Kyocera p6021cdn ошибка 7402

В машинах Kyocera P6021cdn, P6026cdn, M6026cdn/cidn, M6526cdn/cidn, FSC5150/5250/5350 и многих других довольно часто приходится сталкиваться с ошибкам C7401, C7402, C7403, C7404. Описание этих ошибок в сервисной документации такое: "Developing u...

Чем мы можем вам сегодня помочь?



Изменено: Чт, 12 Июл, 2018 at 3:35 PM


В машинах Kyocera P6021cdn, P6026cdn, M6026cdn/cidn, M6526cdn/cidn, FSC5150/5250/5350 и многих других довольно часто приходится сталкиваться с ошибкам C7401, C7402, C7403, C7404.

Описание этих ошибок в сервисной документации такое: «Developing unit non-installing error».  Суть ошибок — машина не «видит» сигнала с датчика концентрации тонера в блоке проявки (7401 –Black, 7402 – Cyan, 7403 – Magenta, 7404 – Yellow). 

Т.е. показания датчика выходят за допустимый диапазон, что может быть вызвано чрезмерно низкой концентрацией тонера в девелопере или недостаточным количеством девелопера в блоке проявки. Предлагаемый сервисной документацией способ устранения проблемы обычно заканчивается весьма дорогим пунктом — заменой блоков проявки целиком.

Частые причины появления проблемы – использование «не очень совместимого» тонера или использование машины не по своему назначению. Машины предназначены для офисной печати в нормальных условиях, и не очень хорошо справляются с печатью при высоком или низком заполнении тонером напечатанных страниц, а также в условиях высокой или низкой влажности воздуха.

Рекомендуемый нами метод лечения, опробованный на нескольких машинах:

  • Для очистки совести проверить разъемы и провода на пути от датчиков концентрации тонера до платы.
  • Проверить систему подачи тонера – часто ломаются шестерни шнеков подачи тонера, которые находятся в блоке ленты переноса.

  • Опустить магнит в бункер отработки, чтобы выяснить имел ли место «вынос» девелопера в отработку.
  • При отсутствии девелопера в бункере отработки вручную добавить и распределить тонер в блок проявки. Добавлять через входное отверстие блока проявки, распределять вращением валов блока проявки за шестерню. Обычно для вывода машины из состояния ошибки достаточно добавить 3-5 г тонера и вращать вручную шестерню блока проявки 2-3 минуты.

  • При присутствии девелопера в бункере отработки сначала вручную добавить совместимый носитель в блок проявки, затем тонер. Добавлять через входное отверстие блока проявки, распределять вращением валов блока проявки за шестерню. Примерное количество носителя, которое нужно добавить, можно выяснить сравнением веса проблемного и «живого» блока проявки.
  • После входа машины на готовность запустить из меню машины процедуру DEV-CLN (1 раз, чтобы не заклинить систему вывода отработки!) затем калибровку цвета. Это позволит машине довести концентрацию тонера до установленных значений.

Профилактика:

  • Обновление прошивки. Kyocera иногда вносит в прошивки коррекции, связанные с алгоритмом подкачки тонера. 
  • Использование «нормального» тонера.
  • Беседа с клиентом о том, что офисная машина предназначена для печати офисных документов, а не для оперативной полиграфии и т.п.

Была ли эта статья полезной?
Да

Нет

Отправить отзыв

К сожалению, мы не смогли помочь вам в разрешении проблемы. Ваш отзыв позволит нам улучшить эту статью.

Статьи по теме

    Модератор: vetal






    Прилепить пост

    Сообщение Усатый Полосатый » Ср авг 29, 2018 6:31 pm

    Изменить размер шрифта ↓ВернутьИзменить размер шрифта ↑Я купил в рамисе девелоп, 4 флакона, эти самые 110гр девелопера. Тонера насыпал чуть больше, ок 20-25 гр. К слову, вес снаряженной проявки по извлечению составлял ок 670 гр, а вес сухой, после чистки, составил 480 гр, т.е., больше весом, чем засыпаемая мной смесь.

    Кто чего то хочет — ищет пути и возможности !!! Кому ничего не надо — только причины ….

    Аватар пользователя

    Усатый Полосатый

      

    Вместо работы сидит на форуме

    • Не в сети
    • ICQ
    • Персональный альбом










    • Kyocera FS-1120d индикатор «Нет бумаги»

      vs-dos в форуме Принтеры, МФУ, факсы, копиры формата A4

      11
      14632

      СТРОНЦИЙ
      Перейти к последнему сообщению
      Вт ноя 02, 2021 2:24 pm
    • [SCANNER ERROR] Lamp Error Kyocera FS-1016

      мастерчип в форуме Принтеры, МФУ, факсы, копиры формата A4

      3
      6456

      Усатый Полосатый
      Перейти к последнему сообщению
      Вс окт 28, 2018 11:08 pm
    • Kyocera 1035 «бледная» печать

      srMax в форуме Принтеры, МФУ, факсы, копиры формата A4

      2
      13592

      srMax
      Перейти к последнему сообщению
      Пт янв 23, 2015 2:49 pm
    • Taskalfa 180 ошибка «Е» и «Встряхните картр. с тонером»

      manik.76 в форуме Принтеры, МФУ, копиры формата A3

      3
      9234

      dviz
      Перейти к последнему сообщению
      Пн фев 20, 2017 1:35 pm
    • Kyocera Ecosys M2635dn «поворот» изображения

      Искатель в форуме Принтеры, МФУ, факсы, копиры формата A4

      10
      5777

      MatrixAgent
      Перейти к последнему сообщению
      Ср апр 08, 2020 5:18 am

    Вернуться в Принтеры, МФУ, факсы, копиры формата A4

    Кто сейчас на форуме

    Сейчас этот форум просматривают: нет зарегистрированных пользователей и гости: 57

    Расходочка.рф

    • Главная
    • Статьи
    • Ошибки 7401, 7402, 7403, 7404 в машинах Kyocera Ecosys P6021cdn, P6026cdn, M6026cdn, M6526cdn и других

    В машинах Kyocera P6021cdn, P6026cdn, M6026cdn/cidn, M6526cdn/cidn, FSC5150/5250/5350 и многих других довольно часто приходится сталкиваться с ошибкам C7401, C7402, C7403, C7404.

    Описание этих ошибок в сервисной документации такое: «Developing unit non-installing error».  Суть ошибок — машина не «видит» сигнала с датчика концентрации тонера в блоке проявки (7401 –Black, 7402 – Cyan, 7403 – Magenta, 7404 – Yellow). 

    Т.е. показания датчика выходят за допустимый диапазон, что может быть вызвано чрезмерно низкой концентрацией тонера в девелопере или недостаточным количеством девелопера в блоке проявки. Предлагаемый сервисной документацией способ устранения проблемы обычно заканчивается весьма дорогим пунктом — заменой блоков проявки целиком.

    Частые причины появления проблемы – использование «не очень совместимого» тонера или использование машины не по своему назначению. Машины предназначены для офисной печати в нормальных условиях, и не очень хорошо справляются с печатью при высоком или низком заполнении тонером напечатанных страниц, а также в условиях высокой или низкой влажности воздуха.

    Рекомендуемый нами метод лечения, опробованный на нескольких машинах:

    • Для очистки совести проверить разъемы и провода на пути от датчиков концентрации тонера до платы.
    • Проверить систему подачи тонера – часто ломаются шестерни шнеков подачи тонера, которые находятся в блоке ленты переноса.

    • Опустить магнит в бункер отработки, чтобы выяснить имел ли место «вынос» девелопера в отработку.
    • При отсутствии девелопера в бункере отработки вручную добавить и распределить тонер в блок проявки. Добавлять через входное отверстие блока проявки, распределять вращением валов блока проявки за шестерню. Обычно для вывода машины из состояния ошибки достаточно добавить 3-5 г тонера и вращать вручную шестерню блока проявки 2-3 минуты.

    • При присутствии девелопера в бункере отработки сначала вручную добавить совместимый носитель в блок проявки, затем тонер. Добавлять через входное отверстие блока проявки, распределять вращением валов блока проявки за шестерню. Примерное количество носителя, которое нужно добавить, можно выяснить сравнением веса проблемного и «живого» блока проявки.
    • После входа машины на готовность запустить из меню машины процедуру DEV-CLN (1 раз, чтобы не заклинить систему вывода отработки!) затем калибровку цвета. Это позволит машине довести концентрацию тонера до установленных значений.

    Профилактика:

    • Обновление прошивки. Kyocera иногда вносит в прошивки коррекции, связанные с алгоритмом подкачки тонера. 
    • Использование «нормального» тонера.
    • Беседа с клиентом о том, что офисная машина предназначена для печати офисных документов, а не для оперативной полиграфии и т.п.

    12.07.2018

    Содержание

    1. Чем мы можем вам сегодня помочь?
    2. Ошибки 7401, 7402, 7403, 7404 в цветных машинах Kyocera
    3. Ошибки у принтеров Kyocera FS-1020MFP, FS-1025MFP, FS-1030MFP, FS-1120MFP, FS-1125MFP, FS-1220MFP и прочих моделей? Советы по сбросу и устранению!
    4. Сброс ошибок у принтеров Kyocera своими руками
    5. Устранение ошибок у принтеров Kyocera в сервисном центре

    Чем мы можем вам сегодня помочь?

    Ошибки 7401, 7402, 7403, 7404 в цветных машинах Kyocera

    Изменено: Чт, 12 Июл, 2018 at 3:35 PM

    В машинах Kyocera P6021cdn, P6026cdn, M6026cdn/cidn, M6526cdn/cidn, FSC5150/5250/5350 и многих других довольно часто приходится сталкиваться с ошибкам C7401, C7402, C7403, C7404.

    Описание этих ошибок в сервисной документации такое: «Developing unit non-installing error». Суть ошибок — машина не «видит» сигнала с датчика концентрации тонера в блоке проявки (7401 –Black, 7402 – Cyan, 7403 – Magenta, 7404 – Yellow).

