everyone. I am compiling DCMTK 3.6.1 in Visual Studio 2013. My OS is Windows 8. I also used CMake 3.2.3. I have already successfully compiled both x64 versions of debug and release for the ALL_BUILD project. However, for the INSTALL project, I can’t compile it because the following error occurs:
Error 1 error MSB3073: The command "setlocal
"C:Program Files (x86)CMakebincmake.exe" -DBUILD_TYPE=Release -P cmake_install.cmake
if %errorlevel% neq 0 goto :cmEnd
:cmEnd
endlocal & call :cmErrorLevel %errorlevel% & goto :cmDone
:cmErrorLevel
exit /b %1
:cmDone
if %errorlevel% neq 0 goto :VCEnd
:VCEnd" exited with code 1. C:Program Files (x86)MSBuildMicrosoft.Cppv4.0V120Microsoft.CppCommon.targets 132
According to this link, I need admin rights. But I am already running Visual Studio in Admin mode. Can someone please enlighten me on what I might be doing wrong? Thank you very much!
asked Jul 16, 2015 at 14:37
2
What about specifying another value for CMAKE_INSTALL_PREFIX in the CMake GUI? That means, a directory where you definitely have write access.
answered Jul 23, 2015 at 12:57
J. RiesmeierJ. Riesmeier
1,5849 silver badges14 bronze badges
3
This is an old post, but I encountered the same problem when I attempted to install OpenCV for Windows 10 using VS 16 2019 in a folder close to the root of C:.
Solution: Open cmd as administrator, open the SLN-project (In my case <OpenCV.sln>), and run Build on INSTALL. That worked like a charm.
answered Jan 7, 2021 at 15:10
0
This is a simple 2 step fix.
First step is to remove the Read Only folder property. To do this, just go wherever you cloned the software you want to build, right click on the containing folder and uncheck the Read Only checkmark.
Second step is to exit visual studio and start terminal as administrator/with sudo privileges if on linux/mac. Navigate to the build folder and type the solution name. This will open up VC with admin privileges.
This fixed the problem for me.
answered May 19, 2020 at 8:41
DimitarDimitar
8876 silver badges24 bronze badges
1
Just open a prompt and run «C:Program Files (x86)CMakebincmake.exe» -DBUILD_TYPE=Release -P cmake_install.cmake (or similar showed in VS error list) and see where is the problem
in my case the problem was samples were not compiled, so i entered in modules directory and compile manually each module necessary.
After compile the module i run the command again and see what happen, repeat until solve the problem
answered Aug 16, 2021 at 20:14
the best solution;
CMAKE_INSTALL_PREFIX
if you choose realease/debug then after CMake configure by CMake on the same mood.
just try
answered Apr 13, 2022 at 3:33
I had a similar error, if you can check that there are no spaces or character symbols in your path. FOr example I had a directory with the file name ‘ABC&D’ and by removing & the error was fixed.
This coupled with allowing admin rights should be an attempt to fix the problem.
answered Jun 28, 2022 at 15:46
- Remove From My Forums
-
Question
-
The command «setlocal»C:Program Files (x86)CMake 2.8bincmake.exe» -DBUILD_TYPE=Debug –P cmake_install.cmake if %errorlevel% neq 0 goto :cmEnd :cmEnd endlocal
& call :cmErrorLevel %errorlevel% & goto :cmDone :cmErrorLevel exit /b %1 :cmDone if %errorlevel% neq 0 goto :VCEnd
:VCEnd» exited with code 1.This is the text from my build output. I am trying to build a project called INSTALL. A more detailed error report is below. Any help is appreciated. As stated above, my build is getting code MSB3073 and
exiting with code 1.1>—— Build started: Project: INSTALL, Configuration: Debug x64 ——
1> — Install configuration: «Debug»
1> CMake Error at cmake_install.cmake:31 (FILE):
1> file cannot create directory: C:/Program Files/Arcemu/.. Maybe need
1> administrative privileges.
