Fatal simulation error encountered proteus 8

How to Solve “Fatal simulation error encountered”?

By inham

As an affiliate, we may earn a commission from qualifying purchases. We get commissions for purchases made through links on this website from Amazon.

”Fatal simulation error encountered” you might have faced this error while performing simulation in Proteus. I have read many articles on the internet about how to solve this problem but couldn’t find a satisfactory answer. So I have decided to write a detailed article on this error that will help you to remove this error and will save your time.

Proteus Professional 8.13

Proteus Professional 8.13 is the simplest and most advanced software for designing circuits. In which you will have to search for components, place them in the workspace and connect these with wires and your circuit will be ready. you can also design PCB with Proteus 8.13.

If you are looking to by best components for your project I personally suggest you to buy Complete Arduino Kit from here in reasonable price. This will not only save your value able money and time but also give you accurate results.

you may like to read

How to Solve “Fatal simulation error encountered”?

There are different methods to solve this issue, if one is not working then the other will work.

1. Add Libraries:

When you run your simulation a popup window will show displaying

when you click on yes then it will take you to another window displaying these error

• Now what you all have to do is close this window and stop your simulation.
• If you are using any sensors like a gas sensor, water sensor, and flame sensor upload the .hex file in them and again run the simulation.
• The Libraries with .hex Files are easily availablehere. You can download and use them for free.
• After doing this you will notice that simulation failed due to fatal simulator errors has successfully been removed.

if the above-mentioned method is not working, move to the next method.

2. Incorrect .hex file

Another reason for getting real-time simulation failed to start error is the hex file you are uploading is not correct. Uploading the correct file will remove this error.

3. Connections Error

The error occurred due to improper connections like +VCC or GND or any other component or senor. Make sure you have made the right connections.

4. Invalid Value of Component

The simulation error can occur when you have assigned the invalid value to the component that is stopping it from working. For example too large a value of resistor or capacitor etc.

After checking all the above-mentioned steps if you are still getting the error try reinstalling the Proteus because sometimes installation errors can cause this problem.

After reading this article “How To How to Solve “Fatal simulation error encountered? ” you will be able to remove this error. We have tried to cover each aspect of the fatal simulation error and will look for more and try to add those in the next update. Does this work for you? Let us know in the comments section below.

Источник

How to Fix Proteus 8″No Libraries Found!” Error

By inham

As an affiliate, we may earn a commission from qualifying purchases. We get commissions for purchases made through links on this website from Amazon.

Proteus Professional SP3 is an important software in electrical engineering for designing circuits. I have read different articles regarding the problem but didn’t find any satisfactory answer so I have decided to write a precise and accurate solution.

Proteus Professional SP3

Proteus Professional 8.13 is the simplest and most advanced software for designing circuits. In which you will have to search for components and can place them in the workspace and have to connect these with wires.

This software is mostly used for designing and testing circuits. It has different measuring devices like oscilloscope, voltmeter. Ammeter etc. Also using this software you can model microcontrollers, microprocessors, etc

If you are looking to by best components for your project I personally suggest you to buy Complete Arduino Kit from here in reasonable price. This will not only save your value able money and time but also give you accurate results.

Features

• Circuit designing and testing.
• includes all the components for circuit designing
• More than 800 different microcontrollers
• Complete set for designing PCB
• Different Simulations
• Save cost and time for testing circuit

System Requirements

• Operating System: Microsoft® Windows® 2000 with Service Pack 4, or Windows XP with Service Pack 1 or 2
• Memory (RAM): 2 GB of RAM required
• Hard Disk Space: 3 GB of hard disk space for program installation.

No Libraries Found (Proteus Error)

Many of you have faced this problem that after installing Proteus it gives the error “No Libraries Found”. Follow these simple steps to tackle this problem.

• Move to the Lab Center Electronic folder which will be in C Drive and then Program Files.

