Kyocera m2040dn ошибка c6050

Коды ошибок Kyocera

Коды ошибок принтеров Kyocera

Рекомендуем хорошие сервисы по ремонту принтеров.

Наши мастера ежедневно отвечают на большое количество вопросов по ремонту принтеров Kyocera. Ознакомьтесь с волнующими вас вопросами ниже, или же задайте свой вопрос, на который мы с радостью ответим!

Была ли полезна для Вас статья ?

Оставляйте свои вопросы и отзывы по ремонту принтеров. Мы рады ответить на все ваши вопросы и обязательно учтём ваши отзывы в дальнейшей работе Юмедиа Сервиса.

Оставьте первый вопрос или отзыв о Юмедиа по ремонту принтеров!
Уже чинили аппарат у нас? Оставьте свой рейтинг!
Оцените работу движка
Ваша оценка: Текущий рейтинг: 4.81 (Проголосовало: 7)
+7 (812) 666-1-555

Источник: remont3.ru

Коды ошибок Kyocera

Работая с аппаратами Kyocera можно столкнуться с неисправностями, которые появляются на дисплее в виде кода. Но не все ошибки легко исправляются, многие из них требуют серьёзной диагностики и замены деталей.

Kyocera сбой аппарата. Ошибка C2010

В этом списке перечислены лишь основные коды ошибок (на самом деле их гораздо больше):

Код ошибки Причина возникновения
C0100 Backup memory (EEPROM) device problem (main) (не может быть выполнено чтение или запись в EEPROM)
C0110 Backup memory data problem (main) (проблема резервного копирования данных в память)
C0150 Backup memory device problem (engine EEPROM) (проблема в двигателе EEPROM)
C0160 Backup memory data problem (engine EEPROM) (проблема в двигателе EEPROM)
C0170 Copy counts problem (проблема счетчика копий)
C0180 Machine number mismatch (не совпадает номер аппарата и главного двигателя)
C0210 Communication problem between the main and engine (проблема связи между платой и двигателем)
C0240 Printer PWB communication problem (проблема с питанием)
A0410 Document processor communication problem (сбой связи процессора)
A0420 First paper feeder communication problem (проблема с первым податчиком бумаги)
A0500 Second paper feeder communication problem (проблема со вторым податчиком бумаги)
A0510 Third paper feeder communication problem (проблема с третьем податчиком бумаги)
C0610 Bitmap (DIMM) problem (проблемы с данными или адресной шиной растрового изображения DRAM)
C0620 Memory input interface problem (проблема памяти интерфейса ввода)
C0630 DMA problem (проблема DMA)
C0800 Image processing problem (проблема обработки изображения)
C2000 Drive motor problem (проблема двигателя привода)
C2200 Drum motor problem (проблема двигателя драма)
C3100 Scanner carriage problem (проблема каретки сканера)
C3200 Exposure lamp problem (проблема лампы экспонирования)
C3300 AGC problem (проблема AGC)
C4000 Polygon motor synchronization problem (проблема синхронизации двигателя полигона)
C4010 Polygon motor steady–state problem (проблема двигателя полигона)
C4200 BD steady–state problem (проблема BD)
C6000 Fuser heater break (неисправность нагревателя печки)
C6020 Abnormally high fuser thermistor temperature (аномально высокая температура термистора в печке)
C6050 Abnormally low fuser thermistor temperature (аномально низкая температура термистора в печке)
C6400 Zero–cross signal error (ошибка нулевого сигнала)
C7800 Broken external thermistor wire (поломка внешних проводов термистора)
C7810 Short–circuited external thermistor wire (короткое замыкание термистора)

FS-1040 вычисление кода ошибки.

Источник: hcolor.ru

Наиболее распространённые ошибки принтеров Kyocera

Современные принтеры и копировальные аппараты Kyocera умеют диагностировать узлы устройства при запуске, а также в период функционирования устройства. Если происходит сбой, техника выдаёт ошибку. Определённый код появляется на дисплее и в Мониторе состояния, также могут начать мигать индикаторы. При отсутствии экрана нужно смотреть на светодиоды.

Они укажут на то, что появилась проблема. Необходимо ориентироваться на частоту мерцания для выявления неисправности. В инструкции к аппарату будет указано, на что указывают светодиоды. Необходимо рассмотреть коды ошибок, а также способы их устранения.

5d316f6b40681343275067_500.jpg

Распространённые ошибки принтеров Kyocera

1err.jpg

Если на дисплее появится надпись E-0001, то это говорит о повреждении чипа расходника или установке несовместимого картриджа.

Как решить проблему:

2err.jpg

Когда на дисплее появляется E-0002, это указывает на несоответствие региона используемого картриджа характеристикам принтера.

Пути решения:

  1. Поставить картридж, который будет соответствовать региону устройства для печати.
  2. Выполнить замену чипа.
  3. Прошить принтер.

3err.jpg

Если на экране отобразится надпись E-0003, это укажет на заполнение памяти устройства. Нужно выполнить сброс операции или распечатать ранее отсканированные бумаги.

4err.jpg

Надпись E-0012 говорит о том, что память печатного устройства заполнена. Нужно поменять разрешение печати до 600 dpi.

5err.jpg

Код E-0015 появляется по следующим причинам:

  1. Не подаётся питание к принтеру.
  2. Не подсоединён сетевой кабель.
  3. На ПК отсутствует нужный драйвер.

Следует проверить сетевой кабель, чтобы убедиться в отсутствии повреждений. Затем нужно включить прибор. Если проблема осталась, понадобится провести установку драйвера.

Когда ошибку не удаётся устранить самостоятельно, вы можете обратиться к специалистам сервисного центра ОТК в городе Краснодар. Наши мастера проведут диагностику, выявят и устранят неисправность.

Источник: otk1.ru

Устранение ошибки передачи – Инструкция по эксплуатации Kyocera Ecosys m2040dn

background image

Проверьте правильность имени хоста SMTP
сервера в Command Center RX.

Не удалось отправить через
FTP.

Проверьте имя хоста FTP.

Не удалось отправить через
SMB.

Проверьте имя хоста SMB.

Не удалось отправить через
SMB.

Проверьте настройки SMB:

имя пользователя и пароль при входе.

Если отправитель является пользователем
домена, укажите имя домена:

Не удалось отправить
электронную почту.

Проверьте следующее на Command Center RX:

имя пользователя и пароль для сервера SMTP;

имя пользователя и пароль для сервера POP3;

предел размера сообщения эл. почты.

Не удалось отправить через
FTP.

Проверьте настройки FTP-сервера:

имя пользователя и пароль при входе.

Если отправитель является пользователем
домена, укажите имя домена:

право доступа получателя к папке.

Не удалось отправить через
SMB.

Проверьте настройки SMB:

имя пользователя и пароль при входе.

Если отправитель является пользователем
домена, укажите имя домена:

право доступа получателя к папке.

Не удалось отправить через
FTP.

Проверьте настройки FTP-сервера:

право доступа получателя к папке.

Не удалось отправить
электронную почту.

Проверьте адрес электронной почты.

Если адрес отклонен доменом, отправка
электронного письма невозможна.

