Error msg unable to process command password is set but no password file is provided

Original Bios v1.05
Upgrade Bios v1.08
Bios Configurator v.4.0.15.1
Windows 10 v1607
Laptop: EliteBook 1040 G3

I’m trying to setup SCCM to automate configuring a BIOS password, enabling the TPM and storing the details in AD. I’m worndering if anyone has this setup as I’m running in some issues.

Setup.
1. Created a BiosPassword.bin file from the password configurator — works
2. Created a package in SCCM with the required files
3. Created TS step to set password — BIOSConfigUtility64.exe /npwdfile:BiosPassword.bin — works
4. Created step to Enable TPM — BiosConfigUtility64.exe /SetConfig:EnTPM1040G3.REPSET /cpwdfile:BiosPassword.bin — fails

Failure message:
<ERROR msg=»Unable to process command. Password is set, but no password file is provided» />
<ERROR msg=»BCU return value» real=»10″ translated=»10″ />
Failed to run the action: Enable TPM for HP EliteBook 1040 G3. The environment is incorrect. (Error: 0000000A; Source: Windows)

Testing: The TS complains about the password file yet it’s the same bin file used to set the password.
1. Created a joint step to set password and enable TPM but fails with the same error
— BiosConfigUtility64.exe /SetConfig:EnableTPM1040G3.REPSET /nspwdfile:BiosPassword.bin

2. Ran the file directly from a PC — file runs and the password is accepted but cannot change TPM activation policy so prompted for F1 on a manual reboot
TPM Activation Policy, 
    F1 to Boot
    Allow user to reject
    *No prompts

3. Upgraded the Bios but I get the same two failures.

4. Placed a restart computer step into the TS after the Enable of TPM but makes no difference as initial file fails to run.

Any thoughts would be appreciated. Don’t know why I getting failed password response since the same bin file is being used. Also don’t want users to be prompted to enable TPM as this removes the zero touch deployment.

SCCM,enable TPM w/HP Bios Configurator:Password is set,no password file provided

Original Bios v1.05
Upgrade Bios v1.08
Bios Configurator v.4.0.15.1
Windows 10 v1607
Laptop: EliteBook 1040 G3

I’m trying to setup SCCM to automate configuring a BIOS password, enabling the TPM and storing the details in AD. I’m worndering if anyone has this setup as I’m running in some issues.

Setup.
1. Created a BiosPassword.bin file from the password configurator — works
2. Created a package in SCCM with the required files
3. Created TS step to set password — BIOSConfigUtility64.exe /npwdfile:BiosPassword.bin — works
4. Created step to Enable TPM — BiosConfigUtility64.exe /SetConfig:EnTPM1040G3.REPSET /cpwdfile:BiosPassword.bin — fails

Failure message:

Failed to run the action: Enable TPM for HP EliteBook 1040 G3. The environment is incorrect. (Error: 0000000A; Source: Windows)

Testing: The TS complains about the password file yet it’s the same bin file used to set the password.
1. Created a joint step to set password and enable TPM but fails with the same error
— BiosConfigUtility64.exe /SetConfig:EnableTPM1040G3.REPSET /nspwdfile:BiosPassword.bin

2. Ran the file directly from a PC — file runs and the password is accepted but cannot change TPM activation policy so prompted for F1 on a manual reboot
TPM Activation Policy,
F1 to Boot
Allow user to reject
*No prompts

3. Upgraded the Bios but I get the same two failures.

4. Placed a restart computer step into the TS after the Enable of TPM but makes no difference as initial file fails to run.

Any thoughts would be appreciated. Don’t know why I getting failed password response since the same bin file is being used. Also don’t want users to be prompted to enable TPM as this removes the zero touch deployment.

Источник

Error msg bcu return value real 10 translated 10

‎09-15-2015 03:02 AM

• Mark as New
• Bookmark
• Subscribe
• Permalink
• Print
• Flag Post

I’m using the HP BIOS Configuration Utility (BCU v. 4.0.13.1) to change BIOS configuration.

So I set up a new BIOS password with the HPQPswd tool.

Everything worked fine. Password is activated.

After that I tried to do some changes relating to the boot order.

But everytime, wether with a config file nor with the command «/setvalue:»», the following error message appears:

So I have to provide the password file, but how? Or is there any other mistake?

Thanks for your response!