Step 1

• Now open the LAB Center Electronic, right-click on Proteus 8 Professional, and open properties

Step 2

• Now click on Security, Edit and Add and mark full control then apply and ok

Step 3

• It will take some time for adding files.
• Now one last step, move to the desktop and right-click on Proteus, and click on properties

Step 4

• Now click on Compatibility and mark the changes below

step 5

• Your Proteus Professional 8.10 SP3 is ready to use and your problem has been solved.

After reading this article “How to Fix Proteus 8.10 “No Libraries Found!” Error” you will be able to fix this problem. We have tried to cover each aspect of the library’s error and will look for more and try to add those in the next update. How does this software work for you? Let us know in the comments section below.

Источник

Proteus Simulation error

arschleben

Junior Member level 2

simulation errors in proteus

Hello, recently I build a circuit and load a Hex that is proven to work in a real circuit, but everytime I try to run the simulation in ISIS, I gt this error:

SIMULATION LOG
==============
Design: UNTITLED.DSN
Doc. no.:
Revision:
Author:
Created: 06/03/05
Modified: 06/03/05

Compiling source files.
Build completed OK.
Compiling netlist.
Linking netlist.
Partition analysis.

Simulating partition 1 [D8FDED1F].
Animation started sucessfully.
PROSPICE Release 6.7 SP0 (C) Labcenter Electronics 1993-2005.
SPICE Kernel Version 3f5. (C) Berkeley University ERL.

Reading netlist.
Reading SPICE models.
Loading library ‘ANALOGD.SML’
Loading library ‘APEX.SML’
Loading library ‘BURRBROWN.SML’
Loading library ‘ELANTEC.SML’
Loading library ‘FAIRCHLD.SML’
Loading library ‘INTERSIL.SML’
Loading library ‘LINTEC.SML’
Loading library ‘NATOA.SML’
Loading library ‘SUPERTEX.SML’
Loading library ‘TECCOR.SML’
Loading library ‘TEX101.SML’
Loading library ‘TEX301.SML’
Loading library ‘TEX3_1.SML’
Loading library ‘TEX401.SML’
Loading library ‘TEX5_1.SML’
Loading library ‘VALVES.SML’
Loading library ‘ZETEX.SML’
Building circuit.
Instantiating SPICE models.
[U1] PIC16 model release 6.7 SP0 simulating PIC16877 device.
[U1] Loaded 256 bytes of persistent EEPROM data.
[U1] Loading HEX file ‘ASM ProgsMaurodrum.HEX’.
FATAL: [U1] Program or EEPROM data has invalid address [2000] for this device

Real Time Simulation failed to start

Real Time Simulation FAILED.

Anyone knows what the heck does this mean. what can I do?

Источник

roboforum.ru

Технический форум по робототехнике.

proteus mеga8 и uart

proteus mеga8 и uart

Myp » 27 фев 2007, 21:17

не подскажете господа знатоки как мне усарт меги 8й прикрутить к реальному компорту в протеусе
желательно по пунктам:roll:

ато чёто «непонятно. «(с)

SIMULATION LOG
==============
Design: UNTITLED.DSN
Doc. no.:
Revision:
Author:
Created: 27/02/07
Modified: 27/02/07

Compiling source files.
Build completed OK.
Compiling netlist.
Linking netlist.
Partition analysis.

Simulating partition 1 [9D9532B2].
PROSPICE Release 6.9 SP5 (C) Labcenter Electronics 1993-2006.
SPICE Kernel Version 3f5. (C) Berkeley University ERL.

Reading netlist.
FATAL: Cannot open ‘C:DOCUME

Simulation FAILED due to fatal simulator errors.

а блииин
не заметил

PROTEUS — нужно устанавливать для
пользователя с именем из латинский символов !

чёрт а я немогу пользователя переименовать
придёцца под протеус заводить нового юзера:cry:

хотя нет вот как я сделал:
можно изменить адрес папки temp на корректное
на всякий случай привожу алгоритм:

пуск — панель управления — система — дополнительно — переменные среды
выбрать переменную temp, потом кнопка изменить.

