунд.
6. Подключить шнур питания. Если принтер сам не начнет грузиться, нажать кнопку питания.
7. Установить картриджи и закрыть все крышки.
8. Если запросит печать страницы калибровки, выполнить её.
9. Подсоединить USB и попробовать произвести печать.
10. Если не помогает, на этом они рекомендуют обратиться в сервис HP.

Если не поможет, то можно ещё попробовать перезагрузить NVRAM:
1. Включить принтер.
2. Отсоединить USB.
3. При работающем принтере выдернуть шнур питания.
4. Нажать и удерживать кнопки # и 3 одновременно.
5. Удерживая кнопки # и 3 подключить кабель питания. пока идет процесс загрузки (мигает кнопка питания).
6. Дальше следую инструкциям установить новые настройки. (т.к. все будет сброшено).
7. Если работать не начнет попробовать заменить картриджи с чернилами.

Если и это не поможет, думаю лучше уже нести к сервисникам в HP.

Re: HP Officejet Pro 8500A error 0005FBB6

stranger » 12:20 — 17.12.12

Re: HP Officejet Pro 8500A error 0005FBB6

Сервис-центр СКАН » 12:34 — 17.12.12

Re: HP Officejet Pro 8500A error 0005FBB6

stranger » 13:13 — 17.12.12

  • Похожие темы Ответы Просмотры Последнее сообщение
  • HP1300 ошибка: Fuser error. The fuser has a malfunction.
    fikus в форуме HEWLETT PACKARD (HP) 12 5812 fikus
    23:23 — 23.10.11
  • Лазерный принтер Brother HL-2030 — Error «Paper» останавливается бумага при начале печати.
    simatic в форуме BROTHER 6 17414 человек
    10:57 — 31.01.07
  • Canon BJC-6500 выдают «BJ Cartridge error»
    Егоров М.Н. в форуме Струйные принтеры 1 2933 tishka
    00:43 — 19.06.09
  • МФУ Epson RX500 пишет error и «обраитесь к докуметации»
    Светланка в форуме EPSON 2 2765 Светланка
    15:09 — 18.11.11
  • Копир Xerox WorkCentre 312 — «Open heat error»
    в форуме XEROX 3 12559 vo_van
    15:26 — 16.05.11

Кто сейчас на конференции

Сейчас этот форум просматривают: нет зарегистрированных пользователей и гости: 17

Источник

Error code 0x0005fbb6 lib math c

‎07-02-2022 08:15 AM

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

i’m getting 0x0005FBB6 when i switch on my hp officejet 3830 printer.

I tried all below suggested steps multiple times but that’s not helping

Remove the ink cartridges, and reset the printer

Remove the ink cartridges from the printer.

With the printer turned on , disconnect the power cord from the printer.

Unplug the power cord from the power source.

Wait at least 60 seconds.

Reconnect the power cord to a wall outlet and to the printer.

HP recommends plugging the printer directly into a wall outlet.

Turn the printer on.

Reinsert the ink cartridges, and then close the ink cartridge access door.

‎07-05-2022 05:20 AM

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

Thank you for posting on the HP Support Community.

Don’t worry as I’ll be glad to help,

I appreciate your efforts to try and resolve the issue.
This seems like a hardware issue with the printer. Let’s check for any paper jams inside the printer and make sure the printer carriage is moving freely.

Refer to the steps mentioned in this document — Paper Jam Error

If the error persists, I’m sending out a private message to assist you with the next course of action. Please check your Private message icon on the upper right corner of your HP Community profile Next, to your profile Name, you should see a little blue envelope, please click on it or simply click on this link: https://h30434.www3.hp.com/t5/notes/privatenotespage

Hope this helps! Keep me posted for further assistance.
Please click “ Accept as Solution ” if you feel my post solved your issue, it will help others find the solution. Click the “Kudos, Thumbs Up» on the bottom right to say “Thanks” for helping!

Источник

Error code 0x0005fbb6 lib math c

‎10-17-2022 07:24 AM — last edited on ‎10-19-2022 07:44 AM by Ric_ob

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

Error code: 0X0005FBB6 LIB_MATH C

‎10-24-2022 12:26 PM

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

I’ve tried everything to clear this error code seems like HP should have a solution since they have a code!

My Office jet 4650 shows error code 0X0005FBB6 whenever I try to make copies or try to scan both from app and directly from Printer. Everything else seems to work ie. test pages, cartridge alignment, wireless print jobs just can not copy or scan

‎10-26-2022 10:42 AM

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

Welcome to the HP Support Community

I understand you are getting an error message 0X0005FBB6 LIB_MATH C on your HP DeskJet Ink Advantage 4535 Printer . Not to worry I will help you to get a resolution to resolve the issue.

We need to perform a Semi full reset to restore the printer back to its original settings.

The reset instructions are specific for your printer and performing those steps on a different printer may brick the device.

I’ve sent you a private message with reset instructions, follow the reset instruction to perform a full reset and re-initialize the printer.

