Exposure lamp error перевод

Оборудование оснащено функцией самодиагностики. При обнаружении проблемы, аппарат блокируется, на дисплее отображается код вида С#### с указанием характера проблемы. Также появляется сообщение необходимости обслуживания. После устранения проблемы, ошибку можно сбросить тумблером питания, выключив и включив аппарат.

Код	Значение	Описание	Причина	Решение
C0030	FAX control PWB system error	Processing with the fax software was disabled due to a hardware problem.	Defective FAX control PWB.	Replace the FAX control PWB
C0070	FAX control PWB incompatible detection Error	Abnormal detection of FAX control PWB incompatibility In the initial communication with the FAX control PWB, any normal communication command is not transmitted.	Defective fax software. Defective FAX control PWB.	Install the fax software. Replace the FAX control PWB
C0100	Backup memory device error		Defective flash memory. Defective control PWB.	Replace the control PWB
C0120	MAC address data error		Defective flash memory.	Replace the control PWB
C0130	Backup memory read/write error		Defective flash memory. Defective control PWB	Replace the control PWB
C0140	Backup memory data error		Defective flash memory. Defective control PWB.	Replace the control PWB
C0150	Control PWB EEPROM error	Detecting control PWB EEPROM (U17) communication error.	Improper installation control PWB EEPROM (U17). Defective control PWB. Data damage of control PWB EEPROM (U17).	Check the installation of the EEPROM (U17) and remedy if necessary. Replace the control PWB.
C0170	Billing counting error		Defective control PWB. Data damage of control PWB EEPROM (U17).	Replace the control PWB
C0180	Machine number mismatch	Machine number of main and engine does not match.	The main PWB or the engine PWB were exchanged. Data damage of control PWB EEPROM (U17).	U004 Setting the machine number.
C0420	Paper feeder communication error	Communication error between control PWB and optional paper feeder.	Improper installation paper feeder. Defective harness between control PWB (YC30) and paper feeder interface connector, or improper connector insertion. Defective control PWB. Defective harness between PF main PWB (YC5) and paper feeder interface connector, or improper connector insertion. Defective PF mainPWB.	Follow installation instruction carefully again. Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness. Replace the control PWB. If none, remedy or replace the harness (Refer to the service manual for the paper feeder). Replace the PF main PWB (Refer to the service manual for the paper feeder).
C0830	FAX control PWB flash program area checksum error	A checksum error occurred with the program of the FAX control PWB.	Defective fax software. Defective FAX control PWB.	Install the fax software. Replace the FAX control PWB
C0840	Faults of RTC	The time is judged to go back based on the comparison of the RTC time and the current time or five years or more have passed.	Defective control PWB. The battery is disconnected from the control PWB.	Replace the control PWB. Check visually and remedy if necessary.
C0870	FAX control PWB to control PWB high capacity data transfer problem	High-capacity data transfer between the FAX control PWB and the control PWB of the machine was not normally performed even if the data transfer was retried the specified times.	Improper installation FAX control PWB. Defective FAX control PWB or control PWB.	Reinstall the FAX control PWB. Replace the FAX control PWB or control PWB and check for correct operation.
C0920	Fax file system error	The backup data is not retained for file system abnormality of flash memory of the FAX control PWB.	Defective FAX control PWB.	Replace the FAX control PWB.
C2000	Main motor error	The main motor ready input is not given for 2 s during the main motor is ON.	Defective harness between main motor (CN1) and control PWB (YC17), or improper connector insertion. Defective drive transmission system of the main motor. Defective main motor. Defective control PWB.	Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness. Check if the rollers and gears rotate smoothly. If not, grease the bushings and gears. Check for broken gears and replace if any. Replace the main motor. Replace the control PWB.
C2610	PF paper feed motor error (paper feeder)	The PF paper feed motor of cassette 2 ready input is not given for 2 s during the PF paper feed motor is ON.	Defective harness between PF paper feed motor and PF main PWB (YC4), or improper connector insertion. Defective PF paper feed motor drive transmission system. Defective PF main motor. Defective control PWB.	Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness (Refer to the service manual for the paper feeder). Check if the gears rotate smoothly. If not, grease the bushings and gears. Check for broken gears and replace if any. Replace the PF main motor. Replace the control PWB.
C2620	PF paper feed motor error (Paper feeder)	The PF paper feed motor of cassette 3 ready input is not given for 2 s during the PF paper feed motor is ON.	Defective harness between PF paper feed motor and PF main PWB (YC4), or improper connector insertion. Defective PF paper feed motor drive transmission system. Defective PF main motor. Defective control PWB.	Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness (Refer to the service manual for the paper feeder). Check if the gears rotate smoothly. If not, grease the bushings and gears. Check for broken gears and replace if any. Replace the PF main motor (Refer to the service manual for the paper feeder). Replace the control PWB.
C3100	ISU home position errorr.		Defective FFC between CCD PWB (YC1) and control PWB (YC8). Defective FFC between control PWB (YC6) and scanner PWB (YC103), or improper FFC insertion. Defective home position sensor. Defective harness between ISU motor and scanner PWB (YC104), or improper connector insertion. Defective ISU motor.	Replace the image scanner unit (ISU). Reinsert the FFC. Also check for continuity within the FFC. If none, remedy or replace the FFC. Replace the home position sensor. Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness. Replace the ISU motor.