1>
1>
1>C:Program Files (x86)MSBuildMicrosoft.Cppv4.0Microsoft.CppCommon.targets(113,5): error MSB3073: The command «setlocal
1>C:Program Files (x86)MSBuildMicrosoft.Cppv4.0Microsoft.CppCommon.targets(113,5): error MSB3073: «C:Program Files (x86)CMake 2.8bincmake.exe» -DBUILD_TYPE=Debug -P cmake_install.cmake
1>C:Program Files (x86)MSBuildMicrosoft.Cppv4.0Microsoft.CppCommon.targets(113,5): error MSB3073: if %errorlevel% neq 0 goto :cmEnd
1>C:Program Files (x86)MSBuildMicrosoft.Cppv4.0Microsoft.CppCommon.targets(113,5): error MSB3073: :cmEnd
1>C:Program Files (x86)MSBuildMicrosoft.Cppv4.0Microsoft.CppCommon.targets(113,5): error MSB3073: endlocal & call :cmErrorLevel %errorlevel% & goto :cmDone
1>C:Program Files (x86)MSBuildMicrosoft.Cppv4.0Microsoft.CppCommon.targets(113,5): error MSB3073: :cmErrorLevel
1>C:Program Files (x86)MSBuildMicrosoft.Cppv4.0Microsoft.CppCommon.targets(113,5): error MSB3073: exit /b %1
1>C:Program Files (x86)MSBuildMicrosoft.Cppv4.0Microsoft.CppCommon.targets(113,5): error MSB3073: :cmDone
1>C:Program Files (x86)MSBuildMicrosoft.Cppv4.0Microsoft.CppCommon.targets(113,5): error MSB3073: if %errorlevel% neq 0 goto :VCEnd
1>C:Program Files (x86)MSBuildMicrosoft.Cppv4.0Microsoft.CppCommon.targets(113,5): error MSB3073: :VCEnd» exited with code 1.
========== Build: 0 succeeded, 1 failed, 0 up-to-date, 0 skipped ==========
Answers
-
Seems pretty self explanatory to me.
1> CMake Error at cmake_install.cmake:31 (FILE):
1> file cannot create directory: C:/Program Files/Arcemu/.. Maybe need
1> administrative privileges.
1>
Line 31 of cmake_install.cmake tries to create a file in «c:program files». It fails (probably because it doesn’t have admin rights, and you need to be elevated to write to c:program files.
Either modify the make file so that it doesn’t try to write to which it does not have write access, or modify the way you are launching the program so that it does have write access to that folder.
-
Marked as answer by
Tuesday, November 20, 2012 1:04 PM
-
Marked as answer by
This is a continuation from: #2
Have downloaded latest develop branch. Generated with CMake for VS2013 using settings ENABLE_SHARED_LIBRARIES and ENABLE_TESTS.
After building (the ALL_BUILD project) I believe I need to build the INSTALL project in VS2013.
However this produces:
——- Rebuild All started: Project: INSTALL, Configuration: Release Win32 ——
—Install configuration: «Release»
CMake Error at ATK/cmake_install.cmake:39 (file):
file cannot create directory: C:/Program Files (x86)/AudioTK/include/ATK.
Maybe need administrative privileges.
Call Stack (most recent call first):
cmake_install.cmake:32 (include)
Followed by an error:
Error 1 error MSB3073: The command «setlocal «C:Program Files (x86)CMakebincmake.exe» -DBUILD_TYPE=Release -P cmake_install.cmake if %errorlevel% neq 0 goto :cmEnd :cmEnd endlocal & call :cmErrorLevel %errorlevel% & goto :cmDone :cmErrorLevel exit /b %1 :cmDone if %errorlevel% neq 0 goto :VCEnd :VCEnd» exited with code 1. C:Program Files (x86)MSBuildMicrosoft.Cppv4.0V120Microsoft.CppCommon.targets 132 5 INSTALL
Running VS2013 with administrative privileges doesn’t help.
