Key short error

If the oven fails to operate, you may see an information code on the display. Check the table below and try the suggestions. Built-In Electric Wall Oven - Digital Display Single Wall Oven: Error CodeSolution C-d0This code occurs if the control key is short for 1 minute. Clean the buttons and make sure there is

If the oven fails to operate, you may see an information code on the display. Check the table below and try the suggestions.

Built-In Electric Wall Oven – Digital Display Single Wall Oven:

Error Code Solution
C-d0 This code occurs if the control key is short for 1 minute. Clean the buttons and make sure there is no water on/around them. Turn off the oven and try again. If the problem continues, contact a local Samsung service center
C-d1 This code occurs if the door lock is mispositioned. Touch OVEN OFF, and then restart the oven. If the problem persists, disconnect all power to the oven for at least 30 seconds and then reconnect the power.
C-F0 This code occurs if communication between the Main and Sub PBA is interrupted. Touch OVEN OFF, and then restart the oven. If the problem persists, disconnect all power to the oven for at least 30 seconds and then reconnect the power.
C-F2 This code occurs if communication between the Main and Touch is interrupted. Touch OVEN OFF, and then restart the oven. If the problem persists, disconnect all power to the oven for at least 30 seconds and then reconnect the power.
C-10 The cooking sensor is open when the microwave is operating. The cooking sensor is short when the microwave is operating. Touch OVEN OFF, and then restart the oven. If the problem persists, disconnect all power to the oven for at least 30 seconds and then reconnect the power.
C-20 The oven sensor is open when the oven is operating. The oven sensor is short when the oven is operating. Touch OVEN OFF, and then restart the oven. If the problem persists, disconnect all power to the oven for at least 30 seconds and then reconnect the power.
C-21 This code occurs if the internal temperature rises abnormally high. Touch OVEN OFF, and then restart the oven. If the problem persists, disconnect all power to the oven for at least 30 seconds and then reconnect the power.
C-23 The temp probe sensor is short when the oven is operating. Press OFF, and then restart the oven. If the problem persists, disconnect all power to the oven for at least 30 seconds and then reconnect the power
C-30 The PCB sensor is open when the oven is operating. The PCB sensor is short when the oven is operating. Touch OVEN OFF, and then restart the oven. If the problem persists, disconnect all power to the oven for at least 30 seconds and then reconnect the power.
C-31 This code occurs if the PCB temperature rises abnormally high.
C-70 The steam sensor is open when the oven is operating. The steam sensor is short when the oven is operating. Press OFF, and then restart the oven. If the problem presists, disconnect all power to the oven for at least 30 seconds and then reconnect the power.
C-72 There are drain system-related problems.Press OFF, and then restart the oven. If the problem presists, disconnect all power to the oven for at least 30 seconds and then reconnect the power.
C-A2 The cooling motor is operating abnormally.
dC This code appears if the divider is inserted or removed while the oven is operating. Make sure the divider is inserted properly, and then restart the oven. If the problem persists, disconnect all power to the oven for at least 30 seconds and then reconnect the power.
bAd LinE This code occurs if the power connection is plugged in improperly. Reconnect the power connection properly, and the message disappears.
E-01 Open Error
E-02 Cooking Time Setting Over Error (Microwave)
E-03 Cooking Time Setting Over Error (Grill)
E-04 Cooking Time Setting Over Error (Convection)
E-05 Cooking Time Setting Over Error (Combination)
E-06 Swing Heater Error
E-11 Open Gas Sensor Error
E-12 Short Gas Sensor Error
E-13 T1 Max Time Gas Sensor Error
E-14 Dry Up / No Load Gas Sensor Error
E-21 Open Temp Sensor Error
E-22 Short Temp Sensor Error
E-23 T1 Max Time Error
E-24 Over Temperature Error
E-25 Micro Cook Abnormal Temperature Error
E-26 Temperature Not Over AD Error
E-31 Open Gas Sensor Error
E-32 Short Gas Sensor Error
E-33 Under Weight Error
E-34 Over Weight Error
E-35 Invalid Weight Error
E-36 Door Open Error
E-41 Open Easy/PH Sensor Error
E-42 Short Easy/PH Sensor Error
E-43 T1 Max Time Easy/PH Sensor Error
E-44 Dry Up Easy/PH Sensor Error
E-45 Cooling Error
E-46 Primary Open Error
E-47 Door Open Error
E-51 Sense Failure
E-52 EEPROM Short Error
E-53 Read/Write Error
E-54 Zero Error
E-61 Open Humidity Sensor Error
E-62 Short Humidity Sensor Error
E-63 T1 Max Time Humidity Sensor Error
E-71 Steam Sensor Open Error
E-72 Steam Sensor Short Error
E-81 Communication Open Error
E-82 Communication Short Error
E-83 Communication Error
E-X1 Additional Open Error
E-X2 Additional Short Error
SE Key Short Error
TE Touch Communication Error
Hot Make sure the panel isn’t hot. If the oven is currently too hot for the electronics in the panel to operate, it will display Hot when you try to perform a function. When the oven is a little cooler, this may only happen when certain buttons are touched (like Self Clean) because the oven is still too hot to perform that particular function. The interior lamp will also not function during extreme heat conditions such as a Self Clean cycle, so its button may appear to do nothing in that situation as well.
Loc Make sure the panel isn’t locked. The appearance of Control Lock varies between models, but it will usually be displayed as a padlock icon or as the code Loc, or both. Instructions for turning off Control Lock are written on the panel.

