-
#1
вот такие ошибки 210 и 560
210 | Power error status: 0x0000->0x0100 | 2021-05-22 09:34:18 |
560 | Slot0 loss balance | 2021-05-21 22:34:24 |
нигде нет расшифровки…команда whatminer`а сама шифруется((
помогите с диагностикой, ремонтом запуском асика
С чего всё началось…была сильная гроза, отключение эл.энергии(возможно были сильные просадки/скачки напруги), как итог у одного асика начались эти проблемы. Сбрасывал его полностью, перепрошивал и через SD и через веб, разбирал всё чистил соединения проверял чистил, видимого ничего нет. С БП на платы при запуске идёт 13в., продувается как положено и затем после второй продувки сбрасывает напряжение на хешплаты и ошибки в вебке такие появляются… Думаю на БП вот только с какой «стороны» к нему подходить… Прошу помогите кто сталкивался и что конкретно было/делали/ремонтировали. Просьба без советов что выкини/обратись в сервис центр/купи новый,не лезь сам раз не можешь…и т.д. и.т.п… За этим и прошу помощи!
-
#2
Ну да наиглупейший совет . Вот создал тему на клабе и сразу асик заработает .
-
#3
Ну да наиглупейший совет . Вот создал тему на клабе и сразу асик заработает .
а помочь без всяких «СЦ» жаба что ли удушит?
-
#4
а помочь без всяких «СЦ» жаба что ли удушит?
Да легко !!!
-
#5
вот такие ошибки 210 и 560
210 Power error status: 0x0000->0x0100 2021-05-22 09:34:18 560 Slot0 loss balance 2021-05-21 22:34:24 нигде нет расшифровки…команда whatminer`а сама шифруется((
помогите с диагностикой, ремонтом запуском асика
С чего всё началось…была сильная гроза, отключение эл.энергии(возможно были сильные просадки/скачки напруги), как итог у одного асика начались эти проблемы. Сбрасывал его полностью, перепрошивал и через SD и через веб, разбирал всё чистил соединения проверял чистил, видимого ничего нет. С БП на платы при запуске идёт 13в., продувается как положено и затем после второй продувки сбрасывает напряжение на хешплаты и ошибки в вебке такие появляются… Думаю на БП вот только с какой «стороны» к нему подходить… Прошу помогите кто сталкивался и что конкретно было/делали/ремонтировали. Просьба без советов что выкини/обратись в сервис центр/купи новый,не лезь сам раз не можешь…и т.д. и.т.п… За этим и прошу помощи!
Во-первых, полный лог асика в студию после запуска. Сколько потребляет энергии до появления этих ошибок и после. Запускаются ли все хэш-платы? Пробовал ли менять платы местами, вообще больше похоже на контрольку….
-
#6
Между ошибками прошло 12 часов? Т.е он не сразу их сыпет?
-
#7
Между ошибками прошло 12 часов? Т.е он не сразу их сыпет?
сразу, переставил БП всё заработало, проблема в БП 100%, что может с ним быть, он включается, контроллер вентиляторов работает, 12 вольт появляется два раза на 5-10секунд и после 12в отрубается и ошибка. Кто сталкивался с такой неисправностью БП? в чем может быть дело. Осцилографом щупал 12в когда появляется, ни просадок резких ни пульсаций нет
-
#8
я думал контроллер вентиляторов в чипе на контрольной плате сидит.
бп пока живы и хорошо с учетм цены P21D
-
#9
Может у кого то схема есть БП этого? или сталкивался кто то с похожим поведением БП и как это лечилось
-
#10
Может у кого то схема есть БП этого? или сталкивался кто то с похожим поведением БП и как это лечилось
порой хорошо ютуб, там есть канал Whatsminer с сервисными мануалами для ремонта БП и ХешПлат.
-
#11
210 блок питания ошибка …560 ошибка платы..
-
#12
Может у кого то схема есть БП этого? или сталкивался кто то с похожим поведением БП и как это лечилось
Чем кончилось?
-
#13
да ничем…5 месяцев провалялся асик не рабочий, некогда было заниматься совсем, теперь вот снова решил заняться
-
#14
Попробуйте снова включить. Бывают чудеса. Дайте знать
-
#15
Народ привет появились ошибки, whatminer 68 th, если кто подскажет буду благодарен, (но судя по форумам сейчас услышу и увижу всё что угодно кроме подсказок ) пока ищу сам решения, найду решение, обязательно отпишусь !
ErrorCode | Cause | Time |
---|---|---|
210 | Power error status: 0x0000->0x0080 | 2021-10-21 20:00:41 |
241 | Power output current unbalanced. code: 0x00000100 | 2021-10-21 19:59:01 |
560 | Slot0 loss balance | 2021-10-21 20:00:28 |
-
#16
Ошибка 0x0000->0x0080 лечится у нас в г.Ижевск за 4500р./шт
Успешный опыт по ней >10 шт.
-
#17
Ошибка 0x0000->0x0080 лечится у нас в г.Ижевск за 4500р./шт
Успешный опыт по ней >10 шт.
а ошибка 0x0000->0x0100 как то у вас лечится?
-
#18
а ошибка 0x0000->0x0100 как то у вас лечится?
Пока не встречалась
-
#19
Ошибка 0x0000->0x0080 лечится у нас в г.Ижевск за 4500р./шт
Успешный опыт по ней >10 шт.
Здравствуйте, как с вами связаться?
302
320
322
329
352
360
410
412
420
422
430
431
432
440
441
442
450
451
452
510
511
512
520
521
522
530
ли
разъем хэш-платы.
531
532
540
541
542
550
551
552
560
561
562
590
591
592
600
610
нормальный
режим
701
710
712
802
2000
2021
2030
2340
2350
5070
5072
5110
5112
8410
fan
fan
fan
fan
Inspection of input voltage in power grid
Error code
Коды ошибок асик майнера WhatsMiner
0 ErrSucc ОК ОК — обычный
21 ErrNotPlugged 1 или более хеш-плат не обнаружены Сигнал Hashboard PLUG не обнаружен Номер обнаруженной платы питания, если их более одной, разделенные пробелами 1. Проверьте правильность подключения кабеля SPI (по сравнению с обычной машиной) и снова подключите кабель. 2. Замените плату управления. 3. Замените проблемную доску хешрейта (переделайте доску головоломки).
22 ErrPsuI2cFail Аномальная связь по управлению питанием Неправильная связь I2C источника питания — 1. Заменить блок питания. 2. Замените плату управления.
