Hp error 0605

Error b0605 hp 2055

КОНФЕРЕНЦИЯ СТАРТКОПИ
Принтеры, копировальные аппараты, МФУ, факсы и другая офисная техника:
вопросы ремонта, обслуживания, заправки, выбора

На весь ресурс всего пара тем об этой ошибке. И никакого внятного ответа. Кто нибудь сталкивался так, что бы решить эту проблему? Новый форматер — это конечно хорошо. Но как то это не серьезно.

DOMKRAT (0): как то это не серьезно
?? Желаете его поремонтить??))

Угумс, а вы мне бразер припоминаете ?)))

Нет, уточняю ваши намерения и интересуюсь конкретными планами)

(0) А можно фото ошибки с дисплея . желательно на английском.

Все. Готов он. Прошил я его. Хоть это и муторно и не с первого раза я все понял (все ж по англицки, по русски нема подсказок) — но как на официалах написано — так и есть. Треба шить — значт надо шить. А вот греть форматер как оказалось не надо вовсе, как это в одной из двух темок советовалось.

Ну-ну. Греть вас никто, конечно, не заставляет. Но если вы с этой ошибкой ни разу до этого не разбирались, а теперь прошили, и, обрадовавшись и взямши за это денежку, отдадите его, то будьте готовы к повторному приносу тела недовольным клиентом, и там уже прошивка вам вряд ли чем поможет, а клиенту придётся объяснять, за что вы прошлый раз взяли деньги и почему теперь надо гораздо больше денег, чтоб оживить трупа. Потому что изначальная проблема на 90% совсем не в прошивке. На вашем месте я бы предупредил клиента, что склероз, скорее всего, будет прогрессировать и взял бы за ремонт чисто символически.

serry (6): будьте готовы к повторному приносу тела недовольным клиентом
Это-то стопудово. Весь вопрос — когда (после какого пробега). Ставлю месяца на три максимум. Если дадите гарантию на этот или больший срок — секас будет повторным))

Scuzzy (7): секас будет повторным — не просто повторным, а более жёстким, так сказать.

Источник

Error b0605 hp 2055

‎06-09-2011 07:13 PM

• Mark as New
• Bookmark
• Subscribe
• Permalink
• Print
• Flag Post

My HP Laserjet 2055DN displays a firmware error message: B0605

The printer and computer are connected via a USB cable and are «seeing» each other, when the printer is switched off the computer recognizes this and makes the «device unplugged» sound.

I have downloaded the 2050 firmware update and put the printer in Bootcode mode

When I then run the «send firmware» the software seems to complete and the smiley graphic comes up but nothing happens. The printer does not acknowledge the update or change messages.

The error code continues to remain current so I cannot use the printer.

As this is my main business printer this is quite inconvenient.

Does anyone know how to fix this?

Yours sincerely
John Edmiston

‎05-24-2012 07:34 AM — edited ‎05-24-2012 07:37 AM

• Mark as New
• Bookmark
• Subscribe
• Permalink
• Print
• Flag Post

I know this is an old post, but because it ranks so high in google and I feel I have a solution, I thought I would answer it.

I had a users with an HP P2055DN who’s printer displayed the error B0605 message. I followed HP’s directions at http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?objectID=c01687323&lang=en&cc=us&conte.

and put the printer in BootCode mode then ran the firmware updater.

The directions indicated that the printer would restart on it’s own, but it did not do that for me (and I feel many other people on the Internet according to what I could pull up on Google).

What I did was let the printer sit for about a minute after the Firmware Updater said it was done, then powered down the printer and pulled out it’s power cord. I let it sit for about 15 seconds, then plugged it back in and started it up. When the printer started up, the printer’s display went through a bunch of messages (Erasing. ) for a few seconds. When it got done with all of the messages, I was able to print to the printer again.

Источник

Error b0605 hp 2055

‎12-05-2013 06:52 AM

• Mark as New
• Bookmark
• Subscribe
• Permalink
• Print
• Flag Post

hp laserjet 2055dn Error B0605, i need solutions for this error i tried with site but it not working.

‎12-05-2013 11:11 AM

• Mark as New
• Bookmark
• Subscribe
• Permalink
• Print
• Flag Post

Please refer to this document to help resolve you issue on the error message with this printer.

I am an HP employee.

Say Thanks by clicking the Kudos Star in the post that helped you.
Please mark the post that solves your problem as Accepted Solution

‎12-05-2013 11:11 AM

• Mark as New
• Bookmark
• Subscribe
• Permalink
• Print
• Flag Post

Please refer to this document to help resolve you issue on the error message with this printer.

I am an HP employee.

Say Thanks by clicking the Kudos Star in the post that helped you.
Please mark the post that solves your problem as Accepted Solution

‎12-06-2013 10:49 PM

• Mark as New
• Bookmark
• Subscribe
• Permalink
• Print
• Flag Post

whatever u told us we did that but still it is not working,

when i strat the printer it immediately give b6050 error cade, n it is not at all communicating with the pc, please provide us solution this.

‎12-06-2013 10:55 PM

• Mark as New
• Bookmark
• Subscribe
• Permalink
• Print
• Flag Post

‎12-07-2013 02:36 PM

• Mark as New
• Bookmark
• Subscribe
• Permalink
• Print
• Flag Post

What were you trying to do when this error code happened? Installing a FW upgrade? If so, did you get the FW smiling face and a success! to tell you that you had completed the upgrade successfully?

If you have already sent the FW upgrade to the printer, try powering down the printer, pulling the power cord and letting it sit for about 15 secs. Plug everything back in and start the printer up. What happens? Do you see a new FW initialization (erasing) messaging? If so, let the printer do its job.