в поле адреса ввести новое расположение временной папки например C:Windowstemp

Myp » 27 фев 2007, 22:00

тоесть если я у всей периферии где надо напишу GND можно не рисовать длинный общий провод?
и он автоматически считается подключённым к земле контроллера и к земле COMPIM .

avr123.nm.ru » 27 фев 2007, 22:06

Myp » 27 фев 2007, 22:30

ладно вроде запустил всё пашеть

такой вопрос
можно одновременно из эмулятора протеуса работать с железным компортом и программой ComPortToolkit или подобной снифферить чё там в железном компорте твориться.

а всётаки как настроить работу с железным компортом?
в порт вставил заглушку, если в терминале сижу то читаю то что сам себе отправляю
а вот симулятор только отправляет и читать отказываеться эхо.

Myp » 27 фев 2007, 23:00

а когда?
ато мне вроде как надо уже а самостоятельно чёт у меня не получается =/
квадратик красный мигает у ножки Tx а в окне терминала ничё нету.
и с клавиатуры ничё не вводицца

ниччё не получаецца
хелп ми энибади
симулирую абсолютно типичный код который сгенерил кодвизард

в мэйне всего 1 строчка putchar(getchar());
тьфу в каком мэйне короче контроллер тупо выполняет вот эту строчку

в протеусе когда ввожу чтонить в окно терминала на compim загораецца красным контакт Tx у compim у ножки контроллера Rx Tx стабильно красный квадратик
ничё не происходит

снифер компорта всё чё ввожу в терминал в симуляторе показывает, но контроллер никак не реагирует
что я делаю не так. как заставить контроллер в протеусе реагировать на то что я ввожу в окно терминала в протеусе
и почему терминал протеуса не показывает то что передаёт контроллер?

ммм отлично там в паузе можно смотреть состояние буфера мк=)
всё чё надо принялось
только блин почемуто ничё не отправляется.

avr123.nm.ru » 28 фев 2007, 12:49

Myp » 28 фев 2007, 13:08

в вмлабе посмотрю щас

ну я там в протеусе моторчики приделал, светики разноцветные,
вопщем сипотяшки всякие, схему электрическую развести собрался.
хотелось сразу всё вместе засимулировать а потом ещё и красиво развести автоматом =)

а ещё оказалось у меня протеус вешает процессор на 100% и притормаживает немножка

хорошо что у меня 2 процессора и можно свободно работать в остальных прогах

пока что пришёл к выводу что если в мк стоит прерывание на прием данных то в протеусе почемуто мк из прерывания катастрофически не вылазит.
непонятно там всё =/

а за такой интерфейс руки отрывать надо. ребята там наверно умные работают но свою хорошую идею реализуют через одно место
этож охренеть закрытое окошко нельзя второй раз открыть во время симуляции иначе как не сделав сброс для всех окошек. я конечно понимаю, мультимониторная хрень и всё такое, но нанять писателя окошек ведь можно.

у меня даже появилась мысль что это какойто неудачный порт под виндоус из какойто военной системы с зачатками UI.
ибо такие контролы сознательный человек в виндоусе понаделать не в состоянии.

Источник

Фрикер Клуб

Изучение уязвимостей электронных систем

Proteus 8

Proteus 8

Сообщение maxi » 10 июн 2022, 15:00

Парни,не так давно начал работать с ATMega8 и наткнулся на такую проблему. Программа выдает ошибку или закрывается
ошибка вот такая :
fatal error internal exception : access violation in module unknown 0f2e4447

Если не добавлять сам проц,то программа работает нормально.
В чем может быть проблема ?

Re: Proteus 8

Сообщение DIVER_SANT » 23 июн 2022, 18:38

maxi писал(а): ↑ 10 июн 2022, 15:00 Парни,не так давно начал работать с ATMega8 и наткнулся на такую проблему. Программа выдает ошибку или закрывается
ошибка вот такая :
fatal error internal exception : access violation in module unknown 0f2e4447

Если не добавлять сам проц,то программа работает нормально.
В чем может быть проблема ?