Содержание
- Error msb3073 microsoft cppcommon targets
- Answered by:
- Question
- Error msb3073 microsoft cppcommon targets
- Asked by:
- Question
- All replies
- ошибка MSB3073: как мне это исправить?
- 6 ответов
- Error msb3073 microsoft cppcommon targets
- Answered by:
- Question
- Answers
Error msb3073 microsoft cppcommon targets
This forum has migrated to Microsoft Q&A. Visit Microsoft Q&A to post new questions.
Answered by:
Question
The command «setlocal»C:Program Files (x86)CMake 2.8bincmake.exe» -DBUILD_TYPE=Debug –P cmake_install.cmake if %errorlevel% neq 0 goto :cmEnd :cmEnd endlocal & call :cmErrorLevel %errorlevel% & goto :cmDone :cmErrorLevel exit /b %1 :cmDone if %errorlevel% neq 0 goto :VCEnd :VCEnd» exited with code 1.
This is the text from my build output. I am trying to build a project called INSTALL. A more detailed error report is below. Any help is appreciated. As stated above, my build is getting code MSB3073 and exiting with code 1.
1>—— Build started: Project: INSTALL, Configuration: Debug x64 ——
1> — Install configuration: «Debug»
1> CMake Error at cmake_install.cmake:31 (FILE):
1> file cannot create directory: C:/Program Files/Arcemu/.. Maybe need
1> administrative privileges.
1>C:Program Files (x86)MSBuildMicrosoft.Cppv4.0Microsoft.CppCommon.targets(113,5): error MSB3073: The command «setlocal
1>C:Program Files (x86)MSBuildMicrosoft.Cppv4.0Microsoft.CppCommon.targets(113,5): error MSB3073: «C:Program Files (x86)CMake 2.8bincmake.exe» -DBUILD_TYPE=Debug -P cmake_install.cmake
1>C:Program Files (x86)MSBuildMicrosoft.Cppv4.0Microsoft.CppCommon.targets(113,5): error MSB3073: if %errorlevel% neq 0 goto :cmEnd
1>C:Program Files (x86)MSBuildMicrosoft.Cppv4.0Microsoft.CppCommon.targets(113,5): error MSB3073: :cmEnd
1>C:Program Files (x86)MSBuildMicrosoft.Cppv4.0Microsoft.CppCommon.targets(113,5): error MSB3073: endlocal & call :cmErrorLevel %errorlevel% & goto :cmDone
1>C:Program Files (x86)MSBuildMicrosoft.Cppv4.0Microsoft.CppCommon.targets(113,5): error MSB3073: :cmErrorLevel
1>C:Program Files (x86)MSBuildMicrosoft.Cppv4.0Microsoft.CppCommon.targets(113,5): error MSB3073: exit /b %1
1>C:Program Files (x86)MSBuildMicrosoft.Cppv4.0Microsoft.CppCommon.targets(113,5): error MSB3073: :cmDone
1>C:Program Files (x86)MSBuildMicrosoft.Cppv4.0Microsoft.CppCommon.targets(113,5): error MSB3073: if %errorlevel% neq 0 goto :VCEnd
1>C:Program Files (x86)MSBuildMicrosoft.Cppv4.0Microsoft.CppCommon.targets(113,5): error MSB3073: :VCEnd» exited with code 1.
========== Build: 0 succeeded, 1 failed, 0 up-to-date, 0 skipped ==========
Источник
Error msb3073 microsoft cppcommon targets
This forum has migrated to Microsoft Q&A. Visit Microsoft Q&A to post new questions.