Источник: www.manualsdir.ru

Первое новое сообщение • Сообщений: 23
• Страница 1 из 1

Шандор
новичок
 
Сообщения: 17
Зарегистрирован: 22:34 — 18.10.16
Баллы репутации: 0

Mishel01
эксперт
 
Сообщения: 8413
Зарегистрирован: 01:10 — 10.01.11
Баллы репутации: 1

Шандор
новичок
 
Сообщения: 17
Зарегистрирован: 22:34 — 18.10.16
Баллы репутации: 0

Шандор
новичок
 
Сообщения: 17
Зарегистрирован: 22:34 — 18.10.16
Баллы репутации: 0

Шандор
новичок
 
Сообщения: 17
Зарегистрирован: 22:34 — 18.10.16
Баллы репутации: 0

Шандор
новичок
 
Сообщения: 17
Зарегистрирован: 22:34 — 18.10.16
Баллы репутации: 0

Шандор
новичок
 
Сообщения: 17
Зарегистрирован: 22:34 — 18.10.16
Баллы репутации: 0

Шандор
новичок
 
Сообщения: 17
Зарегистрирован: 22:34 — 18.10.16
Баллы репутации: 0

Mishel01
эксперт
 
Сообщения: 8413
Зарегистрирован: 01:10 — 10.01.11
Баллы репутации: 1

Шандор
новичок
 
Сообщения: 17
Зарегистрирован: 22:34 — 18.10.16
Баллы репутации: 0

Шандор
новичок
 
Сообщения: 17
Зарегистрирован: 22:34 — 18.10.16
Баллы репутации: 0

Re: Kyocera FS 6525 MFP код ошибки 6050 Помогите пожалуйста!

Непрочитанное сообщение Mishel01 » 21:59 — 28.10.16

Вот и я об этом как раз: после поста от 20 октября вы можете ждать сколько угодно — надеюсь, понятно, почему.
Правды в вашем наезде — 0,00%, а ваше личное мнение тут мало кого интересует — тоже, надеюсь, понятно, почему.
Простите, а вы много тут успели напомогать? Что-то как-то незаметно было.

Mishel01
эксперт
 
Сообщения: 8413
Зарегистрирован: 01:10 — 10.01.11
Баллы репутации: 1

Шандор
новичок
 
Сообщения: 17
Зарегистрирован: 22:34 — 18.10.16
Баллы репутации: 0

Шандор
новичок
 
Сообщения: 17
Зарегистрирован: 22:34 — 18.10.16
Баллы репутации: 0

Шандор
новичок
 
Сообщения: 17
Зарегистрирован: 22:34 — 18.10.16
Баллы репутации: 0

Шандор
новичок
 
Сообщения: 17
Зарегистрирован: 22:34 — 18.10.16
Баллы репутации: 0

Шандор
новичок
 
Сообщения: 17
Зарегистрирован: 22:34 — 18.10.16
Баллы репутации: 0

Mishel01
эксперт
 
Сообщения: 8413
Зарегистрирован: 01:10 — 10.01.11
Баллы репутации: 1

Шандор
новичок
 
Сообщения: 17
Зарегистрирован: 22:34 — 18.10.16
Баллы репутации: 0

Шандор
новичок
 
Сообщения: 17
Зарегистрирован: 22:34 — 18.10.16
Баллы репутации: 0

Mishel01
эксперт
 
Сообщения: 8413
Зарегистрирован: 01:10 — 10.01.11
Баллы репутации: 1

Шандор
новичок
 
Сообщения: 17
Зарегистрирован: 22:34 — 18.10.16
Баллы репутации: 0

Mishel01
эксперт
 
Сообщения: 8413
Зарегистрирован: 01:10 — 10.01.11
Баллы репутации: 1


Сообщений: 23
• Страница 1 из 1

  • Похожие темы
    Ответы
    Просмотры
    Последнее сообщение

Вернуться в KYOCERA

Кто сейчас на конференции

Сейчас этот форум просматривают: нет зарегистрированных пользователей и гости: 0

Содержание

  1. Kyocera m2040dn error c6600
  2. Kyocera m2040dn error c6600
  3. Kyocera M2040 Сбой аппарата | Service call c6600
  4. Дмитрий Щетнев
  5. Mesya Wandangpai
  6. Lucas bike
  7. Recoil Denis
  8. Eugene Gerasichkin
  9. froilan gomez
  10. Алексей Ш.
  11. Иван Иванов
  12. Nageswara Rao
  13. A Gamerz
  14. Денис Серебряков
  15. Fariyaan khan
  16. Papa Carlo
  17. Hamza Hamza
  18. sebastian pereiro
  19. Tech2Gadgetgyaan
  20. CyXaRb
  21. Виталий Охрименко
  22. Ошибка C6610 в принтерах Kyocera — причины и решение
  23. Причины возникновения
  24. Исправление
  25. Проверка двигателя прижима печки Kyocera M2040/P2235DN (C6610)

Kyocera m2040dn error c6600

КОНФЕРЕНЦИЯ СТАРТКОПИ
Принтеры, копировальные аппараты, МФУ, факсы и другая офисная техника:
вопросы ремонта, обслуживания, заправки, выбора

0. Max958166 19.06.19 18:23

Всем здравствуйте.
Пришел аппарат с замятием в задней крышке, пробег 25500. Ну ясен пень вскрыл печь, сказка пересохла и ткань уже была надорвана, но в гармошку ещё не собралась. Заменил данную тряпченку, собрал печуху, собственно и появилась данная ошибка.
Лампа звонится, предохранители звонятся, термистр выдает 194кОм, храповик целый, пружину усилил.
Пробовал сбросить печную ошибку из сервисного меню, код u167 не работает ( Подскажите, пожалуйста, в какую сторону глядеть, и как всё-таки сбрасываются печные ошибки на данной модели?

Description
Fuser rotation error The fuser roller rotation detection is not input for consecutive 2s while the motor’s steady signal is input

Remedy
Fuser unit 1. Make sure there is no paper jam. 2. Confirm that the wiring connector is firmly connected, and if necessary, connect the connector all the way in. Fuser unit — Main/Engine PWB(YC19) 3. If the wiring is disconnected, shortcircuited or has a ground fault, replace the wire. 4. Replace the fuser unit.
Main/Engine PWB Replace the main/engine PWB.

2. Max958166 19.06.19 20:50

Спасибо за ссылку. Но не могу понять, ошибка вращения. Двигатель запускается, печка крутится, замятия нет. Поменять печку — это, конечно, проще простого, но мы не ищем лёгких путей. Может действительно коротить, надо завтра проверить.

Забыл одеть шестереночку оптопары вращения резвала? Левая крышечка печки. Противоположенная от той что с проводами.

Там энкодер своеобразный. Причем подпружиненный. На нем должно быть шестеренчатое кольцо с тремя шлицами. Либо не поставил промежуточное от энкодера к резиновому валу. а?

Случай был, клиент продул сабж, пришлось оптопару чистить..

Храповик целый на 302RV94020 Площадка привода термоблока?

7. Max958166 20.06.19 08:48

(3) Шестерёнка точно на месте. Промежуточное кольцо погляжу, сейчас сложно вспомнить.
(5) Попробую почистить.
(6) Храповик целый, печка запускается двигателем.

а коннекторы нормально вставлены?

10. Max958166 20.06.19 15:19

(8) Ты оказался прав, шестерни на месте не было. Спасибо огромное за наводку. Теперь буду знать.

Источник

Kyocera m2040dn error c6600

КОНФЕРЕНЦИЯ СТАРТКОПИ
Принтеры, копировальные аппараты, МФУ, факсы и другая офисная техника:
вопросы ремонта, обслуживания, заправки, выбора

0. eldor111 24.01.22 11:23

есть аппарать kyocera p2040dn. с ошибкой 6600 сталкивался часто, проблема вроде как понятна.. но.

на экранчике высечивается: «обратитесь в сервис 6600:0133255»
свою рабочую печку подкинул (нужно было тупо пробег посмотреть), а ошибка осталась. в мануале по этому поводу пишут (проверьте разьем YC19, замените печку или плату) решил перекинуть Engine PWB, чтобы локализовать проблему и ошибка поменялась на: обратитесь в сервис 6600:0001665.

кстати «нерабочую» печку не разбирал, но в свой аппарат воткнул — все отлично работает. своя печь на родном аппарате тоже работает. другие платы и главный мотор(хз зачем) тоже менял, без толку. кто сталкивался с таким?

