Код ошибки 4600 kyocera 8525

Код ошибки Описание ошибки Причина ошибки 0030 FAX control PWB system error
Processing with the fax software was disabled due to a hardware problem. Defective FAX control PWB. 0060 Engine PWB type error Defective engine sub PCB. 0070 FAX control PWB incompatible detection error
Abnormal detection of FAX control PWB incompatibility In the initial communication with the FAX control PWB, any normal communication command is not transmitted. Defective FAX software
Defective FAX control PWB. 0100 Backup memory device error Defective flash memory. 0120 MAC address data error
For data in which the MAC address is invalid. Defective main PWB.
Defective flash memory.
Defective engine PWB. 0130 Backup memory read/write error (main PWB) Defective flash memory.
Defective main PWB. 0140 Backup memory data error (main PWB) Defective flash memory.
Defective main PWB. 0150 Backup memory read/write error (engine PWB)
Detecting engine PWB EEPROM communication error. Improper installation engine PWB EEPROM.
Defective engine PWB.
Device damage of EEPROM. 0160 Backup memory data error (engine PWB) Defective flash memory.
Defective engine PWB. 0170 Billing counting error
A checksum error is detected in the main and engine backup memories for the billing counters. Data damage of EEPROM.
Defective PWB. 0180 Machine number mismatch
Machine number of main and engine does not match. Data damage of EEPROM. 0320 I/O CPU communication error
A communication error is detected 10 times in succession. Defective PWB. 0630 DMA error DMA transmission of image data does not complete within the specified period of time. Poor contact in the connector terminals. Defective main PWB. 0800 Image processing error
JAM05 is detected twice. Defective main PWB. 0830 FAX control PWB flash program area checksum error
A checksum error occurred with the program of the FAX control PWB. Defective FAX software.
Defective FAX control PWB. 0840 Faults of RTC
The time is judged to go back based on the comparison of the RTC time and the current time or five years or more have passed. The battery is disconnected from the main PWB.
Defective main PWB. 0870 FAX control PWB to main PWB high capacity data transfer error
High-capacity data transfer between the FAX control PWB and the main PWB of the machine was not normally performed even if the data transfer was retried the specified times. Improper installation FAX control PWB.
Defective FAX control PWB or main PWB. 0920 Fax file system error
The backup data is not retained for file system abnormality of flash memory of the FAX control PWB. Defective FAX control PWB. 1010 Lift motor error
After cassette 1 is inserted, lift sensor does not turn on within 12 s. This error is detected four times successively. Defective bottom plate elevation mechanism in the cassette.
Defective connector cable or poor contact in the connector.
Defective drive transmission system of the lift motor.
Defective lift motor.
Defective engine PWB. 1020 PF lift motor error (paper feeder)
After cassette 2 is inserted, PF lift sensor 1 does not turn on within 12 s. This error is detected four times successively. Defective bottom plate elevation mechanism in the cassette.
Defective connector cable or poor contact in the connector.
Defective drive transmission system of the PF lift motor 1.
Defective PF lift motor 1.
Defective PF main PWB. 1030 PF lift motor error (paper feeder)
After cassette 3 is inserted, PF lift sensor 2 does not turn on within 12 s. This error is detected four times successively. Defective bottom plate elevation mechanism in the cassette.
Defective connector cable or poor contact in the connector.
Defective drive transmission system of the PF lift motor 2.
Defective PF lift motor 2.
Defective PF main PWB. 1800 Paper feeder communication error
A communication error is detected 10 times in succession. Improper installation paper feeder.
Defective connector cable or poor contact in the connector.
Defective engine PWB.
Defective PF main PWB. 1900 Paper feeder EEPROM error
When writing the data, the write data and the read data is not continuously in agreement 5 times. Defective PF main PWB.
Device damage of EEPROM. 2000 Main motor steady-state error
Stable OFF is detected for 1 s continuously after main motor stabilized. Defective connector cable or poor contact in the connector.
Defective drive transmission system of the main motor.
Defective main motor.
Defective engine PWB. 2010 Main motor drive error
The main motor is not stabilized within 2 s after driving starts. Defective connector cable or poor contact in the connector.
Defective drive transmission system of the main motor.
Defective main motor.
Defective engine PWB. 2101 Developer motor K steady-state error
The rated speed signal detected the stability OFF continuously for 1 s after the developer motor K stabilizes. Defective connector cable or poor contact in the connector.