In order to access your private messages, click the private message icon on the upper right corner of your HP Community profile, next to your profile Name or simply click on this link .

Hope this helps! Keep me posted.

Please click “ Accepted Solution ” if you feel my post solved your issue, it will help others find the solution. Click the “ Kudos/Thumbs Up » on the bottom right to say “ Thanks ” for helping!

ANAND_ANDY
I am an HP Employee

Источник

Error code 0x0005fbb6 lib math c

‎01-09-2013 01:52 PM

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

My printer all of sudden displays the 0005FBB6 and blue screen. I have tried the hard reset. Nothing. What can I do?

‎12-27-2013 07:01 PM

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

Its wifi connection error. It would be good if HP could fix this with new firmware.

‎01-09-2013 02:13 PM

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

What model is the printer? And is it 0005FBB6 or 0x05FBB6 that is displayed?

I was a support engineer for HP.

If the advice resolved the situation, please mark it as a solution. Thank you.

‎01-09-2013 02:17 PM

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

Model 8500A Pro premium

The error code is 0005FBB6

‎04-04-2013 03:25 PM

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

Please help my P C S HP C6380 shows a blue screen and very briefly 0005FBB6 the printer then asks to be switched off and on again and an orange light, on light and print photos lights flash. what dose this mean?

‎12-05-2013 07:53 AM

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

Excuse me, where is the solution? I do not see anywhere around. I just bought the Photosmart 6520 series and this is only the fourth day of use.

There was a paper jam which I cleared. Now it is not working, asking me to turn off and then on again. When I did that, it started and then this message 0005FBB6 flash for a moment and then I was asked to turn off and then on again. This happens over and over again. Please help.

Источник

Error code 0x0005fbb6 lib math c

‎01-21-2018 09:50 AM

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

scanner wont scan keeps giving me a error code 0x0005fbb6

‎01-22-2018 05:19 PM

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

Welcome to the HP Forums, this is a great location to get assistance! I read your post and see that you are getting error code 0x0005fbb6. I would like to help you resolve this issue.

However, I will need a few details to provide an accurate solution,

  • When did this issue start?
  • Did you do any hardware or software changes?
  • How is the printer connected to computer, wired or wireless?

Perform a power reset

  1. Turn on the printer, if it is not already on.
  2. Wait until the printer is idle and silent before you continue.
  3. With the printer turned on , disconnect the power cord from the rear of the printer.
  4. Wait at least 30 seconds.
  5. Reconnect the power cord to the rear of the printer.
  6. Turn on the printer

Reply with the result of the above-mentioned steps, for further assistance.

Sandytechy20
I am an HP Employee

‎01-24-2018 01:15 AM

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

‎01-24-2018 12:13 PM

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

Thanks for the reply.

I appreciate your time and effort.

Eager to know, did you get time to perform power reset in the printer.

If not, follow the below steps:

  1. Turn on the printer, if it is not already on.
  2. Wait until the printer is idle and silent before you continue.
  3. With the printer turned on , disconnect the power cord from the rear of the printer.
  4. Wait at least 30 seconds.
  5. Reconnect the power cord to the rear of the printer.
  6. Turn on the printer.

If the issue persists, Update the printer firmware.

Click here and refer the document to update the printer firmware.

Let me know how it goes.

Sandytechy20
I am an HP Employee

‎01-24-2018 05:09 PM

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

To correct error 0x0005fbb6, try the following :

  • Uninstall the existing printer driver
  • Disconnect the USB cable and disconnect the power cable from your printer and the AC outlet
  • Download the latest driver on the HP website
  • Start the driver installation
  • Reconnect the cables when the installation process tells you to.

If the above procedure doesn’t do the trick, try the following:

  • With the Printer on, disconnect the USB cable.
  • Remove the ink cartridges
  • Wait about 10 seconds then disconnect the power cord from the printer and AC outlet
  • Wait approximately 1 minute then reconnect the power cord to the printer and the AC outlet
  • If the printer doesn’t turn on, press the power button to turn it on.
  • Reinstall the ink cartridges and close the door.
  • Reconnect the USB cable.

If neither of thes two procedures work, then reset to factory defaults as follows:

  • Go to «Setup»
  • Select «Tools»
  • Select «Restore Factory Defaults»
  • Power your printer down then turn it back on.