1. Владимир А. 24.01.22 11:56

eldor111 (0): свою рабочую печку подкинул (нужно было тупо пробег посмотреть), а ошибка осталась.
Так пробег же написан в ошибке! 6600:0133255 133255 и есть пробег аппаратика.

2. conductor 24.01.22 12:53

C6600: Fuser rotation error

Шестеренка храповика, черненькая такая, даже не шестеренка , а сама трещётка, наверняка сломана. Поэтому редуктор не крутит печь.

Кстати, кто-нибудь знает, есть ли отдельно эта шестеренка? Я не нашел, но возможно китайские товарищи делают?
Судя по парт-каталогу доступен только редуктор в сборе.
302RV94020 — Площадка привода термоблока P2235dn, P2040dn

Lex (4): есть ли отдельно эта шестеренка?
Ни один из моих поставщиков не смог.
У дядюшки Ляо на тот момент тоже небыло.
Ставил редуктор в сборе.

Но хотя если поискать, то приводы в сборе есть по такой же примерно цене

(6)То, что надо! А я не смог найти. Спасибо.

PM012 (6): приводы в сборе есть по такой же примерно цене
Вот тут не понял? Весь храповик имеется ввиду? Не полностью редуктор, а именно храповик? Так в нем больше ничего и не ломается. Эта шестеренка там, как раз, как предохранитель.

(7) мы покупали весь редуктор за 500 руб (декабрь м-ц 2021). а тут цена за деталь плюс пересылка — примерно такая же сумма

(7) Так в нем больше ничего и не ломается поверьте, ломается

10. eldor111 25.01.22 08:54

Владимир А. спасибо, да, что то я про привод печи то недопер. там сам корпус привода треснут..

Источник

Kyocera M2040 Сбой аппарата | Service call c6600

Просмотров: 10 615

30 сентября 2019

Если вам понравилось бесплатно смотреть видео kyocera m2040 сбой аппарата | service call c6600 онлайн которое загрузил Дмитрий Щетнев 30 сентября 2019 длительностью 00 ч 07 мин 00 сек в хорошем качестве, то расскажите об этом видео своим друзьям, ведь его посмотрели 10 615 раз.

Дмитрий Щетнев

Помогло видео? Поддержать канал (карта сбера) 5336690260376886
QIWI кошелек +79274355199

Mesya Wandangpai

kalau eror c6020 kenapa itu?

Lucas bike

Soo good, but if u can, put lyrics
I dont understood nothing if you say
I junst see what you doo 🇧🇷🇧🇷

Recoil Denis

Есть подобный аппарат только со ошибкой с6610 . Термо блок крутится, но не греется . Замена редуктора привода термо блока и блока питания с заведомо рабочего аппарата никчему хорошему не привело , та же самая ошибка . Установка термо блока с не рабочего аппарата на рабочий аппарат , все в порядке, ошибки нет. В чем может быть еще проблемам ?

Eugene Gerasichkin

Как раз такой сейчас на столе. Только у меня веселее — печка не виновата. Моторчик с противоположной от редуктора стороны не запускается. Причем сам моторчик тоже не виноват, проверено донором. Дальше в Main путь идет

froilan gomez

Алексей Ш.

Дмитри, прошу прощения за вопрос не по видео, но ближе не нашёл темы. Аппарат (M2040dn) начал иногда вываливаться в ошибку С6050. Перезагрузка решает проблему не на долго. Что за беда? Гуглёж подсказал проверить питание в розетке. Там 215в. а при печати и прогреве может быть и 210. При этом может и свет моргать не много. Но свет моргал там всю дорогу, и ничего подобного не выскакивало. Печь в данном аппарате довольно сильно изношена, термоткань заменена, периодически требуется подмазывать.

Иван Иванов

Спасибо за видео. Долго искал ошибку, оптопару пропустил.

Nageswara Rao

Bro try to do a video on disassemble the total ADF section of 2040

A Gamerz

Please mujhe c 6650 code ke bare me btaye

Денис Серебряков

Увидел в ролики твоем что там ролики стоят с али случаной не подскажешь не дашь ссылку если знаешь где закать и какой ресурс этих роликов

Fariyaan khan

Sir I need Your Help I am using same C3100 Problem Please Solve my Problem

Papa Carlo

Hamza Hamza

Kyocera m2030dn error machine Failuer call service cf010

sebastian pereiro

Дмитрий после продувки сжатым воздухом в другом сц 🙂 такая же ошибка узел вращается,сам силиконовый ролик весь грязный конечно же,в чём может быть причина? засыпало датчик?

Tech2Gadgetgyaan

Pls provide reason of error. toner container improperly installed. only when using refilled cartridge. with new cartridge, works fine

CyXaRb

Кому оптом редукторы по 300р новые )))

Виталий Охрименко

слышал недавно такую новость : новые печки Kyocera не ходят более 20т. и вроде как сама kyocera подтвердила это все! но исправлять не будут. слышал кто или нет такое. по поводу канала Дмитрий. просто бомба. сам инженер на выезде. но с глубоким ремонтом не особо. поэтому усиленно слежу за вашим каналом и он очень помогает. респект вам за то, что делитесь своим опытом с др. людьми. Огромное спасибо.

Источник

Ошибка C6610 в принтерах Kyocera — причины и решение

C6610 — «Ошибка датчика снижения давления фьюзера (блока термозакрепления)».

Актуальна для моделей лазерных принтеров Kyocera:

Причины возникновения

Фьюзер (блок термозакрепления, термоблок, «печка») в лазерном картридже закрепляет тонер на бумаге с помощью нагрева и давления. Состоит, обычно, из двух роликов: верхний нагревает тонер, а нижний контролирует его прижимание к бумаге (подробнее об устройстве лазерного картриджа).

Прижимание, в зависимости от толщины бумаги, обеспечивает давление компрессора (Fuser Pressure Release Motor). За контроль давления отвечает специальный датчик (Pressure Release Sensor). Ошибка C6610 появляется, когда датчик не фиксирует необходимого для печати изменения давления. То есть, может быть как отказ работы компрессора, так и сбой в работе датчика.

Исправление

Ошибка C6610 говорит о поломке одного из элементов блока термозакрепления. Для её исправления необходимо либо менять его весь, либо проводить тщательную диагностику и менять неисправную деталь. В обоих случаях, процедуру лучше доверить сервисному инженеру. Попытки ремонтировать принтер своими руками, без специальных знаний о его устройстве, могут привести к выходу из строя и других элементов.

Выдержка из оригинальной инструкции по решению причинам и способам решения ошибки C6610.

1 Reinstalling the fuser unit (Переустановка блока фьюзера)

The drawer connector of the fuser unit is not properly inserted.
Соединитель ящика блока термозакрепления вставлен неправильно.

Check if the pins of the drawer connector of the fuser unit do not bend. If it bend, replace the fuser unit. When the pins are proper, reinstall the fuser unit so that the drawer connector firmly connects.
Проверьте, не согнуты ли контакты разъема ящика блока термозакрепления. Если он изгибается, замените блок термического закрепления. Когда штифты правильные, переустановите блок термоблока так, чтобы соединитель выдвижного ящика плотно соединялся.

2 Checking the wire (Проверка провода)

The wire is not properly connected or is faulty.
Провод неправильно подключен или неисправен.

Execute U030 [Fuser Release] to check the fuser release motor operation. If it does not operate properly, reinsert the following wire connectors. Then, replace the wires if there is no continuity.
Выполните U030 [Снятие фьюзера], чтобы проверить работу двигателя сблокировки термоблока. Если он не работает должным образом, вставьте следующие разъемы. Затем замените провода, если нет непрерывности.