Defective drive transmission system.
Defective motor.
Defective PWB. 2102 Developer motor YCM steady-state error
The rated speed signal detected the stability OFF continuously for 1 s after the developer motor YCM stabilizes. Defective connector cable or poor contact in the connector.
Defective drive transmission system.
Defective motor.
Defective PWB. 2111 Developer motor K startup error
Developer motor K is not stabilized within 2 s since the motor is activated. Defective connector cable or poor contact in the connector
Defective drive transmission system.
Defective motor.
Defective PWB. 2112 Developer motor YCM startup error
Developer motor YCM is not stabilized within 2 s since the motor is activated. Defective connector cable or poor contact in the connector
Defective drive transmission system.
Defective motor.
Defective PWB. 2300 Fuser motor steady-state error
The rated speed signal detected the stability OFF continuously for 1 s after the fuser motor stabilizes. Defective connector cable or poor contact in the connector.
Defective drive transmission system.
Defective motor.
Defective PWB. 2310 Fuser motor startup error
Fuser motor is not stabilized within 2 s since the motor is activated. Defective connector cable or poor contact in the connector.
Defective drive transmission system.
Defective motor.
Defective PWB. 2550 Conveying motor steady-state error
The rated speed signal detected the stability OFF continuously for 1 s after the conveying motor stabilizes. Defective connector cable or poor contact in the connector.
Defective drive transmission system.
Defective motor.
Defective PWB. 2560 Conveying motor startup error
Conveying motor is not stabilized within 2 s since the motor is activated. Defective connector cable or poor contact in the connector.
Defective drive transmission system.
Defective motor.
Defective PWB. 2600 PF drive motor error (paper feeder)
When the PF drive motor is driven, error signal is detected continuously for 1 s. Defective connector cable or poor contact in the connector.
Defective drive transmission system of the PF drive motor.
Defective PF drive motor.
Defective PF main PWB. 2700 TC belt motor error
When the TC belt motor is driven, error signal is detected continuously for 1 s. Defective connector cable or poor contact in the connector.
Defective drive transmission system of the PF drive motor.
Defective PF drive motor.
Defective PF main PWB. 3100 ISU home position error
The home position is not correct when the power is turned on or at the start of copying using the table. Defective connector cable or poor contact in the connector.
Defective home position sensor.
Defective ISU motor.
Defective CCD PWB.
Defective engine PWB. 3200 Exposure lamp error
When input value at the time of exposure lamp illumination does not exceed the threshold value between 5 s. Defective connector cable or poor contact in the connector.
Defective exposure lamp.
Defective CCD PWB.
Defective main PWB. 3500 Communication error between scanner and ASIC
An error code is detected 3 times in succession. Defective connector cable or poor contact in the connector.
Defective CCD PWB.
Defective main PWB. 3600 Scanner sequence error Defective main PWB or engine PWB. 4000 Polygon motor synchronization error
The polygon motor is not stabilized within 10 s after driving starts. Defective connector cable or poor contact in the connector.
Defective polygon motor.
Defective engine PWB. 4001 Polygon motor (K) steady-state error
The rated speed signal detected the stability OFF continuously for 1 s after the polygon motor (K) stabilizes. Defective connector cable or poor contact in the connector.
Defective motor
Defective PWB. 4002 Polygon motor (С) steady-state error
The rated speed signal detected the stability OFF continuously for 1 s after the polygon motor (С) stabilizes. Defective connector cable or poor contact in the connector.
Defective motor
Defective PWB. 4003 Polygon motor (M) steady-state error
The rated speed signal detected the stability OFF continuously for 1 s after the polygon motor (M) stabilizes. Defective connector cable or poor contact in the connector.
Defective motor
Defective PWB. 4004 Polygon motor (Y) steady-state error
The rated speed signal detected the stability OFF continuously for 1 s after the polygon motor (Y) stabilizes. Defective connector cable or poor contact in the connector.
Defective motor
Defective PWB. 4010 Polygon motor steady-state error
Stable OFF is detected for 1 s continuously after polygon motor stabilized. Defective connector cable or poor contact in the connector.
Defective polygon motor.
Defective engine PWB. 4011 Polygon motor (K) startup error
Polygon motor (K) is not stabilized within 10 s since the motor is activated. Defective connector cable or poor contact in the connector.