Asked by:
Question
I have converted a project from VC++ 6.0 to VC++ 2010, and these are the steps I went through when I compiled the project:
- Clean Solution
- Rebuild Solution or
- Build Solution (The 1st time)
Here is the error I get when I follow those steps above:
error MSB3073: The command «regsvr32 /s /c «C:SourceControlMyProject.DebugMyProject.dll»
echo regsvr32 exec. time > «.Debugregsvr32.trg»
echo Execute mtxrereg.exe before using MTS components in MTS
:VCEnd» exited with code 3. C:Program Files (x86)MSBuildMicrosoft.Cppv4.0Microsoft.CppCommon.targets 183 6
However, immediately after getting that error where I do just a “Build Solution” ONLY I get Build succeeded
Under Project > Properties > Configuration Properties > Custom Build Step I have Command Line:
regsvr32 /s /c «$(TargetPath)»
echo regsvr32 exec. time > «$(OutDir)regsvr32.trg»
echo Execute mtxrereg.exe before using MTS components in MTS
Does anyone know why this happens and how I can resolve it?
NOTE: I do have VS 2010 set to “Run As Administrator”
Thanks for your post in the MSDN Forum.
Based my experience and analysis into this issue, I think there some possible reasons for this issue. For example, perhaps the DLL has already been registered successfully, maybe you have not got enough power to register it, and there may be some issues with the codes, etc. At present I am not able to decide which one is the root cause unfortunately.
I suggest you try registering the DLL in command line. Please pay attention that you should run CMD as administrator. If this doesn’t work, please post the error messages here and feel free to let us know. We’ll continue working with you on this issue.
Best regards,
Helen
Helen Zhao [MSFT]
MSDN Community Support | Feedback to us
Thanks for the suggestion. My apologies I should have stated that I have admin rights on my workstation and I have been able to register various DLL’s before. I even took the extra step to pin my CMD to the task bar with “Run As Administrator” set under Shortcut > Advanced. With my Visual Studio 2010 I have done the same thing but I’ve also set “Run this program as an administrator” under the Compatibility tab as well.
Just to recap my steps I did the following:
- Clean Solution
- Build Solution (The 1st time)
I still get error MSB3073, but before I do just a Build ONLY I checked MyProjectDebug folder and it produced the following files:
- MyProject.dll.intermediate.manifest
- MyProject.dll.embed.manifest.res
- MyProject.dll.embed.manifest
- MyProject_manifest.rc
NOTE: Under Project > Properties > Configuration Properties > Linker > General I have “ Output File ” putting MyProject.DLL in a different location (i.e. C:ShareMyProjectBin). So, MyProject.DLL is also created. All 5 files have the same Datetime stamp.
When I do a Build ONLY the second time (NO Clean Solution or Rebuild Solution) it says Build succeeded. So, I do not know what Build does differently the second time that it didn’t do the first time when it fails.
NOTE: Rebuild ONLY produces error MSB3073 every time.
Does having the Output file pointing to a different location make any difference? I assume not since it compiled both times.
Keep in mind that this was upgraded from VC++ 6.0 to 2010 so this was part of the original settings:
regsvr32 /s /c «$(TargetPath)»
echo regsvr32 exec. time > «$(OutDir)regsvr32.trg»
echo Execute mtxrereg.exe before using MTS components in MTS
VC++ 6 have it under Project > Settings… > Custom Build tab, and VC++ 2010 puts it under Project > Properties > Configuration Properties > Custom Build Step
Источник
ошибка MSB3073: как мне это исправить?
Я изучал онлайн, я думаю, что он должен что-то сделать с относительным путём; но я не уверен. Может кто-нибудь помочь объяснить, что не так, и как это исправить?
6 ответов
В моем случае проблема заключалась в том, что VС++ пытался скопировать DLL файл в системную папку. Запуск его как администратора устранил проблему.
Для всех, кто сталкивается с этим вопросом, моя проблема заключалась в том, что целевой каталог содержал пробелы i.e.