‎09-15-2015 05:50 AM

• Mark as New
• Bookmark
• Subscribe
• Permalink
• Print
• Flag Post

Well, I think I found the problem:

BiosConfigUtility64.exe /set:»Filename.txt» /cspwdfile:»Filename.bin»

But now i receive a new error message:

So I hope somebody can explain me this message or help me with that.

BCU version is v. 4.0.13.1

Thanks for your response!

‎12-07-2015 08:54 AM

• Mark as New
• Bookmark
• Subscribe
• Permalink
• Print
• Flag Post

Error Code 10:
Valid password not provided. BCU was unable to find a valid password on the command line in the following cases:

• When attempting to change the password, the correct password was not provided.
• When attempting to change the password, the new password did not satisfy password requirements for the platform.
• When attempting to change setting values, the correct password was not provided.

You are probably using the wrong password-file. Its probably not the file originally created to set the password.

Find the original file or log into the bios and set the password to blank.

Then use the new password file to set the password. (And dont lose it this time and make sure its backed up)

Now run the command again. At least you can verify you are using the wrong file this way. And if you are, i hope you dont have thousands of computers you need to do this on.

Also if the passwords were originally set with the old tools that used clear text passwords, you might be able to use the old versions of BCU to unlock the BIOS.

Источник

Error msg bcu return value real 10 translated 10

‎08-16-2016 11:13 AM

• Mark as New
• Bookmark
• Subscribe
• Permalink
• Print
• Flag Post

trying to change BIOS language using HP Bios Configuration Utility but get Error code 6 — Access Denied (failed due to BIOS permissions).

BIOS version is THI vA0.08.

I can read (get) successfully but cannot change any setting. tried to change other settings unsuccessfully.

What am I missing? Do I need to set a password first?

‎08-19-2016 08:38 AM

• Mark as New
• Bookmark
• Subscribe
• Permalink
• Print
• Flag Post

Welcome to the HP Support Forums! I understand that you wish to change the BIOS language on your system to English from the current Dutch. I am happy to assist you with this.

Was Dutch the language that the BIOS was set to out of the box or was it later changed to Dutch?

If the systems’ original default was English, you could try looking at the motherboard guide for your system. HP and Compaq Desktop PCs — motherboard specifications, Thimphu. At the bottom of the page is an indicator for the Jumpers for the CMOS and BIOS password. If your default language was English you could use the jumper to clear the current CMOS settings, including the language.

Please let me know whether that works for you, and if it does resolve your issue, please mark this post as a solution. Kudos would also be appreciated.

‎08-16-2016 11:20 AM

• Mark as New
• Bookmark
• Subscribe
• Permalink
• Print
• Flag Post

I should have mentioned.

language is currently Dutch and I would like to set it to English. I removed the * and placed in front of English. essentially following instructions in the manual so that is not the issue.

thanks in advance for your help

‎08-19-2016 08:38 AM

• Mark as New
• Bookmark
• Subscribe
• Permalink
• Print
• Flag Post

Welcome to the HP Support Forums! I understand that you wish to change the BIOS language on your system to English from the current Dutch. I am happy to assist you with this.

Was Dutch the language that the BIOS was set to out of the box or was it later changed to Dutch?

If the systems’ original default was English, you could try looking at the motherboard guide for your system. HP and Compaq Desktop PCs — motherboard specifications, Thimphu. At the bottom of the page is an indicator for the Jumpers for the CMOS and BIOS password. If your default language was English you could use the jumper to clear the current CMOS settings, including the language.

Please let me know whether that works for you, and if it does resolve your issue, please mark this post as a solution. Kudos would also be appreciated.

‎08-22-2016 09:37 PM — edited ‎08-25-2016 07:22 AM

• Mark as New
• Bookmark
• Subscribe
• Permalink
• Print
• Flag Post

Firstly, thank you very much for your support.

The language was Dutch out of the box. I think the problem is that I can’t set the password.

I’ve tried the following:

I set the password in the BIOS to «dd».

HPQPswd64.exe /s /p»dd» /f»dd.bin»

. but that didn’t work.

‎08-23-2016 07:17 AM — edited ‎08-25-2016 07:25 AM

• Mark as New
• Bookmark
• Subscribe
• Permalink
• Print
• Flag Post

Sorry . I should provided the error I get .

I’ve tried an easy password like «dd». I’ve also tried «abcd1234» as password but with same results.

I also cleared CMOS and password using jumpers on motherboard and tried all the above again.

I can access the BIOS at bootup with ESC without using a password.