23 ErrEncoreAllFail Все хэш-платы не могут быть включены SPI недоступен для всех плат хешрейта — 1. Убедитесь, что винты на обоих концах клеммы питания и соединения кабеля SPI не ослаблены. 2. Заменить блок питания. 3. Замените плату управления. 4. Отремонтируйте всю машину.
24 ErrEncoreFail Некоторые платы не включаются SPI недоступен на некоторых хэш-досках Номер хэшборда, для которого произошел сбой связи по SPI, если их несколько, разделенных пробелами 1. Убедитесь, что винты на обоих концах клеммы питания и соединения кабеля SPI не ослаблены. 2. Заменить блок питания. 3. Замените плату управления. 4. Замените проблемную хеш-доску (переделайте доску-головоломку).
25 ErrSetPllFail Не удалось поднять частоту хэш-платы Не удалось поднять частоту хэш-платы Номер хэшборда: частота ошибок 1. Убедитесь, что винты на обоих концах клеммы питания и соединения кабеля SPI не ослаблены. 2. Заменить блок питания. 3. Замените плату управления. 4. Замените проблемную хеш-доску (переделайте доску-головоломку).
26 ErrSetVolFail Не удалось установить напряжение Не удалось установить напряжение Номер хэшборда: 1/2 1. Убедитесь, что винты на обоих концах клеммы питания и соединения кабеля SPI не ослаблены. 2. Заменить блок питания. 3. Замените плату управления. 4. Заменить проблемную хеш-доску (присоединиться)
27 ErrBistFail Тест чипа BIST не пройден Тест чипа BIST не пройден Номер хэшборда: 1/2 1. Убедитесь, что винты на обоих концах клеммы питания и соединения кабеля SPI не ослаблены. 2. Заменить проблемную хеш-доску (присоединиться к плате)
28 ErrSpiFail Ненормальная связь платы хешрейта не может быть автоматически восстановлена ??во время работы Ненормальное соединение SPI платы хешрейта не может быть автоматически восстановлено во время работы Номер хэшборда 1. Убедитесь, что винты на обоих концах клеммы питания и соединения кабеля SPI не ослаблены. 2. Замените проблемную хеш-доску (переделайте доску-головоломку)
29 ErrI2cFail Ненормальная связь по питанию во время работы не может быть восстановлена ??автоматически Связь I2C с ненормальным источником питания не может быть автоматически восстановлена ??во время работы — 1. Заменить блок питания. 2. Замените плату управления.
30 ErrNetwork Подключение к майнинговому пулу прервано Подключение к майнинговому пулу прервано — Если эта проблема возникает на большом количестве или на всех майнинговых машинах с одним и тем же коммутатором: 1. Проверьте правильность настроек пула для майнинга. 2. Проверьте конфигурацию сетевой среды (например, конфигурацию DHCP, конфигурацию DNS, порт и т. Д.). Если проблемы возникают только на одной или нескольких машинах для майнинга: 1. Проверьте правильность настроек пула для майнинга. 2. Проверить подключения к сетевому порту майнера. 3. Замените сетевой кабель на работающую майнинговую машину. 4. Замените плату управления.
31 ErrBadChip Повреждение отдельных микросхем, что приводит к искусственно завышенной вычислительной мощности Повреждение отдельных микросхем, что приводит к искусственно завышенной вычислительной мощности Номер поврежденной микросхемы: номер хеш-платы, если их более одной, разделенные пробелами В ремонт
32 ErrOverheat Hashboard перегрелся Hashboard перегрелся Номер хэшборда 1. Проверьте, вращаются ли передний и задний вентиляторы, если они не вращаются, сначала замените вентиляторы, а затем замените плату управления / блок питания. 2. Убедитесь, что направление ветра спереди и сзади согласовано, согласуется ли оно с другими машинами, если нет, измените направление вентилятора. 3. Если температура воздуха на входе горной машины превышает 40 градусов, необходимо улучшить температурную среду в шахте. 4. Если определенная плата хешрейта часто перегревается, вы можете заменить проблемную плату хешрейта (переделайте головоломку).
33 ErrInvTemp Невозможно прочитать температуру чипа Невозможно прочитать температуру чипа Номер хэшборда 1. Убедитесь, что винты на обоих концах клеммы питания и соединения кабеля SPI не ослаблены. 2. Заменить блок питания. 3. Замените плату управления. 4. Замените проблемную хеш-доску (переделайте доску-головоломку).
34 ErrMisPlugged Неправильное подключение кабеля связи платы управления Ненормальное подключение кабеля SPI платы управления Номер хэшборда 1. Проверьте, совместим ли метод (последовательность) подключения кабеля SPI хэш-платы с другими машинами той же модели. 2. Замените плату управления.
35 ErrPsuFail Аномальный источник питания Аномальный источник питания 1. Обратите внимание на то, что если нет явного отклонения от нормы вычислительной мощности всей машины (не отключается плата), то перезагрузить 2. Убедитесь, что винты на обоих концах клеммы питания и соединения кабеля SPI не ослаблены. 3. Заменить блок питания.
36 ErrInvCorenum Некоторые чипы не работают должным образом Количество хороших фишек ненормальное Номер хэшборда: номер чипа 1. Обратите внимание на то, что если нет явного отклонения от нормы вычислительной мощности всей машины (не отключается плата), то перезагрузить 2. Перезапустите майнер, чтобы увидеть, появляется ли по-прежнему та же ошибка. 3. Замените проблемную хеш-плату.
37 ErrInvVidtype Тип платы управления / версия прошивки / количество микросхем не совпадает Тип платы управления / версия прошивки / количество микросхем не совпадает vidtype, minertype, subtype, chipnum После накопления нескольких единиц (> 10) обратитесь в ремонт.