C:UsersAdministratorDocumentsVisual Studio 2017projectsblah
Итак, для меня решение заключалось в том, чтобы обернуть $(TargetDir) в двойные кавычки, т.е.
copy..resources* «$ (TargetDir)» /Y
Получите это. Я создал событие post build для автоматического запуска модульных тестов после каждой сборки. Удалите эту настройку, можно решить эту проблему.
У меня была следующая ситуация: Я перезаписывал файлы, которые были защищены от записи с помощью экземпляра события сборки bost-build. Мне нужно некоторое время, чтобы найти это, потому что я скопировал различные файлы, некоторые из них были скопированы с записью, но для всех событий была отображена ошибка. В приведенном ниже примере копируются события 4, 5 и 6, которые указываются перед ошибкой с «Zugriff verweiger» (англ.: access denied): 
Источник
Error msb3073 microsoft cppcommon targets
This forum has migrated to Microsoft Q&A. Visit Microsoft Q&A to post new questions.
Answered by:
Question
I have encountered an error while building RUN_TESTS of qpidbuild (Apache Qpid message broker). The error snapshot is as shown:
1>—— Build started: Project: RUN_TESTS, Configuration: Debug x64 ——
1> Test project D:/qpid_build
1> Start 1: unit_test
1> 1/23 Test #1: unit_test . ***Failed 4.08 sec
1> Start 2: qpid-client-test
1> 2/23 Test #2: qpid-client-test . ***Failed 0.56 sec
1> Start 3: quick_perftest
1> 3/23 Test #3: quick_perftest . ***Failed 0.47 sec
1> Start 4: quick_topictest
1> 4/23 Test #4: quick_topictest . ***Failed 0.55 sec
1> Start 5: quick_txtest
1> 5/23 Test #5: quick_txtest . ***Failed 0.45 sec
1> Start 6: quick_txtest2
1> 6/23 Test #6: quick_txtest2 . ***Failed 0.47 sec
1> Start 7: msg_group_tests
1> 7/23 Test #7: msg_group_tests . ***Failed 0.50 sec
1> Start 8: run_header_test
1> 8/23 Test #8: run_header_test . ***Failed 0.46 sec
1> Start 9: python_tests
1> 9/23 Test #9: python_tests . ***Failed 0.46 sec
1> Start 10: ha_tests
1> 10/23 Test #10: ha_tests . ***Failed 0.46 sec
1> Start 11: qpidd_qmfv2_tests
1> 11/23 Test #11: qpidd_qmfv2_tests . ***Failed 0.46 sec
1> Start 12: swig_python_tests
1> 12/23 Test #12: swig_python_tests . ***Failed 0.46 sec
1> Start 13: ipv6_test
1> 13/23 Test #13: ipv6_test . ***Failed 0.46 sec
1> Start 14: federation_tests
1> 14/23 Test #14: federation_tests . ***Failed 0.53 sec
1> Start 15: federation_sys_tests
1> 15/23 Test #15: federation_sys_tests . ***Failed 0.55 sec
1> Start 16: queue_flow_limit_tests
1> 16/23 Test #16: queue_flow_limit_tests . ***Failed 0.47 sec
1> Start 17: acl_tests
1> 17/23 Test #17: acl_tests . ***Failed 0.55 sec
1> Start 18: cli_tests
1> 18/23 Test #18: cli_tests . ***Failed 0.44 sec
1> Start 19: dynamic_log_level_test
1> 19/23 Test #19: dynamic_log_level_test . ***Failed 0.45 sec
1> Start 20: dynamic_log_hires_timestamp
1> 20/23 Test #20: dynamic_log_hires_timestamp . ***Failed 0.45 sec
1> Start 21: store_tests
1> 21/23 Test #21: store_tests . ***Failed 0.47 sec
1> Start 22: store_tests_clfs
1> 22/23 Test #22: store_tests_clfs . ***Failed 0.46 sec
1> Start 23: queue_redirect