Источник

Источник

Error code 0x0005fbb6 lib math c

stranger » 07:21 — 11.12.12

Re: HP Officejet Pro 8500A error 0005FBB6

Сервис-центр СКАН » 07:26 — 11.12.12

Re: HP Officejet Pro 8500A error 0005FBB6

stranger » 09:20 — 11.12.12

Re: HP Officejet Pro 8500A error 0005FBB6

stranger » 05:15 — 13.12.12

Re: HP Officejet Pro 8500A error 0005FBB6

Сервис-центр СКАН » 14:39 — 14.12.12

Re: HP Officejet Pro 8500A error 0005FBB6

stranger » 10:52 — 15.12.12

Re: HP Officejet Pro 8500A error 0005FBB6

Сервис-центр СКАН » 12:16 — 15.12.12

В мануале по HP при такой ошибке ещё рекомендуют сделать следующее:
1. Включить принтер.
2. Отсоединить USB кабель.
3. Вытащить картриджи из принтера.
4. Выдернуть шнур питания.
5. Подождать 60 секунд.
6. Подключить шнур питания. Если принтер сам не начнет грузиться, нажать кнопку питания.
7. Установить картриджи и закрыть все крышки.
8. Если запросит печать страницы калибровки, выполнить её.
9. Подсоединить USB и попробовать произвести печать.
10. Если не помогает, на этом они рекомендуют обратиться в сервис HP.

Если не поможет, то можно ещё попробовать перезагрузить NVRAM:
1. Включить принтер.
2. Отсоединить USB.
3. При работающем принтере выдернуть шнур питания.
4. Нажать и удерживать кнопки # и 3 одновременно.
5. Удерживая кнопки # и 3 подключить кабель питания. пока идет процесс загрузки (мигает кнопка питания).
6. Дальше следую инструкциям установить новые настройки. (т.к. все будет сброшено).
7. Если работать не начнет попробовать заменить картриджи с чернилами.

Если и это не поможет, думаю лучше уже нести к сервисникам в HP.

Re: HP Officejet Pro 8500A error 0005FBB6

stranger » 12:20 — 17.12.12

Re: HP Officejet Pro 8500A error 0005FBB6

Сервис-центр СКАН » 12:34 — 17.12.12

Re: HP Officejet Pro 8500A error 0005FBB6

stranger » 13:13 — 17.12.12

  • Похожие темы Ответы Просмотры Последнее сообщение
  • HP1300 ошибка: Fuser error. The fuser has a malfunction.
    fikus в форуме HEWLETT PACKARD (HP) 12 5809 fikus
    23:23 — 23.10.11
  • Лазерный принтер Brother HL-2030 — Error «Paper» останавливается бумага при начале печати.
    simatic в форуме BROTHER 6 17405 человек
    10:57 — 31.01.07
  • Canon BJC-6500 выдают «BJ Cartridge error»
    Егоров М.Н. в форуме Струйные принтеры 1 2930 tishka
    00:43 — 19.06.09
  • МФУ Epson RX500 пишет error и «обраитесь к докуметации»
    Светланка в форуме EPSON 2 2763 Светланка
    15:09 — 18.11.11
  • Копир Xerox WorkCentre 312 — «Open heat error»
    в форуме XEROX 3 12542 vo_van
    15:26 — 16.05.11

Кто сейчас на конференции

Сейчас этот форум просматривают: нет зарегистрированных пользователей и гости: 4

Источник

Error code 0x0005fbb6 lib math c

‎10-17-2022 07:24 AM — last edited on ‎10-19-2022 07:44 AM by Ric_ob

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

Error code: 0X0005FBB6 LIB_MATH C

‎10-24-2022 12:26 PM

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

I’ve tried everything to clear this error code seems like HP should have a solution since they have a code!

My Office jet 4650 shows error code 0X0005FBB6 whenever I try to make copies or try to scan both from app and directly from Printer. Everything else seems to work ie. test pages, cartridge alignment, wireless print jobs just can not copy or scan 😫

‎10-26-2022 10:42 AM

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

Welcome to the HP Support Community

I understand you are getting an error message 0X0005FBB6 LIB_MATH C on your HP DeskJet Ink Advantage 4535 Printer . Not to worry I will help you to get a resolution to resolve the issue.

We need to perform a Semi full reset to restore the printer back to its original settings.

The reset instructions are specific for your printer and performing those steps on a different printer may brick the device.

I’ve sent you a private message with reset instructions, follow the reset instruction to perform a full reset and re-initialize the printer.

In order to access your private messages, click the private message icon on the upper right corner of your HP Community profile, next to your profile Name or simply click on this link .

Hope this helps! Keep me posted.

Please click “ Accepted Solution ” if you feel my post solved your issue, it will help others find the solution. Click the “ Kudos/Thumbs Up » on the bottom right to say “ Thanks ” for helping!

ANAND_ANDY
I am an HP Employee

Источник

Error code 0x0005fbb6 lib math c

‎01-21-2018 09:50 AM

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

scanner wont scan keeps giving me a error code 0x0005fbb6

‎01-22-2018 05:19 PM

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

Welcome to the HP Forums, this is a great location to get assistance! I read your post and see that you are getting error code 0x0005fbb6. I would like to help you resolve this issue.

However, I will need a few details to provide an accurate solution,

  • When did this issue start?
  • Did you do any hardware or software changes?
  • How is the printer connected to computer, wired or wireless?

Perform a power reset

  1. Turn on the printer, if it is not already on.
  2. Wait until the printer is idle and silent before you continue.
  3. With the printer turned on , disconnect the power cord from the rear of the printer.
  4. Wait at least 30 seconds.
  5. Reconnect the power cord to the rear of the printer.
  6. Turn on the printer

Reply with the result of the above-mentioned steps, for further assistance.