38 ErrBadRearChips Наконец, у некоторых чипов низкая вычислительная мощность. Последние несколько уровней чипов имеют низкую вычислительную мощность В ремонт
39 ErrInvTuneParam Аномальные параметры старения Напряжение начальной частоты старения неверно В ремонт
Errcode | Scope of application | Explanation | Troubleshooting steps |
0 | Whole miner | Normal | Normal |
21 | hashboard | one or more hashboards can’t be detected | 1. check and see whether the SPI cables are firmly and correctly connected (compared the connection of cables with working miners), reconnect the SPI cables, don’t change sequence of connection 2. replace control board with other well functional one 3. replace defective hashboard(s) with other well functional one(s) (defective one should be returned for repair/replacement) |
22 | Whole miner | PSU communication is abnormal | 1. replace PSU with other well functional one 2. replace control board with other well functional one |
23 | Whole miner | All hashboards can’t be powered up | 1. check and see whether screws on the PSU side and SPI connection are loose 2. replace PSU with other well functional one 3. replace control board with other well functional one 4. whole miner should be returned for repair |
24 | hashboard | one or more hashboards can’t be powered up | 1. check and see whether screws on the PSU side and SPI connection are loose 2. replace PSU with other well functional one 3. replace control board with other well functional one 4. replace defective hashboard(s) with other well functional one(s) (defective one should be returned for repair/replacement) |
25 | hashboard | frequency increase of hashboards fails | 1. check hashrate of the miner, if there is nothing obviously abnormal (no missing hashboard), no action should be taken 2. check and see whether screws on the PSU side and SPI connection are loose 3. replace PSU with other well functional one 4. replace control board with other well functional one 5. replace defective hashboard(s) with other well functional one(s) (defective one should be returned for repair/replacement) |
26 | hashboard | voltage setting fails | 1. check and see whether screws on the PSU side and SPI connection are loose 2. replace PSU with other well functional one 3. replace control board with other well functional one 4. replace defective hashboard(s) with other well functional one(s) (defective one should be returned for repair/replacement) |
27 | hashboard | chip BIST test fails | 1. check and see whether screws on the PSU side and SPI connection are loose 2. replace defective hashboard(s) with other well functional one(s) (defective one should be returned for repair/replacement) |
28 | hashboard | abnormal communication of hashboard, it can’t be automatically recovered when running | 1. check and see whether screws on the PSU side and SPI connection are loose 2. replace defective hashboard(s) with other well functional one(s) (defective one should be returned for repair/replacement) |
29 | Whole miner | abnormal communication of PSU can’t be automatically recovered when running | 1. replace PSU with other well functional one 2. replace control board with other well functional one |
30 | Whole miner | pool disconnect | If the problem occurs in a large number of miners or all of the mines under the same switch: 1. please first check whether pool setting is correct 2. then check network configuration (such as DHCP configuration, DNS configuration, ports, etc.) If the problem occurs in only one or just a small number of miners under the same switch: 1. please first check whether pool setting is correct 2. then check whether network cable is firmly connected 3. replace network cable with other one from other well working miner 4. replace control board with other well functional one |
31 | hashboard | damage of some individual chip causes inflated high hashrate of the miner | no action should be taken |
32 | hashboard | hashboard overheat | 1. check and see whether both fans are spinning, if not, replace fan with other functional one, if still not, then replace control board or PSU 2. check and see whether wind direction of both fans are the same, whether wind direction are the same with other miners, if not, exchange fans 3. meter the inlet temperature of the miner, if above 40 °C, cooling system of the mining farm should be improved 4. if some hashboard is overheated frequently, that hashboard should be replaced (returned for repair) |
33 | hashboard | chip temperature can’t be read | 1. check and see whether screws on the PSU side and SPI connection are loose 2. replace PSU with other well functional one 3. replace control board with other well functional one 4. replace defective hashboard(s) with other well functional one(s) (defective one should be returned for repair/replacement) |
34 | cables of control board is connected incorrectly | 1. check hashrate of the miner, if there is nothing obviously abnormal (no missing hashboard), no action should be taken 2. check whether hashboard SPI cables are conneted in the same way (sequence) as other miners of same model 3. replace control board with other well functional one |
|
35 | hashboard | PSU voltage is too low | 1. check hashrate of the miner, if there is nothing obviously abnormal (no missing hashboard), no action should be taken 2.check and see whether screws on the PSU side and SPI connection is loose 3. replace PSU with other well functional one |
36 | hashboard | working or some chips is abnormal | 1. check hashrate of the miner, if there is nothing obviously abnormal (no missing hashboard), no action should be taken 2. reboot the miner to see whether the same error is given 3. replace defective hashboard(s) with other well functional one(s) (defective one should be returned for repair/replacement) |
37 | Whole miner | mismatch of control board version/firmware version/quantity of chips | if there are more than 10 miners with same error, please contact engineers |
38 | hashboard | low hashrate of last few chips | no action should be taken |
39 | hashboard | testing parameter is abnormal | no action should be taken |
40 | hashboard | PSU load is insufficient | 1. check and see whether screws on the PSU side and SPI connection are loose 2. replace PSU with other well functional one 3. replace defective hashboard(s) with other well functional one(s) (defective one should be returned for repair/replacement) |
41 | hashboard | startup voltage of PSU is too low | 1. check hashrate of the miner, if there is nothing obviously abnormal (no missing hashboard), no action should be taken 2. check and see whether screws on the PSU side and SPI connection are loose 3. replace PSU with other well functional one 4. replace control board with other well functional one |
42 | hashboard | implementation of plan B fails when hashboard frequency increases | 1. check hashrate of the miner, if there is nothing obviously abnormal (no missing hashboard), no action should be taken 2. check and see whether screws on the PSU side and SPI connection are loose 3. replace PSU with other well functional one 4. replace control board with other well functional one 5. replace defective hashboard(s) with other well functional one(s) (defective one should be returned for repair/replacement) |
Attention: 1. The miner should be powered up again to see whether it is back to normal after every step is taken 2. If the problem is not solve after replacement the part, the part should go back to its original unit 3. Error code and brief description of the problem should be attached to the hashboard that is confirmed defective and that will be returned for repair |
Error
code
Reason Processing method
110 Fanin detect speed error
Check whether the fan connection is normal,
or replace the power supply, or replace the
fan
111 Fanout detect speed error
Check whether the fan connection is normal,
or replace the power supply, or replace the
fan
130 Fanin speed error
Check whether the fan connection is normal,
or replace the power supply, or replace the
fan
131 Fanout speed error
Check whether the fan connection is normal,