Defective motor.
Defective PWB. 4012 Polygon motor (C) startup error
Polygon motor (C) is not stabilized within 10 s since the motor is activated. Defective connector cable or poor contact in the connector.
Defective motor.
Defective PWB. 4013 Polygon motor (M) startup error
Polygon motor (M) is not stabilized within 10 s since the motor is activated. Defective connector cable or poor contact in the connector.
Defective motor.
Defective PWB. 4014 Polygon motor (Y) startup error
Polygon motor (Y) is not stabilized within 10 s since the motor is activated. Defective connector cable or poor contact in the connector.
Defective motor.
Defective PWB. 4100 BD initialization error
BD is not detected within 1 s after polygon motor stabilized. Defective connector cable or poor contact in the connector.
Defective APC PWB.
Defective BD PWB.
Defective main PWB. 4600 LSU cleaning motor error
When the LSU cleaning motor is driven, an error signal is detected continuously for 1 s. Defective connector cable or poor contact in the connector.
Defective drive transmission system.
Defective motor. Defective PWB. 4700 VIDEO ASIC device error Defective connector cable or poor contact in the connector.
Defective main PWB or engine PWB. 4950 LSU CPU communication error
A communication error is detected 10 times in succession. Defective connector cable or poor contact in the connector.
Defective PWB. 6000 Broken fuser heater wire
The detected temperature of fuser thermistor does not reach the specified temperature (ready indication temperature) after the fuser heater has been turned on continuously for 60 s in warming up. The fusing temperature at 7 seconds and 20 seconds since fuser temperature control has occurred differs by 43°C/109.4°F or less. Defective connector cable or poor contact in the connector.
Deformed connector pin.
Defective triac.
Fuser thermostat triggered.
Broken fuser heater wire.
Defective engine PWB. 6000
6020
6030
6050 Broken fuser heater wire
Abnormally high fuser thermistor temperature Broken fuser thermistor wire Abnormally low fuser thermistor temperature Deformed connector pin.
Defective triac. 6020 Abnormally high fuser thermistor temperature
The fuser thermistor detects a temperature higher than 230°C/446°F continuously for 40 ms. High fuser temperature signal detects a temperature of 255°C/491°F continuously for 40 ms. Deformed connector pin.
Defective triac.
Shorted fuser thermistor.
Defective engine PWB. 6030 Broken fuser thermistor wire
A/D value of the fuser thermistor exceeds 251 bit continuously for 7 s during warming up. Defective connector cable or poor contact in the connector.
Deformed connector pin.
Defective triac.
Defective fuser thermistor.
Defective engine PWB 6050 Abnormally low fuser thermistor temperature
As the stable temperature has reached the second time, the decrease in the fuser thermistor temperature of 60°C/140°F or greater is detected for one second. Deformed connector pin.
Defective triac.
Defective fuser thermistor
Defective fuser heater.
Defective engine PWB. 6120 Abnormally high fuser thermistor 3 (press roller) temperature
The fuser temperature exceeds 200 °C/392 °F for 1 s. Deformed connector pin.
Defective IH PWB.
Defective fuser thermistor.
Defective engine PWB. 6130 Fuser thermistor 3 (press roller) break error Fuser thermistor 3 detects a temperature of -14 °C/6.8 °F . Fuser thermistor 3 does not reach 30° C/86 °F even after20 s during warming up. Defective connector cable or poor contact in the connector
Deformed connector pin.
Defective IH PWB.
Defective fuser thermistor.
Defective engine PWB. 6150 Abnormally low fuser thermistor 3 (press roller) temperature
The fuser temperature lower than 30 °C/86 °F is detected continuously for 1 s. Deformed connector pin.
Defective fuser thermistor
Defective fuser heater.
Defective engine PWB. 6200 Broken fuser edge heater wire
Fuser thermistor 1 does not reach 50° C/122 °F even after20 s during warming up. The detected temperature of fuser thermistor1 does not reach the specified temperature (ready indication temperature) for 20 s in warming up after reaching 50° C/122 °F. Defective connector cable or poor contact in the connector.
Deformed connector pin.
Fuser thermostat triggered.
Broken fuser heater wire.
Defective engine PWB. 6220 Abnormally high fuser thermistor 1 (edge) temperature
The fuser temperature exceeds 240 °C/464 °F for 1 s Defective connector cable or poor contact in the connector.
Deformed connector pin.
Fuser thermostat triggered.
Broken fuser heater wire.
Defective engine PWB. 6230 Fuser thermistor 1 (edge) break error
During warming up a hearter, fuser thermistor 2 detects a temperature of 100 °C/212 °F or higher and, fuser thermistor 1 detects a temperature of 37 °C/99 °F or lower. Defective connector cable or poor contact in the connector.