C3200	Exposure lamp error	The exposure lamp is not turned on.	Defective FFC between scanner PWB (YC103) and control PWB (YC6), or improper FFC insertion. Defective FFC between CCD PWB (YC1) and control PWB (YC8). Defective harness between CCD PWB (YC3) and LED drive PWB (YC1), or improper connector insertion. Defective harness between LED drive PWB (YC2) and exposure lamp, or improper connector insertion. Defective exposure lamp.sensor. Defective LED drive PWB. Defective control PWB.	Reinsert the FFC. Also check for continuity within the FFC. If none, remedy or replace the FFC. Replace the image scanner unit (ISU). Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness. Replace the exposure lamp. Replace the LED drive PWB. Replace the control PWB.
C3300	AGC error	After AGC, correct input is not obtained at CCD.	Defective FFC between CCD PWB (YC1) and control PWB (YC8). Defective exposure lamp.sensor. Defective CCD PWB. Defective control PWB.	Replace the image scanner unit (ISU). Replace the exposure lamp. Replace the CCD PWB. Replace the control PWB.
C3500	CPU — ASIC (CCD PWB) communication error	An error code is detected.	Defective FFC between CCD PWB (YC1) and control PWB (YC8). Defective CCD PWB. Defective control PWB.	Replace the image scanner unit (ISU). Replace the CCD PWB. Replace the control PWB.
C4000	Polygon motor (laser scanner unit) error	The polygon motor ready input is not given for 6 s during the polygon motor is ON.	Defective harness between polygon motor and control PWB (YC10), or improper connector insertion. Defective laser scanner unit. Defective control PWB.	Reinsert the connector. Also check for continuity within the connector har- ness. If none, remedy or replace the harness. Replace the laser scanner unit. Replace the control PWB.
C4200	BD error (laser scanner unit) error		BD sensor does not detect laser beam due to condensation on the polygon mirror. Defective laser scanner unit. Defective control PWB.	Turn machine power off for at least 30 minutes, then turn machine on again. If not cured, replace the laser scanner unit. Replace the control PWB.
C4700	VIDEO ASIC device error	Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively.	Defective connector cable or poor contact in the connector. Defective control PWB.	Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Replace the control PWB.
C6000	Broken Fuser heater wire	The fuser temperature does not rise after the Fuser heater has been turned on.	Poor contact in the fuser thermistor connector terminals. Poor contact in the Fuser heater connector terminals. Fuser thermistor installed incorrectly. Fuser thermal cutout triggered. Fuser heater installed incorrectly. Broken Fuser heater wire.	Reinsert the connector. Replace the fuser unit.
C6020	Abnormally high fuser thermistor temperature	Fuser thermistor detects abnormally temperature. When the temperature of a fuser thermistor detects 195 °C or more at the time of heater OFF and 155 °C or more.	Shorted fuser thermistor. Defective control PWB.	Replace the fuser unit. Replace the control PWB.
C6030	Broken fuser thermistor wire	Input from fuser thermistor is 0 (A/D value).	Poor contact in the fuser thermistor connector terminals. Broken fuser thermistor wire. Fuser thermistor installed incorrectly. Fuser thermal cutout triggered. Fuser heater installed incorrectly. Broken Fuser heater wire.	Reinsert the connector. Replace the fuser unit.
C6400	Zero cross signal error	The zero cross signal does not reach the control PWB for specified time.	Defective harness between high voltage PWB (CN202) and control PWB (YC23), or improper connector insertion. Defective connection between power source PWB (YC103) and high voltage PWB (CN201). Defective power source PWB. Defective control PWB.	Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness. Reinsert the connector. Replace the power source PWB. Replace the control PWB.
C7990	Waste toner full	The waste toner sensor has detected that the waste toner reservoir (drum unit) is full.	Waste toner reservoir (drum unit) is full. Defective waste toner sensor. Defective control PWB.	Turn the power switch off/on to restart the machine. If the error is not resolved, replace the drum unit. Replace the waste toner sensor. Replace the control PWB.
F000	Control PWB — Operation panel PWB communication error		Defective harness between operation panel PWB (YC1) and control PWB (YC7), or improper connector insertion. motor is ON. Defective operation panel PWB. Defective control PWB.	Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness. Replace the operation panel PWB. Replace the control PWB.
F020	Control PWB RAM checksum error		Defective main memory (RAM) on the control PWB. Defective expanded memory (DIMM).	Turn the power switch off/on to restart the machine. If the error is not resolved, replace control PWB. Replace the expanded memory (DIMM).
F040	Control PWB engine communication error	A communication error is detected.	Defective control PWB.	Turn the power switch off/on to restart the machine. If the error is not resolved, replace control PWB.
F041	Control PWB — scanner PWB communication error	A communication error is detected.	Defective control PWB or scanner PWB.	Turn the power switch off/on to restart the machine. If the error is not resolved, replace control PWB or scanner PWB.
F050	Control PWB engine checksum error		Some error may have occurred when downloading the firmware of the control PWB. Defective control PWB.	Download the firmware of the control PWB again. Turn the power switch off/on to restart the machine. If the error is not resolved, replace control PWB.
F186	Control PWB video data control error		Defective control PWB.	Turn the power switch off/on to restart the machine. If the error is not resolved, replace control PWB.