or replace the power supply, or replace the
fan
140 Fan speed is too high Please check the environment temperature
200
Power probing error, no
power found
Detecting power output wiring, updating the
latest firmware, or replacing power supply
201
Power supply and
configuration file
mismatch
Replace the correct PSU
203 Power protecting Please check the environment temperature
204 Power current protecting Please check the environment temperature
205 Power current error Inspection of power supply in power grid
206 Power input voltage is low
Improve power supply conditions and input
voltage
207
Power input current
protecting
Improve power supply conditions and input
voltage
210 Power error status Check power failure code
213
Power input voltage and
current do not match the
power
Replace the PSU
233
Power output over
temperature protection
Please check the environment temperature
234
Power output over
temperature protection
Please check the environment temperature
235
Power output over
temperature protection
Please check the environment temperature
236
Overcurrent Protection of
Power Output
Please check the environment temperature,
check copper row screw
237
Overcurrent Protection of
Power Output
Please check the environment temperature,
check copper row screw
238
Overcurrent Protection of
Power Output
Please check the environment temperature,
check copper row screw
239
Overvoltage Protection of
Power Output
Inspection of power supply in power grid
240
Low Voltage Protection for
Power Output
Inspection of power supply in power grid
241
Power output current
imbalance
Replace the power
243
Over-temperature
Protection for Power Input
Please check the environment temperature
244
Over-temperature
Protection for Power Input
Please check the environment temperature
245
Over-temperature
Protection for Power Input
Please check the environment temperature
246
Overcurrent Protection for
Power Input
Please check the environment temperature
247
Overcurrent Protection for
Power Input
Please check the environment temperature
248
Overvoltage Protection for
Power Input
Inspection of input voltage in power grid
249
Overvoltage Protection for
Power Input
Inspection of input voltage in power grid
250
Undervoltage Protection
for Power Input
Inspection of input voltage in power grid
251
Undervoltage Protection
for Power Input
Inspection of input voltage in power grid
253 Power Fan Error Replace the PSU
254 Power Fan Error Replace the PSU
255
Protection of over power
output
Please check the environment temperature
256
Protection of over power
output
Please check the environment temperature
257
Input over current
protection of power supply
primary side
Try to power off and restart, no effect to
replace the power supply
263
Power communication
warning
Check whether the screws of the control
board are locked
264 Power communication error
Check whether the screws of the control
board are locked
267 Power watchdog protection Contact the technician in time
268
Power output over-current
protection
Check the ambient temperature, check the
copper bar screw
269
Power input over-current
protection
Improve power supply conditions and input
voltage
270
Power input over-voltage
protection
Inspection of input voltage in power grid
271
Power input under-voltage
protection
Inspection of input voltage in power grid
272
Warning of excessive power
output of power supply
Please check the environment temperature
273
Power input power too high
warning
Please check the environment temperature
274 Power fan warning
Check if the power fan is blocked and may
need to be replaced
275
Power over temperature
warning
Please check the environment temperature
300
SM0 temperature sensor
detection error
Check the connection of the hashboard
301
SM1 temperature sensor
detection error
Check the connection of the hashboard
302
SM2 temperature sensor
detection error
Check the connection of the hashboard
320
SM0 temperature reading
error
Check whether the control board screw is
locked properly, check the connection board
and the arrangement contact
321
SM1 temperature reading
error
Check whether the control board screw is
locked properly, check the connection board
and the arrangement contact
322
SM2 temperature reading
error
Check whether the control board screw is
locked properly, check the connection board
and the arrangement contact
329
Control board temperature
sensor communication error
Replace the power supply
350 SM0 temperature protecting Please check the environment temperature
351 SM1 temperature protecting Please check the environment temperature
352 SM2 temperature protecting Please check the environment temperature
410 SM0 detect eeprom error Check adapter board and wiring contact
411 SM1 detect eeprom error Check adapter board and wiring contact
412 SM2 detect eeprom error Check adapter board and wiring contact
420 SM0 parser eeprom error Contact the technician in time
421 SM1 parser eeprom error Contact the technician in time
422 SM2 parser eeprom error Contact the technician in time
430 SM0 chip bin type error Contact the technician in time
431 SM1 chip bin type error Contact the technician in time
432 SM2 chip bin type error Contact the technician in time
440
SM0 eeprom chip num X
error
Contact the technician in time
441
SM1 eeprom chip num X
error
Contact the technician in time
442
SM2 eeprom chip num X
error
Contact the technician in time
510 SM0 miner type error
The version and type of hashboard are
inconsistent, replace the correct hashboard
511 SM1 miner type error
The version and type of hashboard are
inconsistent, replace the correct hashboard
512 SM2 miner type error
The version and type of hashboard are
inconsistent, replace the correct hashboard
530 SM0 not found
Check the connection and arrangement of the
adapter board, or replace the control
board, check whether the hash board
connector is empty welded
531 SM1 not found
Check the connection and arrangement of the
adapter board, or replace the control
board, check whether the hash board
connector is empty welded
532 SM2 not found
Check the connection and arrangement of the
adapter board, or replace the control
board, check whether the hash board
connector is empty welded
540 SM0 reading chip id error
Check adapter board and wiring contact,
Clean the dust on the hashboard
541 SM1 reading chip id error
Check adapter board and wiring contact,
Clean the dust on the hashboard
542 SM2 reading chip id error
Check adapter board and wiring contact,
Clean the dust on the hashboard
550 SM0 have bad chips Replacement of bad chips
551 SM1 have bad chips Replacement of bad chips
552 SM2 have bad chips Replacement of bad chips
560 SM0 loss balance
Plug in the adapter plate, and then screw
in the power connection hashboard again
561 SM1 loss balance
Plug in the adapter plate, and then screw
in the power connection hashboard again
562 SM2 loss balance
Plug in the adapter plate, and then screw
in the power connection hashboard again
600
Environment temperature is
high
Please check the environment temperature
610
If the ambient temperature
is too high in high
performance mode, return
to normal mode
Check the ambient temperature, high
performance mode needs to be controlled
below 30 ?
710
Control board rebooted as
exception
Updating the latest firmware.Check whether
the control board screw is locked properly
800 cgminer checksum error Re-upgrade firmware
801
system-monitor checksum
error
Re-upgrade firmware
802
remote-daemon checksum
error
Re-upgrade firmware
2010 All pools are disable Please check the network or pools configure
2020 Pool0 connect failed Please check the network or pools configure
2021 Pool1 connect failed Please check the network or pools configure
2022 Pool2 connect failed Please check the network or pools configure
2030
High rejection rate of
pool
Please check the network or pools
configure.Setting of mining currency
2040
The pool does not support
the asicboost mode
Check pool configuration
5110 SM0 Frequency Up Timeout reboot
5111 SM1 Frequency Up Timeout reboot
5112 SM2 Frequency Up Timeout reboot
8410
Software version error
(M2x miner with M3x
firmware, or M3x with M2x
firmware).