    Т.е. показания датчика выходят за допустимый диапазон, что может быть вызвано чрезмерно низкой концентрацией тонера в девелопере или недостаточным количеством девелопера в блоке проявки. Предлагаемый сервисной документацией способ устранения проблемы обычно заканчивается весьма дорогим пунктом — заменой блоков проявки целиком.

    Частые причины появления проблемы – использование «не очень совместимого» тонера или использование машины не по своему назначению. Машины предназначены для офисной печати в нормальных условиях, и не очень хорошо справляются с печатью при высоком или низком заполнении тонером напечатанных страниц, а также в условиях высокой или низкой влажности воздуха.

    Рекомендуемый нами метод лечения, опробованный на нескольких машинах:

    • Для очистки совести проверить разъемы и провода на пути от датчиков концентрации тонера до платы.
    • Проверить систему подачи тонера – часто ломаются шестерни шнеков подачи тонера, которые находятся в блоке ленты переноса.

    • Опустить магнит в бункер отработки, чтобы выяснить имел ли место «вынос» девелопера в отработку.
    • При отсутствии девелопера в бункере отработки вручную добавить и распределить тонер в блок проявки. Добавлять через входное отверстие блока проявки, распределять вращением валов блока проявки за шестерню. Обычно для вывода машины из состояния ошибки достаточно добавить 3-5 г тонера и вращать вручную шестерню блока проявки 2-3 минуты.

    • При присутствии девелопера в бункере отработки сначала вручную добавить совместимый носитель в блок проявки, затем тонер. Добавлять через входное отверстие блока проявки, распределять вращением валов блока проявки за шестерню. Примерное количество носителя, которое нужно добавить, можно выяснить сравнением веса проблемного и «живого» блока проявки.
    • После входа машины на готовность запустить из меню машины процедуру DEV-CLN (1 раз, чтобы не заклинить систему вывода отработки!) затем калибровку цвета. Это позволит машине довести концентрацию тонера до установленных значений.
    • Обновление прошивки. Kyocera иногда вносит в прошивки коррекции, связанные с алгоритмом подкачки тонера.
    • Использование «нормального» тонера.
    • Беседа с клиентом о том, что офисная машина предназначена для печати офисных документов, а не для оперативной полиграфии и т.п.

    Ошибки у принтеров Kyocera FS-1020MFP, FS-1025MFP, FS-1030MFP, FS-1120MFP, FS-1125MFP, FS-1220MFP и прочих моделей? Советы по сбросу и устранению!

    Японский производитель оргтехники Kyocera выпускает одни из самых качественных печатающих устройств на рынке, которые, в первую очередь, пользуются высоким спросом у бизнеса. А это уже говорит о многом!

    Тем не менее, даже самая качественная оргтехника может давать сбои. Особенно, если за ней не следить!

    Поэтому сегодня мы рассмотрим наиболее распространенные коды ошибок у популярных принтеров Kyocera FS-1020MFP, FS-1025MFP, FS-1030MFP, FS-1120MFP, FS-1125MFP, FS-1220MFP и прочих моделей, чтобы разобраться, какие неполадки можно устранить своими руками, а в каких случаях необходимо воспользоваться помощью специалистов.

    Сброс ошибок у принтеров Kyocera своими руками

    Под сбросом ошибок у принтеров Kyocera нужно понимать комплекс мероприятий, которые потенциально может осуществить опытный пользователь, чтобы восстановить работоспособность печатающих устройств без обращения в сервисный центр.

    Ошибка №

    Причина

    Решение проблемы

    E-0001

    В принтере установлен совместимый картридж или чип расходника был поврежден.
    Проблема решается несколькими способами:

    1. установка оригинального картриджа;

    2. замена поврежденного чипа;

    3. прошивка принтера – затем в печатающее устройство можно будет установить любой картридж неограниченное количество раз;

    4. сброс ошибки – зажмите на несколько секунд кнопки «Режим» и «Сброс».

    E-0002

    Регион используемого картриджа не соответствует характеристикам принтера.
    Проблема решается несколькими способами:

    1. установка соответствующего региону принтера картриджа;

    3. прошивка принтера.

    E-0003

    Память печатающего устройства заполнена.
    Распечатайте уже отсканированные документы или сбросьте операцию соответствующей кнопкой.

    E-0007

    В картридже закончился тонер.
    Замените картридж на новый оригинальный, совместимый или заправьте расходник.

    E-0008

    Одна из крышек принтера не закрыта.
    Захлопните заднюю и переднюю крышки принтера, ощутив характерный щелчок.

    E-0009

    Лоток с отпечатками переполнен.
    Извлеките распечатанные листы с бумагой, а затем возобновите печать кнопкой «Старт».

    E-0012

    Память принтера заполнена.
    Измените разрешение печати в меньшую сторону – до 600 dpi.

    E-0014

    Установлена бумага такого формата, который принтер не поддерживает.
    Замените бумагу листами совместимого формата.

    Иногда функционал принтера может быть ограничен на софтверном уровне.

    Чтобы расширить диапазон форматов, мы рекомендуем обновить ПО печатающего устройства.

    E-0015

    1. У принтера отсутствует питание.

    2. Сетевой кабель не подключен.

    3. На персональном компьютере отсутствует драйвер.

    Проверьте целостность сетевого кабеля.

    При необходимости установите драйвер.

    E-0018

    Выбранный файл отсутствует в очереди на печать.
    Сбросьте операцию, нажав на кнопку «Сброс». Затем выберите новый файл и продолжите печать.

    E-0019

    Формат печати не поддерживается принтером.
    Сбросьте операцию, нажав на кнопку «Сброс».

    J-0511

    Бумагу зажевало.
    Аккуратно извлеките остатки бумаги из корпуса принтера.

    PF

    Отсутствует бумага во входном лотке.
    Установите бумагу во входной лоток и возобновите печать, нажав на кнопку «Старт».

    Устранение ошибок у принтеров Kyocera в сервисном центре

    Возможная причина

    0030

    0100

    Неисправна Flash-память или плата PWB.

    0120

    0190

    0630

    2000

    2. неисправен соединительный кабель или нарушена целостность соединения контактов;

    3. неисправен привод или его отдельные узлы.

    3100

    2. неисправен датчик положения;

    3. неисправен привод сканера;

    4. неисправна PWB-плата.

    3300

    2. неисправен датчик CIS;

    3. неисправна PWB-плата.

    3500

    4000

    2. неисправен привод;

    3. неисправна PWB-плата.

    4200

    2. неисправна PWB-плата и отдельные компоненты.

    6000

    2. неисправен термостат;

    3. неисправен нагреватель фьюзера;

    4. неисправна PWB-плата и отдельные компоненты.

    6020

    2. выявлен дефект у термистора.

    6030

    2. выявлен дефект у термистора;

    3. неисправен термостат;

    4. неисправна PWB-плата и отдельные компоненты.

    6400

    2. неисправна PWB-плата и отдельные компоненты.

    F000

    F020

    F040

    F05D

    2. неисправна PWB-плата и отдельные компоненты.

    Ошибка № Неисправна Flash-память.
    Неисправна Flash-память или плата PWB.
    Неисправна PWB-плата.
    1. Неисправна PWB-плата;
    1. Неисправен соединительный кабель или нарушена целостность соединения контактов;
    1. Неисправен соединительный кабель или нарушена целостность соединения контактов;
    Неисправна PWB-плата.
    1. Неисправен соединительный кабель или нарушена целостность соединения контактов;
    1. Неисправен соединительный кабель или нарушена целостность соединения контактов;
    1. Неисправен соединительный кабель или нарушена целостность соединения контактов;
    1. Неисправна PWB-плата и отдельные компоненты;
    1. Неисправен соединительный кабель или нарушена целостность соединения контактов;
    1. Неисправен соединительный кабель или нарушена целостность соединения контактов;
    Неисправна PWB-плата и отдельные компоненты.
    Неисправна PWB-плата.
    Неисправна PWB-плата.
    1. Неисправно программное обеспечение привода;

    Попытались самостоятельно устранить ошибку на принтере Kyocera, но проблемы с печатью остались нерешенными? Сервисный центр МосТонер – круглосуточный бесплатный выезд мастера в пределах МКАД. Вы платите только за результат!

    Продаётся Б/У ЗиП для Kyocera FS-C2026MFP,C2126MFP,C2026MFP+, C2126MFP+,C2526MFP,C2626MFP,C5150DN,C5250DN,P6021CDN,P6026CDN,M6526cdn,M6026cdn

    302KV93040 | FK-590 Печь в сборе FK-590 3500,00 руб
    302HN93013 | 2HN93010 | 2HN93011 | 2HN93012 | 2HN93013 | 302HN93010 | 302HN93011 | 302HN93012 | DV-560 DV560K Блок проявки DV-560K (чёрный цвет) 3500,00 руб
    302HN93023 | 2HN93020 | 302HN93020 | 302HN93021 | 302HN93022 | DV-560Y Блок проявки DV-560Y (жёлтый цвет) 3500,00 руб
    302HN93033 | 2HN93030 | 302HN93030 | 302HN93031 | 302HN93032 | DV-560C Блок проявки DV-560C (голубой цвет) 3500,00 руб
    302HN93043 | 2HN93040 | 2HN93041 | 2HN93042 | 2HN93043 | 302HN93040 | 302HN93041 | 302HN93042 | DV-560M Блок проявки DV-560M (пурпурный цвет) 3500,00 руб
    302KV93018 | 302KV93017 | 2KV93011 | 2KV93012 | 2KV93013 | 2KV93014 | 2KV93015 | 2KV93016 | 2KV93017 | 302KV93010 | 302KV93011 | 302KV93012 | 302KV93013 | 302KV93014 | 302KV93015 | 302KV93016 | DK-590 | T02KV00500 | 2KV93010 Драм-юнит DK-590 3500,00руб
    302KV93070 | TR-590 Узел переноса изображения TR-590 5000,00 руб

    Восстановление блоков проявок, замена девелопера.
    Устранение ошибки 7401, 7402, 7403, 7404 в цветных машинах Kyocera.