‎08-26-2016 08:10 AM

• Mark as New
• Bookmark
• Subscribe
• Permalink
• Print
• Flag Post

Flashing BIOS may reset the language to English, The link below will explain how to Update/Flash BIOS:

You can download the latest BIOS update for your desktop PC from the link below:

Let me know how it goes

I am an HP Employee

‎08-28-2016 09:27 PM — edited ‎08-28-2016 09:31 PM

• Mark as New
• Bookmark
• Subscribe
• Permalink
• Print
• Flag Post

Thank you for response.

I already did that but the language remained Dutch. BIOS version is latest A0.14 Rev.A.

I think the problem is that I can’t set the password. I am hoping that once I can set the password using BCU I will be able to use BCU to change the language.

I’ve tried the following:

I set the password in the BIOS to «dd».

HPQPswd64.exe /s /p»dd» /f»pwd.bin»

I got the following error:

Besides the easy password «dd» I also tried «abcd1234» as password but with same results.

I also cleared CMOS and password using jumpers on motherboard and tried all the above again.

I can access the BIOS at bootup — it currrently doesn’t have a password.

Is it possible that I am not using a valid passowrd format i.e. must have uppercase and lower case characters as well as numbers etc?

Could it be TPM 2.0 . not sure what this security device is but could that be blocking me from setting a password?

‎08-29-2016 09:59 AM

• Mark as New
• Bookmark
• Subscribe
• Permalink
• Print
• Flag Post

Found another way to change the BIOS language. Let’s try that.

1. Open the installation directory of “BIOS configuration utility”. Path: C:Program Files (x86)Hewlett-PackardSSM
2. Press Shift key+right mouse button and select “Open command window here”
3. Type “BIOSConfigutility.exe/getconfig:config.txt” and hit “Enter”, this will create a dump file in the same directory.
4. Open “config.txt”, scroll down till you find the Language option.
5. The language with the “*” in front of it is the one that is enabled. In your case, remove the * from before Deutsch and add the * before English and save the file.
6. Again Press Shift key+right mouse button and select “Open command window here”
7. Type “BIOSConfigutility.exe/setconfig:config.txt” and hit “Enter”.

Restart the computer, access BIOS and see if the language has been changed.

Let me know how it goes

Senan6806 — HP Support Agent

**Click on the KUDOS Star on the left to say «thanks» for helping!**

**Please Mark a Reply «Accept As Solution» if this has resolved your issue.**

Источник

MDT Bios update with password

I’m trying to make a sequence to update the bios for our HP laptops. I have the needed bios update files etc, but the bios is protected with a password.
Is there a way to use the password in de sequence? Can I add it in a command line or script?
In this topic the anwser is to use command line and HP procedures, but I can’t find those.

Anyone who has experience with this?

3 answers

In your sequence, can you run the hp software that update with a command line ? It would be the way to do it.

See there for a command line; HP BIOS Configuration Utility (BCU); https://ftp.ext.hp.com/pub/caps-softpaq/cmit/HP_BCU.html

HPBiosUpdRec [-s] [-pPasswordFile] [-fROMBINFile] [-a] [-h] [-?]

-s: Silent mode.
-p: Specify encrypted password file created with the HpqPswd utility.
-f: Specify ROM BIN file. Default is BIN file in same folder as exe.
-a: (Silent mode only) Always flash, ignore version comparison.
-h: Create HP_TOOLS partition if not present.
-?: Display usage.
-b: Suspend BitLocker if needed.
-r: Prevent autoreboot after the BIOS update.

And you need to run HPQPswd.exe to create the password file.

HpqPswd.exe /s /p»password123″ /f»password.bin»

I used the software to create a password file but the .bin file is not being used. Can I provide a log file for you?

Источник

Error msg bcu return value real 10 translated 10

‎12-08-2020 02:35 AM

• Mark as New
• Bookmark
• Subscribe
• Permalink
• Print
• Flag Post

I fight wth the following problem.

I bought a used Probook 650G1. When I tried to reinstall Windows, it can not boot from USB. I think it was disabled, but I can not check, because BIOS request PW to enter but I can’t get it from the seller. What I tried before:

1) Disconnect BIOS battery (mian battery and power cord also disconnected)

2) Running HP BCU biosconfigutility.exe /newsetuppassword:»12345″

I got error message:

3)Use HP Bios Reset Utlty. USB drive created, but still not boot from it.