Sandytechy20
I am an HP Employee

‎01-24-2018 01:15 AM

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

‎01-24-2018 12:13 PM

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

Thanks for the reply.

I appreciate your time and effort.

Eager to know, did you get time to perform power reset in the printer.

If not, follow the below steps:

  1. Turn on the printer, if it is not already on.
  2. Wait until the printer is idle and silent before you continue.
  3. With the printer turned on , disconnect the power cord from the rear of the printer.
  4. Wait at least 30 seconds.
  5. Reconnect the power cord to the rear of the printer.
  6. Turn on the printer.

If the issue persists, Update the printer firmware.

Click here and refer the document to update the printer firmware.

Let me know how it goes.

Sandytechy20
I am an HP Employee

‎01-24-2018 05:09 PM

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

To correct error 0x0005fbb6, try the following :

  • Uninstall the existing printer driver
  • Disconnect the USB cable and disconnect the power cable from your printer and the AC outlet
  • Download the latest driver on the HP website
  • Start the driver installation
  • Reconnect the cables when the installation process tells you to.

If the above procedure doesn’t do the trick, try the following:

  • With the Printer on, disconnect the USB cable.
  • Remove the ink cartridges
  • Wait about 10 seconds then disconnect the power cord from the printer and AC outlet
  • Wait approximately 1 minute then reconnect the power cord to the printer and the AC outlet
  • If the printer doesn’t turn on, press the power button to turn it on.
  • Reinstall the ink cartridges and close the door.
  • Reconnect the USB cable.

If neither of thes two procedures work, then reset to factory defaults as follows:

  • Go to «Setup»
  • Select «Tools»
  • Select «Restore Factory Defaults»
  • Power your printer down then turn it back on.

Источник

Error code 0x0005fbb6 lib math c

‎07-02-2022 08:15 AM

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

i’m getting 0x0005FBB6 when i switch on my hp officejet 3830 printer.

I tried all below suggested steps multiple times but that’s not helping

Remove the ink cartridges, and reset the printer

Remove the ink cartridges from the printer.

With the printer turned on , disconnect the power cord from the printer.

Unplug the power cord from the power source.

Wait at least 60 seconds.

Reconnect the power cord to a wall outlet and to the printer.

HP recommends plugging the printer directly into a wall outlet.

Turn the printer on.

Reinsert the ink cartridges, and then close the ink cartridge access door.

‎07-05-2022 05:20 AM

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

Thank you for posting on the HP Support Community.

Don’t worry as I’ll be glad to help,

I appreciate your efforts to try and resolve the issue.
This seems like a hardware issue with the printer. Let’s check for any paper jams inside the printer and make sure the printer carriage is moving freely.

Refer to the steps mentioned in this document — Paper Jam Error

If the error persists, I’m sending out a private message to assist you with the next course of action. Please check your Private message icon on the upper right corner of your HP Community profile Next, to your profile Name, you should see a little blue envelope, please click on it or simply click on this link: https://h30434.www3.hp.com/t5/notes/privatenotespage

Hope this helps! Keep me posted for further assistance.
Please click “ Accept as Solution ” if you feel my post solved your issue, it will help others find the solution. Click the “Kudos, Thumbs Up» on the bottom right to say “Thanks” for helping!

Источник

Error code 0x0005fbb6 lib math c

‎01-09-2013 01:52 PM

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

My printer all of sudden displays the 0005FBB6 and blue screen. I have tried the hard reset. Nothing. What can I do?

‎12-27-2013 07:01 PM

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

Its wifi connection error. It would be good if HP could fix this with new firmware.

‎01-09-2013 02:13 PM

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

What model is the printer? And is it 0005FBB6 or 0x05FBB6 that is displayed?

I was a support engineer for HP.

If the advice resolved the situation, please mark it as a solution. Thank you.

‎01-09-2013 02:17 PM

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

Model 8500A Pro premium

The error code is 0005FBB6

‎04-04-2013 03:25 PM

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

Please help my P C S HP C6380 shows a blue screen and very briefly 0005FBB6 the printer then asks to be switched off and on again and an orange light, on light and print photos lights flash. what dose this mean?

‎12-05-2013 07:53 AM

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

Excuse me, where is the solution? I do not see anywhere around. I just bought the Photosmart 6520 series and this is only the fourth day of use.

There was a paper jam which I cleared. Now it is not working, asking me to turn off and then on again. When I did that, it started and then this message 0005FBB6 flash for a moment and then I was asked to turn off and then on again. This happens over and over again. Please help.

Источник

Источник

How to fix error code 0005fbb6 on HP printers

Solution 1 for error 0005fbb6:

  • Uninstall the printer driver
  • Disconnect the USB cable and the power from the printer
  • Donwload the last driver on the HP website
  • Install the driver
  • Reconnect the cables when the program tells to do.