Deformed connector pin.
Fuser thermostat triggered.
Broken fuser heater wire.
Defective engine PWB. 6250 Abnormally low fuser thermistor 1 (edge) temperature
The fuser temperature lower than 100 °C/212 °F is detected continuously for 1 s during printing. The fuser temperature lower than 50 °C/122 °F is detected continuously for 1 s during pre-heating. Defective connector cable or poor contact in the connector.
Deformed connector pin.
Fuser thermostat triggered.
Broken fuser heater wire.
Defective engine PWB. 6400 Zero-cross signal error
While fuser heater control is performed, the zero-cross signal is not input within 3 s. Defective connector cable or poor contact in the connector
Defective power source PWB or engine PWB. 6410 Fuser unit type mismatch problem
Absence of the fuser unit is detected. Fuser unit connector inserted incorrectly.
Different type of the fuser unit is installed. 6600 Belt rotation error
The belt was detected to stop for 1 s continuously during motor remote is on. Defective fuser motor.
Defective IH belt.
Defective IH PWB.
Defective engine PWB. 7101 Toner sensor K error Defective Developer unit.
Defective PWB. 7102 Toner sensor C error Defective Developer unit.
Defective PWB. 7103 Toner sensor M error Defective Developer unit.
Defective PWB. 7104 Toner sensor Y error Defective Developer unit.
Defective PWB. 7401 Developing unit K type mismatch problem
Absence of the developing unit K is detected. Developing unit connector inserted incorrectly.
Different type of the developing unit is installed.
Defective PWB. 7402 Developing unit C type mismatch problem
Absence of the developing unit C is detected. Developing unit connector inserted incorrectly.
Different type of the developing unit is installed.
Defective PWB. 7403 Developing unit M type mismatch problem
Absence of the developing unit M is detected. Developing unit connector inserted incorrectly.
Different type of the developing unit is installed.
Defective PWB. 7404 Developing unit Y type mismatch problem
Absence of the developing unit Y is detected. Developing unit connector inserted incorrectly.
Different type of the developing unit is installed.
Defective PWB. 7411 Drum unit K type mismatch problem
Absence of the drum unit K is detected. Drum unit connector inserted incorrectly.
Different type of the drum unit is installed.
Defective PWB. 7412 Drum unit C type mismatch problem
Absence of the drum unit C is detected. Drum unit connector inserted incorrectly.
Different type of the drum unit is installed.
Defective PWB. 7413 Drum unit M type mismatch problem
Absence of the drum unit M is detected. Drum unit connector inserted incorrectly.
Different type of the drum unit is installed.
Defective PWB. 7414 Drum unit Y type mismatch problem
Absence of the drum unit Y is detected. Drum unit connector inserted incorrectly.
Different type of the drum unit is installed.
Defective PWB. 7420 Transfer belt unit type mismatch problem
Absence of the transfer belt unit is detected. Transfer belt unit connector inserted incorrectly.
Different type of the transfer belt unit is installed.
Defective PWB. 7601 ID sensor 1 (front) error Defective ID sensor.
Defective PWB. 7602 ID sensor 2 (rear) error Defective ID sensor.
Defective PWB. 7611 ID sensor (K) density error
When ID sensor 2 detected CTD is 500 or less. Defective ID sensor.
Defective PWB. 7612 ID sensor (C) density error
When ID sensor 2 detected CTD is 500 or less. Defective ID sensor.
Defective PWB. 7613 ID sensor (M) density error
When ID sensor 2 detected CTD is 500 or less. Defective ID sensor.
Defective PWB. 7614 ID sensor (Y) density error
When ID sensor 2 detected CTD is 500 or less. Defective ID sensor.
Defective PWB. 7620 ID sensor timing error
Color registration correction was failed. Defective ID sensor.
Defective PWB. 7800 Broken external thermistor wire
The thermistor output value is 0.3 V or less. Defective connector cable or poor contact in the connector.
Defective temperature sensor. 7810 Short-circuited external thermistor wire
The thermistor output value is 3 V or more. Defective connector cable or poor contact in the connector.
Defective temperature sensor. 7900 Drum unit EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively. Defective connector cable or poor contact in the connector.
Defective drum unit. 7901 Drum K EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively. Defective connector cable or poor contact in the connector.
Defective drum unit. 7902 Drum C EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively. Defective connector cable or poor contact in the connector.
Defective drum unit. 7903 Drum M EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively. Defective connector cable or poor contact in the connector.