T hanks for your help.

‎12-08-2020 08:04 AM

• Mark as New
• Bookmark
• Subscribe
• Permalink
• Print
• Flag Post

Hi there! Thank you for visiting the HP Support Community!

According to the Community’s Rules of Participation:

4d. No posts shall include instructions or directions intended to bypass or subvert security measures, including passwords, locking mechanisms, fingerprint scans, etc., or to bypass any safety measures.

Therefore, this topic is being locked. If you would like help resetting the password on your product, please Contact HP support in your region.

Источник

Here is the scenario:


An employee was fired from the company some time ago and his old laptop has a BIOS password set by HP ProtectTools. Here is the procedure to remove the password and completely remove BIOS security. It assumes you can still login to Windows on the computer with a user with admin rights.

1. Download the current version of HP System Software Manager (SSM). As of October 2014 it is version 3.1.10.1 in SoftPaq 66796 and can be found here.
2. Run the sp66796.exe file and accept all defaults.
3. Go to the C:Program Files (x86)Hewlett-PackardSystemSoftwareManager folder and extract there the SSM.cab file with 7-Zip or another compressed file manager.
4. Double-click the HpqPswd.exe file
5. Choose a new BIOS Administrator password (minimum 8 characters), type it in the 2 Password fields and type the name of the password file (I use pass.bin) and click OK.
6. Download the current HP BIOS Configuration Utility (BCU). As of October 2014 it is version 3.0.13.1 in SoftPaq 65619 and can be found here.
7. Run the sp65619.exe file and accept all defaults.
8. Copy the pass.bin file created in step 5 to the C:Program Files (x86)Hewlett-PackardBIOS Configuration Utility folder
9. Open a Command Prompt and go to the C:Program Files (x86)Hewlett-PackardBIOS Configuration Utility folder.
10. Type this command: BIOSConfigUtility64.exe /nspwdfile:pass.bin .This will set a new BIOS Administrator password.
11. Restart the computer and enter BIOS setup (F10 on most models).
12. Select user BIOS Administrator and type the password you chose in step 5.
13. In the Security Tab click the User Management option.
14. In the HP PROTECTTOOLS USERS section select all the users one by one and and click Delete Account.
15. Go back to the Security Tab and click Change Password
16. Type the password you chose in step 5 and press Enter 3 times to select a blank password.
17. Exit the BIOS setup and save the changes.
18. To make sure that it worked enter the BIOS setup and you should not be asked any password.

Credits: the above procedure is an adaptation from this post to use the available versions of HP SSM and BCU.

инструкции

To Fix (Enabling TPM with sccm deployment fails — Password is set, b…) error you need to follow the steps below:
Шаг 1:
Download (Enabling TPM with sccm deployment fails — Password is set, b…) Repair Tool
Шаг 2:
Нажмите «Scan» кнопка
Шаг 3:
Нажмите ‘Исправь все‘ и вы сделали!
Совместимость: Windows 10, 8.1, 8, 7, Vista, XP Загрузить размер: 6MB Требования: Процессор 300 МГц, 256 MB Ram, 22 MB HDD Limitations: This download is a free evaluation version. Full repairs starting at $19.95.

Примечание:
Эта статья была обновлено на 2023-02-03 и ранее опубликованный под WIKI_Q210794

Meaning of Enabling TPM with sccm deployment fails — Password is set, b…?

Enabling TPM with sccm deployment fails — Password is set, b… is the error name that contains the details of the error, including why it occurred, which system component or application malfunctioned to cause this error along with some other information. The numerical code in the error name contains data that can be deciphered by the manufacturer of the component or application that malfunctioned. The error using this code may occur in many different locations within the system, so even though it carries some details in its name, it is still difficult for a user to pinpoint and fix the error cause without specific technical knowledge or appropriate software.

Causes of Enabling TPM with sccm deployment fails — Password is set, b…?

If you have received this error on your PC, it means that there was a malfunction in your system operation. Common reasons include incorrect or failed installation or uninstallation of software that may have left invalid entries in your Windows registry, consequences of a virus or malware attack, improper system shutdown due to a power failure or another factor, someone with little technical knowledge accidentally deleting a necessary system file or registry entry, as well as a number of other causes. The immediate cause of the «Enabling TPM with sccm deployment fails — Password is set, b…» error is a failure to correctly run one of its normal operations by a system or application component.