Upgrade to the correct firmware version
PSU
Error
code
Reason processing method
0x0001 Input undervoltage Check the power supply
0x0002
Temperature sampling over
temperature protection of
power radiator
Power on again after 10 minutes of power
failure. If it occurs again, replace the
power supply
0x0004
Temperature sampling over
temperature protection of
power radiator
Power on again after 10 minutes of power
failure. If it occurs again, replace the
power supply
0x0008
Over temperature
protection of
environmental temperature
sampling in power supply
Power on again after 10 minutes of power
failure. If it occurs again, replace the
power supply
0x0010 Primary side over current
Power on again after 10 minutes of power
failure. If it occurs again, replace the
power supply
0x0020 Output undervoltage Check the power supply
0x0040
Output over current
(continuous load 320A for
more than 2S)
Tighten the copper bar screw again
0x0080 Primary side over current
Power on again after 10 minutes of power
failure. If it occurs again, replace the
power supply
0x0100
Single circuit overcurrent
(protection point 120a)
Check the PSU
0x0200
Single circuit overcurrent
(protection point 120a)
Check the PSU
0x0400
Single circuit overcurrent
(protection point 120a)
Check the PSU
0x0800 Fan failure Replace the PSU
0x1000
Output over current
(continuous load of 310A
for more than 5min)
Check the PSU
0x2000
Output over current
(continuous load 295A for
more than 10min)
Check the PS
Error code Reason Processing method 110 Fanin detect speed error Check whether the fan connection is normal, or replace the power supply, or replace the fan 111 Fanout detect speed error Check whether the fan connection is normal, or replace the power supply, or replace the fan 130 Fanin speed error Check whether the fan connection is normal, or replace the power supply, or replace the fan 131 Fanout speed error Check whether the fan connection is normal, or replace the power supply, or replace the fan 140 Fan speed is too high Please check the environment temperature 200 Power probing error, no power found Detecting power output wiring, updating the latest firmware, or replacing power supply 201 Power supply and configuration file mismatch Replace the correct PSU 203 Power protecting Please check the environment temperature 204 Power current protecting Please check the environment temperature 205 Power current error Inspection of power supply in power grid 206 Power input voltage is low Improve power supply conditions and input voltage 207 Power input current protecting Improve power supply conditions and input voltage 210 Power error status Check power failure code 213 Power input voltage and current do not match the power Replace the PSU 233 Power output over temperature protection Please check the environment temperature 234 Power output over temperature protection Please check the environment temperature 235 Power output over temperature protection Please check the environment temperature 236 Overcurrent Protection of Power Output Please check the environment temperature, check copper row screw 237 Overcurrent Protection of Power Output Please check the environment temperature, check copper row screw 238 Overcurrent Protection of Power Output Please check the environment temperature, check copper row screw 239 Overvoltage Protection of Power Output Inspection of power supply in power grid 240 Low Voltage Protection for Power Output Inspection of power supply in power grid 241 Power output current imbalance Replace the power 243 Over-temperature Protection for Power Input Please check the environment temperature 244 Over-temperature Protection for Power Input Please check the environment temperature 245 Over-temperature Protection for Power Input Please check the environment temperature 246 Overcurrent Protection for Power Input Please check the environment temperature 247 Overcurrent Protection for Power Input Please check the environment temperature 248 Overvoltage Protection for Power Input Inspection of input voltage in power grid 249 Overvoltage Protection for Power Input Inspection of input voltage in power grid 250 Undervoltage Protection for Power Input Inspection of input voltage in power grid 251 Undervoltage Protection for Power Input Inspection of input voltage in power grid 253 Power Fan Error Replace the PSU 254 Power Fan Error Replace the PSU 255 Protection of over power output Please check the environment temperature 256 Protection of over power output Please check the environment temperature 257 Input over current protection of power supply primary side Try to power off and restart, no effect to replace the power supply 263 Power communication warning Check whether the screws of the control board are locked 264 Power communication error Check whether the screws of the control board are locked 267 Power watchdog protection Contact the technician in time 268 Power output over-current protection Check the ambient temperature, check the copper bar screw 269 Power input over-current protection Improve power supply conditions and input voltage 270 Power input over-voltage protection Inspection of input voltage in power grid 271 Power input under-voltage protection Inspection of input voltage in power grid 272 Warning of excessive power output of power supply Please check the environment temperature 273 Power input power too high warning Please check the environment temperature 274 Power fan warning Check if the power fan is blocked and may need to be replaced 275 Power over temperature warning Please check the environment temperature 300 SM0 temperature sensor detection error Check the connection of the hashboard 301 SM1 temperature sensor detection error Check the connection of the hashboard 302 SM2 temperature sensor detection error Check the connection of the hashboard 320 SM0 temperature reading error Check whether the control board screw is locked properly, check the connection board and the arrangement contact 321 SM1 temperature reading error Check whether the control board screw is locked properly, check the connection board and the arrangement contact 322 SM2 temperature reading error Check whether the control board screw is locked properly, check the connection board and the arrangement contact 329 Control board temperature sensor communication error Replace the power supply 350 SM0 temperature protecting Please check the environment temperature 351 SM1 temperature protecting Please check the environment temperature 352 SM2 temperature protecting Please check the environment temperature 410 SM0 detect eeprom error Check adapter board and wiring contact 411 SM1 detect eeprom error Check adapter board and wiring contact 412 SM2 detect eeprom error Check adapter board and wiring contact 420 SM0 parser eeprom error Contact the technician in time 421 SM1 parser eeprom error Contact the technician in time 422 SM2 parser eeprom error Contact the technician in time 430 SM0 chip bin type error Contact the technician in time 431 SM1 chip bin type error Contact the technician in time 432 SM2 chip bin type error Contact the technician in time 440 SM0 eeprom chip num X error Contact the technician in time 441 SM1 eeprom chip num X error Contact the technician in time 442 SM2 eeprom chip num X