Solution 2: reset the printer

  • Printer on, disconnect the USB cable.
  • Remove the cartridges
  • Wait for 10 seconds and disconnect the power cord
  • Wait for 60 seconds.
  • Reconnect the power cord
  • If the printer do not turn on, press the power button.
  • Insert the cartridges and close the door.
  • Reconect the USB cable.

Solution 3:

  • Go to «Setup», then «Tools» and «Restore Factory Defaults»
  • Power off and on.

Popular posts from this blog

The error B204 could happen after a cartridge replacement. First of all, when installing, remove the cartridges from the plastic package, but do not drill any plastic membranes, as this will cause this error when placing the cartridge. The error may also appear if you change a completely empty cartridge: when installing a full cartridge, the printer enters a cleaning cycle, but the printhead has not yet received ink from the newly inserted cartridge. Here are some tips to cancel this error B204:: Solution 1: Remove the cartridges Power the printer for 2 minutes Switch on the printer Install the cartrdiges Solution 2: Switch on the printer Unplug  the power cable Open the cover Move the print head carriage manually to the usual place where it goes for the cartridge change (If the printhead carriage is not movable, reconnect and then turn on the printer, then unplug it again when the head carriage is in the moving position). Change the cartridges. Close the fr

MAJ11/06/17 Error B200 means the printhead voltage or temperature is not normal. The Printhead could be defective…. but first, try these solutions below: Solution 1 : Disconnect the power cable from the printer. Wait 1 hour. Connect the power cable Solution 2 : Check and Clean Head contact pin condition of the carriage unit Check Cable connection especially the carriage FFC Solution 3 : Turn off the power Open the panel Turn on the power Wait for print carriage to start moving to the left. Let it go past half way Before print carriage reaches left hand side shut the cover. Leave the Printer turned on Solution 4 : Unplug the power cable. Open the printer Push the whole print head mechanic to the center While the printer still open, plug the power and turn it ON.  When the printhead still moving and is going to the very LEFT, close the cover.  Wait until its boot up.  Solution 4a: Take out all of the ink cartridges Lift up the gr

MAJ 25/08/17 The Service Tool V3400 allow to reset the counter of some Canon printers. For the error code 006 , try this : Solution 1: Check your cartridges: an empty cartridge can lead to error 006 Solution 2 : After you avec clicked on «Main», wait a few minutes.  If the error still here, restarts the Service Tool Solution 3 : Close the service tool Disconnect the USB cable from the printer After 10 seconds, plug back the cable to the printer On Windows, click next when appears «New device» Open the service tool

Источник

HP Printers are one of the best printers worldwide. They keep on inventing and reinventing their products to astonish their customers every time they launch their latest versions. The printers are demanding due to quality and advanced technology. Officejet pro printers can add up to 5 people at a time and provide a secured printing mechanism. With a lot of new specifications added, the question arises, How to fix HP Officejet 3830 Error Code 0×0005fbb6?

Every problem that arises within a printer can be solved with patience and following some guidelines. This particular error message pops up on your screen while you try to print something. A blue screen with the error code message appears. Let’s see How to fix HP Officejet 3830 Error Code 0×0005fbb6 by considering the following steps.

Step – 1 Check the error code.

  • If the error code is displayed with an error description then the following steps mentioned in the article will not work. But if the message contains only the error code then follow the next step.

Step – 2 You need to reset the printer

  • This step will be followed to remove printer failure errors.
  • Disconnect the power cord from the printer, while keeping it turned on.
  • Then remove the power cord from the power source. And wait for sixty seconds.
  • Reconnect the cord to the power source and the printer.
  • Check if the error is resolved or not. If not follow the next step.

Step – 3 Further remove the ink cartridges and then follow up with printer resetting.

  • Remove the ink cartridges.
  • Next, follow the entire process as mentioned in step 2
  • After reconnecting the power cord to the printer and the power source, turn on the printer.
  • Open the ink cartridge access door, reinsert the ink cartridges and then close the door properly.
  • You may receive a pop-up message asking you to print a calibration or assignment page.
  • Follow the message. If you receive the same error code again, go through the next step.

Step – 4 Go for servicing

  • After completion of all the preceding steps, if the question How to fix HP Officejet 3830 Error Code 0×0005fbb6 persists, then go for servicing or replacing your HP Officejet 3830 printer.

Two more steps you can consider –

  1. Reinstallation of drivers
  2. Uninstall the printer drivers
  3. Then disconnect the power cord and USB cable from the printer.
  4. From the company website download the latest driver and install it.
  5. The installation process will ask you to reconnect the cords. Follow the message.
  1. Restore factory defaults
  2. From “Setup” tab, go to “Tools” and select ”Restore Factory Defaults”
  3. Turn off the power source and turn it on.
  4. Check if the error is resolved or not.

If troubleshooting an error is relatively harder than you imagined and you are not confident enough then take expert help. Before going to some other experts check your product’s warranty status. If it is within the warranty period then the company will charge you almost no fees.

