OrCAD Tip) ERROR(ORCAP-1032), ERROR(ORCAP-1172)
OrCAD Capture
2018. 4. 19. 16:31
https://blog.naver.com/kingreddrake/221256735658
Lite 버전에서는 사용할 수 있는 Part 와 Wire의 수가 제한이 있습니다.
아래의 제한을 넘을 경우 저장 및 시뮬레이션이 불가능합니다.
OrCAD Capture CIS Lite |
■ 회로도 설계 시 평면 도면, 계층 도면를 포함하여 75 Net 이하로 설계 가능. |
PSpice Lite |
■ 75개 node, 20개 transistor, 65개 디지털 요소, 10개 transmission line (커플링는 4개) 이하로 설계 가능 ■ 디지털회로에서 최대 250 이하 노드 설계 가능. evalp.lib (파라미터 속성 라이브러리) 제공 (참고 : http://blog.naver.com/kingreddrake/220669096982 ) ■ Level 3 코어모델 (Tabrizi), MOSFET BSIM 3.2 모델, MOSFET BSIM 4 모델을 시뮬레이션 불가. ■ DMI 모델, IBIS 모델 지원하지 않음 |
OrCAD PCB Editor Lite |
■ 50 component 이상일 시 저장이 되지 않음 ■ 100 net 이상일 시 저장되지 않음 |
만약 회로도 설계 시 75 Net 또는 60 Part 이상이 회로도에 설계 되었을 경우 아래와 같이 출력되며, 저장되지 않습니다.
Warning: Lite Edition can only save a schematic with 60 or less components and 75 or less nets. This design exceeds that limit and future changes can not be saved.
ERROR(ORCAP-1032): Lite Editon is limited to 60 or less components and 75 or less nets. Can not complete Save.
위 조건을 넘어서 설계하고 PSpice 시뮬레이션 시 에는 아래와 같이 에러 메세지가 출력됩니다.
ERROR(ORCAP-15052): Simulation aborted because there are errors during netlisting. Please refer to the session log.
그리고 세션 로그를 확인하면 아래와 같이 출력되며,
ERROR(ORCAP-1172): Lite Editon is limited to 60 or less components and 75 or less nets. Can not netlist.
시뮬레이션 결과창에는 다음과 같이 출력됩니다.
ERROR — EVALUATION VERSION analog Node Limit (75 Nodes) Exceeded !
위 와 같이 경고창이 나타나면….
Lite 버전으로는 회로 작성 및 시뮬레이션이 불가능 하며, 정품이나 Trial 버전으로 설계해야 됩니다.
정품일 경우에는 라이선스 동작 여부를 확인하여야 합니다.
Skip to main content
Welcome to EDAboard.com
Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals… and a whole lot more! To participate you need to register. Registration is free. Click here to register now.
-
Hardware and PCB Design
-
PCB Routing Schematic Layout software and Simulation programs
You should upgrade or use an alternative browser.
OrCAD unable to find netlist file.
-
Thread starterYilin Yamamoto
-
Start dateJun 30, 2013
- Status
- Not open for further replies.
-
#1
- Joined
- Jun 30, 2013
- Messages
- 1
- Helped
- 0
- Reputation
-
0
- Reaction score
- 0
- Trophy points
- 1
- Activity points
-
23
I’m quite new to this OrCAD Capture software, using a 9.1 edition.
I’m actually patching up a circuit for a charge controller according to this link: https://www.mdpub.com/555Controller/images/555ChargeController.jpg
This is my schematic diagram.
https://obrazki.elektroda.pl/6855597400_1372616126.png
But when I click on Run simulation, it shows the message in the output file «unable to find netlist file….simulation aborted»
I did some searching for any similar problem and below are the possible solutions:
1) Generating a layout netlist
— Bring up the project window.
— Select the schematic that is being worked with.
— Under «Tools» menu, select «Create Netlist» (for mine, I need to go under «PSpice» menu)
— Select «layout» on the top tabs
— The defaults should be correct for the file name to create the file dimensions. Press ok to create the netlist.
[While doing this above steps, a window pop out instead after step 3, displaying the message «Simulation aborted because there are errors during netlisting. Please refer to session log».
The session log displayed «Creating PSpice Netlist Writing PSpice Flat Netlist G:MPSIPPSPICEORCAD_DEMOCAPTURE1CHARGE CONTROLLER-SCHEMATIC1.net
ERROR [NET0075] Unconnected pin, no FLOAT property or FLOAT = e U7 pin ‘NO’
So I went to try how to correct the error with the below solution I found in the net]
2) SOLUTION from www.orcad.com
— In Capture, select the part.
— From the Edit menu, choose Part.
— Double-click the pin. The Pin Properties dialog blox appears.
— Click the user Properties button and make sure that there is a FLOAT property with the value UniqueNet listed. Add this property and value if it is missing. Click OK.
— From the File menu, choose close to save the instance. Click the update ALL button.
[After this, I went to run the simulation, but still theres is still the message «unable to find netlist file….simulation aborted.»
But when I went to create and view the netlist, the session log displayed
«Creating PSpice Netlist
Writing PSpice Flat Netlist G:MPSIPPSPICEORCAD_DEMOCAPTURE1CHARGE CONTROLLER-SCHEMATIC1.net
PSpice netlist generation complete» ]
Anyone can help me with this? I really have no idea why it does not run the simulation after all I had done. Thanks.