More info on
Enabling TPM with sccm deployment fails — Password is set, b…

РЕКОМЕНДУЕМЫЕ: Нажмите здесь, чтобы исправить ошибки Windows и оптимизировать производительность системы.

I’m worndering if anyone has this TPM but fails with the same error- BiosConfigUtility64.exe /SetConfig:EnableTPM1040G3.REPSET /nspwdfile:BiosPassword.bin 2. Created a BiosPassword.bin file from password — BIOSConfigUtility64.exe /npwdfile:BiosPassword.bin — works4. Created a joint step to set password and enable setup as I’m running in some issues. Setup.1. Created TS step to set automate configuring a BIOS password, enabling the TPM and storing the details in AD.

Don’t know why I getting failed password response SCCM with the required files3. The environment is incorrect. (Error: 0000000A; Source: Windows) Testing: The TS complains about TPM as this removes the zero touch deployment. 

Placed a restart computer step into the TS after the Enable of TPM the password configurator — works2. Upgraded the Bios but I the password file yet it’s the same file used to set the password.1.

Created step to En TPM — BiosConfigUtility64.exe /SetConfig:EnTPM1040G3.REPSET get the same two failures. 4. Password is set, but no password file is provided» /><ERROR msg=»BCU return value» since the same bin file is being used.

Original Bios v1.05Upgrade Bios v1.08Bios Configurator v.4.0.15.1Windows 10 v1607 I’m trying to setup SCCM to real=»10″ translated=»10″ />Failed to run the action: Enable TPM for HP EliteBook 1040 G3. Also don’t want users to be prompted to enable /cpwdfile:BiosPassword.bin — fails Failure message:<ERROR msg=»Unable to process command.

Created a package in but makes no difference as initial file fails to run. Any thoughts would be apprecaited.
Развертывание операционной системы SCCM не выполняется, когда BIOS установлен на …

---

BSOD after first reboot using SCCM deployment

I am using SCCM to deploy a Win7 x64 image
and for some safemode With network and normal Windows start and all that. And the screen shows after that the normal choices between
safemode, files to analyze it could be anything.

---

E7470 SCCM 2012 TS deployment issues

---

X1 Carbon — проблема развертывания изображения SCCM

Пожалуйста, опубликуйте. Проблема в том, что она, похоже, не в состоянии, и у меня нет этой проблемы на этих моделях. Когда я выбираю локальный жесткий диск, он возвращается обратно к тому же экрану.

---

Windows 7 SCCM Развертывание вопросов VPN / компьютера

---

Проблема UEFI предотвращает развертывание SOE SCCM OSD

ПК и застревание в петле. Изображение на нескольких других машинах, но проблема с EliteDesk 800. Последовательность задач перезапускает

---

SCCM deployment of Microsoft Certificate Update

What version of the certificate updates should I deploy for Windows 7 using SCCM 2012R2, is there any documentation for the process?

---

SCCM 2012 — развертывание драйвера Optiplex 7040

Любой, кого я уже видел, и это загрузочное изображение отлично работает на всех других аппаратных моделях.

---

m710q: SCCM 1702 Deployment issues with Windows 7

---

Latitude E5270 — SCCM 2012 R2 deployment — BSOD 7B

booting Windows 7 x64 for the first time. Hi,
I have spent days of troubleshooting this deployment . It is still crashing with BSOD 7b when Help is greatly appreciated.

---

Проблема развертывания с широтой E7470 из SCCM 2012 OSD

now it shows a valid IP. Update:
I used a driver grabber software (ConfigMgrDriverGrabber) to drivers for the system has been applied. I tried to add this to the TS and now it «ipconfig /renew» it updates to a valid IP. We downloaded the CAB from Dell (en.community.dell.com/…/11830.latitude-e7470-windows-7-driver-pack) and created

We have no issues with all a driver package from this like we always do. other Dell models we are installing. The TS fails right after the grab the drivers from one of the preinstalled E7470’s. I have tried with two different E7470’s to check if it was faulty hardware but it is the same on both machines.

Anyone else having new driver package and it works now. If I check the IP see that it is getting a 169.x.x.x IP address. Then I imported those to a trouble with this model? When I press F8 and type IP config I fails when the applications are about to be installed (error 0x80004005/unknown error).

If I try to renew the address with

---

Проблемы с блокировкой бит с компьютерами ThinkCentre с развертыванием SCCM

All We are having problems with deploying 8.1 and enabling bitlocker on ThinkCentre machines m93p p300 and p500.