    Все современные копировальные аппараты, мфу и принтеры Kyocera имеют возможность диагностировать все узлы устройства в режиме запуска и во время работы аппарата. По этому, если во время включения или во время работы произошел сбой, то техника Kyocera сможет сообщить о наличии ошибки.

    В большинстве случаев у аппаратов Kyocera код ошибки отображается на дисплее, в остальных случаях тип ошибки зависит от последовательности и количества миганий индикаторов.
    Если Ваш копировальный аппарат, МФУ или принтер Kyocera выдал на дисплее некий код, то узнать причину, описание возникновения ошибки, а так же в каком узле аппарата стоит искать проблему, Вы можете в этом разделе выбрав интересующую модель из списка.

    Но диагностика не решит проблему сбоя аппарата, для этого лучше обратиться к профессиональным и опытным сервисным специалистам компании Kyomart! Позвоните нам по телефону
    8 (343) 288-23-45 или отправьте запрос на электронную почту: sales@kyomart.ru , и мы обязательно свяжемся с Вами в кратчайшие сроки.

    Код ошибки Описание ошибки Причина ошибки 0100 Backup memory device error Defective flash memory. Defective main PWB. 0120 MAC address data error
    For data in which the MAC address is invalid. Defective flash memory. Defective engine PWB. 0130 Backup memory read/write error (main NAMD) Flash memory (Control PWB) 0140 Backup memory data error (main NAND) Flash memory (Control PWB) 0150 Engine PWB EEPROM error
    Detecting engine PWB EEPROM communication error. Improper installation engine PWB EEPROM. Defective engine PWB. Device damage of EEPROM. 0170 Billing counting error
    A checksum error is detected in the main and engine backup memories for the billing counters. Data damage of EEPROM. Defective PWB. 0600 Expanded memory (DIMM) installing error
    The expansion memory modules (DIMM) are not correctly mounted. Improper installation expanded memory (DIMM). 0610 Expanded memory (DIMM) error
    The expansion memory modules (DIMM) mounted on the main PWB does not operate correctly. Defective expanded memory (DIMM). Defective main PWB. 0640 Hard disk error
    The hard disk cannot be accessed. Defective hard disk. Defective main PWB. 0840 Faults of RTC
    The time is judged to go back based on the comparison of the RTC time and the current time or five years or more have passed. The battery is disconnected from the main PWB. Defective main PWB. 0930 EEPROM bus error Defective drum PWB (EEPROM). Defective engine PWB (EEPROM). Defective engine PWB. Defective main PWB.OM. 1010 Lift motor error
    When the lift motor is driven, the motor over-current detection signal is detected continuously for 50 times (5 s) at 100 ms intervals. After the lift motor is driven, the ON status of lift sensor cannot be detected for 8 s. The cassette installed confirmation message is displayed on the operation panel, and even if the cassette is opened and closed, the cassette installed confirmation message is displayed 5 times successively. Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of the lift motor. Defective lift motor. Defective engine PWB. 1020 PF lift motor error (paper feeder 1)
    When the lift motor is driven, the motor over-current detection signal is detected continuously for 50 times (5 s) at 100 ms intervals. After the lift motor is driven, the ON status of lift sensor cannot be detected for 8 s. The cassette installed confirmation message is displayed on the operation panel, and even if the cassette is opened and closed, the cassette installed confirmation message is displayed 5 times successively. Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of the PF lift motor. Defective PF lift motor. Defective PF main PWB. 1030 PF lift motor error (paper feeder 2)
    When the lift motor is driven, the motor over-current detection signal is detected continuously for 50 times (5 s) at 100 ms intervals. After the lift motor is driven, the ON status of lift sensor cannot be detected for 8 s. The cassette installed confirmation message is displayed on the operation panel, and even if the cassette is opened and closed, the cassette installed confirmation message is displayed 5 times successively. Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of the PF lift motor. Defective PF lift motor. Defective PF main PWB. 1500 PF heater 1 high temperature error (paper feeder 1)
    A temperature higher than 75C/167F is detected. Defective connector cable or poor contact in the connector. Shorted PF thermistor 1. Defective PF fan motor 1. Defective PF main PWB. 1510 PF heater 2 high temperature error (paper feeder 1)
    A temperature higher than 75C/167F is detected. Defective connector cable or poor contact in the connector. Shorted PF thermistor 2. Defective PF fan motor 2. Defective PF main PWB. 1520 PF heater 1 high temperature error (paper feeder 2)
    A temperature higher than 75aC/167F is detected. Defective connector cable or poor contact in the connector. Shorted PF thermistor 1. Defective PF fan motor 1. Defective PF main PWB. 1530 PF heater 2 high temperature error (paper feeder 2)
    A temperature higher than 75C/167F is detected. Defective connector cable or poor contact in the connector. Shorted PF thermistor 2. Defective PF fan motor 2. Defective PF main PWB. 1600 PF heater 1 low temperature error (paper feeder 1)
    An external temperature higher than + 5C/+ 9F is not detected when one minute elapses after PF heater 1 is turned on. Defective connector cable or poor contact in the connector. PF thermistor 1 installed incorrectly. Defective PF thermistor 1. Broken PF heater 1. Defective PF heater PWB or PF main PWB. 1610 PF heater 2 low temperature error (paper feeder 1)
    An external temperature higher than + 5C/+ 9F is not detected when one minute elapses after PF heater 2 is turned on. Defective connector cable or poor contact in the connector. PF thermistor 2 installed incorrectly. Defective PF thermistor 2. Broken PF heater 2. Defective PF heater PWB or PF main PWB. 1620 PF heater 1 low temperature error (paper feeder 2)
    An external temperature higher than + 5C/+ 9F is not detected when one minute elapses after PF heater 1 is turned on. Defective connector cable or poor contact in the connector. PF thermistor 1 installed incorrectly. Defective PF thermistor 1. Broken PF heater 1. Defective PF heater PWB or PF main PWB. 1630 PF heater 2 low temperature error (paper feeder 2)
    An external temperature higher than + 5C/+ 9F is not detected when one minute elapses after PF heater 2 is turned on. Defective connector cable or poor contact in the connector. PF thermistor 2 installed incorrectly. Defective PF thermistor 2. Broken PF heater 2. Defective PF heater PWB or PF main PWB. 1800 Paper feeder communication error
    Communication error between engine PWB and optional paper feeder. Improper installation paper feeder. Defective connector cable or poor contact in the connector. Defective engine PWB. Defective PF main PWB. 2100 Developing motor error
    The developing motor ready input is not given for 5 s during the main motor is ON. Defective connector cable or poor contact in the connector. Defective drive transmission system of the developing motor. Defective developing motor. Defective engine PWB. 2200 Drum motor error
    The drum motor ready input is not given for 5 s during the drum motor is ON. Defective connector cable or poor contact in the connector. Defective drive transmission system of the drum motor. Defective drum motor. Defective engine PWB. 2330 Fuser pressure release motor error
    When the fuser pressure release motor is driven, the motor over-current detection signal is detected continuously for 8 times (800 ms) at 100 ms intervals. Defective connector cable or poor contact in the connector. Defective drive transmission system of the fuser pressure release motor. Defective fuser pressure release motor. Defective engine PWB. 2340 Fuser pressure release motor time-out error
    When the fuser pressure release motor is driven, the envelope switch (EVSW) is not detectable for 6 s. Defective connector cable or poor contact in the connector. Defective drive transmission system of the fuser pressure release motor. Defective fuser pressure release motor. Defective engine PWB. 2500 Paper feed motor error
    The drum motor ready input is not given for 5 s during the paper feed motor is ON. Defective connector cable or poor contact in the connector. Defective drive transmission system of the paper feed motor. Defective paper feed motor. Defective engine PWB. 2600 PF paper feed motor error (paper feeder 1)
    The drum motor ready input is not given for 2 s during the PF paper feed motor is ON. Defective connector cable or poor contact in the connector. Defective drive transmission system of the PF paper feed motor. Defective PF paper feed motor. Defective PF main PWB 2610 PF paper feed motor error (paper feeder 2)
    The drum motor ready input is not given for 2 s during the PF paper feed motor is ON. Defective connector cable or poor contact in the connector. Defective drive transmission system of the PF paper feed motor. Defective PF paper feed motor. Defective PF main PWB. 2730 Developing release motor error
    When the developing release motor is driven, the motor over-current detection signal is detected continuously for 8 times (800 ms) at 100 ms intervals. Defective connector cable or poor contact in the connector. Defective drive transmission system of the developing release motor. Defective developing release motor. Defective engine PWB. 2740 Developing release motor time-out error
    When the developing release motor is driven, the developing release switch (DEVRSW) is not detectable for 1 s. Defective connector cable or poor contact in the connector. Defective drive transmission system of the developing release motor. Defective developing release motor. Defective engine PWB. 2820 Fuser motor error
    The fuser motor ready input is not given for 5 s during the fuser motor is ON. Defective connector cable or poor contact in the connector. Defective drive transmission system of the fuser motor. Defective fuser motor. Defective engine PWB. 4001 Polygon motor KM error
    The polygon motor KM ready input is not given for 10 s during the polygon motor is ON. Defective connector cable or poor contact in the connector. Defective polygon motor KM. Defective engine PWB. 4002 Polygon motor CY error
    The polygon motor CY ready input is not given for 10 s during the polygon motor is ON. Defective connector cable or poor contact in the connector. Defective polygon motor CY. Defective engine PWB. 4201 Laser output error (black)
    The pin photo signal is not output from PD PWB K for one second while laser is emitted. Defective connector cable or poor contact in the connector. Defective APC PWB K. Defective PD PWB K. Defective engine PWB. 4202 Laser output error (cyan)
    The pin photo signal is not output from PD PWB C for one second while laser is emitted. Defective connector cable or poor contact in the connector. Defective APC PWB C. Defective PD PWB C. Defective engine PWB. 4203 Laser output error (magenta)
    The pin photo signal is not output from PD PWB M for one second while laser is emitted. Defective connector cable or poor contact in the connector. Defective APC PWB C. Defective PD PWB C. Defective engine PWB. 4204 Laser output error (yellow)
    The pin photo signal is not output from PD PWB Y for one second while laser is emitted. Defective connector cable or poor contact in the connector. Defective APC PWB C. Defective PD PWB C. Defective engine PWB. 4600 LSU cleaning motor error
    When the LSU cleaning motor is driven, the motor over-current detection signal is detected continuously for 50 times (5 s) at 100 ms intervals. Defective connector cable or poor contact in the connector. Defective drive transmission system of the LSU cleaning motor. Defective LSU cleaning motor. Defective engine PWB. 4700 VIDEO ASIC device error Defective connector cable or poor contact in the connector. Defective main PWB or engine PWB. 5301 Broken cleaning lamp K wire
    When the cleaning lamp K is driven, the lamp over-current detection signal is detected continuously for 10 times (1 s) at 100 ms intervals. Defective connector cable or poor contact in the connector. Defective cleaning lamp K. Defective engine PWB. 5302 Broken cleaning lamp C wire
    When the cleaning lamp C is driven, the lamp over-current detection signal is detected continuously for 10 times (1 s) at 100 ms intervals. Defective connector cable or poor contact in the connector. Defective cleaning lamp K. Defective engine PWB. 5303 Broken cleaning lamp M wire
    When the cleaning lamp M is driven, the lamp over-current detection signal is detected continuously for 10 times (1 s) at 100 ms intervals. Defective connector cable or poor contact in the connector. Defective cleaning lamp K. Defective engine PWB. 5304 Broken cleaning lamp Y wire
    When the cleaning lamp Y is driven, the lamp over-current detection signal is detected continuously for 10 times (1 s) at 100 ms intervals. Defective connector cable or poor contact in the connector. Defective cleaning lamp K. Defective engine PWB. 6000 Broken fuser heater wire