При использовании любой техники время от времени могут возникать неполадки. Так, например, при использовании копиров, принтеров и МФУ Sharpмогут появляться различные ошибки, вызванные различными причинами. Об их возникновении пользователь информируется с помощью кода, которые выводится на дисплее принтера или другого используемого устройства. Коды ошибок Sharp вы можете идентифицировать с помощью приведенной ниже таблицы.  Выяснив причину сбоя в работе устройства, вы сможете устранить ее самостоятельно (например, если произошло замятие бумаги, отсутствует бумага в лотке) либо обратиться в сервисный центр по обслуживанию и ремонту Sharp, если код ошибки сообщает о серьезной поломке.

Sharp AL-840

Код ошибки	Подкод	Описание
L1	00	Неисправность при движении сканирующего устройства
L3	00	Неисправность сканирующего устройства при возвращении в начальное положение
Е7	03	Неисправность, связанная с яркостью свечения лазера
04	Ошибка при определении уровня белого при выполнении штриховки
05	Ошибка при определении уровня черного при выполнении штриховки
12	Ошибка уровня выходного сигнала при выполнении штриховки
14	Сбой ASIC (MCU PWB)
15	Неисправность копировальной лампы
H2	00	Неисправность термодатчика
H3	00	Температура вала узла закрепления превысила норму
H4	00	Температура вала узла закрепления опустилась ниже положенного уровня
U2	01	Неисправность EEPROM (MCU PWB) (ошибка данных счетчика)
04	Неисправность EEPROM (MCU PWB) (ошибка записи/чтения)
05	Неисправность EEPROM (MCU PWB)
06	Неисправность ROM (MCU PWB)
C1		Неисправность, обнаруженная выключателем передней панели (блока питания)
CH		Отсутствует тонер-картридж
E1		Замятие бумаги при подаче из лотка
E2		Замятие бумаги
E3		Замятие бумаги на выходе узла закрепления
P		Отсутствие бумаги в лотке

Sharp AL-1000

Код ошибки	Подкод	Описание
E7	03	Неисправность блока лазера, связанная с излучающим диодом и его цепями
04	Ошибка при определении уровня белого при выполнении штриховки
05	Ошибка при определении уровня черного при выполнении штриховки
12	Ошибка уровня выходного сигнала при выполнении штриховки
14	Сбой ASIC (MCU PWB)
15	Неисправность копировальной лампы
L1	00	Неисправность при движении сканирующего устройства (датчик начального положения сканирующего устройства не видит движения зеркал)
L3	00	Неисправность сканирующего устройства при возвращении в начальное положение (сканер не успел вернутся в начальное положение за определенное время)
L4	01	Main motor drive overloaded
L6	10	Неисправность двигателя многогранника блока лазера (полигон-мотор)
H2	00	Неисправность термодатчика
H3	00	Температура вала узла закрепления превысила норму
H4	00	Температура вала узла закрепления опустилась ниже положенного уровня
U2	01	Неисправность EEPROM (MCU PWB) (ошибка данных счетчика)
04	Неисправность EEPROM (MCU PWB) (ошибка записи/чтения)
CH		Отсутствует тонер-картридж

Sharp AL-1010

Код ошибки	Подкод	Описание
E7	03	Scanner position error
04	Exposure lamp blown
05	CCD calibration error
12	White level calibration error
14	Main board malfunction
15	Exposure lamp blown
L1	00	Scanner position error
L3	00	Scanner position error
L4	01	Main motor drive overloaded
L6	10	Polygon mirror motor not up to speed
H2	00	Fusing unit temperature error
H3	00	Overheated fusing unit
H4	00	The fusing unit doesn’t heat up
U2	01	Counter error
04	EPROM error
CH blinking		Dev unit is not properly installed

Sharp AR-160 / 161

Код ошибки	Подкод	Описание
CC		Original not detected
E1	00	Lost communication with the Sorter
10	Lost communication with the Sorter
11	ASIC error
12	Image Processing Unit error
13	ROM error
14	NVRAM error
15	Page memory fault
16	SIMM not present or installed incorectly
17	Page rotation error in RAM
80	Electronic sort board error
81
82
84
88
E7	03	Lens position error
04	White level calibration error
05	Black level calibration error
12	CCD calibration error
F1	06	Shift sort motor overloaded
F5	02	Exposure lamp blown
F6	00	Fax board problems
10
80
81
82
84
88
F9	00	Printer board problems
10
80
81
82
84
88
H2	00	Fusing unit temperature error
H3	00	Overheated fusing unit
H4	00	The fusing unit doesn’t heat up
L1	00	Scanner position error
L3	00	Scanner position error
L4	01	Main motor drive overloaded
10	Separation motor overloaded
L6	10	Polygon mirror motor not up to speed
L8	01	Zero cross signal error
U2	04	EPROM error
11	Main counter error
12	EPROM error
U3	29	Mirror position error
U9	00	Op panel problem
81
82
84
88
U95		Firmware error

Sharp AR-163 / 201 / 206 / 5015 / 5020

Код ошибки	Подкод	Описание
E1	00	Неисправность связи с платой электронного сортировщика
10	Неисправность платы электронного сортировщика
11	Ошибка ASIC электронного сортировщика
12	Ошибка CODEC электронного сортировщика
13	Ошибка очистки (сброса) ROM электронного сортировщика
14	Ошибка RAM электронного сортировщика
15	Ошибка сохранения страницы в памяти электронного сортировщика
16	Ошибка SIMM электронного сортировщика
17	Ошибка RAM
80	Неисправность связи с платой электронного сортировщика (PROTOCOL)
81	Неисправность связи с платой электронного сортировщика (PARITY)
82	Неисправность связи с платой электронного сортировщика (OVERRUN)
84	Неисправность связи с платой электронного сортировщика (FRAMING)
88	Неисправность связи с платой электронного сортировщика (TIME-OUT)
E7	03	Неисправность блока лазера
04	Ошибка определения уровня белого CCD
05	Ошибка при определении уровня черного CCD
F1	06	Неисправность Shifter (двигателя сдвига копии)
F2	04	Ошибка чтения данных CRUM (чипа тонер-картриджа)
F5	02	Неисправность копировальной лампы
F6	00	Ошибка связи с платой факса
10	Неисправность платы факса
80	Ошибка связи с платой факса (PROTOCOL)
81	Ошибка связи с платой факса (PARITY)
82	Ошибка связи с платой факса (OVERRUN)
84	Ошибка связи с платой факса (FRAMING)
88	Ошибка связи с платой факса (TIME-OUT)
F9	00	Ошибка связи с платой принтера
10	Неисправность платы принтера
80	Ошибка связи с платой принтера (PROTOCOL)
81	Ошибка связи с платой принтера (PARITY)
82	Ошибка связи с платой принтера (OVERRUN)
84	Ошибка связи с платой принтера (FRAMING)
88	Ошибка связи с платой принтера (TIME-OUT)
H2	00	Неисправность термодатчика
H3	00	Температура вала узла закрепления превысила норму
H4	00	Температура вала узла закрепления опустилась ниже положенного уровня
L1	00	Обнаружена неисправность при определении начального положения сканирующей каретки
L3	00	Обнаружена неисправность при обратном ходе сканирующей каретки
L4	01	Неисправность главного двигателя
10	Неисправность двигателя сепаратора
L6	10	Неисправность двигателя многогранника блока лазера (полигон-мотор)
L8	01	Ошибка сигнала пересечения нуля
U2	04	EEPROM serial communication error
11	counter check sum error
12	adjustment value check sum error(EEPROM)
40	CRUM communication error
U3	29	Ошибка в определении начального положения зеркал
U9	00	Ошибка связи с панелью управления (PROTOCOL)
80	Ошибка связи с панелью управления (PARITY)
82	Ошибка связи с панелью управления (OVERRUN)
84	Ошибка связи с панелью управления (FRAMING)
88	Ошибка связи с панелью управления (TIME-OUT)
U95		Неисправность соединения платы управления
U99