Samsung Oven Parts

Samsung Oven Parts

Samsung works hard to ensure that you don’t have problems with your new electric oven. If you run into unexpected trouble, look first for a solution in the tables below.

Trouble Possible Cause
The display goes blank. A fuse in your home may be blown or the circuit breaker tripped. Replace the fuse or reset the circuit breaker.
The buttons cannot be pressed properly. There is foreign matter caught between the buttons. Remove the foreign matter and try again.
The oven will not turn on. The oven is not completely plugged into the electrical outlet. Make sure the electrical plug is inserted into a live, properly grounded outlet.
The oven light will not turn on. he light is loose or defective. Tighten or replace the lamp.
The oven smokes excessively during broiling. The oven controls have not been set properly. The meat has been placed too close to the element. The meat has not been properly prepared. Grease has built up on oven surfaces.
Food does not bake or roast properly. The oven controls have not been set correctly. The oven rack has been positioned incorrectly or is not level. Incorrect cookware or cookware of improper size is being used. The oven thermistor needs to be adjusted.
Food does not broil properly. The serving size may not be appropriate. The rack has not been properly positioned. The cookware is not suited for broiling. In some areas, the power (voltage) may be low.
The oven temperature is too hot or too cold. The oven sensor needs to be adjusted.
The oven will not self-clean. The oven temperature is too high to start a self-clean operation. Allow the oven to cool and then reset the controls.
Excessive smoking during a self-cleaning cycle. There is excessive soiling in the oven. Touch OVEN OFF. Open the windows to rid the room of smoke. Wait until the selfcleaning cycle is cancelled. Wipe up the excessive soil and then start the selfcleaning cycle again.
The oven door will not open after a selfcleaning cycle. The oven is too hot. Allow the oven to cool.
The oven is not clean after a self-cleaning cycle. The oven controls were not set correctly. The oven was heavily soiled.
Steam is coming out of the vent. As the number of racks or amount of food being cooked increases, the amount of visible steam will increase. This is normal operation and not a system failure. Use the oven as usual.
A burning or oily odor is coming from the vent. This is normal for a new oven and will disappear in time.
Strong odor. An odor coming from the insulation around the inside of the oven is normal for the first few times the oven is used. Operate the oven empty on the bake setting at 400 °F for 1 hour.
The oven racks are difficult to slide. The shiny, silver-colored racks were cleaned in a selfcleaning cycle. Apply a small amount of vegetable oil to a paper towel, and then wipe the edges of the oven racks with the paper towel.
The oven door is locked. The circuit breaker has been tripped or there was a power failure while the oven door was locked. Activate Control Lockout, and then unlock the control.

Samsung Oven Control Panel

Samsung Oven Control Panel

How to set the oven for steam-cleaning?

For light cleaning, the Steam-cleaning function saves time and energy. For heavier duty cleaning, use the self-cleaning function.

How to set the oven for steam-cleaning

How to set the oven for steam-cleaning?
  1. Remove all accessories from the oven.
  2. Pour approximately 10 oz. (300 ml) of water onto the bottom of the empty oven and close the oven door. Use tap water only, not distilled water.
  3. Press Steam Clean.
  4. Press START/SET. When the operation is complete, the display will blink and a beep will sound.
  5. Press OVEN OFF.
  6. Clean the oven’s interior. There will be a significant amount of water remaining on the bottom of the oven after a steam-cleaning cycle. Remove the residual water with a sponge or soft dry cloth.