    The detected temperature of fuser thermistor does not rise 1„aC/1.8„aF after the fuser heater has been turned on continuously for 10 s in warming up. The fuser temperature does not reach 100„aC/212„aF after the fuser heater has been turned on continuously for 30 s in warming up. The detected temperature of fuser thermistor does not reach the specified temperature (ready indication temperature) after the fuser heater has been turned on continuously for 60 s in warming up. The detected temperature of fuser thermistor does not rise 1„aC/1.8„aF after the fuser heater has been turned on continuously for 10 s during printing. Defective connector cable or poor contact in the connector. Fuser thermostat triggered. Broken fuser heater wire. Defective engine PWB. 6020 Abnormally high fuser thermistor temperature
    The fuser thermistor detects a temperature higher than 240C/464F. By the activation of the high temperature error detection circuit (230C/446F or more) of fuser thermistor, the illumination of fuser heater was forcibly turned off and 10 s has elapsed. Shorted fuser thermistor. Defective engine PWB. 6030 Broken fuser thermistor wire
    Input from fuser thermistor is 3 or less (A/D value) continuously for 1 s. Defective connector cable or poor contact in the connector. Broken fuser thermistor wire. Fuser thermostat triggered. Broken fuser heater wire. Defective engine PWB. 6400 Zero-cross signal error
    The zero-cross signal does not reach the engine PWB for more than 1 s. Defective connector cable or poor contact in the connector. Defective power source PWB or engine PWB 7001 Toner motor K error
    When the toner motor K is driven, the motor over-current detection signal is detected continuously for 50 times (5 s) at 100 ms intervals. Defective connector cable or poor contact in the connector. Defective drive transmission system of the toner motor K. Defective toner motor K. Defective engine PWB. 7002 Toner motor C error
    When the toner motor C is driven, the motor over-current detection signal is detected continuously for 50 times (5 s) at 100 ms intervals. Defective connector cable or poor contact in the connector. Defective drive transmission system of the toner motor K. Defective toner motor K. Defective engine PWB. 7003 Toner motor M error
    When the toner motor M is driven, the motor over-current detection signal is detected continuously for 50 times (5 s) at 100 ms intervals. Defective connector cable or poor contact in the connector. Defective drive transmission system of the toner motor K. Defective toner motor K. Defective engine PWB. 7004 Toner motor Y error
    When the toner motor Y is driven, the motor over-current detection signal is detected continuously for 50 times (5 s) at 100 ms intervals. Defective connector cable or poor contact in the connector. Defective drive transmission system of the toner motor K. Defective toner motor K. Defective engine PWB. 7401 Developing unit K noninstalling error
    No density detection signal is output from toner sensor K in developing unit K. Defective connector cable or poor contact in the connector. Defective toner sensor K. Defective engine PWB. 7402 Developing unit C noninstalling error
    No density detection signal is output from toner sensor C in developing unit C. Defective connector cable or poor contact in the connector. Defective toner sensor K. Defective engine PWB. 7403 Developing unit M noninstalling error
    No density detection signal is output from toner sensor M in developing unit M. Defective connector cable or poor contact in the connector. Defective toner sensor K. Defective engine PWB. 7404 Developing unit Y noninstalling error
    No density detection signal is output from toner sensor Y in developing unit Y. Defective connector cable or poor contact in the connector. Defective toner sensor K. Defective engine PWB. 7411 Drum unit K non- installing error
    The EEPROM of drum PWB K does not communicate normally. Installation of incompatible drum unit K. Defective connector cable or poor contact in the connector. Defective drum PWB K. Defective engine PWB. 7412 Drum unit C non- installing error
    The EEPROM of drum PWB C does not communicate normally. Installation of incompatible drum unit K. Defective connector cable or poor contact in the connector. Defective drum PWB K. Defective engine PWB. 7413 Drum unit M non- installing error
    The EEPROM of drum PWB M does not communicate normally. Installation of incompatible drum unit K. Defective connector cable or poor contact in the connector. Defective drum PWB K. Defective engine PWB. 7414 Drum unit Y non- installing error
    The EEPROM of drum PWB Y does not communicate normally. Installation of incompatible drum unit K. Defective connector cable or poor contact in the connector. Defective drum PWB K. Defective engine PWB. 9530 Backup data error
    The serial number of the machine written on the EEPROM of the engine PWB differs with that is written on both the flash memory of the engine PWB and the EEPROM of the drum PWB as a backup. Replacing both the engine PWB and the drum unit at the same time. F000 Main PWB — operation panel PWB communication error Defective main PWB. Defective operation panel PWB. F010 Main PWB checksum error Defective main PWB F020 Main PWB RAM checksum errors Defective main memory (RAM) on the main PWB. Defective expanded memory (DIMM). F040 Main PWB — print engine communication error Defective main PWB. Defective engine PWB. F050 Print engine ROM checksum error Defective engine PWB. F278 Power supply in drive system error Main power switch was turned off without using the power key, or a power failure has occurred.
    • Code: 0100
    • Description: Backup memory device error
    • Causes: Defective flash memory. Defective main PWB.
    • Remedy: Defective flash memory. Replace the main PWB and check for correct operation.
      Defective main PWB. Replace the main PWB and check for correct operation.
    • Code: 0120
    • Description: MAC address data error
      For data in which the MAC address is invalid.
    • Causes: Defective flash memory. Defective engine PWB.
    • Remedy: Defective flash memory. Replace the main PWB and check for correct operation.
      Defective engine PWB. Replace the engine PWB and check for correct operation.
    • Code: 0130
    • Description: Backup memory read/write error (main PWB)
    • Causes: Defective flash memory. Defective main PWB.
    • Remedy: Defective flash memory. Replace the main PWB and check for correct operation.
      Defective main PWB. Replace the main PWB and check for correct operation.
    • Code: 0140
    • Description: Backup memory data error (main PWB)
    • Causes: Defective flash memory. Defective main PWB.
    • Remedy: Defective flash memory. Replace the main PWB and check for correct operation.
      Defective main PWB. Replace the main PWB and check for correct operation.
    • Code: 0150
    • Description: Engine PWB EEPROM error
      Detecting engine PWB EEPROM communication error.
    • Causes: Improper installation engine PWB EEPROM. Defective engine PWB. Device damage of EEPROM.
    • Remedy: Improper installation engine PWB EEPROM. Check the installation of the EEPROM and remedy if necessary.
      Defective engine PWB. Replace the engine PWB and check for correct operation.
      Device damage of EEPROM. Contact the Service Administrative Division.
    • Code: 0170
    • Description: Billing counting error
      A checksum error is detected in the main and engine backup memories for the billing counters.
    • Causes: Data damage of EEPROM. Defective PWB.
    • Remedy: Data damage of EEPROM. Contact the Service Administrative Division.
      Defective PWB. Replace the main PWB or the engine PWB and check for correct operation.
    • Code: 0600
    • Description: Expanded memory (DIMM) installing error
      The expansion memory modules (DIMM) are not correctly mounted.
    • Causes: Improper installation expanded memory (DIMM).
    • Remedy: Improper installation expanded memory (DIMM). Check the installation of the expanded memory (DIMM).
    • Code: 0610
    • Description: Expanded memory (DIMM) error
      The expansion memory modules (DIMM) mounted on the main PWB does not operate correctly.
    • Causes: Defective expanded memory (DIMM). Defective main PWB.
    • Remedy: Defective expanded memory (DIMM). Replace the expanded memory (DIMM) and check for correct operation.
      Defective main PWB. Replace the main PWB and check for correct operation.
    • Code: 0640
    • Description: SSD error
      The SSD cannot be accessed.
    • Causes: Defective SSD. Defective main PWB.
    • Remedy: Defective SSD. Replace the SSD and check for correct operation.
      Defective main PWB. Replace the main PWB and check for correct operation.
    • Code: 0840
    • Description: Faults of RTC
      The time is judged to go back based on the comparison of the RTC time and the current time or five years or more have passed.
    • Causes: The battery is disconnected from the main PWB. Defective main PWB.
    • Remedy: The battery is disconnected from the main PWB. Check visually and remedy if necessary
      Defective main PWB. Replace the main PWB and check for correct operation.
    • Code: 0930
    • Description: EEPROM bus error
    • Causes: Defective drum PWB (EEPROM). Defective engine PWB (EEPROM). Defective engine PWB. Defective main PWB.OM.
    • Remedy: Defective drum PWB (EEPROM). Replace the drum unit.
      Defective engine PWB (EEPROM). Replace the engine PWB and check for correct operation.
      Defective engine PWB. Replace the engine PWB and check for correct operation.
      Defective main PWB. Replace the main PWB and check for correct operation.
    • Code: 1010
    • Description: Lift motor error
      When the lift motor is driven, the motor over-current detection signal is detected continuously for 50 times (5 s) at 100 ms intervals. After the lift motor is driven, the ON status of lift sensor cannot be detected for 8 s. The cassette installed confirmation message is displayed on the operation panel, and even if the cassette is opened and closed, the cassette installed confirmation message is displayed 5 times successively.
    • Causes: Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of the lift motor. Defective lift motor. Defective engine PWB.
    • Remedy: Defective bottom plate elevation mechanism in the cassette. Check to see if the bottom plate can move smoothly and repair it if any problem is found.
      Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Lift motor and engine PWB (YC27)
      Defective drive transmission system of the lift motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
      Defective lift motor. Replace the lift motor
      Defective engine PWB. Replace the engine PWB and check for correct operation.
    • Code: 1020
    • Description: PF lift motor error (paper feeder 1)
      When the lift motor is driven, the motor over-current detection signal is detected continuously for 50 times (5 s) at 100 ms intervals. After the lift motor is driven, the ON status of lift sensor cannot be detected for 8 s. The cassette installed confirmation message is displayed on the operation panel, and even if the cassette is opened and closed, the cassette installed confirmation message is displayed 5 times successively.
    • Causes: Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of the PF lift motor. Defective PF lift motor. Defective PF main PWB.
    • Remedy: Defective bottom plate elevation mechanism in the cassette. Check to see if the bottom plate can move smoothly and repair it if any problem is found.
      Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF lift motor and PF main PWB (YC7)
      Defective drive transmission system of the PF lift motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
      Defective PF lift motor. Replace the PF lift motor
      Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder).
    • Code: 1030
    • Description: PF lift motor error (paper feeder 2)
      When the lift motor is driven, the motor over-current detection signal is detected continuously for 50 times (5 s) at 100 ms intervals. After the lift motor is driven, the ON status of lift sensor cannot be detected for 8 s. The cassette installed confirmation message is displayed on the operation panel, and even if the cassette is opened and closed, the cassette installed confirmation message is displayed 5 times successively.
    • Causes: Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of the PF lift motor. Defective PF lift motor. Defective PF main PWB.
    • Remedy: Defective bottom plate elevation mechanism in the cassette. Check to see if the bottom plate can move smoothly and repair it if any problem is found.
      Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF lift motor and PF main PWB (YC7)
      Defective drive transmission system of the PF lift motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
      Defective PF lift motor. Replace the PF lift motor
      Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder).
    • Code: 1040
    • Description: PF lift motor error (paper feeder 3)
      When the lift motor is driven, the motor over-current detection signal is detected continuously for 50 times (5 s) at 100 ms intervals. After the lift motor is driven, the ON status of lift sensor cannot be detected for 8 s. The cassette installed confirmation message is displayed on the operation panel, and even if the cassette is opened and closed, the cassette installed confirmation message is displayed 5 times successively.
    • Causes: Defective bottom plate elevation mechanism in the cassette. Defective connector cable or poor contact in the connector. Defective drive transmission system of the PF lift motor. Defective PF lift motor. Defective PF main PWB.