Defective drum unit. 7904 Drum Y EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively. Defective connector cable or poor contact in the connector.
Defective drum unit. 7910 Developer unit EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively. Defective connector cable or poor contact in the connector.
Defective developer unit. 7911 Developing unit K EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively. Poor contact in the connector terminals.
Defective developing PWB. 7912 Developing unit C EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively. Poor contact in the connector terminals.
Defective developing PWB. 7913 Developing unit M EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively. Poor contact in the connector terminals.
Defective developing PWB. 7914 Developing unit Y EEPROM error
No response is issued from the device in reading/writing for 5 ms or more and this problem is repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively. Poor contact in the connector terminals.
Defective developing PWB. 8030 Tray upper limit detection problem (document finisher)
When the tray elevation motor raises a tray, the ON status of the tray upper limit sensor is detected. Defective connector cable or poor contact in the connector.
Defective tray upper limit sensor, paper surface sensor 1/2.
Defective DF main PWB. 8040 Belt problem (document finisher)
The belt sensor does not turn on/off within specified time of the belt solenoid turning on. Defective connector cable or poor contact in the connector.
Defective belt sensor.
Defective belt solenoid.
Defective DF main PWB. 8140 Tray elevation motor problem (document finisher)
The tray low limit sensor or paper surface sensor 1/2 cannot be detected to be on within 10 s since the tray elevation motor is activated. Defective connector cable or poor contact in the connector.
Defective connector cable or poor contact in the connector.
The tray elevation motor malfunctions.
Defective tray lower limit sensor, paper surface sensor 1/2.
Defective DF main PWB. 8210 Stapler problem (document finisher)
Jam 7012 or 7023 is indicated. Defective connector cable of staple or poor contact in the connector.
The stapler is blocked with a staple.
The stapler is broken
Defective DF main PWB. 8320 Adjustment motor 2 problem (document finisher)
The adjustment sensor 2 does not turn on/off within specified time of the adjustment motor 2 turning on. Defective connector cable or poor contact in the connector.
Defective adjustment sensor 2.
Defective adjustment motor 2.
Defective DF main PWB. 8330 Adjustment motor 1 problem (document finisher)
The adjustment sensor 1 does not turn on/off within specified time of the adjustment motor 1 turning on. Defective connector cable or poor contact in the connector.
Defective adjustment sensor 1.
Defective adjustment motor 1. 8350 Roller motor problem (document finisher)
The roller sensor does not turn on/off within specified time of the roller motor turning on. Defective DF main PWB.
Defective connector cable or poor contact in the connector.
Defective roller sensor.
Defective roller motor.
Defective DF main PWB. 8360 Slide motor problem (document finisher)
The slide sensor does not turn on/off within specified time of the slide motor turning on. Defective connector cable or poor contact in the connector.
Defective slide sensor.
Defective slide motor.
Defective DF main PWB. 8460 EEPROM problem (document finisher)
Reading from or writing to EEPROM cannot be performed. Defective EEPROM or DF main PWB. 8800 Document finisher communication error
A communication error is detected 10 times in succession. Defective connector cable or poor contact in the connector
Defective DF main PWB.
Defective engine PWB. 8830 Bridge communication error (document finisher)
A communication error is detected 10 times in succession. Defective connector cable or poor contact in the connector.
Defective bridge PWB.
Defective engine PWB. 8990 Document finisher communication error Defective connector cable or poor contact in the connector.
Defective DF main PWB.
Defective bridge PWB. 9000 Document processor communication error
A communication error is detected 10 times in succession. Defective connector cable or poor contact in the connector.
Defective DP main PWB. 9060 DP EEPROM error Read and write data does not match. Data in the specified area of the backup memory does not match the specified values. Defective DP main PWB.
Device damage of EEPROM. 9500 BRU communication error IPU PWB error 9510 BRU PWB error IPU PWB error 9520 BRU PWB data error IPU PWB error F000 Main PWB — operation panel PWB communication error Defective main PWB.
Defective operation panel PWB. F010 Main PWB checksum error Defective main PWB. F040 Main PWB — print engine communication error Defective main PWB.
Defective engine PWB. F050 Print engine ROM checksum error Defective engine PWB.