3 Replacing the fuser unit (Замена блока термозакрепления)

The fuser unit is faulty at the fuser pressure release mechanism or the fuser pressure release sensor .
Блок термозакрепления неисправен в механизме сброса давления термофиксатора или в датчике сброса давления термофиксатора.

Replace the fuser unit.
Замените блок термозакрепления.

4 Firmware upgrade (Обновление прошивки)

The firmware is not the latest version.
Прошивка не последней версии.

Upgrade the engine firmware to the latest version
Обновите прошивку двигателя до последней версии.

5 Replacing the feed drive PWB (Замена подающего устройства PWB)

The feed drive PWB is faulty.
Неисправность PWB привода подачи.

Replace the feed drive PWB.
Неисправность PWB привода подачи.

6 Replacing the engine PWB (Замена двигателя PWB)

The engine PWB is faulty.
Двигатель PWB неисправен.

Replace the engine PWB.
Замените PWB двигателя.

7 Replacing the feed image PWB (Замена канала PWB)

The feed image PWB is faulty.
Ошибка PWB канала подачи.

Replace the feed image PWB.
Замените PWB изображения канала.

8 Replacing the fuser release motor (Замена двигателя для выпуска термоблока)

The fuser release motor is faulty.
Неисправен двигатель выпуска термоблока.

Replace the fuser release motor.
Замените двигатель выключения термоблока.

9 Replacing the gear in the fuser pressure releasing system at the main unit (Замена шестерни в системе выпуска давления фьюзера на основном блоке)

The gear of the fuser pressure releasing mechanism at the main unit is faulty.
Неисправны шестерни механизма выталкивания фьюзера на главном блоке.

Replace the gears in the fuser pressure releasing mechanism at the main unit.
Замените шестерни в механизме отпускания фьюзера на основном блоке.

Источник

Проверка двигателя прижима печки Kyocera M2040/P2235DN (C6610)

В видеоролике к данной статье мы хотим показать способы проверки двигателя прижима печки печатающих устройств Kyocera серии M2040:

  • МФУ M2135DN, M2635DN, M2735DW и принтеры P2235DN, P2235DW — со скоростью 35 ppm,
  • МФУ M2040DN, M2540DN, M2640IDW и принтеры P2040DN, P2040DW — 40 ppm

Указанные машины вышли на рынок в конце 2016 года на смену серии M2030/2535, у которой наиболее популярной «болячкой» был разрыв тефлонового (нагревательного) вала блока фиксации FK-171E.

В обновленной линейке компания KYOCERA применила принципиально новую для себя технологию закрепления с терморемнем и галогеновой лампой нагрева.

Это решение позволило снизить энергопотребление и использовать тонер на основе полиэстера — температура его закрепления ниже, чем у предшественников.

Однако, спутником любой новой технологии являются и новые проблемы на начальных этапах эксплуатации. Судя по рекламациям клиентов, блок закрепления FK-1150 подвержен уже двум болезням: сервисной ошибке С6610 и замятию J4211.

С6610 – отказ двигателя прижима блока закрепления. Двигатель используется для изменения прижима резинового вала к терморемню в рабочем (печать) и холостом (ожидание) режимах. Работа двигателя, расположенного вне узла закрепления, отслеживается машиной по оптическому датчику прижима, установленному внутри печки.

Диагностика двигателя без нагрузки и с нагрузкой показана в данном видео:

(Видео также доступно на нашем youtube-канале)