Источник

HP Officejet Pro 8500A error 0005FBB6

День добрый всем!
подскажите что за ошибка 0005FBB6 высвечивается на принтере при включении? Варианты сброса?

stranger
новичок
 
Сообщения: 22
Зарегистрирован: 09:47 — 31.07.12
Баллы репутации: 0

Re: HP Officejet Pro 8500A error 0005FBB6

Непрочитанное сообщение stranger » 09:20 — 11.12.12

Сервис-центр СКАН писал(а):Это ошибка юстировки… сброса варианта насколько я понимаю нет… это надо разбирать сканер и хорошенько все чистить.

понял, займусь разборкой чисткой…спс

stranger
новичок
 
Сообщения: 22
Зарегистрирован: 09:47 — 31.07.12
Баллы репутации: 0

Re: HP Officejet Pro 8500A error 0005FBB6

Непрочитанное сообщение stranger » 05:15 — 13.12.12

Разобрал, почистил, собрал и ничего не изменилось. Включал со сканером и без сканера -пишет ту же ошибку (по идее должен материться без сканера, что сканер не подключен).При включении ни происходит ни какого движения сканера изначально…должен же он сперва тест пройти и сканера и принтера, есть соображения в чем дело?

stranger
новичок
 
Сообщения: 22
Зарегистрирован: 09:47 — 31.07.12
Баллы репутации: 0

Re: HP Officejet Pro 8500A error 0005FBB6

Непрочитанное сообщение Сервис-центр СКАН » 12:16 — 15.12.12

В мануале по HP при такой ошибке ещё рекомендуют сделать следующее:
1. Включить принтер.
2. Отсоединить USB кабель.
3. Вытащить картриджи из принтера.
4. Выдернуть шнур питания.
5. Подождать 60 секунд.
6. Подключить шнур питания. Если принтер сам не начнет грузиться, нажать кнопку питания.
7. Установить картриджи и закрыть все крышки.
8. Если запросит печать страницы калибровки, выполнить её.
9. Подсоединить USB и попробовать произвести печать.
10. Если не помогает, на этом они рекомендуют обратиться в сервис HP.

Если не поможет, то можно ещё попробовать перезагрузить NVRAM:
1. Включить принтер.
2. Отсоединить USB.
3. При работающем принтере выдернуть шнур питания.
4. Нажать и удерживать кнопки # и 3 одновременно.
5. Удерживая кнопки # и 3 подключить кабель питания… пока идет процесс загрузки (мигает кнопка питания).
6. Дальше следую инструкциям установить новые настройки. (т.к. все будет сброшено).
7. Если работать не начнет попробовать заменить картриджи с чернилами.

Если и это не поможет, думаю лучше уже нести к сервисникам в HP.

Аватара пользователя
Сервис-центр СКАН
Помощник админа Консультант
 
Сообщения: 966
Зарегистрирован: 14:11 — 28.02.05
Откуда: Москва, м. Таганская
Баллы репутации: 1
  • Сайт

Re: HP Officejet Pro 8500A error 0005FBB6

Непрочитанное сообщение stranger » 12:20 — 17.12.12

кнопки на МФУ сенсорные соответственно давить на стекло без активности оных нет смысла..все вышеуказанные инструкции проделал….ни чего не изменилось в поведении МФУ, все так же высвечивает 0005FBB6, как только подключаешь к сети или нажмешь на кнопку вкл. Даже попыток шевельнуть головой или сканером (лампа не горитт и не пытается), полный труп…думаю проблемы с платой форматора…если уж даже сеть не работает (при подключении его к пк — он не обнаруживается ни с установленным ПО на МФУ ни без установленных драйверов подключал к разным ПК с разными системами ОС XP. W7)

stranger
новичок
 
Сообщения: 22
Зарегистрирован: 09:47 — 31.07.12
Баллы репутации: 0

Вернуться в HEWLETT PACKARD (HP)

Кто сейчас на конференции

Сейчас этот форум просматривают: нет зарегистрированных пользователей и гости: 9

Источник

Содержание

  1. Error code 0x0005fbb6 lib math c
  2. Error code 0x0005fbb6 lib math c
  3. Error code 0x0005fbb6 lib math c
  4. Error code 0x0005fbb6 lib math c
  5. Error code 0x0005fbb6 lib math c

Error code 0x0005fbb6 lib math c

‎01-21-2018 09:50 AM

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

scanner wont scan keeps giving me a error code 0x0005fbb6

‎01-22-2018 05:19 PM

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

Welcome to the HP Forums, this is a great location to get assistance! I read your post and see that you are getting error code 0x0005fbb6. I would like to help you resolve this issue.

However, I will need a few details to provide an accurate solution,

  • When did this issue start?
  • Did you do any hardware or software changes?
  • How is the printer connected to computer, wired or wireless?

Perform a power reset

  1. Turn on the printer, if it is not already on.
  2. Wait until the printer is idle and silent before you continue.
  3. With the printer turned on , disconnect the power cord from the rear of the printer.
  4. Wait at least 30 seconds.
  5. Reconnect the power cord to the rear of the printer.
  6. Turn on the printer

Reply with the result of the above-mentioned steps, for further assistance.