Sharp AR-405

Код ошибки	Подкод	Описание
C1	00	MC unit malfunction
C2	00	TC unit malfunction
E7	00	Image Processing Unit error
01	Memory back-up battery dead
02	Laser unit problem
03	HDD defective
10	black level calibration error
11	white level calibration error
13	CCD calibration error
90	Image Processing Unit error
F1	00	Lost communication with the Sorter
01	Sorter registration problem
02	Paper transport motor overloaded in sorter
04	Bin position error in sorter
05	Bin position error in sorter
06	Shift sort motor overloaded
08	Stapler position error
08	Stapler overloaded
11	Sorter problems
14	Second shift tray jammed
15	Sorter drive problems
50	Sorter not installed properly
80	No powerin sorter
F2	00	ID pattern reading error
02	Toner add mechanism malfunction
31	ID pattern reading error
32	ID pattern reading error
39	Drum thermistor error
F3	12	Paper does not lift in the tray
22	Paper does not lift in the tray
F9	00	Printer board problems
01	Printer board problems
02	Printer board problems
03	Network card error
04	Firmware error
05	Not enough memory
10	Printer board problems
90	Printer board problems
H2	00	Fusing unit temperature error
01	Fusing unit temperature error
H3	00	Overheated fusing unit
01	Overheated fusing unit
H4	00	The fusing unit doesn’t heat up
01	The fusing unit doesn’t heat up
H5	01	Papersensordefective in the fusing unit
02	Fusing unit temperature error
L1	00	Scanner position error
L3	00	Scanner position error
L4	01	Main motor drive overloaded
L6	10	Polygon mirror motor not up to speed
L8	01	Zero cross signal error
02	Zero cross signal error
U2	00	EPROM error
11	EPROM error
U4	02	Duplex not working properly
03	Duplex problems
U5	00	Communication with the ADF is lost
01	Registration sensor problem in ADF
02	Exit sensor error in ADF
03	Timing sensor problems in ADF
11	Paper feed drive overloaded in ADF
U6	01	Paper lift problem in 1’st optional tray
02	Paper lift problem in 2’nd optional tray
08	Paper feed unit without power
10	PFU paper transport motor overloaded
22	Paper feed unit without power
50	Paper feed unit not installed properly
51	LCT not installed properly
U7	00	Main board malfunction
U9	00	Op panel problem
90	Op panel problem
EE	EU	Low toner density in the developer
EE	EL	High toner density in the developer
FA	01	Memory back-up battery dead
PC		Key counter not installed