When steam-cleaning, use exactly 10 oz. of water since this produces the best results.

If you press Steam Clean when the oven temperature is above 100˚F, Hot will appear in the display. Because these functions produce the best results when started while the oven is cool, we recommend that you wait until the oven has cooled down and Hot disappears from the display.

Samsung Oven User Manual PDF

Источник

Hi all,

I am trying to insert a record into the ADRC table through FM ADDR_SAVE_INTERN. First, I am pulling the next available ADRNR number through GET_NEXT_ADRNR. That is working fine and pulling back the next available number. However, when I insert via ADDR_SAVE_INTERN (adrc_i) I am getting a short dump with error DBSQL_DUPLICATE_KEY_ERROR. I have checked the ADRC table and the ADRNR number I am passing does not exist so I dont know why it is complaining about a duplicate?

Below is full error:

Category ABAP programming error

Runtime Errors DBSQL_DUPLICATE_KEY_ERROR

Except. CX_SY_OPEN_SQL_DB

ABAP Program SAPLSZA0

Application Component BC-SRV-ADR

Short Text Open SQL array insert produces duplicate records in the database. What happened? Error in the ABAP application program. The current ABAP program «SAPLSZA0» had to be terminated because it found a statement that could not be executed.

What can I do? Note which actions and entries caused the error to occur. Consult your SAP administrator. Using transaction ST22 for ABAP dump analysis, you can view, manage, and retain termination messages for longer periods. Using Transaction ST22 for ABAP Dump Analysis, you can look at and manage termination messages, and you can also keep them for a long time. Error analysis An exception has occurred which is explained in more detail below. The exception is assigned to class ‘CX_SY_OPEN_SQL_DB’ and was not caught in procedure «ADDR_SAVE_INTERN» «(FUNCTION)», nor was it propagated by a RAISING clause. Since the caller of the procedure could not have anticipated this exception, the current program was terminated. The reason for the exception is: When an Open SQL array insert is performed, trying to insert a record into the database table «ADRC_UUID_INDEX» causes the function to terminate if a record with the same key already exists. (When an Open SQL individual record insert is performed, this situation does not cause the function to terminate. SY-SUBRC is set to 4 instead.)

Источник

#1

alecs

    Участник форума

  • Пользователи

  • 15 сообщений
  • Пол:Мужчина
  • Город:с Петербург

Отправлено 04 июля 2010 — 09:01

помогите пожалуйста.При нажатии на старт на дисплее появляется SHORT ERROR на любом типе аккумуляторов.Или как любая китайская техника
расчитана на два года? И надо новую зарядку покупать? Спасибо.

  • Наверх

#2

kartman

kartman

    Активный участник форума

  • Пользователи

  • 159 сообщений
  • Пол:Мужчина
  • Город:лен область

Отправлено 04 июля 2010 — 21:15

помогите пожалуйста.При нажатии на старт на дисплее появляется SHORT ERROR на любом типе аккумуляторов.Или как любая китайская техника
расчитана на два года? И надо новую зарядку покупать? Спасибо.

имею в пользовании аналогичное устройство. иногда у него возникает глюк типа не вижу аккумулятор. зрение прибора восстанавливается после нескольких энергичных (по возрастающей) ударов данным прибором об стол. если стол жалко то можно и об пол. видимо без физического насилия (воздействия) эти штуки работать не хотят.

  • Наверх

#3

Mursik

Mursik

    Завсегдатай

  • Пользователи

  • 702 сообщений
  • Пол:Мужчина
  • Город:Санкт-Петербург

Отправлено 05 июля 2010 — 00:10

помогите пожалуйста.При нажатии на старт на дисплее появляется SHORT ERROR на любом типе аккумуляторов.Или как любая китайская техника расчитана на два года? И надо новую зарядку покупать?

Наверное, разряжали ЛиПо перед этим? Хорошим током? Очень похоже на сгоревший разрядный транзистор. Если батарею вообще не подключать, «заряд» идёт?

Сообщение отредактировал Mursik: 05 июля 2010 — 00:16

  • Наверх

Источник

Понравилась статья? Поделить с друзьями:
  • Key error питон
  • Key error try again 162
  • Key error python json
  • Key error not in index pandas
  • Kess v2 ошибка wake up error