Источник

  • Code: 0030
  • Description: FAX PWB system error The FAX process cannot be continued due to the malfunction of the FAX PWB.
  • Remedy: FAX PWB Replace the FAX PWB
  • Code: 0070
  • Description: FAX PWB incompatible detection error In the initial communication with the FAX PWB,
  • Remedy: FAX PWB Replace the FAX PWB. Main/Engine PWB Replace the main/engine PWB.
  • Code: 0100
  • Description: Backup memory device error Outputs an abnormal status from the flash memory.
  • Remedy: Flash memory Replace the main/engine PWB. Main/Engine PWB Replace the main/engine PWB.
  • Code: 0120
  • Description: MAC address data error In case MAC address is invalid data
  • Remedy: Flash memory Replace the main/engine PWB.
  • Code: 0130
  • Description: Backup memory Read/write error Read/write to the NAND memory cannot be executed.
  • Remedy: Flash memory Replace the main/engine PWB. Main/Engine PWB Replace the main/engine PWB.
  • Code: 0140
  • Description: Backup memory data error At power up, the data that was read from the NAND memory has been determined to be a error.
  • Remedy: Flash memory Replace the main/engine PWB.
    Main/Engine PWB Replace the main/engine PWB.
  • Code: 0150
  • Description: EEPROM read/write error (Main/ Engine PWB) Mismatch of reading data from two locations occurs 8 times successively. Mismatch between writing data and reading data occurs 8 times successively.
  • Remedy: EEPROM(YS1) Confirm that the EEPROM has been properly installed and repair if failed.
    Main/Engine PWB Replace the main/engine PWB.
    EEPROM(YS1) Contact the service support.
  • Code: 0160
  • Description: Backup memory data error Illegal data is detected in the EEPROM Counter data checksum does not match in all buffers
  • Remedy: EEPROM(YS1) Check that the EEPROM (YS1) is firmly installed and repair it if failed. Main/Engine PWB Replace the main/engine PWB. EEPROM(YS1) Contact the service support.
  • Code: 0170
  • Description: Billing counting error Checksum error was detected both in the billing counter and IPU backup memory
  • Remedy: Main/Engine PWB Replace the main/engine PWB.
    EEPROM(YS1) Contact the service support.
  • Code: 0180
  • Description: Machine number mismatch When the power is turned on, the machine number does not match between the main and engine side.
  • Remedy: Main/Engine PWB Execute U004 machine number setting
    EEPROM(YS1) Contact the service support.
  • Code: 0190
  • Description: Backup memory device error Unable to read out data from the EEPROM. The above remains at 3 times of retries
  • Remedy: Main/Engine PWB Replace the main/engine PWB.
    EEPROM(YS1) Contact the service support.
  • Code: 0500
  • Description: Drive lock detection by engine firmware The main motor was left rotating when monitoring it in the regular interval (monitored also during the maintenance mode)
  • Remedy: Main/Engine PWB Turn the power switch off and on If not corrected, replace the main/ engine PWB.
  • Code: 0510
  • Description: High voltage remote control error detection It was detected that the high voltage remote signal (synchronized with the feed motor remote) is on while the drum is not driven
  • Remedy: Main/Engine PWB Turn the power switch off and on If not corrected, replace the main/ engine PWB.
  • Code: 0530
  • Description: Backup task error detection The time for the backup task not being in operation is 30s or more
  • Remedy: Main/Engine PWB Turn the power switch off and on If not corrected, replace the main/ engine PWB.
  • Code: 0540
  • Description: Unexpected engine firmware control detection? (Preventing the solenoid from continuously being on) The solenoid was continuously on for the specified time or more
  • Remedy: Main/Engine PWB Turn the power switch off and on If not corrected, replace the main/ engine PWB.
  • Code: 0800
  • Description: Print sequence error The printing sequence jam (JAM010X) occurred twice consecutively.
  • Remedy: Main/Engine PWB Turn the power switch off and on If not corrected, replace the main/ engine PWB.
  • Code: 0830
  • Description: FAX PWB flash program area checksum error The program stored in the flash memory on the FAX PWB is broken and cannot be executed.
  • Remedy: FAX PWB Replace the FAX PWB.
  • Code: 0840
  • Description: RTC error Communication with the RTC has failed The RTC data mismatch such as dead battery
  • Remedy: Battery on the main/engine PWB Check it and repair it if it is faulty.
    Main/Engine PWB Replace the main/engine PWB.
  • Code: 0870
  • Description: FAX PWB large data transmission error DMA transmission failed between the main/engine PWB and FAX PWB
  • Remedy: FAX PWB Reattach the FAX PWB.
    FAX PWB or main/engine PWB Replace the FAX PWB or main/engine PWB.
  • Code: 0920
  • Description: Fax file system error The backup data is not retained for file system abnormality of the flash memory of the FAX PWB.
  • Remedy: FAX PWB Replace the FAX PWB.
  • Code: 0970
  • Description: 24V power down detect The power shutoff was detected by the controller
  • Remedy: Interlock switch Check that the interlock switch is turned on properly by the front cove.
    Low voltage power supply PWB Check if there is defective connection in the connector of the low voltage power supply PWB, and then check the 24V output from the main/engine PWB (YC20-1, 2,3). If not, replace the low voltage power supply PWB.
    Main/Engine PWB Replace the main/engine PWB and check the operation.
  • Code: 1810
  • Description: Communication error with the paper feeder (1st PF) No paper feeder was detected after the paper feeder connection was detected at power-up
  • Remedy: Paper feeder Check the wiring connection status with the main unit, and if necessary, reconnect it.
    PF main PWB 1. Confirm that the wiring connector is firmly connected, and if necessary, connect the connector all the way in. PF main PWB — Main/engine PWB (YC17) 2. If the wiring is disconnected, shortcircuited or has a ground fault, replace the wire. 3. Replace the PF main PWB.
    Main/ Engine PWB 1. Check the engine firmware and upgrade to the latest version if necessary. 2. Replace the main/engine PWB.
  • Code: 1820
  • Description: Communication error with the paper feeder (2nd PF) No paper feeder was detected after the paper feeder connection was detected at power-up
  • Remedy: Paper feeder Check the wiring connection status with the main unit, and if necessary, reconnect it.
    PF main PWB 1. Confirm that the wiring connector is firmly connected, and if necessary, connect the connector all the way in. PF main PWB and Main/engine PWB (YC47) 2. If the wiring is disconnected, shortcircuited or has a ground fault, replace the wire. 3. Replace the PF main PWB.
    Main/ Engine PWB 1. Check the engine firmware and upgrade to the latest version if necessary. 2. Replace the main/engine PWB.
  • Code: 2000
  • Description: Main motor steady-state error After the main motor was stabilized, the ready signal was not detected for consecutive 1s.
  • Remedy: Wire and connector between the main motor and main/engine PWB (YC9) If the connector is not inserted enough, reinsert it. Or check the wire’s continuity and replace the wire if there is no continuity.
    Main motor drive transmission system Check if each roller and gear rotate smoothly. Apply grease to the bushings and gears if they are faulty. Check each gear if it is damaged and replace it if there is damage.
    Main motor Replace the main motor.
    Main/Engine PWB Replace the main/engine PWB.
  • Code: 2010
  • Description: Main motor start-up error The ready signal was not detected when passing 2s after the main motor is started up.
  • Remedy: Wire and connector between the main motor and main/engine PWB (YC9) If the connector is not inserted enough, reinsert it. Or check the wire’s continuity and replace the wire if there is no continuity.
    Main motor drive transmission system Check if each roller and gear rotate smoothly. Apply grease to the bushings and gears if they are faulty. Check each gear if it is damaged and replace it if there is damage.
    Main motor Replace the main motor.
    Main/Engine PWB Replace the main/engine PWB.
  • Code: 2600
  • Description: PF conveying motor error (Paper feeder) The ready signal is not detected within 2s after the PF conveying motor of the cassette 2 turns on.
  • Remedy: Connection of the wire and connector PF conveying motor — PF main PWB If the connector is not inserted enough, reinsert it. Or check the wire’s continuity and replace the wire if there is no continuity.
    PF conveying motor drive transmission system Check if each roller and gear rotate smoothly. Apply grease to the bushings and gears if they are faulty. Check each gear if it is damaged and replace it if there is damage.
    PF conveying motor Replace the PF conveying motor.
  • Code: 2610
  • Description: PF conveying motor error (Paper feeder) The ready signal is not detected within 2s after the PF conveying motor of the cassette 3 turns on.
  • Remedy: Connection of the wire and connector PF conveying motor — PF main PWB If the connector is not inserted enough, reinsert it. Or check the wire’s continuity and replace the wire if there is no continuity.