Код ошибки Описание ошибки Причина ошибки 0030 FAX control PWB system error
Processing with the fax software was disabled due to a hardware problem. Defective FAX control PWB. 0060 Engine PWB type error Defective engine sub PCB. 0070 FAX control PWB incompatible detection error
Abnormal detection of FAX control PWB incompatibility In the initial communication with the FAX control PWB, any normal communication command is not transmitted. Defective FAX software
Defective FAX control PWB. 0100 Backup memory device error Defective flash memory. 0120 MAC address data error
For data in which the MAC address is invalid. Defective main PWB.
Defective flash memory.
Defective engine PWB. 0130 Backup memory read/write error (main PWB) Defective flash memory.
Defective main PWB. 0140 Backup memory data error (main PWB) Defective flash memory.
Defective main PWB. 0150 Backup memory read/write error (engine PWB)
Detecting engine PWB EEPROM communication error. Improper installation engine PWB EEPROM.
Defective engine PWB.
Device damage of EEPROM. 0160 Backup memory data error (engine PWB) Defective flash memory.
Defective engine PWB. 0170 Billing counting error
A checksum error is detected in the main and engine backup memories for the billing counters. Data damage of EEPROM.
Defective PWB. 0180 Machine number mismatch
Machine number of main and engine does not match. Data damage of EEPROM. 0320 I/O CPU communication error
A communication error is detected 10 times in succession. Defective PWB. 0630 DMA error DMA transmission of image data does not complete within the specified period of time. Poor contact in the connector terminals. Defective main PWB. 0800 Image processing error
JAM05 is detected twice. Defective main PWB. 0830 FAX control PWB flash program area checksum error
A checksum error occurred with the program of the FAX control PWB. Defective FAX software.
Defective FAX control PWB. 0840 Faults of RTC
The time is judged to go back based on the comparison of the RTC time and the current time or five years or more have passed. The battery is disconnected from the main PWB.
Defective main PWB. 0870 FAX control PWB to main PWB high capacity data transfer error
High-capacity data transfer between the FAX control PWB and the main PWB of the machine was not normally performed even if the data transfer was retried the specified times. Improper installation FAX control PWB.
Defective FAX control PWB or main PWB. 0920 Fax file system error
The backup data is not retained for file system abnormality of flash memory of the FAX control PWB. Defective FAX control PWB. 1010 Lift motor error
After cassette 1 is inserted, lift sensor does not turn on within 12 s. This error is detected four times successively. Defective bottom plate elevation mechanism in the cassette.
Defective connector cable or poor contact in the connector.
Defective drive transmission system of the lift motor.
Defective lift motor.
Defective engine PWB. 1020 PF lift motor error (paper feeder)
After cassette 2 is inserted, PF lift sensor 1 does not turn on within 12 s. This error is detected four times successively. Defective bottom plate elevation mechanism in the cassette.
Defective connector cable or poor contact in the connector.
Defective drive transmission system of the PF lift motor 1.
Defective PF lift motor 1.
Defective PF main PWB. 1030 PF lift motor error (paper feeder)
After cassette 3 is inserted, PF lift sensor 2 does not turn on within 12 s. This error is detected four times successively. Defective bottom plate elevation mechanism in the cassette.
Defective connector cable or poor contact in the connector.
Defective drive transmission system of the PF lift motor 2.
Defective PF lift motor 2.
Defective PF main PWB. 1800 Paper feeder communication error
A communication error is detected 10 times in succession. Improper installation paper feeder.
Defective connector cable or poor contact in the connector.
Defective engine PWB.
Defective PF main PWB. 1900 Paper feeder EEPROM error
When writing the data, the write data and the read data is not continuously in agreement 5 times. Defective PF main PWB.
Device damage of EEPROM. 2000 Main motor steady-state error
Stable OFF is detected for 1 s continuously after main motor stabilized. Defective connector cable or poor contact in the connector.
Defective drive transmission system of the main motor.
Defective main motor.
Defective engine PWB. 2010 Main motor drive error
The main motor is not stabilized within 2 s after driving starts. Defective connector cable or poor contact in the connector.
Defective drive transmission system of the main motor.
Defective main motor.
Defective engine PWB. 2101 Developer motor K steady-state error
The rated speed signal detected the stability OFF continuously for 1 s after the developer motor K stabilizes. Defective connector cable or poor contact in the connector.
Defective drive transmission system.
Defective motor.
Defective PWB. 2102 Developer motor YCM steady-state error
The rated speed signal detected the stability OFF continuously for 1 s after the developer motor YCM stabilizes. Defective connector cable or poor contact in the connector.
Defective drive transmission system.
Defective motor.
Defective PWB. 2111 Developer motor K startup error
Developer motor K is not stabilized within 2 s since the motor is activated. Defective connector cable or poor contact in the connector
Defective drive transmission system.
Defective motor.
Defective PWB. 2112 Developer motor YCM startup error
Developer motor YCM is not stabilized within 2 s since the motor is activated. Defective connector cable or poor contact in the connector
Defective drive transmission system.
Defective motor.
Defective PWB. 2300 Fuser motor steady-state error
The rated speed signal detected the stability OFF continuously for 1 s after the fuser motor stabilizes. Defective connector cable or poor contact in the connector.
Defective drive transmission system.
Defective motor.
Defective PWB. 2310 Fuser motor startup error
Fuser motor is not stabilized within 2 s since the motor is activated. Defective connector cable or poor contact in the connector.
Defective drive transmission system.
Defective motor.
Defective PWB. 2550 Conveying motor steady-state error
The rated speed signal detected the stability OFF continuously for 1 s after the conveying motor stabilizes. Defective connector cable or poor contact in the connector.
Defective drive transmission system.
Defective motor.
Defective PWB. 2560 Conveying motor startup error
Conveying motor is not stabilized within 2 s since the motor is activated. Defective connector cable or poor contact in the connector.
Defective drive transmission system.
Defective motor.
Defective PWB. 2600 PF drive motor error (paper feeder)
When the PF drive motor is driven, error signal is detected continuously for 1 s. Defective connector cable or poor contact in the connector.
Defective drive transmission system of the PF drive motor.
Defective PF drive motor.
Defective PF main PWB. 2700 TC belt motor error
When the TC belt motor is driven, error signal is detected continuously for 1 s. Defective connector cable or poor contact in the connector.
Defective drive transmission system of the PF drive motor.
Defective PF drive motor.
Defective PF main PWB. 3100 ISU home position error
The home position is not correct when the power is turned on or at the start of copying using the table. Defective connector cable or poor contact in the connector.
Defective home position sensor.
Defective ISU motor.
Defective CCD PWB.
Defective engine PWB. 3200 Exposure lamp error
When input value at the time of exposure lamp illumination does not exceed the threshold value between 5 s. Defective connector cable or poor contact in the connector.
Defective exposure lamp.
Defective CCD PWB.
Defective main PWB. 3500 Communication error between scanner and ASIC
An error code is detected 3 times in succession. Defective connector cable or poor contact in the connector.
Defective CCD PWB.