    • Remedy: Defective bottom plate elevation mechanism in the cassette. Check to see if the bottom plate can move smoothly and repair it if any problem is found.
      Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF lift motor and PF main PWB (YC7)
      Defective drive transmission system of the PF lift motor. Check if the gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
      Defective PF lift motor. Replace the PF lift motor
      Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder).
    • Code: 1500
    • Description: PF heater 1 high temperature error (paper feeder 1)
      A temperature higher than 75C/167F is detected.
    • Causes: Defective connector cable or poor contact in the connector. Shorted PF thermistor 1. Defective PF fan motor 1. Defective PF main PWB.
    • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF fan motor 1 and PF main PWB (YC111)
      Shorted PF thermistor 1. Replace the top heater unit (Refer to the service manual for the paper feeder).
      Defective PF fan motor 1. Replace the top heater unit (Refer to the service manual for the paper feeder).
      Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder).
    • Code: 1510
    • Description: PF heater 2 high temperature error (paper feeder 1)
      A temperature higher than 75C/167F is detected.
    • Causes: Defective connector cable or poor contact in the connector. Shorted PF thermistor 2. Defective PF fan motor 2. Defective PF main PWB.
    • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF fan motor 2 and PF main PWB (YC111)
      Shorted PF thermistor 2. Replace the side heater unit (Refer to the service manual for the paper feeder).
      Defective PF fan motor 2. Replace the side heater unit (Refer to the service manual for the paper feeder).
      Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder).
    • Code: 1520
    • Description: PF heater 1 high temperature error (paper feeder 2)
      A temperature higher than 75C/167F is detected.
    • Causes: Defective connector cable or poor contact in the connector. Shorted PF thermistor 1. Defective PF fan motor 1. Defective PF main PWB.
    • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF fan motor 1 and PF main PWB (YC111)
      Shorted PF thermistor 1. Replace the top heater unit (Refer to the service manual for the paper feeder).
      Defective PF fan motor 1. Replace the top heater unit (Refer to the service manual for the paper feeder).
      Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder).
    • Code: 1530
    • Description: PF heater 2 high temperature error (paper feeder 2)
      A temperature higher than 75C/167F is detected.
    • Causes: Defective connector cable or poor contact in the connector. Shorted PF thermistor 2. Defective PF fan motor 2. Defective PF main PWB.
    • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF fan motor 2 and PF main PWB (YC111)
      Shorted PF thermistor 2. Replace the side heater unit (Refer to the service manual for the paper feeder).
      Defective PF fan motor 2. Replace the side heater unit (Refer to the service manual for the paper feeder).
      Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder).
    • Code: 1540
    • Description: PF heater 1 high temperature error (paper feeder 3)
      A temperature higher than 75C/167F is detected.
    • Causes: Defective connector cable or poor contact in the connector. Shorted PF thermistor 1. Defective PF fan motor 1. Defective PF main PWB.
    • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF fan motor 1 and PF main PWB (YC111)
      Shorted PF thermistor 1. Replace the top heater unit (Refer to the service manual for the paper feeder).
      Defective PF fan motor 1. Replace the top heater unit (Refer to the service manual for the paper feeder).
      Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder).
    • Code: 1550
    • Description: PF heater 2 high temperature error (paper feeder 3)
      A temperature higher than 75C/167F is detected.
    • Causes: Defective connector cable or poor contact in the connector. Shorted PF thermistor 2. Defective PF fan motor 2. Defective PF main PWB.
    • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF fan motor 2 and PF main PWB (YC111)
      Shorted PF thermistor 2. Replace the side heater unit (Refer to the service manual for the paper feeder).
      Defective PF fan motor 2. Replace the side heater unit (Refer to the service manual for the paper feeder).
      Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder).
    • Code: 1600
    • Description: PF heater 1 low temperature error (paper feeder 1)
      An external temperature higher than + 5C/+ 9F is not detected when one minute elapses after PF heater 1 is turned on.
    • Causes: Defective connector cable or poor contact in the connector. PF thermistor 1 installed incorrectly. Defective PF thermistor 1. Broken PF heater 1. Defective PF heater PWB or PF main PWB.
    • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF heater 1 and PF heater PWB (YC1) PF heater PWB (YC3) and PF main PWB (YC113) PF thermistor 1 and PF main PWB (YC114)
      PF thermistor 1 installed incorrectly. Check the installation of the PF thermistor 1.
      Defective PF thermistor 1. Replace the top heater unit (Refer to the service manual for the paper feeder).
      Broken PF heater 1. Replace the top heater unit (Refer to the service manual for the paper feeder).
      Defective PF heater PWB or PF main PWB. Replace the PF heater PWB or PF main PWB (Refer to the service manual for the paper feeder).
    • Code: 1610
    • Description: PF heater 2 low temperature error (paper feeder 1)
      An external temperature higher than + 5C/+ 9F is not detected when one minute elapses after PF heater 2 is turned on.
    • Causes: Defective connector cable or poor contact in the connector. PF thermistor 2 installed incorrectly. Defective PF thermistor 2. Broken PF heater 2. Defective PF heater PWB or PF main PWB.
    • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF heater 2 and PF heater PWB (YC2) PF heater PWB (YC3) and PF main PWB (YC113) PF thermistor 2 and PF main PWB (YC115)
      PF thermistor 2 installed incorrectly. Check the installation of the PF thermistor 2.
      Defective PF thermistor 2. Replace the side heater unit (Refer to the service manual for the paper feeder).
      Broken PF heater 2. Replace the side heater unit (Refer to the service manual for the paper feeder).
      Defective PF heater PWB or PF main PWB. Replace the PF heater PWB or PF main PWB (Refer to the service manual for the paper feeder).
    • Code: 1620
    • Description: PF heater 1 low temperature error (paper feeder 2)
      An external temperature higher than + 5C/+ 9F is not detected when one minute elapses after PF heater 1 is turned on.
    • Causes: Defective connector cable or poor contact in the connector. PF thermistor 1 installed incorrectly. Defective PF thermistor 1. Broken PF heater 1. Defective PF heater PWB or PF main PWB.
    • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF heater 1 and PF heater PWB (YC1) PF heater PWB (YC3) and PF main PWB (YC113) PF thermistor 1 and PF main PWB (YC114)
      PF thermistor 1 installed incorrectly. Check the installation of the PF thermistor 1.
      Defective PF thermistor 1. Replace the top heater unit (Refer to the service manual for the paper feeder).
      Broken PF heater 1. Replace the top heater unit (Refer to the service manual for the paper feeder).
      Defective PF heater PWB or PF main PWB. Replace the PF heater PWB or PF main PWB (Refer to the service manual for the paper feeder).
    • Code: 1630
    • Description: PF heater 2 low temperature error (paper feeder 2)
      An external temperature higher than + 5C/+ 9F is not detected when one minute elapses after PF heater 2 is turned on.
    • Causes: Defective connector cable or poor contact in the connector. PF thermistor 2 installed incorrectly. Defective PF thermistor 2. Broken PF heater 2. Defective PF heater PWB or PF main PWB.
    • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF heater 2 and PF heater PWB (YC2) PF heater PWB (YC3) and PF main PWB (YC113) PF thermistor 2 and PF main PWB (YC115)
      PF thermistor 2 installed incorrectly. Check the installation of the PF thermistor 2.
      Defective PF thermistor 2. Replace the side heater unit (Refer to the service manual for the paper feeder).
      Broken PF heater 2. Replace the side heater unit (Refer to the service manual for the paper feeder).
      Defective PF heater PWB or PF main PWB. Replace the PF heater PWB or PF main PWB (Refer to the service manual for the paper feeder).
    • Code: 1640
    • Description: PF heater 1 low temperature error (paper feeder 3)
      An external temperature higher than + 5C/+ 9F is not detected when one minute elapses after PF heater 1 is turned on.
    • Causes: Defective connector cable or poor contact in the connector. PF thermistor 1 installed incorrectly. Defective PF thermistor 1. Broken PF heater 1. Defective PF heater PWB or PF main PWB.
    • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF heater 1 and PF heater PWB (YC1) PF heater PWB (YC3) and PF main PWB (YC113) PF thermistor 1 and PF main PWB (YC114)
      PF thermistor 1 installed incorrectly. Check the installation of the PF thermistor 1.
      Defective PF thermistor 1. Replace the top heater unit (Refer to the service manual for the paper feeder).
      Broken PF heater 1. Replace the top heater unit (Refer to the service manual for the paper feeder).
      Defective PF heater PWB or PF main PWB. Replace the PF heater PWB or PF main PWB (Refer to the service manual for the paper feeder).
    • Code: 1650
    • Description: PF heater 2 low temperature error (paper feeder 3)
      An external temperature higher than + 5C/+ 9F is not detected when one minute elapses after PF heater 2 is turned on.
    • Causes: Defective connector cable or poor contact in the connector. PF thermistor 2 installed incorrectly. Defective PF thermistor 2. Broken PF heater 2. Defective PF heater PWB or PF main PWB.
    • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF heater 2 and PF heater PWB (YC2) PF heater PWB (YC3) and PF main PWB (YC113) PF thermistor 2 and PF main PWB (YC115)
      PF thermistor 2 installed incorrectly. Check the installation of the PF thermistor 2.
      Defective PF thermistor 2. Replace the side heater unit (Refer to the service manual for the paper feeder).
      Broken PF heater 2. Replace the side heater unit (Refer to the service manual for the paper feeder).
      Defective PF heater PWB or PF main PWB. Replace the PF heater PWB or PF main PWB (Refer to the service manual for the paper feeder).
    • Code: 1800
    • Description: Paper feeder communication error
      Communication error between engine PWB and optional paper feeder.
    • Causes: Improper installation paper feeder. Defective connector cable or poor contact in the connector. Defective engine PWB. Defective PF main PWB.
    • Remedy: Improper installation paper feeder. Follow installation instruction carefully again.
      Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF main PWB (YC3) and engine PWB (YC33)
      Defective engine PWB. Replace the engine PWB and check for correct operation.
      Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder).
    • Code: 2100
    • Description: Developing motor error
      The developing motor ready input is not given for 5 s during the main motor is ON.А#`
    • Causes: Defective connector cable or poor contact in the connector. Defective drive transmission system of the developing motor. Defective developing motor. Defective engine PWB.
    • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Developing motor and engine PWB (YC14)
      Defective drive transmission system of the developing motor. Check if the rollers and gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
      Defective developing motor. Replace the developing motor.
      Defective engine PWB. Replace the engine PWB and check for correct operation.
    • Code: 2200
    • Description: Drum motor error
      The drum motor ready input is not given for 5 s during the drum motor is ON.
    • Causes: Defective connector cable or poor contact in the connector. Defective drive transmission system of the drum motor. Defective drum motor. Defective engine PWB.
    • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Drum motor and engine PWB (YC13)
      Defective drive transmission system of the drum motor. Check if the rollers and gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
      Defective drum motor. Replace the drum motor.
      Defective engine PWB. Replace the engine PWB and check for correct operation.
    • Code: 2330
    • Description: Fuser pressure release motor error
      When the fuser pressure release motor is driven, the motor over-current detection signal is detected continuously for 8 times (800 ms) at 100 ms intervals.
    • Causes: Defective connector cable or poor contact in the connector. Defective drive transmission system of the fuser pressure release motor. Defective fuser pressure release motor. Defective engine PWB.
    • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Fuser pressure release motor and engine PWB (YC38)
      Defective drive transmission system of the fuser pressure release motor. Check if the rollers and gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
      Defective fuser pressure release motor. Replace the fuser pressure release motor.
      Defective engine PWB. Replace the engine PWB and check for correct operation.