1. 08-15-2016

   
   

   #1

   

   
   Junior Member
   

   

   

   ---

   Rep Power

   0

   Kyocera P6035cdn error C4600
   

   Hi Guys,

   I’ve been stuck with a Kyocera ECOsys P6035cdn that is driving me crazy!!!, it keeps giving me a C4600 error which is the LSU cleaning motor error.To date:

   -> I’ve upgraded to the latest available firmware,

   -> Followed the LSU cleaning motor service bulletins and greased the relevant gears and shafts,

   -> Replaced the Engine Relay as prescribed in the service manual.

   STILL NO JOY!!!

   Anybody have any other options for me to try or ideas other than matches and petrol?

   Thanks.

   ---

2. 08-16-2016

   
   

   #2

   

   
   Technician
   

   

   ---

   Rep Power

   14

   Re: Kyocera P6035cdn error C4600
   

   there is bulletin for the same code

   ---

3. 08-16-2016

   
   

   #3

   

   
   Junior Member
   

   

   

   ---

   Rep Power

   0

   Re: Kyocera P6035cdn error C4600
   

   @TECHKYO, Yes…I saw the service bulletin and did the modifications but the error msg: C4600 still comes back.

   ---

4. 08-16-2016

   
   

   #4

   

   
   Trusted Tech
   

   50+ Posts

   

   ---

   Rep Power

   18

   Re: Kyocera P6035cdn error C4600
   

   unplug the cleaning motor from the pcb
   It has been working so far.

   ---

5. 10-12-2016

   
   

   #5

   

   
   Junior Member
   

   

   

   ---

   Rep Power

   0

   Re: Kyocera P6035cdn error C4600
   

   ---

6. 11-14-2018

   
   

   #6

   Re: Kyocera P6035cdn error C4600
   

   
   I’ve got a couple of M6535cidn in a very dusty warehouse with the same problem. I’ve unplugged the cleaning motors on both, which got rid of the codes, but I have to manually clean them every few weeks, which is getting old!

   If replacing the LSUs would make a permanent fix I would gladly do it, but I haven’t seen anything about modifications to them.

   So, it’s been a while since you replaced both LSUs… Did that permanently fix the problem???

   Thanks for your reply,

   Robert B.
   Atlanta, GA

   ---

7. 11-14-2018

   
   

   #7

   

   
   Trusted Tech
   

   50+ Posts

   

   

   

   ---

   Rep Power

   27

   Re: Kyocera P6035cdn error C4600
   

   We have modified several of this series machines with some success. We have found that the cleaning motor will need to be replaced and possibly the left connect board to eliminate the error code. While replacing the motor, you can modify the lasers with mylar pieces to help the cleaners get on the glass of the laser. This has eliminated the problem on several machines for us. I will post a link to a video that we made describing the modification. I have sent this to Kyocera with no response from them except that they have tried it also with success, but never bothered to let anyone know about it.

   https://drive.google.com/open?id=1Bn…ZO9ccRJiJP0WL5

   ---

8. 01-22-2019

   
   

   #8

   

   
   Junior Member
   

   

   ---

   Rep Power

   0

   Re: Kyocera P6035cdn error C4600
   

   I tried all of the above, but I wasn’t settling on having to go back once a month to pull the 4 devs, 4 drums, belt, 4 toners out and wipe 4 slits of glass because of a unplugged motor. I replaced the «Inner Left Duct» (pn= 302NR33020) which is the black plastic housing for the drive train for all 4 LSU cleaners. Don’t forget to grease those gears either. Fairly easy job after having to pull everything out a dozen times.