Defective main PWB. 3600 Scanner sequence error Defective main PWB or engine PWB. 4000 Polygon motor synchronization error
The polygon motor is not stabilized within 10 s after driving starts. Defective connector cable or poor contact in the connector.
Defective polygon motor.
Defective engine PWB. 4001 Polygon motor (K) steady-state error
The rated speed signal detected the stability OFF continuously for 1 s after the polygon motor (K) stabilizes. Defective connector cable or poor contact in the connector.
Defective motor
Defective PWB. 4002 Polygon motor (С) steady-state error
The rated speed signal detected the stability OFF continuously for 1 s after the polygon motor (С) stabilizes. Defective connector cable or poor contact in the connector.
Defective motor
Defective PWB. 4003 Polygon motor (M) steady-state error
The rated speed signal detected the stability OFF continuously for 1 s after the polygon motor (M) stabilizes. Defective connector cable or poor contact in the connector.
Defective motor
Defective PWB. 4004 Polygon motor (Y) steady-state error
The rated speed signal detected the stability OFF continuously for 1 s after the polygon motor (Y) stabilizes. Defective connector cable or poor contact in the connector.
Defective motor
Defective PWB. 4010 Polygon motor steady-state error
Stable OFF is detected for 1 s continuously after polygon motor stabilized. Defective connector cable or poor contact in the connector.
Defective polygon motor.
Defective engine PWB. 4011 Polygon motor (K) startup error
Polygon motor (K) is not stabilized within 10 s since the motor is activated. Defective connector cable or poor contact in the connector.
Defective motor.
Defective PWB. 4012 Polygon motor (C) startup error
Polygon motor (C) is not stabilized within 10 s since the motor is activated. Defective connector cable or poor contact in the connector.
Defective motor.
Defective PWB. 4013 Polygon motor (M) startup error
Polygon motor (M) is not stabilized within 10 s since the motor is activated. Defective connector cable or poor contact in the connector.
Defective motor.
Defective PWB. 4014 Polygon motor (Y) startup error
Polygon motor (Y) is not stabilized within 10 s since the motor is activated. Defective connector cable or poor contact in the connector.
Defective motor.
Defective PWB. 4100 BD initialization error
BD is not detected within 1 s after polygon motor stabilized. Defective connector cable or poor contact in the connector.
Defective APC PWB.
Defective BD PWB.
Defective main PWB. 4600 LSU cleaning motor error
When the LSU cleaning motor is driven, an error signal is detected continuously for 1 s. Defective connector cable or poor contact in the connector.
Defective drive transmission system.
Defective motor. Defective PWB. 4700 VIDEO ASIC device error Defective connector cable or poor contact in the connector.
Defective main PWB or engine PWB. 4950 LSU CPU communication error
A communication error is detected 10 times in succession. Defective connector cable or poor contact in the connector.
Defective PWB. 6000 Broken fuser heater wire
The detected temperature of fuser thermistor does not reach the specified temperature (ready indication temperature) after the fuser heater has been turned on continuously for 60 s in warming up. The fusing temperature at 7 seconds and 20 seconds since fuser temperature control has occurred differs by 43°C/109.4°F or less. Defective connector cable or poor contact in the connector.
Deformed connector pin.
Defective triac.
Fuser thermostat triggered.
Broken fuser heater wire.
Defective engine PWB. 6000
6020
6030
6050 Broken fuser heater wire
Abnormally high fuser thermistor temperature Broken fuser thermistor wire Abnormally low fuser thermistor temperature Deformed connector pin.
Defective triac. 6020 Abnormally high fuser thermistor temperature
The fuser thermistor detects a temperature higher than 230°C/446°F continuously for 40 ms. High fuser temperature signal detects a temperature of 255°C/491°F continuously for 40 ms. Deformed connector pin.
Defective triac.
Shorted fuser thermistor.
Defective engine PWB. 6030 Broken fuser thermistor wire
A/D value of the fuser thermistor exceeds 251 bit continuously for 7 s during warming up. Defective connector cable or poor contact in the connector.
Deformed connector pin.
Defective triac.
Defective fuser thermistor.
Defective engine PWB 6050 Abnormally low fuser thermistor temperature
As the stable temperature has reached the second time, the decrease in the fuser thermistor temperature of 60°C/140°F or greater is detected for one second. Deformed connector pin.
Defective triac.
Defective fuser thermistor
Defective fuser heater.
Defective engine PWB. 6120 Abnormally high fuser thermistor 3 (press roller) temperature
The fuser temperature exceeds 200 °C/392 °F for 1 s. Deformed connector pin.
Defective IH PWB.
Defective fuser thermistor.
Defective engine PWB. 6130 Fuser thermistor 3 (press roller) break error Fuser thermistor 3 detects a temperature of -14 °C/6.8 °F . Fuser thermistor 3 does not reach 30° C/86 °F even after20 s during warming up. Defective connector cable or poor contact in the connector
Deformed connector pin.
Defective IH PWB.
Defective fuser thermistor.
Defective engine PWB. 6150 Abnormally low fuser thermistor 3 (press roller) temperature
The fuser temperature lower than 30 °C/86 °F is detected continuously for 1 s. Deformed connector pin.
Defective fuser thermistor
Defective fuser heater.
Defective engine PWB. 6200 Broken fuser edge heater wire
Fuser thermistor 1 does not reach 50° C/122 °F even after20 s during warming up. The detected temperature of fuser thermistor1 does not reach the specified temperature (ready indication temperature) for 20 s in warming up after reaching 50° C/122 °F. Defective connector cable or poor contact in the connector.
Deformed connector pin.
Fuser thermostat triggered.
Broken fuser heater wire.
Defective engine PWB. 6220 Abnormally high fuser thermistor 1 (edge) temperature
The fuser temperature exceeds 240 °C/464 °F for 1 s Defective connector cable or poor contact in the connector.
Deformed connector pin.
Fuser thermostat triggered.
Broken fuser heater wire.
Defective engine PWB. 6230 Fuser thermistor 1 (edge) break error
During warming up a hearter, fuser thermistor 2 detects a temperature of 100 °C/212 °F or higher and, fuser thermistor 1 detects a temperature of 37 °C/99 °F or lower. Defective connector cable or poor contact in the connector.
Deformed connector pin.
Fuser thermostat triggered.
Broken fuser heater wire.
Defective engine PWB. 6250 Abnormally low fuser thermistor 1 (edge) temperature
The fuser temperature lower than 100 °C/212 °F is detected continuously for 1 s during printing. The fuser temperature lower than 50 °C/122 °F is detected continuously for 1 s during pre-heating. Defective connector cable or poor contact in the connector.
Deformed connector pin.
Fuser thermostat triggered.
Broken fuser heater wire.
Defective engine PWB. 6400 Zero-cross signal error
While fuser heater control is performed, the zero-cross signal is not input within 3 s. Defective connector cable or poor contact in the connector
Defective power source PWB or engine PWB. 6410 Fuser unit type mismatch problem
Absence of the fuser unit is detected. Fuser unit connector inserted incorrectly.
Different type of the fuser unit is installed. 6600 Belt rotation error
The belt was detected to stop for 1 s continuously during motor remote is on. Defective fuser motor.
Defective IH belt.
Defective IH PWB.
Defective engine PWB. 7101 Toner sensor K error Defective Developer unit.
Defective PWB. 7102 Toner sensor C error Defective Developer unit.
Defective PWB. 7103 Toner sensor M error Defective Developer unit.
Defective PWB. 7104 Toner sensor Y error Defective Developer unit.
Defective PWB. 7401 Developing unit K type mismatch problem
Absence of the developing unit K is detected. Developing unit connector inserted incorrectly.
Different type of the developing unit is installed.