Sandytechy20
I am an HP Employee

‎01-24-2018 01:15 AM

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

‎01-24-2018 12:13 PM

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

Thanks for the reply.

I appreciate your time and effort.

Eager to know, did you get time to perform power reset in the printer.

If not, follow the below steps:

  1. Turn on the printer, if it is not already on.
  2. Wait until the printer is idle and silent before you continue.
  3. With the printer turned on , disconnect the power cord from the rear of the printer.
  4. Wait at least 30 seconds.
  5. Reconnect the power cord to the rear of the printer.
  6. Turn on the printer.

If the issue persists, Update the printer firmware.

Click here and refer the document to update the printer firmware.

Let me know how it goes.

Sandytechy20
I am an HP Employee

‎01-24-2018 05:09 PM

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

To correct error 0x0005fbb6, try the following :

  • Uninstall the existing printer driver
  • Disconnect the USB cable and disconnect the power cable from your printer and the AC outlet
  • Download the latest driver on the HP website
  • Start the driver installation
  • Reconnect the cables when the installation process tells you to.

If the above procedure doesn’t do the trick, try the following:

  • With the Printer on, disconnect the USB cable.
  • Remove the ink cartridges
  • Wait about 10 seconds then disconnect the power cord from the printer and AC outlet
  • Wait approximately 1 minute then reconnect the power cord to the printer and the AC outlet
  • If the printer doesn’t turn on, press the power button to turn it on.
  • Reinstall the ink cartridges and close the door.
  • Reconnect the USB cable.

If neither of thes two procedures work, then reset to factory defaults as follows:

  • Go to «Setup»
  • Select «Tools»
  • Select «Restore Factory Defaults»
  • Power your printer down then turn it back on.

Источник

Error code 0x0005fbb6 lib math c

‎01-09-2013 01:52 PM

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

My printer all of sudden displays the 0005FBB6 and blue screen. I have tried the hard reset. Nothing. What can I do?

‎12-27-2013 07:01 PM

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

Its wifi connection error. It would be good if HP could fix this with new firmware.

‎01-09-2013 02:13 PM

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

What model is the printer? And is it 0005FBB6 or 0x05FBB6 that is displayed?

I was a support engineer for HP.

If the advice resolved the situation, please mark it as a solution. Thank you.

‎01-09-2013 02:17 PM

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

Model 8500A Pro premium

The error code is 0005FBB6

‎04-04-2013 03:25 PM

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

Please help my P C S HP C6380 shows a blue screen and very briefly 0005FBB6 the printer then asks to be switched off and on again and an orange light, on light and print photos lights flash. what dose this mean?

‎12-05-2013 07:53 AM

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

Excuse me, where is the solution? I do not see anywhere around. I just bought the Photosmart 6520 series and this is only the fourth day of use.

There was a paper jam which I cleared. Now it is not working, asking me to turn off and then on again. When I did that, it started and then this message 0005FBB6 flash for a moment and then I was asked to turn off and then on again. This happens over and over again. Please help.

Источник

Error code 0x0005fbb6 lib math c

‎10-17-2022 07:24 AM — last edited on ‎10-19-2022 07:44 AM by Ric_ob

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

Error code: 0X0005FBB6 LIB_MATH C

‎10-24-2022 12:26 PM

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

I’ve tried everything to clear this error code seems like HP should have a solution since they have a code!

My Office jet 4650 shows error code 0X0005FBB6 whenever I try to make copies or try to scan both from app and directly from Printer. Everything else seems to work ie. test pages, cartridge alignment, wireless print jobs just can not copy or scan

‎10-26-2022 10:42 AM

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

Welcome to the HP Support Community

I understand you are getting an error message 0X0005FBB6 LIB_MATH C on your HP DeskJet Ink Advantage 4535 Printer . Not to worry I will help you to get a resolution to resolve the issue.

We need to perform a Semi full reset to restore the printer back to its original settings.

The reset instructions are specific for your printer and performing those steps on a different printer may brick the device.

I’ve sent you a private message with reset instructions, follow the reset instruction to perform a full reset and re-initialize the printer.

In order to access your private messages, click the private message icon on the upper right corner of your HP Community profile, next to your profile Name or simply click on this link .

Hope this helps! Keep me posted.

Please click “ Accepted Solution ” if you feel my post solved your issue, it will help others find the solution. Click the “ Kudos/Thumbs Up » on the bottom right to say “ Thanks ” for helping!

Источник

Error code 0x0005fbb6 lib math c

‎12-30-2021 02:10 PM

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

Started off with Error Code 0X0005FBB6 LIB_MATH C. Eventually managed to clear that (following steps outlined in document https://h30434.www3.hp.com/t5/Printing-Errors-or-Lights-Stuck-Print-Jobs/Error-Code-0X0005FBB6/td-p/. ). Having had to manually move the cartridge holder in order to remove (and then reinstall) the cartridges, when turning the printer back on, it is now stuck on «checking cartridges» (they are HP instant ink cartridges).