   ---

Если с аппаратом Kyocera TASKalfa 1800, Kyocera TASKalfa 2200 произошла проблема, откроется следующий экран с уведомлением.
• Индикатор [Внимание] на панели управления горит или мигает.
• На дисплее сообщений панели управления аппарата появилось сообщение об ошибке.

Если индикатор [Внимание] горит или мигает и на дисплее сообщений панели управления аппарата появилось сообщение об ошибке, проверьте KYOCERA Client Tool или Монитор состояния.

ПРИМЕЧАНИЕ Если индикаторы постоянно горят и мигают не так, как описано выше, вероятно, произошла ошибка службы. Выключите питание, отсоедините шнур питания и вставьте его обратно, после чего включите питание. Это может помочь сбросить ошибку. Если ошибка не исчезает, свяжитесь со своим представителем сервисной службы (тел. в Минске +375 17 291-28-24)

Ниже описаны неполадки, которые не могут быть устранены пользователем

Дисплей сообщений	Описание	Меры устранения
Бункер отраб тонера перепол. или не уст.	Бункер для отработанного тонера установлен неправильно	Установите Бункер для отработанного тонера должным образом
Бункер для отработанного тонера заполнен	Замените бункер отработанного тонера
Встряхните картр. с тонером	Тонер слежался	Откройте переднюю крышку аппарата и вытяните контейнер с тонером. Сильно встряхните контейнер с тонером и установите его на место
Вызовите сервисный персонал.	В аппарате произошла ошибка	Обратите внимание на код ошибки, отображаемый в дисплее сообщений, и свяжитесь с представителем сервисной службы (тел. в Минске +375 17 291-28-24)
Выньте бумагу с внутреннего лотка		Извлеките бумагу из внутреннего лотка. Нажмите клавишу [OK], чтобы возобновить печать
Добавьте тонер	Закончился тонер	Замените контейнер с тонером TK-4105
Загрузите бумагу в кассету #	↑↓ (отображается попеременно) A4 (формат бумаги) Обычная (тип носителя) OK: Перейдите к следующему шагу	Загрузите бумагу. Нажмите клавишу [OK] и перейдите к следующему шагу. • Для выбора другого устройства подачи выберите [Выберите бумагу]. • Для печати на бумаге, в настоящее время находящейся в устройстве подачи, выберите [Продолж. без изм.]
Загрузите бумагу в универсальный лоток	↑↓ (отображается попеременно) A4 (формат бумаги) Обычная (тип носителя) OK: Перейдите к следующему шагу	Загрузите бумагу. Нажмите клавишу [OK] и перейдите к следующему шагу. • Для выбора другого устройства подачи выберите [Выберите бумагу]. • Для печати на бумаге, в настоящее время находящейся в устройстве подачи, выберите [Продолж. без изм.]
Закройте автоподатчик оригиналов	Открыт автоподатчик оригиналов	Откройте и закройте автоподатчик оригиналов
Закройте крышку автопод. оригиналов	Открыта верхняя крышка автоподатчика оригиналов	Откройте и закройте крышку автоподатчика оригинало
Закройте переднюю крышку	Открыта передняя крышка	Откройте и закройте переднюю крышку
Закройте правую крышку #	Открыта какая-либо крышка	Откройте и закройте крышку, обозначенную на экране
Замятие бумаги. (DP) ↑↓ (отображается попеременно) Проверьте (B)(C) в крышке DP	В автоподатчике произошло замятие бумаги.	См. Устранение замятия бумаги в Руководстве по эксплуатации и извлеките замятую бумагу
Замените МК	Необходимо производить замену деталей комплекта техобслуживания MK-4105 (ремкомплекта) каждые 150 000 страниц печати.	Данная операция должна производиться специалистом. Обратитесь к представителю сервисной службы (тел. в Минске +375 17 291-28-24)
Замятие	Произошло замятие бумаги в кассете или универсальном лотке	См. Устранение замятия бумаги и извлеките замятую бумагу