1> 23/23 Test #23: queue_redirect . ***Failed 0.44 sec
1>
1> 0% tests passed, 23 tests failed out of 23
1>
1> Total Test time (real) = 17.80 sec
1>
1> The following tests FAILED:
1> 1 — unit_test (Failed)
1> 2 — qpid-client-test (Failed)
1> 3 — quick_perftest (Failed)
1> 4 — quick_topictest (Failed)
1> 5 — quick_txtest (Failed)
1> 6 — quick_txtest2 (Failed)
1> 7 — msg_group_tests (Failed)
1> 8 — run_header_test (Failed)
1> 9 — python_tests (Failed)
1> 10 — ha_tests (Failed)
1> 11 — qpidd_qmfv2_tests (Failed)
1> 12 — swig_python_tests (Failed)
1> 13 — ipv6_test (Failed)
1> 14 — federation_tests (Failed)
1> 15 — federation_sys_tests (Failed)
1> 16 — queue_flow_limit_tests (Failed)
1> 17 — acl_tests (Failed)
1> 18 — cli_tests (Failed)
1> 19 — dynamic_log_level_test (Failed)
1> 20 — dynamic_log_hires_timestamp (Failed)
1> 21 — store_tests (Failed)
1> 22 — store_tests_clfs (Failed)
1> 23 — queue_redirect (Failed)
1> Errors while running CTest
1>C:Program Files (x86)MSBuildMicrosoft.Cppv4.0V110Microsoft.CppCommon.targets(134,5): error MSB3073: The command «setlocal
1>C:Program Files (x86)MSBuildMicrosoft.Cppv4.0V110Microsoft.CppCommon.targets(134,5): error MSB3073: «C:Program Files (x86)CMake 2.8binctest.exe» —force-new-ctest-process -C Debug
1>C:Program Files (x86)MSBuildMicrosoft.Cppv4.0V110Microsoft.CppCommon.targets(134,5): error MSB3073: if %errorlevel% neq 0 goto :cmEnd
1>C:Program Files (x86)MSBuildMicrosoft.Cppv4.0V110Microsoft.CppCommon.targets(134,5): error MSB3073: :cmEnd
1>C:Program Files (x86)MSBuildMicrosoft.Cppv4.0V110Microsoft.CppCommon.targets(134,5): error MSB3073: endlocal & call :cmErrorLevel %errorlevel% & goto :cmDone
1>C:Program Files (x86)MSBuildMicrosoft.Cppv4.0V110Microsoft.CppCommon.targets(134,5): error MSB3073: :cmErrorLevel
1>C:Program Files (x86)MSBuildMicrosoft.Cppv4.0V110Microsoft.CppCommon.targets(134,5): error MSB3073: exit /b %1
1>C:Program Files (x86)MSBuildMicrosoft.Cppv4.0V110Microsoft.CppCommon.targets(134,5): error MSB3073: :cmDone
1>C:Program Files (x86)MSBuildMicrosoft.Cppv4.0V110Microsoft.CppCommon.targets(134,5): error MSB3073: if %errorlevel% neq 0 goto :VCEnd
1>C:Program Files (x86)MSBuildMicrosoft.Cppv4.0V110Microsoft.CppCommon.targets(134,5): error MSB3073: :VCEnd» exited with code 8.
========== Build: 0 succeeded, 1 failed, 0 up-to-date, 0 skipped ==========
Kindly suggest some solutions.
Answers
Do you mean you have this error when run the RUN_TESTS project directly in Visual Studio? Have you used any msbuild command here?
Based on my experience, your MSB3073 error here means the script(command) is not recognized by MSBuild. I’m not so sure how you what to build your project with MSBuild, but it seems you have to set something here so that Visual Stuido can load your commands and execute the ctest.exe to run test.
Please try open your project file and see the target part in it.
Maybe you need to use something like exec in your solution to execute the command:
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click HERE to participate the survey.