    • Code: 2340
    • Description: Fuser pressure release motor time-out error
      When the fuser pressure release motor is driven, the envelope switch (EVSW) is not detectable for 6 s.
    • Causes: Defective connector cable or poor contact in the connector. Defective drive transmission system of the fuser pressure release motor. Defective fuser pressure release motor. Defective engine PWB.
    • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Fuser pressure release motor and engine PWB (YC38)
      Defective drive transmission system of the fuser pressure release motor. Check if the rollers and gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
      Defective fuser pressure release motor. Replace the fuser pressure release motor.
      Defective engine PWB. Replace the engine PWB and check for correct operation.
    • Code: 2500
    • Description: Paper feed motor error
      The drum motor ready input is not given for 5 s during the paper feed motor is ON.
    • Causes: Defective connector cable or poor contact in the connector. Defective drive transmission system of the paper feed motor. Defective paper feed motor. Defective engine PWB.
    • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Paper feed motor and engine PWB (YC3)
      Defective drive transmission system of the paper feed motor. Check if the rollers and gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
      Defective paper feed motor. Replace the paper feed motor.
      Defective engine PWB. Replace the engine PWB and check for correct operation.
    • Code: 2600
    • Description: PF paper feed motor error (paper feeder 1)
      The drum motor ready input is not given for 2 s during the PF paper feed motor is ON.
    • Causes: Defective connector cable or poor contact in the connector. Defective drive transmission system of the PF paper feed motor. Defective PF paper feed motor. Defective PF main PWB.
    • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF paper feed motor and PF main PWB (YC6)
      Defective drive transmission system of the PF paper feed motor. Check if the rollers and gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
      Defective PF paper feed motor. Replace the PF paper feed motor.
      Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder).
    • Code: 2610
    • Description: PF paper feed motor error (paper feeder 2)
      The drum motor ready input is not given for 2 s during the PF paper feed motor is ON.
    • Causes: Defective connector cable or poor contact in the connector. Defective drive transmission system of the PF paper feed motor. Defective PF paper feed motor. Defective PF main PWB.
    • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF paper feed motor and PF main PWB (YC6)
      Defective drive transmission system of the PF paper feed motor. Check if the rollers and gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
      Defective PF paper feed motor. Replace the PF paper feed motor.
      Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder).
    • Code: 2620
    • Description: PF paper feed motor error (paper feeder 3)
      The drum motor ready input is not given for 2 s during the PF paper feed motor is ON.
    • Causes: Defective connector cable or poor contact in the connector. Defective drive transmission system of the PF paper feed motor. Defective PF paper feed motor. Defective PF main PWB.
    • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. PF paper feed motor and PF main PWB (YC6)
      Defective drive transmission system of the PF paper feed motor. Check if the rollers and gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
      Defective PF paper feed motor. Replace the PF paper feed motor.
      Defective PF main PWB. Replace the PF main PWB (Refer to the service manual for the paper feeder).
    • Code: 2730
    • Description: Developing release motor error
      When the developing release motor is driven, the motor over-current detection signal is detected continuously for 8 times (800 ms) at 100 ms intervals.
    • Causes: Defective connector cable or poor contact in the connector. Defective drive transmission system of the developing release motor. Defective developing release motor. Defective engine PWB.
    • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Developing release motor and engine PWB (YC35)
      Defective drive transmission system of the developing release motor. Check if the rollers and gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
      Defective developing release motor. Replace the developing release motor.
      Defective engine PWB. Replace the engine PWB and check for correct operation.
    • Code: 2740
    • Description: Developing release motor time-out error
      When the developing release motor is driven, the developing release switch (DEVRSW) is not detectable for 1 s.
    • Causes: Defective connector cable or poor contact in the connector. Defective drive transmission system of the developing release motor. Defective developing release motor. Defective engine PWB.
    • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Developing release motor and engine PWB (YC35)
      Defective drive transmission system of the developing release motor. Check if the rollers and gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
      Defective developing release motor. Replace the developing release motor.
      Defective engine PWB. Replace the engine PWB and check for correct operation.
    • Code: 2820
    • Description: Fuser motor error
      The fuser motor ready input is not given for 5 s during the fuser motor is ON.
    • Causes: Defective connector cable or poor contact in the connector. Defective drive transmission system of the fuser motor. Defective fuser motor. Defective engine PWB.
    • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Fuser motor and engine PWB (YC15)
      Defective drive transmission system of the fuser motor. Check if the rollers and gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
      Defective fuser motor. Replace the fuser motor.
      Defective engine PWB. Replace the engine PWB and check for correct operation.
    • Code: 4001
    • Description: Polygon motor KM error
      The polygon motor KM ready input is not given for 10 s during the polygon motor is ON.
    • Causes: Defective connector cable or poor contact in the connector. Defective polygon motor KM. Defective engine PWB.
    • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Laser scanner unit KM and engine PWB (YC31)
      Defective polygon motor KM. Replace the laser scanner unit KM.
      Defective engine PWB. Replace the engine PWB and check for correct operation.
    • Code: 4002
    • Description: Polygon motor CY error
      The polygon motor CY ready input is not given for 10 s during the polygon motor is ON.
    • Causes: Defective connector cable or poor contact in the connector. Defective polygon motor CY. Defective engine PWB.
    • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Laser scanner unit CY and engine PWB (YC31)
      Defective polygon motor CY. Replace the laser scanner unit CY.
      Defective engine PWB. Replace the engine PWB and check for correct operation.
    • Code: 4201
    • Description: Laser output error (black)
      The pin photo signal is not output from PD PWB K for one second while laser is emitted.
    • Causes: Defective connector cable or poor contact in the connector. Defective APC PWB K. Defective PD PWB K. Defective engine PWB.
    • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. APC PWB K and engine PWB (YC31)
      Defective APC PWB K. Replace the laser scanner unit KM.
      Defective PD PWB K. Replace the laser scanner unit KM.
      Defective engine PWB. Replace the engine PWB and check for correct operation.
    • Code: 4202
    • Description: Laser output error (cyan)
      The pin photo signal is not output from PD PWB C for one second while laser is emitted.
    • Causes: Defective connector cable or poor contact in the connector. Defective APC PWB C. Defective PD PWB C. Defective engine PWB.
    • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. APC PWB C and engine PWB (YC32)
      Defective APC PWB C. Replace the laser scanner unit CY.
      Defective PD PWB C. Replace the laser scanner unit CY.
      Defective engine PWB. Replace the engine PWB.
    • Code: 4203
    • Description: Laser output error (magenta)
      The pin photo signal is not output from PD PWB M for one second while laser is emitted.
    • Causes: Defective connector cable or poor contact in the connector. Defective APC PWB M. Defective PD PWB M. Defective engine PWB.
    • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. APC PWB M and engine PWB (YC31)
      Defective APC PWB M. Replace the laser scanner unit KM.
      Defective PD PWB M. Replace the laser scanner unit KM.
      Defective engine PWB. Replace the engine PWB.
    • Code: 4204
    • Description: Laser output error (yellow)
      The pin photo signal is not output from PD PWB Y for one second while laser is emitted.
    • Causes: Defective connector cable or poor contact in the connector. Defective APC PWB Y. Defective PD PWB Y. Defective engine PWB.
    • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. APC PWB Y and engine PWB (YC32)
      Defective APC PWB Y. Replace the laser scanner unit CY.
      Defective PD PWB Y. Replace the laser scanner unit CY.
      Defective engine PWB. Replace the engine PWB.
    • Code: 4600
    • Description: LSU cleaning motor error
      When the LSU cleaning motor is driven, the motor over-current detection signal is detected continuously for 50 times (5 s) at 100 ms intervals.
    • Causes: Defective connector cable or poor contact in the connector. Defective drive transmission system of the LSU cleaning motor. Defective LSU cleaning motor. Defective engine PWB.
    • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. LSU cleaning motor and engine PWB (YC36)
      Defective drive transmission system of the LSU cleaning motor. Check if the rollers and gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
      Defective LSU cleaning motor. Replace the LSU cleaning motor.
      Defective engine PWB. Replace the engine PWB and check for correct operation.
    • Code: 4700
    • Description: VIDEO ASIC device error
    • Causes: Defective connector cable or poor contact in the connector. Defective main PWB or engine PWB.
    • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Main PWB (YC39) and relay PWB (YC3) Relay PWB (YC2, 4) and engine PWB (YC8, 9)
      Defective main PWB or engine PWB. Replace the main PWB or the engine PWB and check for correct operation.
    • Code: 5301
    • Description: Broken cleaning lamp K wire
      When the cleaning lamp K is driven, the lamp over-current detection signal is detected continuously for 10 times (1 s) at 100 ms intervals.
    • Causes: Defective connector cable or poor contact in the connector. Defective cleaning lamp K. Defective engine PWB.
    • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Drum unit K and Drum relay PWB (YC2) Drum relay PWB (YC1) and engine PWB (YC34)
      Defective cleaning lamp K. Replace the drum unit K..
      Defective engine PWB. Replace the engine PWB and check for correct operation.
    • Code: 5302
    • Description: Broken cleaning lamp C wire
      When the cleaning lamp C is driven, the lamp over-current detection signal is detected continuously for 10 times (1 s) at 100 ms intervals.
    • Causes: Defective connector cable or poor contact in the connector. Defective cleaning lamp C. Defective engine PWB.
    • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Drum unit C and Drum relay PWB (YC4) Drum relay PWB (YC1) and engine PWB (YC34)
      Defective cleaning lamp C. Replace the drum unit C..
      Defective engine PWB. Replace the engine PWB and check for correct operation.
    • Code: 5303
    • Description: Broken cleaning lamp M wire
      When the cleaning lamp M is driven, the lamp over-current detection signal is detected continuously for 10 times (1 s) at 100 ms intervals.
    • Causes: Defective connector cable or poor contact in the connector. Defective cleaning lamp M. Defective engine PWB.
    • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Drum unit M and Drum relay PWB (YC3) Drum relay PWB (YC1) and engine PWB (YC34)
      Defective cleaning lamp M. Replace the drum unit M..
      Defective engine PWB. Replace the engine PWB and check for correct operation.
    • Code: 5304
    • Description: Broken cleaning lamp Y wire
      When the cleaning lamp Y is driven, the lamp over-current detection signal is detected continuously for 10 times (1 s) at 100 ms intervals.
    • Causes: Defective connector cable or poor contact in the connector. Defective cleaning lamp Y. Defective engine PWB.
    • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Drum unit Y and Drum relay PWB (YC5) Drum relay PWB (YC1) and engine PWB (YC34)
      Defective cleaning lamp Y. Replace the drum unit Y..
      Defective engine PWB. Replace the engine PWB and check for correct operation.
    • Code: 6000
    • Description: Broken fuser heater wire
      The detected temperature of fuser thermistor does not rise 1„aC/1.8„aF after the fuser heater has been turned on continuously for 10 s in warming up. The fuser temperature does not reach 100„aC/212„aF after the fuser heater has been turned on continuously for 30 s in warming up. The detected temperature of fuser thermistor does not reach the specified temperature (ready indication temperature) after the fuser heater has been turned on continuously for 60 s in warming up. The detected temperature of fuser thermistor does not rise 1„aC/1.8„aF after the fuser heater has been turned on continuously for 10 s during printing.