error Contact the technician in time 510 SM0 miner type error The version and type of hashboard are inconsistent, replace the correct hashboard 511 SM1 miner type error The version and type of hashboard are inconsistent, replace the correct hashboard 512 SM2 miner type error The version and type of hashboard are inconsistent, replace the correct hashboard 530 SM0 not found Check the connection and arrangement of the adapter board, or replace the control board, check whether the hash board connector is empty welded 531 SM1 not found Check the connection and arrangement of the adapter board, or replace the control board, check whether the hash board connector is empty welded 532 SM2 not found Check the connection and arrangement of the adapter board, or replace the control board, check whether the hash board connector is empty welded 540 SM0 reading chip id error Check adapter board and wiring contact, Clean the dust on the hashboard 541 SM1 reading chip id error Check adapter board and wiring contact, Clean the dust on the hashboard 542 SM2 reading chip id error Check adapter board and wiring contact, Clean the dust on the hashboard 550 SM0 have bad chips Replacement of bad chips 551 SM1 have bad chips Replacement of bad chips 552 SM2 have bad chips Replacement of bad chips 560 SM0 loss balance Plug in the adapter plate, and then screw in the power connection hashboard again 561 SM1 loss balance Plug in the adapter plate, and then screw in the power connection hashboard again 562 SM2 loss balance Plug in the adapter plate, and then screw in the power connection hashboard again 600 Environment temperature is high Please check the environment temperature 610 If the ambient temperature is too high in high performance mode, return to normal mode Check the ambient temperature, high performance mode needs to be controlled below 30 ℃ 710 Control board rebooted as exception Updating the latest firmware.Check whether the control board screw is locked properly 800 cgminer checksum error Re-upgrade firmware 801 system-monitor checksum error Re-upgrade firmware 802 remote-daemon checksum error Re-upgrade firmware 2010 All pools are disable Please check the network or pools configure 2020 Pool0 connect failed Please check the network or pools configure 2021 Pool1 connect failed Please check the network or pools configure 2022 Pool2 connect failed Please check the network or pools configure 2030 High rejection rate of pool Please check the network or pools configure.Setting of mining currency 2040 The pool does not support the asicboost mode Check pool configuration 5110 SM0 Frequency Up Timeout reboot 5111 SM1 Frequency Up Timeout reboot 5112 SM2 Frequency Up Timeout reboot 8410 Software version error (M2x miner with M3x firmware, or M3x with M2x firmware). Upgrade to the correct firmware version PSU Error code Reason processing method 0x0001 Input undervoltage Check the power supply 0x0002 Temperature sampling over temperature protection of power radiator Power on again after 10 minutes of power failure. If it occurs again, replace the power supply 0x0004 Temperature sampling over temperature protection of power radiator Power on again after 10 minutes of power failure. If it occurs again, replace the power supply 0x0008 Over temperature protection of environmental temperature sampling in power supply Power on again after 10 minutes of power failure. If it occurs again, replace the power supply 0x0010 Primary side over current Power on again after 10 minutes of power failure. If it occurs again, replace the power supply 0x0020 Output undervoltage Check the power supply 0x0040 Output over current (continuous load 320A for more than 2S) Tighten the copper bar screw again 0x0080 Primary side over current Power on again after 10 minutes of power failure. If it occurs again, replace the power supply 0x0100 Single circuit overcurrent (protection point 120a) Check the PSU 0x0200 Single circuit overcurrent (protection point 120a) Check the PSU 0x0400 Single circuit overcurrent (protection point 120a) Check the PSU 0x0800 Fan failure Replace the PSU 0x1000 Output over current (continuous load of 310A for more than 5min) Check the PSU 0x2000 Output over current (continuous load 295A for more than 10min) Check the PS
Here is the WhatsMiner checklist of error code and we strongly recommend every WhatsMiner user to keep it because almost 80% of the problems can be solved by corresponding solutions.
We hope it is helpful for all WhatsMiner users. For rest of the problems, Kindly reach us and we’re willing to help.
Meaning of Error Code and Corresponding Solutions on WhatsM liner Tool 1 |
||
Error Code |
Meaning |
Corresponding Solutions |
110 |
Inlet fan detcction speed error |
Check whether the fan connction is normal, or replace the power supply, or replace the fan |
111 |
Outlet fan detection speed error |
|
120 | Inlet fan speed error(Deviation 2000+) | |
121 | Outlet fan speed error(Deviation 2000+) | |
130 |
Inlet fan speed error |
|
131 |
Outlet fan spced error |
|
140 |
Fan speed is too high |
Please check the environment temperature |
200 |
Power detection error |
Detecting the power output cable, or updating the latest firmware, or replacing the power supply |
201 |
Power does not match the configuration file |
Updating to the latest software |
202 |
Power output voltage error |
Updating to the latest software or check the power supply |
203 |
Power supply protection |
Please check the environment temperature |
204 |
Power supply current protection |
|
205 |
Power current error |
Inspection of power supply in power grid |
206 |
Power input voltage is low |
Improve power supply conditions and input voltage |
207 |
Power input current protecting |
|
210 |
Power status error |
Check the power failure code |
213 |
Power input voltage and current do not match the power |
Replace the PSU |
216 | Power remained unchanged for a long time | |
217 | Power set enable error | |
218 | Power input voltage is lower than 230V for high power mode | Increase input voltage,replace power supply |
233 |
Overtemperature Protection of Power Output |
Plcase check the environment temperature |
234 |
Overtemperature Protection of Power Output |
|
235 |
Overtemperature Protection of Power Output |
|
236 |
Overcurrent Protection of Power Output |
Please check the environment temperature and the copper wire screw(Recommend to use the protable electric screwdriver) |
237 |
Overcurrent Protection of Power Output |
|
238 |
Overcurrent Protection of Power Output |
|
239 |
Overvoltage Protection of Power Output |
Check grid power |
240 |
Low Voltage Protection for Power Output |
|
241 |
Power output current imbalance |
Replace the power |
243 |
Over-tempcrature Protection for Power Input |
Please check the environment temperature |
244 |
Over-temperature Protection for Power Input |
|
245 |
Over-tempcrature Protection for Power Input |
|
246 |
Overcurrent Protection for Power Input |
|
247 |
Overcurrent Protection for Power Input |
|
248 |
Overvoltage Protection for Power Input |
Check grid power |
249 |
Overvoltage Protection for Power Input |
|
250 |
Undervoltage Protection for Power Input |
|
251 |
Undervoltage Protection for Power Input |
|
253 |
Power Fan Error |
Replace the power supply |
254 |
Power Fan Error |