Источник
Я пытаюсь построить проект с открытым исходным кодом на моем компьютере с использованием Visual Studio 2015 и CMake. Я выполнил все шаги, и проверки перед сборкой работали правильно. Но когда я собираю INSTALL для установки программного обеспечения в папку, указанную в графическом интерфейсе CMAKE, я получаю ошибку MSB3073. Полное описание ошибки приведено ниже.
Severity Code Description Project File Line Suppression State Error
MSB3073 The command "setlocal
"C:Program Files (x86)CMakebincmake.exe" -DBUILD_TYPE=RelWithDebInfo -P cmake_install.cmake
if %errorlevel% neq 0 goto :cmEnd
:cmEnd
endlocal & call :cmErrorLevel %errorlevel% & goto :cmDone
:cmErrorLevel
exit /b %1
:cmDone
if %errorlevel% neq 0 goto :VCEnd
:VCEnd" exited with code 1.
INSTALL C:Program Files (x86)MSBuildMicrosoft.Cppv4.0V140Microsoft.CppCommon.targets 133
Я искал ту же ошибку и обнаружил, что некоторые люди, которые пытались установить сборку в каталог без прав записи, сталкивались с этим, но я удостоверился, что у меня есть доступ для записи. Я даже пытался сделать это с правами администратора и до сих пор не смог решить эту проблему.
Любая помощь в этом будет принята с благодарностью.
1
Решение
Произошла ошибка в одном из файлов cmake_install.cmake, и это вызывало проблему. Как только я исправил проблему, все заработало.
-1
Другие решения
Других решений пока нет …
When running this command in the pre-link step (from inside MSVC, when building a project), cmake is crashing, and it gives an error like this:
5>C:Program Files (x86)MSBuildMicrosoft.Cppv4.0V140Microsoft.CppCommon.targets(128,5): error MSB3073: The command "setlocal
5>C:Program Files (x86)MSBuildMicrosoft.Cppv4.0V140Microsoft.CppCommon.targets(128,5): error MSB3073: cd D:build14
5>C:Program Files (x86)MSBuildMicrosoft.Cppv4.0V140Microsoft.CppCommon.targets(128,5): error MSB3073: if %errorlevel% neq 0 goto :cmEnd
5>C:Program Files (x86)MSBuildMicrosoft.Cppv4.0V140Microsoft.CppCommon.targets(128,5): error MSB3073: D:bincmake.exe -E __create_def D:/build14/source/.../RelWithDebInfo//exportall.def D:/build14/source/.../RelWithDebInfo//objects.txt
5>C:Program Files (x86)MSBuildMicrosoft.Cppv4.0V140Microsoft.CppCommon.targets(128,5): error MSB3073: if %errorlevel% neq 0 goto :cmEnd
5>C:Program Files (x86)MSBuildMicrosoft.Cppv4.0V140Microsoft.CppCommon.targets(128,5): error MSB3073: :cmEnd
5>C:Program Files (x86)MSBuildMicrosoft.Cppv4.0V140Microsoft.CppCommon.targets(128,5): error MSB3073: endlocal & call :cmErrorLevel %errorlevel% & goto :cmDone
5>C:Program Files (x86)MSBuildMicrosoft.Cppv4.0V140Microsoft.CppCommon.targets(128,5): error MSB3073: :cmErrorLevel
5>C:Program Files (x86)MSBuildMicrosoft.Cppv4.0V140Microsoft.CppCommon.targets(128,5): error MSB3073: exit /b %1
5>C:Program Files (x86)MSBuildMicrosoft.Cppv4.0V140Microsoft.CppCommon.targets(128,5): error MSB3073: :cmDone
5>C:Program Files (x86)MSBuildMicrosoft.Cppv4.0V140Microsoft.CppCommon.targets(128,5): error MSB3073: if %errorlevel% neq 0 goto :VCEnd
5>C:Program Files (x86)MSBuildMicrosoft.Cppv4.0V140Microsoft.CppCommon.targets(128,5): error MSB3073: :VCEnd" exited with code -1073741819.