    • Causes: Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Fuser thermostat triggered. Broken fuser heater wire. Defective engine PWB.
    • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Fuser heater and power source PWB (YC102) Fuser unit and eject PWB (YC3) Eject PWB (YC1) and engine PWB (YC19)
      Fuser thermostat triggered. Reinsert the fuser unit.
      Broken fuser heater wire. Replace the fuser unit.
      Defective engine PWB. Replace the engine PWB and check for correct operation.
    • Code: 6020
    • Description: Abnormally high fuser thermistor temperature
      The fuser thermistor detects a temperature higher than 240C/464F. By the activation of the high temperature error detection circuit (230„aC/446„aF or more) of fuser thermistor, the illumination of fuser heater was forcibly turned off and 10 s has elapsed.
    • Causes: Deformed connector pin. Defective triac. Shorted fuser thermistor. Defective engine PWB.
    • Remedy: Shorted fuser thermistor. Replace the fuser unit.
      Defective engine PWB. Replace the engine PWB and check for correct operation.
    • Code: 6030
    • Description: Broken fuser thermistor wire
      Input from fuser thermistor is 3 or less (A/D value) continuously for 1 s.
    • Causes: Defective connector cable or poor contact in the connector. Deformed connector pin. Defective triac. Broken fuser thermistor wire. Fuser thermostat triggered. Broken fuser heater wire. Defective engine PWB.
    • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Fuser unit and eject PWB (YC3) Eject PWB (YC1) and engine PWB (YC19)
      Broken fuser thermistor wire. Replace the fuser unit.
      Fuser thermostat triggered. Reinsert the fuser unit.
      Broken fuser heater wire. Replace the fuser unit.
      Defective engine PWB. Replace the engine PWB and check for correct operation.
    • Code: 6400
    • Description: Zero-cross signal error
      The zero-cross signal does not reach the engine PWB for more than 1 s.
    • Causes: Defective connector cable or poor contact in the connector. Defective power source PWB or engine PWB.
    • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Power source PWB (YC103) and relay PWB (YC1) Relay PWB (YC4) and engine PWB (YC9)
      Defective power source PWB or engine PWB. Replace the power source PWB or the engine PWB and check for correct operation.
    • Code: 7001
    • Description: Toner motor K error
      When the toner motor K is driven, the motor over-current detection signal is detected continuously for 50 times (5 s) at 100 ms intervals.
    • Causes: Defective connector cable or poor contact in the connector. Defective drive transmission system of the toner motor K. Defective toner motor K. Defective engine PWB.
    • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Toner motor K and engine PWB (YC23)
      Defective drive transmission system of the toner motor K. Check if the rollers and gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
      Defective toner motor K. Replace the toner motor K.
      Defective engine PWB. Replace the engine PWB and check for correct operation.
    • Code: 7002
    • Description: Toner motor C error
      When the toner motor C is driven, the motor over-current detection signal is detected continuously for 50 times (5 s) at 100 ms intervals.
    • Causes: Defective connector cable or poor contact in the connector. Defective drive transmission system of the toner motor C. Defective toner motor C. Defective engine PWB.
    • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Toner motor C and engine PWB (YC25)
      Defective drive transmission system of the toner motor C. Check if the rollers and gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
      Defective toner motor C. Replace the toner motor C.
      Defective engine PWB. Replace the engine PWB and check for correct operation.
    • Code: 7003
    • Description: Toner motor M error
      When the toner motor M is driven, the motor over-current detection signal is detected continuously for 50 times (5 s) at 100 ms intervals.
    • Causes: Defective connector cable or poor contact in the connector. Defective drive transmission system of the toner motor M. Defective toner motor M. Defective engine PWB.
    • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Toner motor M and engine PWB (YC24)
      Defective drive transmission system of the toner motor M. Check if the rollers and gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
      Defective toner motor M. Replace the toner motor M.
      Defective engine PWB. Replace the engine PWB and check for correct operation.
    • Code: 7004
    • Description: Toner motor Y error
      When the toner motor Y is driven, the motor over-current detection signal is detected continuously for 50 times (5 s) at 100 ms intervals.
    • Causes: Defective connector cable or poor contact in the connector. Defective drive transmission system of the toner motor Y. Defective toner motor Y. Defective engine PWB.
    • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Toner motor Y and engine PWB (YC26)
      Defective drive transmission system of the toner motor Y. Check if the rollers and gears rotate smoothly. If not, grease the bushes and gears. Check for broken gears and replace if any.
      Defective toner motor Y. Replace the toner motor Y.
      Defective engine PWB. Replace the engine PWB and check for correct operation.
    • Code: 7401
    • Description: Developing unit K noninstalling error
      No density detection signal is output from toner sensor K in developing unit K.
    • Causes: Defective connector cable or poor contact in the connector. Defective toner sensor K. Defective engine PWB.
    • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Developing unit K and Drum relay PWB (YC6) Drum relay PWB (YC1) and engine PWB (YC34)
      Defective toner sensor K. Replace the developing unit K.
      Defective engine PWB. Replace the engine PWB and check for correct operation.
    • Code: 7402
    • Description: Developing unit C noninstalling error
      No density detection signal is output from toner sensor C in developing unit C.
    • Causes: Defective connector cable or poor contact in the connector. Defective toner sensor C. Defective engine PWB.
    • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Developing unit C and Drum relay PWB (YC10) Drum relay PWB (YC1) and engine PWB (YC34)
      Defective toner sensor C. Replace the developing unit C.
      Defective engine PWB. Replace the engine PWB and check for correct operation.
    • Code: 7403
    • Description: Developing unit M noninstalling error
      No density detection signal is output from toner sensor M in developing unit M.
    • Causes: Defective connector cable or poor contact in the connector. Defective toner sensor M. Defective engine PWB.
    • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Developing unit M and Drum relay PWB (YC7) Drum relay PWB (YC1) and engine PWB (YC34)
      Defective toner sensor M. Replace the developing unit M.
      Defective engine PWB. Replace the engine PWB and check for correct operation.
    • Code: 7404
    • Description: Developing unit Y noninstalling error
      No density detection signal is output from toner sensor Y in developing unit Y.
    • Causes: Defective connector cable or poor contact in the connector. Defective toner sensor Y. Defective engine PWB.
    • Remedy: Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Developing unit Y and Drum relay PWB (YC13) Drum relay PWB (YC1) and engine PWB (YC34)
      Defective toner sensor Y. Replace the developing unit Y.
      Defective engine PWB. Replace the engine PWB and check for correct operation.
    • Code: 7411
    • Description: Drum unit K non- installing error
      The EEPROM of drum PWB K does not communicate normally.
    • Causes: Installation of incompatible drum unit K. Defective connector cable or poor contact in the connector. Defective drum PWB K. Defective engine PWB.
    • Remedy: Installation of incompatible drum unit K. Install drum unit K compatible with the specifications to the machine.
      Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Drum unit K and Drum relay PWB (YC2) Drum relay PWB (YC1) and engine PWB (YC34)
      Defective drum PWB K. Replace the drum unit K.
      Defective engine PWB. Replace the engine PWB and check for correct operation.
    • Code: 7412
    • Description: Drum unit C non- installing error
      The EEPROM of drum PWB C does not communicate normally.
    • Causes: Installation of incompatible drum unit C. Defective connector cable or poor contact in the connector. Defective drum PWB C. Defective engine PWB.
    • Remedy: Installation of incompatible drum unit C. Install drum unit C compatible with the specifications to the machine.
      Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Drum unit C and Drum relay PWB (YC4) Drum relay PWB (YC1) and engine PWB (YC34)
      Defective drum PWB C. Replace the drum unit C.
      Defective engine PWB. Replace the engine PWB and check for correct operation.
    • Code: 7413
    • Description: Drum unit M non- installing error
      The EEPROM of drum PWB M does not communicate normally.
    • Causes: Installation of incompatible drum unit M. Defective connector cable or poor contact in the connector. Defective drum PWB M. Defective engine PWB.
    • Remedy: Installation of incompatible drum unit M. Install drum unit M compatible with the specifications to the machine.
      Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Drum unit M and Drum relay PWB (YC3) Drum relay PWB (YC1) and engine PWB (YC34)
      Defective drum PWB M. Replace the drum unit M.
      Defective engine PWB. Replace the engine PWB and check for correct operation.
    • Code: 7414
    • Description: Drum unit Y non- installing error
      The EEPROM of drum PWB Y does not communicate normally.
    • Causes: Installation of incompatible drum unit Y. Defective connector cable or poor contact in the connector. Defective drum PWB Y. Defective engine PWB.
    • Remedy: Installation of incompatible drum unit Y. Install drum unit Y compatible with the specifications to the machine.
      Defective connector cable or poor contact in the connector. Reinsert the connector. Also check for continuity within the connector cable. If none, replace the cable. Drum unit Y and Drum relay PWB (YC5) Drum relay PWB (YC1) and engine PWB (YC34)
      Defective drum PWB Y. Replace the drum unit Y.
      Defective engine PWB. Replace the engine PWB and check for correct operation.
    • Code: 9530
    • Description: Backup data error
      The serial number of the machine written on the EEPROM of the engine PWB differs with that is written on both the flash memory of the engine PWB and the EEPROM of the drum PWB as a backup.
    • Causes: Replacing both the engine PWB and the drum unit at the same time.
    • Remedy: Replacing both the engine PWB and the drum unit at the same time. Check that the machine operates properly by reverting the engine controller and the drum unit to the old ones. To replace the engine PWB and the drum unit at the same time, turn on the machine after replacing either one. Check that the machine operates properly and then turn off the machine. Replace the other and turn on the machine to check that the machine operates properly. Be sure to replace one by one.
    • Code: F000
    • Description: Main PWB — operation panel PWB communication error
    • Causes: Defective main PWB. Defective operation panel PWB.
    • Remedy: Defective main PWB. Turn the main power switch off/on to restart the machine. If the error is not resolved, replace main PWB.
      Defective operation panel PWB. Replace the operation panel PWB and check for correct operation.
    • Code: F010
    • Description: Main PWB checksum error
    • Causes: Defective main PWB.
    • Remedy: Defective main PWB. Turn the main power switch off/on to restart the machine. If the error is not resolved, replace main PWB.
    • Code: F020
    • Description: Main PWB RAM checksum error
    • Causes: Defective main memory (RAM) on the main PWB. Defective expanded memory (DIMM).
    • Remedy: Defective main memory (RAM) on the main PWB. Turn the main power switch off/on to restart the machine. If the error is not resolved, replace main PWB.
      Defective expanded memory (DIMM). Replace the expanded memory (DIMM).
    • Code: F040
    • Description: Main PWB — print engine communication error
    • Causes: Defective main PWB. Defective engine PWB.
    • Remedy: Defective main PWB. Turn the main power switch off/on to restart the machine. If the error is not resolved, replace main PWB.
      Defective engine PWB. Replace the engine PWB and check for correct operation.
    • Code: F050
    • Description: Print engine ROM checksum error
    • Causes: Defective engine PWB.
    • Remedy: Defective engine PWB. Turn the main power switch off/on to restart the machine. If the error is not resolved, replace engine PWB.
    • Code: F278
    • Description: Power supply in drive system error
    • Causes: Main power switch was turned off without using the power key, or a power failure has occurred.
    • Remedy: Turn on power. (To switch off power, first press the power key, then turn the main power switch off.)