-
#2
Ow@i$
Advanced Member level 1
- Joined
- Sep 18, 2012
- Messages
- 413
- Helped
- 78
- Reputation
-
156
- Reaction score
- 75
- Trophy points
- 1,308
- Location
-
Pakistan
- Activity points
-
3,430
- Status
- Not open for further replies.
Similar threads
-
Hardware and PCB Design
-
PCB Routing Schematic Layout software and Simulation programs
-
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
Click here follow the steps to fix Orcad Error Orcap-1558 and related errors.
|
|
To Fix (Orcad Error Orcap-1558) error you need to |
|
Step 1: |
|
---|---|
Download (Orcad Error Orcap-1558) Repair Tool |
|
Step 2: |
|
Click the «Scan» button | |
Step 3: |
|
Click ‘Fix All‘ and you’re done! | |
Compatibility:
Limitations: |
Orcad Error Orcap-1558 Error Codes are caused in one way or another by misconfigured system files
in your windows operating system.
If you have Orcad Error Orcap-1558 errors then we strongly recommend that you
Download (Orcad Error Orcap-1558) Repair Tool.
This article contains information that shows you how to fix
Orcad Error Orcap-1558
both
(manually) and (automatically) , In addition, this article will help you troubleshoot some common error messages related to Orcad Error Orcap-1558 error code that you may receive.
Note:
This article was updated on 2023-02-03 and previously published under WIKI_Q210794
Contents
- 1. What is Orcad Error Orcap-1558 error?
- 2. What causes Orcad Error Orcap-1558 error?
- 3. How to easily fix Orcad Error Orcap-1558 errors
What is Orcad Error Orcap-1558 error?
The Orcad Error Orcap-1558 error is the Hexadecimal format of the error caused. This is common error code format used by windows and other windows compatible software and driver vendors.
This code is used by the vendor to identify the error caused. This Orcad Error Orcap-1558 error code has a numeric error number and a technical description. In some cases the error may have more parameters in Orcad Error Orcap-1558 format .This additional hexadecimal code are the address of the memory locations where the instruction(s) was loaded at the time of the error.
What causes Orcad Error Orcap-1558 error?
The Orcad Error Orcap-1558 error may be caused by windows system files damage. The corrupted system files entries can be a real threat to the well being of your computer.
There can be many events which may have resulted in the system files errors. An incomplete installation, an incomplete uninstall, improper deletion of applications or hardware. It can also be caused if your computer is recovered from a virus or adware/spyware
attack or by an improper shutdown of the computer. All the above actives
may result in the deletion or corruption of the entries in the windows
system files. This corrupted system file will lead to the missing and wrongly
linked information and files needed for the proper working of the
application.
How to easily fix Orcad Error Orcap-1558 error?
There are two (2) ways to fix Orcad Error Orcap-1558 Error:
Advanced Computer User Solution (manual update):
1) Start your computer and log on as an administrator.
2) Click the Start button then select All Programs, Accessories, System Tools, and then click System Restore.
3) In the new window, select «Restore my computer to an earlier time» option and then click Next.
4) Select the most recent system restore point from the «On this list, click a restore point» list, and then click Next.
5) Click Next on the confirmation window.
6) Restarts the computer when the restoration is finished.
Novice Computer User Solution (completely automated):
1) Download (Orcad Error Orcap-1558) repair utility.
2) Install program and click Scan button.
3) Click the Fix Errors button when scan is completed.
4) Restart your computer.
How does it work?
This tool will scan and diagnose, then repairs, your PC with patent
pending technology that fix your windows operating system registry
structure.
basic features: (repairs system freezing and rebooting issues , start-up customization , browser helper object management , program removal management , live updates , windows structure repair.)
License Issues
The troubleshooting instructions that follow describe the steps you can take if you install OrCAD and receive an error that is similar to one of the followi…
Tue, 1 Jun, 2021 at 11:14 AM
The “Cadence License Server Configuration Utility” is used to update licensing for OrCAD products. The instructions that follow explain how to update licens…
Tue, 1 Jun, 2021 at 11:18 AM
If OrCAD 17.2 launches properly and you receive an error when you attempt to launch 17.4, you need to contact EMA Design Automation at update@ema-eda.com&am…
Thu, 22 Jul, 2021 at 1:19 PM
If your server hostname was incorrectly entered during installation, you will be unable to launch Capture. The following error message reports this error. …
Tue, 1 Jun, 2021 at 11:51 AM
If you update your OrCAD licensing configuration and receive an error message that states, «Unable to restart Cadence License Server with new license f…
Tue, 1 Jun, 2021 at 11:54 AM
If you purchased and installed OrCAD 17.2 and have a Maintenance account, you may update your installation to OrCAD 17.4 if you request an updated OrCAD 17….
Tue, 1 Jun, 2021 at 11:56 AM
Question: How can I set up my Cadence License Manager so that idle licenses are timed out, recalled, and become available for another user? Answer: Timi…
Tue, 1 Jun, 2021 at 11:58 AM
The 30 day OrCAD Trial includes OrCAD Capture CIS, OrCAD PSpice Designer, OrCAD PCB Designer Professional, OrCAD Sigrity ERC, and more. If you have been gra…
Tue, 1 Jun, 2021 at 12:00 PM
Question How can I add an options file to my FlexNet license? Answer Options file pointers are added to the DAEMON line of a FlexNet license file as f…
Tue, 1 Jun, 2021 at 1:30 PM
Question Can I manually modify the product license file that EMA sent me? Answer Your license file generally consists of five line types listed belo…
Tue, 1 Jun, 2021 at 1:34 PM