    PF conveying motor drive transmission system Check if each roller and gear rotate smoothly. Apply grease to the bushings and gears if they are faulty. Check each gear if it is damaged and replace it if there is damage.
    PF conveying motor Replace the PF conveying motor.
  • Code: 3100
  • Description: Carriage error 1) While the HP sensor is interrupted at the initial drive, it is not released when driven by 66.1mm toward the scanning direction 2) During the initial drive while the HP sensor is released, the HP sensor is not interrupted when driving it by 379.5mm toward the return direction
  • Remedy: Scanner motor 1. Move the scanner manually to check if there is too much load. 2. Check that the scanner drive belt is not disengaged. 3. Confirm that the wiring connector is firmly connected, and if necessary, connect the connector all the way in. Scanner motor — Main/engine PWB (YC31) 4. If the wiring is disconnected, shortcircuited or has a ground fault, replace the wire. 5. Replace the scanner motor.
    Home position sensor 1. Check that the sensor is correctly positioned. 2. Confirm that the wiring connector is firmly connected, Insert the connector all the way in. Home position sensor — Main/engine PWB (YC17) 3. Replace the home position sensor.
    CIS Replace the scanner carriage and execute U411.
    Main/ Engine PWB Replace the main/engine PWB.
  • Code: 3200
  • Description: CIS lamp error The white reference data obtained when the lamp is turned on at the time of initialization is lower than the rated value.
  • Remedy: CIS Replace the scanner carriage and execute U411.
    Main/ Engine PWB Replace the main/engine PWB.
  • Code: 3210
  • Description: DP CIS lamp error The white reference data obtained when the lamp is turned on at the time of initialization is lower than the rated value. (40 ppm model only)
  • Remedy: DP CIS 1. Confirm that the wiring connector is firmly connected, and if necessary, connect the connector all the way in. DPCIS — Main/Engine PWB(YC509) 2. Replace DPCIS and execute U411.
  • Code: 3300
  • Description: CIS AGC error An error was detected when processing the front side AGC
  • Remedy: CIS 1. Confirm that the wiring connector is firmly connected, and if necessary, connect the connector all the way in. CIS — Main/Engine PWB (YC506) 2. If the wiring is disconnected, shortcircuited or has a ground fault, replace the wire. 3. Replace the scanner carriage and execute U411
    Main/Engine PWB Replace the main/engine PWB.
  • Code: 3310
  • Description: DP CIS AGC error An error was detected when processing the back side AGC (40 ppm model only)
  • Remedy: DP CIS 1. Confirm that the wiring connector is firmly connected, and if necessary, connect the connector all the way in. DPCIS — Main/Engine PWB(YC509) 2. Replace DPCIS and execute U411.
    Main/Engine PWB Replace the main/engine PWB.
  • Code: 3500
  • Description: Scanner — ASIC communication error A communication error is detected during communication. (Read-back values are different.)
  • Remedy: CIS 1. Confirm that the wiring connector is firmly connected, and if necessary, connect the connector all the way in. CIS — Main/Engine PWB (YC506) 2. If the wiring is disconnected, shortcircuited or has a ground fault, replace the wire. 3. Replace the image scanner carriage and execute U411.
    Main/Engine PWB Replace the main/engine PWB.
  • Code: 4000
  • Description: Polygon motor initial error (LSU) The polygon motor ready signal is not detected when passing 10s after starting up the polygon motor
  • Remedy: Laser scanner unit (LSU) 1. Confirm that the wiring connector is firmly connected, and if necessary, connect the connector all the way in. Polygon motor — Main/engine PWB (YC3) If the wiring is disconnected, short-circuited or has a ground fault, replace the wire. 2. Replace the LSU.
    Main/Engine PWB 1. Check the engine firmware and upgrade to the latest version if necessary. 2. Replace the main/engine PWB.
  • Code: 4010
  • Description: Polygon motor steady-state error (LSU) The polygon motor ready signal is not for consecutive 1s after the polygon motor is stabilized
  • Remedy: Laser scanner unit (LSU) 1. Confirm that the wiring connector is firmly connected, and if necessary, connect the connector all the way in. Polygon motor — Main/engine PWB (YC3) If the wiring is disconnected, short-circuited or has a ground fault, replace the wire. 2. Replace the LSU.
    Main/Engine PWB 1. Check the engine firmware and upgrade to the latest version if necessary. 2. Replace the main/engine PWB.
  • Code: 4201
  • Description: BD steady-state error (LSU) BD was not obtained during the steady rotation
  • Remedy: Laser scanner unit (LSU) 1. Confirm that the wiring connector is firmly connected, and if necessary, connect the connector all the way in. LSU — Main/Engine PWB (YC505) 2. If the wiring is disconnected, shortcircuited or has a ground fault, replace the wire. 3. Replace the LSU.
    Main/Engine PWB Replace the main/engine PWB.
  • Code: 6000
  • Description: Broken fuser heater wire (main) During warm-up, the temperature detected by the thermopile does not reach 100°C/212 °F when turning the heater on for consecutive 10s During warm up, the temperature detected by the thermopile does not reach the ready temperature when passing 30s after reaching 60°C/ 212°F.
  • Remedy: Fuser unit 1. Make sure there is no paper jam. 2. Confirm that the wiring connector is firmly connected, and if necessary, connect the connector all the way in. Fuser unit — Main/Engine PWB(YC19) 3. If the wiring is disconnected, shortcircuited or has a ground fault, replace the wire. 4. If the fuser heater is not turned on (broken thermostat wire), replace the fuser unit.
    Low voltage power supply PWB 1. Confirm that the wiring connector is firmly connected, and if necessary, connect the connector all the way in. Heater — Low voltage power supply PWB (YC102) Low voltage power supply PWB — Main/ Engine PWB(YC20) 2. Replace the low voltage power supply PWB.
    Main/Engine PWB Replace the main/engine PWB.
  • Code: 6020
  • Description: Fuser thermopile high temperature error (main) During drive, the thermopile detected 200C/392 °F for 5s The temperature detected by the thermopile rose 18C/65 °F or more when passing 1s or more after the drive is stopped Detected temperature at that time is 200C/392 °or more
  • Remedy: Thermopile 1. Reconnect the wire connector Replace the wire if there is no continuity. Thermopile — Main/engine PWB (YC2) 2. Check how the thermopile is attached. If not attached to the holder, correct it 3. Replace the thermopile if not repaired
    Fuser unit 1. Make sure there is no paper jam. 2. If the fuser heater is not turned on (broken thermostat wire), replace the fuser unit.
    Low voltage power supply PWB 1. Confirm that the wiring connector is firmly connected, and if necessary, connect the connector all the way in. Low voltage power supply PWB — Main/ Engine PWB(YC20) 2. Replace the low voltage power supply PWB.
    Main/Engine PWB Replace the main/engine PWB.
  • Code: 6030
  • Description: Broken fuser thermopile wire (main) The thermopile detected an abnormal value
  • Remedy: Thermopile 1. Reconnect the wire connector Replace the wire if there is no continuity. Thermopile — Main/engine PWB (YC2) 2. Replace the thermopile if not repaired
    Main/Engine PWB Replace the main/engine PWB.
  • Code: 6050
  • Description: Fuser thermopile low temperature error (main) During printing, the temperature detected by the thermopile is less than 100C/212°F for consecutive 3s
  • Remedy: Power supply voltage 1. Check no voltage drop exceeding 10% of the rated during printing. 2. If the power is overloaded, change the AC outlet that supplies power.
    Thermopile 1. Reconnect the wire connector Replace the wire if there is no continuity. Thermopile — Main/engine PWB (YC2) 2. Check how the thermopile is attached. If not attached to the holder, correct it 3. Replace the thermopile if not repaired
    Fuser unit 1. Make sure there is no paper jam. 2. Confirm that the wiring connector is firmly connected, and if necessary, connect the connector all the way in. Fuser unit — Main/Engine PWB(YC19) 3. If the wiring is disconnected, shortcircuited or has a ground fault, replace the wire. 4. If the fuser heater is not turned on (broken thermostat wire), replace the fuser unit.
    Low voltage power supply PWB 1. Confirm that the wiring connector is firmly connected, and if necessary, connect the connector all the way in. Heater — Low voltage power supply PWB (YC102) Low voltage power supply PWB — Main/ Engine PWB(YC20) 2. Replace the low voltage power supply PWB.
    Main/Engine PWB Replace the main/engine PWB.
  • Code: 6200
  • Description: Fuser heater error (sub) During warm-up, the temperature detected by the thermistor does not reach 60C/212.0 °F when turning the heater on for consecutive 30s. During warm-up, the temperature detected by the thermistor does not reach the ready temperature when passing 20s after it reaches 60C/ 212°F.
  • Remedy: Thermopile 1. Reconnect the wire connector Replace the wire if there is no continuity. Thermopile — Main/engine PWB (YC2) 2. Replace the thermopile if not repaired