|
255 |
Protection of over power output |
Please check the environment temperature |
256 |
Protection of over power output |
|
257 |
Input over current protection of power supply primary side |
Try to power off and restart, no effect to replace the power supply |
263 |
Power communication warning |
Check whether the screws of the control board are locked |
264 |
Power communication error |
|
267 |
Power watchdog protection |
Contact the technician in time |
268 |
Power output over-current protection |
Check the ambient temperature, check the copper bar screw |
269 |
Power input over-current protection |
Improve power supply conditions and input voltage |
270 |
Power input over-voltage protection |
Inspection of input voltage in power grid |
271 |
Power input under-voltage protection |
|
272 |
Warning of excessive power output of power supply |
Please check the environment temperature |
273 |
Power input power too high warning |
|
274 |
Power fan warning |
Check if the power fan is blocked and may need to be replaced |
275 |
Power over temperature warning |
Please check the environment temperature |
Meaning of Error Code and Corresponding Solutions on WhatsMiner Tool 2 |
||
Error Code |
Meaning |
Corresponding Solutions |
300 |
SM0 temperature sensor detection error |
Check the connection of the hash board |
301 |
SM1 temperature sensor detection error |
|
302 |
SM2 temperature sensor detection error |
|
320 |
SM0 board temperature sensor communication error |
Check if the control panel screws are locked, check the adapter plate and the cable contacts |
321 |
SM1 board temperature sensor communication error |
|
322 |
SM2 board temperature sensor communication error |
|
329 |
Control board temperature sensor communication error |
Replace the power supply |
350 |
SM0 tempcrature protection |
Check the environment temperature (Recommend to use the GS320 infrared thermometer) |
351 |
M1 tempcrature protection |
|
352 |
SM2 tempcrature protection |
|
360 | The temperature of the hash board is overheating | |
410 |
SMO detect eeprom error |
Check adapter plate and cable contact |
411 |
SM1 detect eeprom error |
|
412 |
SM2 detect eeprom error |
|
420 |
SM0 parser eeprom error |
Upgrade firmware |
421 |
SM1 parser eeprom error |
|
422 |
SM2 parser eeprom error |
|
430 |
SM0 chip bin type error |
|
431 |
SM1 chip bin type error |
|
432 |
SM2 chip bin type error |
|
440 |
SM0 eeprom chip num X error |
|
441 |
SM1 eeprom chip num X error |
|
442 |
SM2 eeprom chip num X error |
|
450 | SM0 eeprom xfer error | Check adapter board and wiring contacts.Upgrade firmware |
451 | SM1 eeprom xfer error | |
452 | SM2 eeprom xfer error | |
510 |
SM0 miner type error |
The version and type of hashboard are inconsistent, replace the correct hashboard |
511 |
SM1 miner type error |
|
512 |
SM2 miner type error |
|
520 | SM0 bin type error | If the chip type of the hash board is inconsistent, replace the correct hash board. |
521 | SM1 bin type error | |
522 | SM2 bin type error | |
530 |
SM0 board is not detected |
Check the adapter board wiring and cablc, or replace the control board to check whether the hash board connector is soldered |
531 |
SM1 board is not detected |
|
532 |
SM2 board is not detected |
|
540 |
The number of SM0 chips is incomplete |
Check adapter plate and cable contact |
541 |
The number of SM1 chips is incomplete |
|
542 |
The number of SM2 chips is incomplete |
|
550 |
SM0 has bad chips |
Replace the bad chip in the print position |
551 |
SM1 has bad chips |
|
552 |
SM2 has bad chips |
|
560 |
SM0 loss balance |
Plug in the adapter plate, and then screw in the power connection hash board again |
561 |
SM1 loss balance |
|
562 |
SM2 loss balance |
|
590 |
SM0 frequency is too low |
Replace the hash board and place the hash boards which reported the same error together |
591 |
SM1 frequency is too low |
|
592 |
SM2 frequency is too low |
|
600 |
Environment temperature is too high |
Check the environment temperature |
610 |
If the ambient temperature is too high in high performance mode, return to normal mode |
Check the ambient temperature, high performance mode needs to be ontrolled below 30 ℃ |
701 | Control board no support chip | Upgrade the corresponding type of firmware |
710 |
Control board error |
Update to the latest firmware |
712 | Control board rebooted as exception | Updating the latest firmware.Check whether the control board screw is locked properly |
800 |
cgminer checksum error |
Re-upgrade firmware |
801 |
system-monitor checksum error |
|
802 |
system-monitor checksum error |
|
2000 | No pool information configured | Check pool configuration |
2010 |
All mining pool connections failed |
Check the network or mining pools setting |
2020 |
Mining pool0 connection failed |
|
2021 |
Mining pool1 connection failed |
|
2022 |
Mining pool2 connection failed |
|
2030 |
Mining pool rejcction rate is too high |
Check the network or mining pool setting, and the mining setting of the cryptocurrency |
2040 |
The pool does not support the asicboost mode |
Check pool configuration |
2310 | Hash rate is too low | Check input voltage, network environment, and ambient temperature |
2320 | Hash rate is too low | |
2340 | The loss of hash rate is too high | |
2350 | The loss of hash rate is too high | |
5070 | SM0 water velocity is abnormal | Check if the water flow is normal |
5071 | SM1 water velocity is abnormal | |
5072 | SM2 water velocity is abnormal | |
5110 |
SM0 Frequency Up Timeout |
reboot |
5111 |
SM1 Frequency Up Timeout |
|
5112 |
SM2 Frequency Up Timeout |
|
8410 | Software version error (M2x miner with M3x firmware, or M3x with M2x firmware) | Upgrade to the correct firmware version |
100001 | /antiv/signature Illegal | Upgrade the latest firmware or burn the card |
100002 | /antiv/dig/initd.dig Illegal | |
100003 |
/antiv/dig/pf_partial.dig Illegal |
PSU Error code |
Reason |
processing method |
0x0001 |
Input undervoltage |
Check the power supply |
0x0002 |
Temperature sampling over temperature protection of power radiator |
Power on again after 10 minutes of power failure. If it occurs again, replace the power supply |
0x0004 |
Temperature sampling over temperature protection of power radiator |
|
0x0008 |
Over temperature protection of environmental emperature sampling in power supply |
|
0x0010 |
Primary side over current |
Power on again after 10 minutes of power failure. If it occurs again, replace the power supply |
0x0020 |
Output undervoltage |
Check the power supply |
0x0040 |
Output over current (continuous load 320A for more than 2S) |
Tighten the copper bar screw again |
0x0080 |
Primary side over current |
Power on again after 10 minutes of power failure. If it occurs again, replace the power supply |
0x0100 |
Single circuit overcurrent (protection point 120a) |
Check the PSU |
0x0200 |
Single circuit overcurrent (protection point 120a) |
|
0x0400 |
Single circuit overcurrent (protection point 120a) |
|
0x0800 |
Fan failure |
Replace the PSU |
0x1000 |
Output over current (continuous load of 310A for more than 5min) |
Check the PSU |
0x2000 |
Output over current (continuous load 295A for more than 10min) |
We hope it is helpful for all WhatsMiner users. For rest of the problems, Kindly reach us and we’re willing to help.