Defective PWB. 7402 Developing unit C type mismatch problem
Absence of the developing unit C is detected. Developing unit connector inserted incorrectly.
Different type of the developing unit is installed.
Defective PWB. 7403 Developing unit M type mismatch problem
Absence of the developing unit M is detected. Developing unit connector inserted incorrectly.
Different type of the developing unit is installed.
Defective PWB. 7404 Developing unit Y type mismatch problem
Absence of the developing unit Y is detected. Developing unit connector inserted incorrectly.
Different type of the developing unit is installed.
Defective PWB. 7411 Drum unit K type mismatch problem
Absence of the drum unit K is detected. Drum unit connector inserted incorrectly.
Different type of the drum unit is installed.
Defective PWB. 7412 Drum unit C type mismatch problem
Absence of the drum unit C is detected. Drum unit connector inserted incorrectly.
Different type of the drum unit is installed.
Defective PWB. 7413 Drum unit M type mismatch problem
Absence of the drum unit M is detected. Drum unit connector inserted incorrectly.
Different type of the drum unit is installed.
Defective PWB. 7414 Drum unit Y type mismatch problem
Absence of the drum unit Y is detected. Drum unit connector inserted incorrectly.
Different type of the drum unit is installed.
Defective PWB. 7420 Transfer belt unit type mismatch problem
Absence of the transfer belt unit is detected. Transfer belt unit connector inserted incorrectly.
Different type of the transfer belt unit is installed.
Defective PWB. 7601 ID sensor 1 (front) error Defective ID sensor.
Defective PWB. 7602 ID sensor 2 (rear) error Defective ID sensor.
Defective PWB. 7611 ID sensor (K) density error
When ID sensor 2 detected CTD is 500 or less. Defective ID sensor.
Defective PWB. 7612 ID sensor (C) density error
When ID sensor 2 detected CTD is 500 or less. Defective ID sensor.
Defective PWB. 7613 ID sensor (M) density error
When ID sensor 2 detected CTD is 500 or less. Defective ID sensor.
Defective PWB. 7614 ID sensor (Y) density error
When ID sensor 2 detected CTD is 500 or less. Defective ID sensor.
Defective PWB. 7620 ID sensor timing error
Color registration correction was failed. Defective ID sensor.
Defective PWB. 7800 Broken external thermistor wire
The thermistor output value is 0.3 V or less. Defective connector cable or poor contact in the connector.
Defective temperature sensor. 7810 Short-circuited external thermistor wire
The thermistor output value is 3 V or more. Defective connector cable or poor contact in the connector.
Defective temperature sensor. 7900 Drum unit EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively. Defective connector cable or poor contact in the connector.
Defective drum unit. 7901 Drum K EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively. Defective connector cable or poor contact in the connector.
Defective drum unit. 7902 Drum C EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively. Defective connector cable or poor contact in the connector.
Defective drum unit. 7903 Drum M EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively. Defective connector cable or poor contact in the connector.
Defective drum unit. 7904 Drum Y EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively. Defective connector cable or poor contact in the connector.
Defective drum unit. 7910 Developer unit EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively. Defective connector cable or poor contact in the connector.
Defective developer unit. 7911 Developing unit K EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively. Poor contact in the connector terminals.
Defective developing PWB. 7912 Developing unit C EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively. Poor contact in the connector terminals.
Defective developing PWB. 7913 Developing unit M EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively. Poor contact in the connector terminals.
Defective developing PWB. 7914 Developing unit Y EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively. Poor contact in the connector terminals.
Defective developing PWB. 8030 Tray upper limit detection problem (document finisher)
When the tray elevation motor raises a tray, the ON status of the tray upper limit sensor is detected. Defective connector cable or poor contact in the connector.
Defective tray upper limit sensor, paper surface sensor 1/2.
Defective DF main PWB. 8040 Belt problem (document finisher)
The belt sensor does not turn on/off within specified time of the belt solenoid turning on. Defective connector cable or poor contact in the connector.
Defective belt sensor.
Defective belt solenoid.
Defective DF main PWB. 8140 Tray elevation motor problem (document finisher)
The tray low limit sensor or paper surface sensor 1/2 cannot be detected to be on within 10 s since the tray elevation motor is activated. Defective connector cable or poor contact in the connector.
Defective connector cable or poor contact in the connector.
The tray elevation motor malfunctions.
Defective tray lower limit sensor, paper surface sensor 1/2.
Defective DF main PWB. 8210 Stapler problem (document finisher)
Jam 7012 or 7023 is indicated. Defective connector cable of staple or poor contact in the connector.
The stapler is blocked with a staple.
The stapler is broken
Defective DF main PWB. 8320 Adjustment motor 2 problem (document finisher)
The adjustment sensor 2 does not turn on/off within specified time of the adjustment motor 2 turning on. Defective connector cable or poor contact in the connector.
Defective adjustment sensor 2.
Defective adjustment motor 2.
Defective DF main PWB. 8330 Adjustment motor 1 problem (document finisher)
The adjustment sensor 1 does not turn on/off within specified time of the adjustment motor 1 turning on. Defective connector cable or poor contact in the connector.
Defective adjustment sensor 1.
Defective adjustment motor 1. 8350 Roller motor problem (document finisher)
The roller sensor does not turn on/off within specified time of the roller motor turning on. Defective DF main PWB.
Defective connector cable or poor contact in the connector.
Defective roller sensor.
Defective roller motor.
Defective DF main PWB. 8360 Slide motor problem (document finisher)
The slide sensor does not turn on/off within specified time of the slide motor turning on. Defective connector cable or poor contact in the connector.
Defective slide sensor.
Defective slide motor.
Defective DF main PWB. 8460 EEPROM problem (document finisher)
Reading from or writing to EEPROM cannot be performed. Defective EEPROM or DF main PWB. 8800 Document finisher communication error
A communication error is detected 10 times in succession. Defective connector cable or poor contact in the connector
Defective DF main PWB.
Defective engine PWB. 8830 Bridge communication error (document finisher)
A communication error is detected 10 times in succession. Defective connector cable or poor contact in the connector.
Defective bridge PWB.
Defective engine PWB. 8990 Document finisher communication error Defective connector cable or poor contact in the connector.
Defective DF main PWB.
Defective bridge PWB. 9000 Document processor communication error
A communication error is detected 10 times in succession. Defective connector cable or poor contact in the connector.
Defective DP main PWB. 9060 DP EEPROM error Read and write data does not match. Data in the specified area of the backup memory does not match the specified values. Defective DP main PWB.
Device damage of EEPROM. 9500 BRU communication error IPU PWB error 9510 BRU PWB error IPU PWB error 9520 BRU PWB data error IPU PWB error F000 Main PWB — operation panel PWB communication error Defective main PWB.
Defective operation panel PWB. F010 Main PWB checksum error Defective main PWB. F040 Main PWB — print engine communication error Defective main PWB.
Defective engine PWB. F050 Print engine ROM checksum error Defective engine PWB.