---

Need Help Setting up SCCM 2016 (1606) for PXE Boot and OS Deployment

FWIW:  https://social.technet.microsoft.com/wiki/contents/articles/36614.sccm-1606-step-by-step-walk-through-setup.aspx or after I install SCCM? If so, how am I supposed HELP!!!
I’ve been trying to set SCCM 2016 up so step-by-step guide on how to properly set all this up.

I just can’t seem to find a nice, clear, easy-to-follow, to configure it for SCCM PXE boot? But I just CANNOT get need WDS installed? Do I configure it before I can use it to deploy OSs via PXE boot.

---

Проблема развертывания с широтой E7270 из SCCM 2012 OSD

Загрузка с этого изображения также привела к тому, что сетевой адаптер не был обнаружен, я загрузил последний пакет драйверов WinPE от Dell, который был введен. Он должен находиться здесь после того, как вы извлекли исполняемый файл: C: yada … PRO1000 Winx64 .

My company currently runs SCCM 2012 SP1 (not R2/no CU’s) with the ADK for Windows 8.0 and we deploy to a variety of Dell laptops including the 7240 and 7250. Just import them, and existing boot media it did not detect the network adapter. I was working on E7470 the other day and the I219-LM drivers but when I injected the Dell WinPE drivers manually it finally showed network connectivity. I then created a WinPE the drivers into our boot image, and still no luck.

Кто-нибудь еще испытывает добавление к вашему загрузочному изображению.

---

SCCM PXE развертывание Windows 7 64bit на ноутбуке V110 — нет драйвера Lan

Любая помощь все еще нужна — просто нужно исправить это, все остальное работает нормально. В обычном месте нет журналов! Невозможно перейти в Windows 10.

---

SCCM PXE развертывание Windows 7 64bit на ноутбуке V110 — нет драйвера Lan

---

Enabling the TPM via SCCM 2012 R2 on T440p

What is the current Solved! state of the TPM?

---

Optiplex 5040 PXE Deployment Issue | WINPE5.0 Boot Image SCCM 2012

Not able to get the PXE working on 5040 . boot image from SCCM DP. It will download the

---

Пользовательское развертывание изображений Windows 7 через SCCM 2007 на Dell 5570 (BSOD, 0x0000007B)

Через SCCM.I попробовали поддержку Dell и SSD, чтобы распознать и запустить последовательность задач запуска. Благодаря,

Мадхусудан

ниже с небольшим успехом. Я уже пробовал. Любая помощь здесь очень ценится, так как у меня есть 20 новый ноутбук Dell 5570 с пользовательским Windows 7 SP1 Ent.

Мне пришлось импортировать драйверы Samsung NVMe в загрузочный образ для Now: задача с моим загрузочным изображением SSD не была распознана. Во-первых: у меня возникли проблемы с загрузкой ноутбуков для ноутбуков, уже приобретенных у Dell, и ожидающих их отображения перед развертыванием. Сразу же после «Настройка Windows и ConfigMgr» их помощь пока не удовлетворительна, к сожалению.

Здравствуйте,

У меня возникают проблемы со съемкой ноутбука и сбои с ошибкой «0x0000007B». последовательность не проходит.

---

Развертывание Windows 8.1 для SCCM Windows — Sysprep не смог разобрать или обработать файл ответов автоматической установки для специализации pass

Я видел много других сообщений об этой ошибке, но я отвечаю за файл ответов на передачу [specialize]. В CBS мы проследили процесс установки, где драйверы были проблемой драйверов для нас, как и предполагалось. После этого мы применили KB 2837108 и KB 2921916. Ошибка:

Sysprep не смог разобрать или обработать параметры обработки для компонента [Microsoft-Windows-Shell-Setup].

В SCCM мы игнорировали ошибки импорта драйверов при использовании утилиты Dell Command Deploy для CAB. Я думаю, что мы

сузили это к некоторым машинам, но не к другим? Говоря с поддержкой Premier, мы выкапывали драйверы в SCCM, но они не были. Ошибка установки немедленно отправлена ​​отдельно.

Ошибка sysprep привела к неспособности сервера

для распознавания новых драйверов Windows 8.1. Кто-нибудь испытал CBS.log на неудавшейся машине и подтвердил это. У нас сложилось впечатление, что наши драйверы устройств, но, похоже, не могут понять это. Заранее спасибо!!

---