Извлеките оригиналы из автоподатчика	Для продолжения работы необходимо извлечь оригиналы из автоподатчика оригиналов	Извлеките оригиналы из автоподатчика оригиналов
Кабель USB был отключен	Кабель USB не подключен	Нажмите клавишу [OK] и подключите кабель USB
ПК выключен	Нажмите клавишу [OK] и включите ПК
Не удается найти KYOCERA Client Tool	Нажмите клавишу [OK] и откройте KYOCERA Client Tool на ПК
Макс. к-во сканируемых страниц	Превышен предел сканирования	Дальнейшее сканирование невозможно. Задание отменено. Нажмите клавишу [OK]
Мало тонера. (Зам., когда законч.)	Скоро понадобится заменить контейнер с тонером	Получите новый контейнер с тонером TK-4105.  Внимание! Когда заканчивается тонер аппарат перестает печатать
Не оригинальный тонер	Установлен контейнер с тонером не марки Kyocera	Производитель не несет ответственности за повреждения, вызванные использованием неоригинального тонера. Мы рекомендуем использовать исключительно оригинальные контейнеры с тонером  TK-4105. . Если нужно использовать установленный в настоящее время контейнер с тонером, нажмите одновременно и удерживайте клавиши [OK] и [Стоп] в течение не менее 3 с.
Неверный ид. уч. зап. Задание отменено	Указан неверный идентификатор учетной записи при внешней обработке задания. Задание отменено	Нажмите клавишу [OK]
Невозможна двусторонняя печать на этой бумаге	Не возможна печать на бумаге выбранного формата или типа	Нажмите клавишу [OK] и перейдите к следующему шагу: • Для выбора другого устройства подачи выберите пункт [Выберите бумагу]. • Чтобы печатать, не используя функцию двусторонней печати, выберите пункт [Продолж. без изм.].
Недостаточно памяти. Невозможно начать выполнение задания	Невозможно начать выполнение задания	Повторите попытку позже
Ограничено алгоритмом учета заданий(Печать)	Задание отменено, поскольку его выполнение ограничено функцией учета заданий	Нажмите клавишу [OK]
Ограничено алгоритмом учета заданий(Сканер)	Задание отменено, поскольку его выполнение ограничено функцией учета заданий	Нажмите клавишу [OK]
Очистите сканер	Произошло загрязнение сканера	Очистите щелевое стекло с помощью чистящей салфетки, поставляемой вместе с автоподатчиком оригиналов.
Ошибка. Выключить	—	Отключите и снова включите аппарат с помощью выключателя питания
Память переполнена	Невозможно продолжить выполнение задания из-за отсутствия свободной памяти	Измените разрешение печати с Быстр1200 до 600 dpi. См. Printer Driver User Guide
Память сканера переполнена	Дальнейшее сканирование невозможно из-за нехватки памяти сканера.	Для отмены задания нажмите [OK]
Перезагрузка печати. Задание отменено	Предупреждение. Недостаточно памяти принтера. Задание отменено	Нажмите клавишу [OK]
Превышено ограничение учета заданий	Превышено число распечаток из-за ограничения алгоритмом учета заданий. Достигнут предел печати	Это задание отменено. Нажмите клавишу [OK]
Уст.другую кассету	Выбрано «Сдвиг»	Для использования сдвига необходимо загрузить в другой лоток бумагу такого же формата, что и в выбранном устройстве подачи, но в другой ориентации
Установите все оригиналы обратно и нажмите клавишу [Старт].	Возникает при печати двусторонних документов в режиме ручной двусторонней печати	Извлеките оригиналы из автоподатчика оригиналов, расположите их в первоначальном порядке и положите обратно. Нажмите клавишу [OK], чтобы возобновить печать. Для отмены задания нажмите [Стоп]
Установлен неизвестный тонер. ПК	Региональная спецификация контейнера с тонером не соответствует спецификации аппарата	Установите оригинальный контейнер с тонером Замените контейнер с тонером TK-4105