    Fuser unit 1. Make sure there is no paper jam. 2. Confirm that the wiring connector is firmly connected, and if necessary, connect the connector all the way in. Fuser unit — Main/Engine PWB(YC19) 3. If the wiring is disconnected, shortcircuited or has a ground fault, replace the wire. 4. If the fuser heater is not turned on (broken thermostat wire), replace the fuser unit.
    Low voltage power supply PWB 1. Confirm that the wiring connector is firmly connected, and if necessary, connect the connector all the way in. Heater — Low voltage power supply PWB (YC102) Low voltage power supply PWB — Main/ Engine PWB(YC20) 2. Replace the low voltage power supply PWB.
    Main/Engine PWB Replace the main/engine PWB.
  • Code: 6220
  • Description: Fuser heater high temperature error (sub) The temperature detected by the thermopile is 240°C/464 °F while the drive is stopped The temperature detected by the thermopile is 255°C/491 °F during drive
  • Remedy: Thermopile 1. Reconnect the wire connector Replace the wire if there is no continuity. Thermopile — Main/engine PWB (YC2) 2. Check how the thermopile is attached. If not attached to the holder, correct it 3. Replace the thermopile if not repaired
    Fuser unit 1. Make sure there is no paper jam. 2. Confirm that the wiring connector is firmly connected, and if necessary, connect the connector all the way in. Fuser unit — Main/Engine PWB(YC19) 3. If the wiring is disconnected, shortcircuited or has a ground fault, replace the wire. 4. Replace the fuser unit.
    Low voltage power supply PWB 1. Confirm that the wiring connector is firmly connected, and if necessary, connect the connector all the way in. Low voltage power supply PWB — Main/ Engine PWB(YC20) 2. Replace the low voltage power supply PWB.
    Main/Engine PWB Replace the main/engine PWB.
  • Code: 6230
  • Description: Fuser thermistor wire break (sub) The thermistor’s AD value was abnormal
  • Remedy: Fuser unit 1. Confirm that the wiring connector is firmly connected, and if necessary, connect the connector all the way in. Fuser unit — Main/Engine PWB(YC19) 2. If the wiring is disconnected, shortcircuited or has a ground fault, replace the wire. 3. If the fuser heater is not turned on (broken thermostat wire), replace the fuser unit.
    Main/Engine PWB Replace the main/engine PWB.
  • Code: 6250
  • Description: Fuser heater low temperature error (sub) During printing, the temperature detected by the thermistor is less than 60°C/140°F for consecutive 3s
  • Remedy: Thermopile 1. Reconnect the wire connector Replace the wire if there is no continuity. Thermopile — Main/engine PWB (YC2) 2. Check how the thermopile is attached. If not attached to the holder, correct it 3. Replace the thermopile if not repaired
    Fuser unit 1. Make sure there is no paper jam. 2. Confirm that the wiring connector is firmly connected, and if necessary, connect the connector all the way in. Fuser unit — Main/Engine PWB(YC19) 3. If the wiring is disconnected, shortcircuited or has a ground fault, replace the wire. 4. Replace the fuser unit.
    Low voltage power supply PWB 1. Confirm that the wiring connector is firmly connected, and if necessary, connect the connector all the way in. Heater — Low voltage power supply PWB (YC102) Low voltage power supply PWB — Main/ Engine PWB(YC20) 2. Replace the low voltage power supply PWB.
    Main/Engine PWB Replace the main/engine PWB.
  • Code: 6400
  • Description: Zero-cross signal error During the heater turned on, the zero-cross signal disappears for consecutive 1s
  • Remedy: Low voltage power supply PWB Replace the low voltage power supply PWB.
    Main/Engine PWB Replace the main/engine PWB.
  • Code: 6600
  • Description: Fuser rotation error The fuser roller rotation detection is not input for consecutive 2s while the motor’s steady signal is input
  • Remedy: Fuser unit 1. Make sure there is no paper jam. 2. Confirm that the wiring connector is firmly connected, and if necessary, connect the connector all the way in. Fuser unit — Main/Engine PWB(YC19) 3. If the wiring is disconnected, shortcircuited or has a ground fault, replace the wire. 4. Replace the fuser unit.
    Main/Engine PWB Replace the main/engine PWB.
  • Code: 6610
  • Description: The fuser pressure release error The fuser pressure change is not complete within 10s after the instruction
  • Remedy: Fuser unit 1. Make sure there is no paper jam. 2. Confirm that the wiring connector is firmly connected, and if necessary, connect the connector all the way in. Fuser unit — Main/engine PWB (YC19) 3. If the wiring is disconnected, shortcircuited or has a ground fault, replace the wire. 4. Replace the fuser unit.
    Fuser pressure release error 1. Reverse-rotate the fuser gear manually to check if the fuser pressure can be released. 2. When releasing the pressure, check the fuser pressure release sensor is interrupted by the actuator Reattach it if the light is not interrupted 3. Reconnect the wire connector Replace the wire if there is no continuity. Fuser pressure release sensor — Main/ engine PWB (YC19) Fuser pressure release motor — Main/ engine PWB (YC1) 4. Replace the fuser pressure release motor.
    Main/Engine PWB Replace the main/engine PWB.
  • Code: 6650
  • Description: Fuser thermopile EEPROM error 1. The thermopile EEPROM is not accessed 2. No response from the device at read was detected five time consecutively Data read at two points was unmatched eight times consecutively 3. Thermopile data checksum error
  • Remedy: Thermopile 1. Reconnect the wire connector Replace the wire if there is no continuity. 2. Thermopile — Main/engine PWB (YC2) 3. Replace the thermopile if not repaired
    Main/Engine PWB Replace the main/engine PWB.
  • Code: 7220
  • Description: Broken in-machine thermistor wire The sensor input sampling value is greater than the reference value.
  • Remedy: In-machine temperature sensor 1. Confirm that the wiring connector is firmly connected, Insert the connector all the way in. In-machine temperature sensor — Main/engine PWB (YC1) 2. If the wiring is disconnected, shortcircuited or has a ground fault, replace the wire. Replace the in-machine temperature sensor PWB.
    Main/Engine PWB Replace the main/engine PWB.
  • Code: 7800
  • Description: Broken outer thermistor wire The sensor input sampling value is abnormal. (After detecting an error, it is controlled at 23C/77 °F and 50%RH)
  • Remedy: Temperature and humidity Sensor 1. Confirm that the wiring connector is firmly connected, and if necessary, connect the connector all the way in. Temperature and humidity sensor — Main/engine PWB (YC2) 2. If the wiring is disconnected, shortcircuited or has a ground fault, replace the wire. 3. Replace the Temperature and humidity sensor PWB.
    Main/Engine PWB Replace the main/engine PWB.
  • Code: 7990
  • Description: Waste toner full The waste toner sensor detected the waste toner reservoir in the drum unit is full
  • Remedy: Drum unit Turn the power switch off and on Replace the drum unit if not repaired.
    Waste toner sensor Replace the waste toner sensor.
    Main/Engine PWB Replace the main/engine PWB.
  • Code: F000
  • Description: Communication error between Main/Engine PWB — Operation panel PWB
  • Remedy: Connection of the wires and connectors between the main/engine PWB — the operation panel PWB. If the connector is not inserted enough, reinsert it. Or check the wire’s continuity and replace the wire if there is no continuity.
    Operation panel PWB Replace the operation panel PWB. (TSI: see page 4-138, LCD: see page 4- 141)
    Main/Engine PWB Replace the main/engine PWB.
  • Code: F010
  • Description: Main/Engine PWB Checksum error
  • Remedy: Main/Engine PWB Unplug the power cord from the wall outlet, and wait five seconds. Then plug in the power cord and then turn on the power switch. If not corrected, replace the main/ engine PWB.
  • Code: F020
  • Description: Main/engine PWB RAM checksum error
  • Remedy: Main/engine PWB memory (RAM) Turn the power switch off and on If not corrected, replace the main/ engine PWB.
    Expansion memory (DIMM) Replace the expansion memory (DIMM)
  • Code: F040
  • Description: Main/engine PWB engine communication error
  • Remedy: Main/Engine PWB Turn the power switch off and on If not repaired, replace the EEPROM on the main/engine PWB or main/engine PWB.
  • Code: F041
  • Description: Main/engine PWB — Scanner PWB communication error
  • Remedy: Main/Engine PWB Turn the power switch off and on If not corrected, replace the main/ engine PWB.
  • Code: F050
  • Description: Main/engine PWB engine checksum error
  • Remedy: Main/Engine PWB Download the engine firmware again (TSI: see page 4-138,LCD: see page 4- 141)
    Main/Engine PWB Turn the power switch off and on If not repaired, replace the EEPROM on the main/engine PWB or main/engine PWB.
  • Code: F051
  • Description: No scan engine main program
  • Remedy: Main/Engine PWB Turn the power switch off and on If not corrected, replace the main/ engine PWB.
  • Code: F12X
  • Description: Abnormality detecting in a Scan control section
  • Remedy: (1) Check the harness between Scan/DP<=>Main/Engine PWBs, and the connection state of a connector, and perform an operation check. (2) U021 Controller backup initialization is carried out and an operation check is performed. (3) Exchange a Scan/DP board and perform an operation check. (4) Exchange a Main/Engine PWB and perform an operation check. (5) Get USBLOG and contact service headquarters.