I don’t know whether this is related to the above, but recently the printer will not double-side print, even though that is set in the options?

The printer is out of warranty, and I don’t have the funds to get it serviced, so any help would be gratefully received.

‎01-03-2022 07:55 AM

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

I’d like to help!

I understand that the printer is stuck on the «checking cartridge» message.

Follow the steps to resolve the issue-

Reset the printer

Reset the printer to recover from printer errors or failures.

  1. If your printer has a rechargeable battery, remove it.

  1. With the printer turned on , disconnect the power cord from the printer.

  1. Unplug the power cord from the power source.
  2. Wait 60 seconds.
  3. Reconnect the power cord to a wall outlet and to the printer.
    NOTE:
    HP recommends plugging the printer directly into a wall outlet.
  4. Turn on the printer to complete the reset.

Clean the ink cartridge and carriage electrical contacts

Remove any debris or buildup from the contacts on the cartridges and in the carriage.

Open the door or lid to the cartridge access area. Wait until the carriage stops moving before continuing.

Remove the cartridge indicated in the error message from the carriage.

Carriages with cartridge latches: Open the latch, and then pull the cartridge up and out of the slot.

Carriages without cartridge latches: Gently press down on the cartridge to release it, and then pull it out of the slot.

Holding the cartridge by the sides, remove any protective tape that still might be on the contacts.

Do not touch the ink nozzles or the copper-colored electrical strip. Touching or trying to remove these parts can result in clogs, ink failure, and bad electrical connections.

Lightly dampen a lint-free cloth with distilled water, and then wipe the copper-colored contacts on the cartridge.

Lightly dampen a lint-free cloth or swab with distilled water, and then clean the electrical contacts in the carriage.

Wait 10 minutes for the contacts to dry, and then reinsert the cartridge into its color-coded slot.

Repeat these steps for the other cartridge if it was indicated in the error message.

Close the door or lid to the cartridge access area.

If the error persists, clean the cartridge and carriage contacts a second time.

Try the single-cartridge mode

The printer you own can work in single-cartridge mode, wherein the printer will be able to print with one cartridge in the printer. Which will help us identify if its a cartridge issue or a printhead issue

To try single-cartridge mode follow the below steps:

  • remove the black ink from the printer, leave the color in and try printing
  • then remove the color ink and, insert the black in and try printing

Please send us a private message with your Instant Ink account details or you may also respond to the private message I’ve sent out and I’ll help you out, accordingly. Check next to your profile name, you should see a little blue envelope, please click on it.

Hope this helps! Keep me posted.

And, Welcome to the HP Support Community.

Please click “ Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.

Click the “Yes» on the bottom right to say “ Tha nks ” fo r helping

Источник

Error code 0x0005fbb6 lib math c

‎07-02-2022 08:15 AM

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

i’m getting 0x0005FBB6 when i switch on my hp officejet 3830 printer.

I tried all below suggested steps multiple times but that’s not helping

Remove the ink cartridges, and reset the printer

Remove the ink cartridges from the printer.

With the printer turned on , disconnect the power cord from the printer.

Unplug the power cord from the power source.

Wait at least 60 seconds.

Reconnect the power cord to a wall outlet and to the printer.

HP recommends plugging the printer directly into a wall outlet.

Turn the printer on.

Reinsert the ink cartridges, and then close the ink cartridge access door.

‎07-05-2022 05:20 AM

  • Mark as New
  • Bookmark
  • Subscribe
  • Permalink
  • Print
  • Flag Post

Thank you for posting on the HP Support Community.

Don’t worry as I’ll be glad to help,

I appreciate your efforts to try and resolve the issue.
This seems like a hardware issue with the printer. Let’s check for any paper jams inside the printer and make sure the printer carriage is moving freely.

Refer to the steps mentioned in this document — Paper Jam Error

If the error persists, I’m sending out a private message to assist you with the next course of action. Please check your Private message icon on the upper right corner of your HP Community profile Next, to your profile Name, you should see a little blue envelope, please click on it or simply click on this link: https://h30434.www3.hp.com/t5/notes/privatenotespage

Hope this helps! Keep me posted for further assistance.
Please click “ Accept as Solution ” if you feel my post solved your issue, it will help others find the solution. Click the “Kudos, Thumbs Up» on the bottom right to say “Thanks” for helping!

Источник

Источник

Понравилась статья? Поделить с друзьями:

Читайте также:

  • Error code 0x0003 geforce experience что это win 10
  • Error code 0x000135
  • Error code 0x0000605
  • Error code 0x0000428 windows 10
  • Error code 0x000035a

    • 0 0 голоса
    Рейтинг статьи
    Подписаться
    Уведомить о
    guest

    0 комментариев
    Старые
    Новые Популярные
    Межтекстовые Отзывы
    Посмотреть все комментарии