If not, try re-sending the printer FW upgrade again using the FW updater — once you have the complete update success message. What happens? Do you have the error message or did the printer initialize (erase), ect.) If not, power down, pull power cord, let sit. Plug everything back in and start up.

I am an HP employee.

Say Thanks by clicking the Kudos Star in the post that helped you.
Please mark the post that solves your problem as Accepted Solution

Источник

HP Printer Error B0605

B0605 Error Code HP Printer

You may see hp printer error b0605 error message popping up if the firmware of your printer gets crashed. Firmware gets crashed due to inappropriate behaviour, like: turning off the printer while the vital firmware update one is going on. This issue could be resolved by following the troubleshooting steps, like get the firmware re-flash in the BootCode mode and after that try rebooting your printer. Though firmware re-flash won’t help always, but yes, it is one of the best major you can take as a first step. If the HP Printer Error Message is displayed then your printer won’t be booted up in the ready state.

Causes B0605 Error Message HP Printer

Causes:

There might be two causes due to which this error is received:

• You have installed the software driver of P2050 series printer on the PC previously
• Software driver of P2050 series printer is not installed previously on the computer

Instruction

Case 1: Installation of driver was done previously on PC

1. Ensure that printer is places in the bootcode mode

• Keep holding the OK and Cancel buttons
• Keep the power of the printer ON
• Make sure that you are holding the buttons till the time Hewlett-Packard in first line and the Bootcode in second line is not displayed by the control panel

1. Check carefully that your printer is connected to the PC through USB. After that run the firmware HP LJ P2055
2. Now go to the dropdown list and after that click on the button of Send Firmware

Observe the panel of printer control carefully and make sure that on the control panel Downloading Update Data is flashing up along with the Programming App Flash. Wait, till the time upgrade utility gets finished. Your printer will be automatically restarted, and you will be able to see, Ready, displayed on control panel.

This means your firmware is recovered successfully.

Case 2: Installation of driver is not done previously

1. Install the driver

• Then get the printer installation CD inserted to it
• After that go to the Start first and then to Settings and then to Printers and Faxes in Windows Operating System
• In order to get the Add Printer Wizard started click on the Add a Printer, and then click on the Next button
• Then check the local printer that is attached with the computer system. After that make sure that you remove the checkmark from Install my Plug and Play printer and Automatically detect box and then hit the Next button
• Then go to the port of Use the following and select the FILE and tap on the Next button
• After that, click on the button of Have Disk
• Go to the CD Drive and browse it, where the printer installation CD was previously inserted. Click on the OK button
• Click on the next button by highlighting the HP Laser Jet present in installation CD of printer. After that tap the Next button
• By specifying the name of the Printer, hit the Next button
• When, DO you want to print a test page? pop up, click on NO and then tap on Next
• Click on the button saying Finish, and let the driver install
• You will see that Verify printer is present in the window of Printer and Faxes

1. Placing the P2055 in the bootcode mode

• Keep holding the OK and Cancel buttons
• Turn on the power of the printer
• Keep on holding the buttons, until you see the display of the control panel flashing Hewlett-Packard in top line and Bootcode displaying on second line. Your printer is now in the mode of bootcode

1. Go to the window of Printer and Faxes and on the icon of the HP LaserJet P2050 Series PCL6, do right click and choose the Properties
2. Then by clicking on the tab of Ports you can see USB ports
3. After that get the Property window closed
4. Then ensure that USB cable is plugin from PC
5. You will see the Found New Hardware Wizard popping up and enumeration of USB will start taking place
6. Then open the Printer Properties again and choose the tab of Ports again
7. Then tick mark the correct port in ports tab
8. Click on Cancel if the window of Found New Hardware Wizard pop ups.
9. Run the Firmware Update Utility
10. Now from the drop down choose the printer and then tap on the button of Send Firmware
11. Keep a close eye on the control panel and make sure that control panel is flashing the Downloading Update Data along with the Programming App Flash. Wait till the time upgrade utility gets finished. Automatically the printer will be restarted and you will be able to see, Ready, flashing on the display of control panel. The firmware is recovered successfully
12. Close the New Found Hardware Wizard

Troubleshooting Steps HP Printer Error B0605

Troubleshooting the Printer Error B0605:

Step 1: Get the Firewall upgraded of the Printer

• First of all, get the correct firmware downloaded
• Then reload the upgraded and basic firmware
• Pull the power cord and turn off the power of the printer and let it remain same for few seconds
• Plug in back and get the printer started up
• Check whether the error is removed or not. In case it is not, then try the next step

Step 2: Reinstalling the toner by removing it first

• Disconnect and turnoff the printer’s power source
• After that remove the toner mesh and paper tray as well
• Turn on the power of the unit for at least 50 to 60 seconds and then turn the power off again
• Get the paper tray and toner mesh installed again
• Turn on the power of the unit and make sure that the power is up of the unit before getting the test page printed

Step 3: Reflashing firmware

• Enter the boot mode and make sure that firmware is reflashed, also reboot the printer
• This reflashing will help you to get rid of the error

Scope of Services

• Advanced Printer Tech Support through experienced professionals
• Immediate resolution of all the technical issues
• Tech savvy and self-motivated staff
• Capable of providing the customized solutions Dial Now

Источник

Модератор: vetal

Вернуться в Принтеры, МФУ, факсы, копиры формата A4

Кто сейчас на форуме

Сейчас этот форум просматривают: нет зарегистрированных пользователей и гости: 53

Перейти к контенту