  • Code: F14X
  • Description: Abnormality detecting in a FAX control part
  • Remedy: (1) Check the harness between FAX<=>Main/Engine PWBs, and the connection state of a connector, and perform an operation check. (2) U021 Controller backup initialization is carried out and an operation check is performed. (3) Perform a deed operation check for DIMM Clear by U671. * Notes(Since it disappears when received data remain, cautions are required.) (4) Exchange a FAX board and perform an operation check. (5) Exchange a Main/Engine PWB and perform an operation check. (6) Get USBLOG and contact service headquarters.
  • Code: F15X
  • Description: Abnormality detecting in an authentication device control section
  • Remedy: (1) Check the harness between authentication device <=>Main/ Engine PWBs, and the connection situation of a connector, and perform an operation check. (2) Carry out U021 Main backup initialization and perform an operation check. (3) Exchange a Main/Engine PWB and perform an operation check. (4) Get USBLOG and contact service headquarters.
  • Code: F18X
  • Description: Abnormality detecting in a Video control section
  • Remedy: (1) Check the harness between Engine<=>Main/Engine PWBs, and the connection state of a connector, and perform an operation check. (2) U021 Controller backup initialization is carried out and an operation check is performed. (3) Exchange a Main/Engine PWB and perform an operation check. (4) Get USBLOG and contact service headquarters.
  • Code: F1DX
  • Description: Abnormality detecting of the image memory Management Department
  • Remedy: (1) Carry out U021 Main backup initialization and perform an operation check. (2) Exchange a Main/Engine PWB and perform an operation check. (3) Get USBLOG and contact service headquarters.
  • Code: F21X, F22X, F23X
  • Description: Abnormality detecting in an image-processing part
  • Remedy: (1) Check contact of a DDR memory and perform an operation check. (2) Carry out U021 Main backup initialization and perform an operation check. (3) Exchange a Main/Engine PWB and perform an operation check. (4) Get USBLOG and contact service headquarters.
  • Code: F24X
  • Description: Abnormality detecting in the system Management Department
  • Remedy: (1) Check contact of a DDR memory and perform an operation check. (2) Carry out U021 Main backup initialization and perform an operation check. (3) Exchange a Main/Engine PWB and perform an operation check. (4) Get USBLOG and contact service headquarters.
  • Code: F25X
  • Description: Abnormality detecting in a network management department
  • Remedy: (1) Carry out U021 Main backup initialization and perform an operation check. (2) Exchange a Main/Engine PWB and perform an operation check. (3) Get USBLOG and packet capture and contact service headquarters.
  • Code: F26X … F2AX
  • Description: Abnormality detecting in the system Management Department
  • Remedy: (1) Carry out U021 Main backup initialization and perform an operation check. (2) Exchange a Main/Engine PWB and perform an operation check. (3) Get USBLOG and contact service headquarters.
  • Code: F2BX … F32X
  • Description: Abnormality detecting in a network control part
  • Remedy: (1) Carry out U021 Main backup initialization and perform an operation check. (2) Exchange a Main/Engine PWB and perform an operation check. (3) Get USBLOG and contact service headquarters.(Depending on an analysis result, it is packet capture acquisition)
  • Code: F33X
  • Description: Abnormality detecting in the Scan Management Department
  • Remedy: (1) Check the harness between Scan/DP<=>Main/Engine PWBs, and the connection state of a connector, and perform an operation check. (2) U021 Controller backup initialization is carried out and an operation check is performed. (3) Exchange a Scan/DP board and perform an operation check. (4) Exchange a Main/Engine PWB and perform an operation check. (5) Get USBLOG and contact service headquarters.
  • Code: F34X
  • Description: Abnormality detecting in the Panel Management Department
  • Remedy: (1) Check the harness between Panel<=>Main/Engine PWBs, and the connection state of a connector, and perform an operation check. * Notes (2) U021 Controller backup initialization is carried out and an operation check is performed. (3) Exchange a Panel board and perform an operation check. (4) Exchange a Main/Engine PWB and perform an operation check. (5) Get USBLOG and contact service headquarters.
  • Code: F35X
  • Description: Abnormality detecting in the printing controlling Management Department
  • Remedy: (1) Carry out U021 Main backup initialization and perform an operation check. (2) Exchange a Main/Engine PWB and perform an operation check. (3) Get USBLOG and contact service headquarters.
  • Code: F37X
  • Description: Abnormality detecting in the FAX Management Department
  • Remedy: (1) Carry out U021 Main backup initialization and perform an operation check. (2) Exchange a Main/Engine PWB and perform an operation check. (3) Get USBLOG and contact service headquarters.
  • Code: F38X
  • Description: Abnormality detecting in the authentication authorized Management Department
  • Remedy: (1) Carry out U021 Main backup initialization and perform an operation check. (2) Exchange a Main/Engine PWB and perform an operation check. (3) Get USBLOG and contact service headquarters.
  • Code: F3AX … F45X
  • Description: Abnormality detecting in the Entity Management Department
  • Remedy: (1) Carry out U021 Main backup initialization and perform an operation check. (2) Exchange a Main/Engine PWB and perform an operation check. (3) Get USBLOG and contact service headquarters.
  • Code: F46X
  • Description: Abnormality detecting of a printer rendering part
  • Remedy: (1) Exchange a Main/Engine PWB and perform an operation check. (2) the acquisition wish of USBLOG — carry out (Depending on the (2) case, it is print capture data acquisition)
  • Code: F47X, F48X, F49X
  • Description: Abnormality detecting of an image editing processing part
  • Remedy: (1) Carry out U021 Main backup initialization and perform an operation check. (2) Exchange a Main/Engine PWB and perform an operation check. (3) Get USBLOG and contact service headquarters.
  • Code: F4DX, F4EX
  • Description: Abnormality detecting in the Entity Management Department
  • Remedy: (1) Carry out U021 Main backup initialization and perform an operation check. (2) Exchange a Main/Engine PWB and perform an operation check. (3) Get USBLOG and contact service headquarters.
  • Code: F4FX
  • Description: Abnormality detecting in the JOB Management Department
  • Remedy: (1) Carry out U021 Main backup initialization and perform an operation check. (2) Exchange a Main/Engine PWB and perform an operation check. (3) Get USBLOG and contact service headquarters.
  • Code: F50X
  • Description: Abnormality detecting in the FAX Management Department
  • Remedy: (1) Carry out U021 Main backup initialization and perform an operation check. (2) Exchange a Main/Engine PWB and perform an operation check. (3) Get USBLOG and contact service headquarters.
  • Code: F51X … F57X
  • Description: Abnormality detecting in a JOB execution part
  • Remedy: (1) Carry out U021 Main backup initialization and perform an operation check. (2) Exchange a Main/Engine PWB and perform an operation check. (3) Get USBLOG and contact service headquarters.
  • Code: F58X … F5EX
  • Description: Abnormality detecting in the various-services Management Department
  • Remedy: (1) Carry out U021 Main backup initialization and perform an operation check. (2) Exchange a Main/Engine PWB and perform an operation check. (3) Get USBLOG and contact service headquarters.
  • Code: F5FX
  • Description: Abnormality detecting in a service execution part
  • Remedy: (1) Carry out U021 Main backup initialization and perform an operation check. (2) Exchange a Main/Engine PWB and perform an operation check. (3) Get USBLOG and contact service headquarters.
  • Code: F62X
  • Description: Abnormality detecting in a service execution part
  • Remedy: (1) Carry out U021 Main backup initialization and perform an operation check. (2) Exchange a Main/Engine PWB and perform an operation check. (3) Get USBLOG and contact service headquarters.
  • Code: F63X
  • Description: Abnormality detecting in a device control section
  • Remedy: (1) Carry out U021 Main backup initialization and perform an operation check. (2) Exchange a Main/Engine PWB and perform an operation check. (3) Get USBLOG and contact service headquarters.
  • Code: F69X … F6CX
  • Description: Abnormality detecting in a HyPAS-E part
  • Remedy: (1) Carry out U021 Main backup initialization and perform an operation check. (2) Exchange a Main/Engine PWB and perform an operation check. (3) Get USBLOG and contact service headquarters.

Понравилась статья? Поделить с друзьями:

Читайте также:

  • Kyocera m2040dn ошибка 4211
  • Kyocera m2040dn ошибка 1102
  • Kyocera m2040dn xps print error
  • Kyocera m2040dn f000 error
  • Kyocera m2040dn error f245

  • 0 0 голоса
    Рейтинг статьи
    Подписаться
    Уведомить о
    guest

    0 комментариев
    Старые
    Новые Популярные
    Межтекстовые Отзывы
    Посмотреть все комментарии