В пути к библиотеке содержится кириллические символы.

Источник

© 2023 APG vNext Commercial Version 4.5

View previous topic :: View next topic
Author	Message
PROMOD Joined: 01 Feb 2018 Posts: 42	Fatal simulation error! Posted: Thu Feb 01, 2018 7:25 am     After writing a program and building hex file when I attempt to test it in Proteus and run the following error shows- «Fatal simulation error» Could someone please explain the problem? I am using Demo of CCS 8.6
temtronic Joined: 01 Jul 2010 Posts: 8709 Location: Greensville,Ontario	Posted: Thu Feb 01, 2018 7:39 am     read Sticky PIC101 get rid of Proteus( ISIS ) Proteus is a damaged program, it’s busted, corrupted, flawed.. IT DON’T WORK
Ttelmah Joined: 11 Mar 2010 Posts: 18389	Posted: Thu Feb 01, 2018 7:44 am     Also since the latest version of CCS, is 5.076, I wonder what environment you really are using…
PROMOD Joined: 01 Feb 2018 Posts: 42	Posted: Thu Feb 01, 2018 11:20 am     temtronic wrote: read Sticky PIC101 get rid of Proteus( ISIS ) Proteus is a damaged program, it’s busted, corrupted, flawed.. IT DON’T WORK Then what software can I use to check my coding that is done in CCS compiler?
Ttelmah Joined: 11 Mar 2010 Posts: 18389	Posted: Thu Feb 01, 2018 12:09 pm     A PIC.
temtronic Joined: 01 Jul 2010 Posts: 8709 Location: Greensville,Ontario	Posted: Thu Feb 01, 2018 1:24 pm     The key problem with ‘simulators’ is that unless you spend 10s of thousands of dollars on one, NONE will truly simulate the real WORLD. Countless postings here on ‘it works in Proteus, but NOT in the PIC’. It’s in the ‘little details’ like Proteus NOT caring that you haven’t got an xtal, or the wrong caps or even the wrong or missing VDD ! For less than $100 you can buy PICs, parts, breadboards, programmer and maybe an oscilloscope. These days you can cut code, compile, burn and test in less than 15 minutes. That’s how long it took to erase the first PICs, 20+ years ago ! When I consider my first ‘personal computer’ cost me just over $10,000, $100 to get into PICs is well, a dream !!! Jay
PCM programmer Joined: 06 Sep 2003 Posts: 21687	Posted: Thu Feb 01, 2018 1:26 pm     temtronic, I suspect a lot of these people come from countries where they don’t have $100. Or at least, they don’t have it to spend on PICs.
Ttelmah Joined: 11 Mar 2010 Posts: 18389	Posted: Thu Feb 01, 2018 2:41 pm     Of course if the Proteus was legitimate this would rather obviate this argument, but presumably it (and probably CCS as well), have come from other sources….
temtronic Joined: 01 Jul 2010 Posts: 8709 Location: Greensville,Ontario	Posted: Thu Feb 01, 2018 6:27 pm     I just checked the Proteus website…curious..as there’s been a lot of action recently here. A PIC Bundle to do 12, 16 and 18 series is $1000 ! AND there’s a LOT of ‘limitations’ ( it doesn’t simulate a full PIC). Even a single series pkg is $500. And the trio (3 PICs) version is $250. It seems to me a serious hobbiest should invest in real PICs and parts, far cheaper than the ‘fantasy world’ of a poorly written simulator. Jay
Ttelmah Joined: 11 Mar 2010 Posts: 18389	Posted: Fri Feb 02, 2018 2:42 am     One thing that will give »Fatal simulation error’ in Proteus is the simple one of the chip family not being licensed…..
Display posts from previous:

Powered by phpBB © 2001, 2005 phpBB Group