1. печать, печатание

2. фотографическое копирование; копирование на формную пластину

3. печатное издание

4. тираж

5. полиграфия, полиграфическая промышленность

6. различные сорта печатной бумаги

printing two-up — печатание двойников, параллельное печатание с двух одинаковых форм

printing verse — печатание на обороте, запечатывание оборотной стороны

arc printing — дуговая печать, печатание с помощью электрической дуги

7. печатание на оборотной стороне прозрачной плёнки

bichromate printing — печатание с форм, изготовленных с использованием хромированных коллоидов

8. печатание голубой краской; светокопирование

9. изготовление синих копий, изготовление «синек»

10. печатание на картонных заготовках; печатание на картоне

11. производство картонных упаковок

code printing — печатание кодовых меток, печатание кодовых знаков, кодирование, шифрование

12. цветная печатная бумага

color process printing — многокрасочное печатание с форм, изготовленных фотомеханическим способом

13. контактная печать

14. контактное копирование

printing lamp — лампа для копирования, копировальная лампа

15. печатание издания в нескольких вариантах с учётом интересов потребителей

16. печатание по требованию одного экземпляра издания

17. прямое контактное копирование

18. прямая печать

19. печатание с первичной формы

20. печатание изобразительной продукции

21. печатание на прозрачном материале

dot-in-dot printing — печатание с точной приводкой, печатание «точка в точку»

22. двукратное запечатывание

23. комбинирование деталей двух разных негативов на одном позитиве или печатной форме

duotone printing — печатание двухкрасочных репродукций с одноцветного оригинала, дуплекс-автотипия

ferromagnetic printing — печатание ферромагнитными красками, магнитографская печать, магнитография

flat-bed printing — печатание на плоскопечатных машинах, печатание с плоских форм высокой печати

form skip printing — печатание формуляров с пропусками отдельных пунктов на последовательно идущих страницах

24. четырёхкрасочная печать

25. печатание в четыре краски

26. многокрасочная печать всеми основными красками

27. нанесение клеевого слоя

28. гуммирование

heat-set printing — печатание красками, закрепляющимися под действием нагрева

hot foil printing — горячее тиснение фольгой, тиснение фольгой с использованием нагретого штампа

29. переводной способ копирования

30. печатание через промежуточную поверхность; офсетная печать

31. ведомственная печать

32. внутрифирменная печать

33. печатание литографским способом, литография

34. офсетная печать

magnetic ink printing — печатание магнитными красками, магнитографская печать, магнитография

35. картографическая печать, картопечатание

36. производство картографической продукции

37. копирование изображения на металлическую пластину

38. печатание на металле

39. акцидентная печать

40. печатание акцидентной продукции

41. однокрасочная печать

42. печатание однокрасочной продукции

43. многокрасочная печать

44. печатание многокрасочной продукции

45. печатание газетно-журнальной продукции

46. газетно-журнальное производство

47. печатание газет

48. газетное производство

49. распечатка информации, хранящейся в базе данных вычислительной системы по требованию

50. печатание по требованию

51. печатание персонализированных изданий

52. оптическая печать

53. проекционное копирование

54. печатание на упаковочных материалах

55. производство упаковки

56. фотография

57. фотопечать; копирование

58. глубокая печать

59. печатание с гелиогравюр

60. печатание с форм, изготовленных фотомеханическим способом

61. фотомеханический способ размножения

62. печатание с гравированных медных пластин

63. печатание вкладных иллюстраций

process printing — многокрасочная печать с форм, изготовленных фотомеханическим способом

64. печатание издательской продукции

65. заключительная стадия печатания

raised printing — печатание с последующим оплавлением рельефа; рельефная печать

66. рефлексное копирование

67. рефлексное печатание

68. печатание с выворотных форм

69. печатание с реверсивным приводом цилиндров; реверсивное печатание

70. печатание на обороте, запечатывание оборотной стороны

rotary printing — ротационная печать, печатание на ротационных машинах

71. печатание многокрасочных газет «по сырому»

72. цветные краски для печатания газет

73. растровая печать

74. второй завод, допечатка

75. второй прогон

selective printing — избирательное печатание, печатание с избирательным воспроизведением знаков

76. малотиражная печать

77. малотиражное копирование

small offset printing — «малый офсет», печатание малоформатной продукции офсетным способом

solid printing — печатание со сплошных форм, печатание плашек

solid color printing — печатание со сплошных форм цветными красками, печатание цветных плашек

78. трафаретная печать

79. ротаторная печать

test printing — пробное печатание, изготовление пробных оттисков

thermal printing — термопечать, термографская печать, термография; печатание термокрасками

thermographic printing — термопечать, термографская печать, термография, печатание термокрасками

three-color process printing — трёхкрасочная печать с цветоделённых печатных форм, изготовленных фотомеханическим способом

80. печатание на тканях

81. печатание на тонкой бумаге

82. декалькомания, печатание переводных изображений

83. печатание с переносом изображения

web printing — печатание на рулонном материале, рулонная печать

Exposure errors.: перевод, синонимы, произношение, примеры предложений, антонимы, транскрипция