    0 / 0 / 0

    Регистрация: 04.10.2022

    Сообщений: 2

    1

    04.10.2022, 12:58. Показов 249. Ответов 3


    Я являюсь сервисным специалистом организации, и обладаю определенными навыками ремонта. при замене фотобарабана синего цвета МФУ на новый, устройство отказывается загружаться и выдаёт ошибку 7402. Расходный материал установлен оригинальный. Так же при установке (старого) израсходованного блока проявки, МФУ загружается и функционирует. Перепрошивка аппарата на более новую версию выполнена, ошибка сохраняется. Пробовали при включенном аппарате на место исправного, ставить новый (неисправный) фотобарабан, МФУ его не принимает. Какие еще могут быть варианты устранения этой неисправности?

    __________________
    Помощь в написании контрольных, курсовых и дипломных работ, диссертаций здесь



    0



    Эксперт Hardware

    2459 / 923 / 177

    Регистрация: 03.03.2015

    Сообщений: 6,477

    04.10.2022, 14:03

    2

    Сначала изложите внятно, что меняди, на каком пробеге, с какой целью и по какой процедуре. Пока в ваших показаниях сплошные противоречия.



    0



    0 / 0 / 0

    Регистрация: 04.10.2022

    Сообщений: 2

    04.10.2022, 14:14

     [ТС]

    3

    МФУ полосил при печати. Поставили новый картридж/ МФУ выдаёт ошибку/Суть ошибок — машина не «видит» сигнала с датчика концентрации тонера в блоке проявки (7401 –Black, 7402 – Cyan, 7403 – Magenta, 7404 – Yellow).



    0



    Эксперт Hardware

    2459 / 923 / 177

    Регистрация: 03.03.2015

    Сообщений: 6,477

    04.10.2022, 18:36

    4

    Тумана поибавилось. К блоку барабана и проявки добавился еще и картридж. Кто будет разбираться в такой чехарде?



    0



    Понравилась статья? Поделить с друзьями:

    Читайте также:

  • Kyocera 2040 c6000 ошибка
  • Kyocera p2335dn коды ошибок
  • Kyocera 2035 узел проявки не установлен ошибка
  • Kyocera p2235dn коды ошибок
  • Kyocera 2035 ошибка f24c

  • 0 0 голоса
    Рейтинг статьи
    Подписаться
    Уведомить о
    guest

    0 комментариев
    Старые
    Новые Популярные
    Межтекстовые Отзывы
    Посмотреть все комментарии