- Manuals
- Brands
- MicroBT Manuals
- Computer Hardware
- WhatsMiner M20S
- Operation manual
-
Contents
-
Table of Contents
-
Bookmarks
Quick Links
WhatsMiner M20S Operation
Guide
V1.0
(Simplified Version)
Shenzhen MicroBT Electronics
Technology Co.,Ltd
1 / 32
Related Manuals for MicroBT WhatsMiner M20S
Summary of Contents for MicroBT WhatsMiner M20S
-
Page 1
WhatsMiner M20S Operation Guide V1.0 (Simplified Version) Shenzhen MicroBT Electronics Technology Co.,Ltd 1 / 32… -
Page 2: Table Of Contents
Catalog 1. M10S Product Introduction………………….3 2.Whats Miner Connection and Racking Safety Notes…………… 3 2.1.Miner Connection Notes…………………..3 2.1.1.Power Supply Control Wire Connection Notes…………4 2.1.2.Adapter Board Control Wire Connection Notes…………4 2.1.3.Fan Connection Notes………………..6 2.1.4.Hash Board and Adapter Board Connection Notes……….. 7 2.1.5.Power Supply Copper Busbar Connection Notes…………9 2.1.6.Product Connection Check………………10 2.2.Miner Handling and Racking Notes………………10…
-
Page 3: M10S Product Introduction
1. M10S Product Introduction Whats Miner M20S Blockchain Server Artifact Product ParameterIntroduction as below: HashRate:68TH/s ±5% Power:3264W±10% Power Rate:48W/T Power Supply:WhatsMiner Power Supply P21(220,3500W±10%) Environment Temperature:-5℃~40℃ Product Size:390mm*155mm*240mm 2.Whats Miner Connection and Racking Safety Notes 2.1.Miner Connection Notes Check over the miner’s power supply control wire and adapter board control wire and fan control wire to make sure connections are correct,the damage of control board、hash board、transfer board、fan, etc.
-
Page 4: Power Supply Control Wire Connection Notes
not be covered by the warranty. When connecting the wiring of the control board, the clasp must be corresponding, and the pin cannot be inserted into the socket by force.If the backplug, the power may burn the control board, burning the signal wire! 2.1.1.Power Supply Control Wire Connection Notes The power control wire is 14pin, and the card slot is inserted relative: Correct Connection:…
-
Page 5
Incorrect Connection: 5 / 32… -
Page 6: Fan Connection Notes
2.1.3.Fan Connection Notes The fan wire is 6pin, and the card slot is inserted relative: Correct Connection: 6 / 32…
-
Page 7: Hash Board And Adapter Board Connection Notes
Incorrect Connection: 2.1.4.Hash Board and Adapter Board Connection Notes The socket of the adapter board and the pin of the hash board must be installed in place to avoid other problems caused by contact problems! 7 / 32…
-
Page 8
Correct Connection: Incorrect Connection: 8 / 32… -
Page 9: Power Supply Copper Busbar Connection Notes
2.1.5.Power Supply Copper Busbar Connection Notes When the power supply copper busbar is connected to the hash board, the positive and negative poles of the copper busbar cannot be connected incorrectly, and the screw washers of the fixed copper bar must be aligned in parallel with the edge of the copper bar.
-
Page 10: Product Connection Check
2.1.6.Product Connection Check After all the connections of the miner are connected and all the screws are tightened, check again to confirm that the connection is correct. 2.2.Miner Handling and Racking Notes In the process of handling and racking of the miner, it is strictly forbidden to use the data cable, the power supply control wire and the fan wire as the load-bearing handle of the miner, and to pick up the machine and the power supply.
-
Page 11: Miner Configuration Environment Preparation
3. Miner Configuration Environment Preparation 3.1.Miner Configuration Equipment List Tool Numb Remark Computer Miner configuration Miner Power Power the miner Supply Configuring miner and The switch can Switch configuration computer connect to the network communication Internet. 1、Provide a dynamic IP It defaults to DHCP address for the initial DHCP/NTP…
-
Page 12: Miner Network Environment
3.2.Miner Network Environment The miner defaults to DHCP to obtain dynamic ip. Therefore, the mine network must be configured with a DHCP server, or the router can enable dhcp to dynamically allocate the IP address service.The running time of the miner, the correctness of the calculation statistics, etc.
-
Page 13: Miner Data Configuration(Configuration On The Web
washers of the fixed copper bar must be aligned parallel to the edge of the copper bar, and the fixed screws must be tightened, otherwise the power board may be burned out. , control board or power supply, hardware damage caused by copper stripping, is not covered by the warranty.
-
Page 14: Check The Ip Address Reported By The Miner
5.1.2.Check the IP address Reported by the Miner (1)After the machine is powered on for about 30s, under normal circumstances, the yellow light of the network port is always on and the green light is blinking. Press the IPFOUND function button (long button highlighted) on the miner control panel for more than 5s, the two LEDs on the right will flash a few times, indicating that the machine has broadcast the IP and MAC address of the unit to the network.
-
Page 15: Configuration Pool&Worker Data And Ntp Server Address
whether the switch is normal, the network cable connection is reliable, and the quality of the network cable is faulty. (3)The computer and miner running the WhatsMinerTools software must be on the same network segment. Otherwise, the software may not receive the broadcast message from the machine, so that the ip address and mac address information reported by the machine ipfound button cannot be queried.
-
Page 16
After the configuration of the mining pool is modified, the modified configuration must be restarted after the cgminer program is restarted or the control panel is restarted. (3)Restart cgminer to check whether the configuration modification takes effect. In the miner interface, select: Status-«CGMinerStatus» to enter the CGMiner running status interface. -
Page 17
(4)Restart the control board and check whether the configuration modification takes effect. (If you do not choose to restart cgminer, after the configuration is modified and saved, you can also restart the control board to make the configuration take effect.) In the system interface,click on”Reboot”. -
Page 18: Modify The Ntp Synchronization Server Address (Optional)
5.2.2.Modify the NTP Synchronization Server Address (optional) (1)After logging in, select System->>System Configuration in the interface to enter the Cgminer configuration page. (2)In the cgminer configuration interface, add or modify the NTP server address. The miner has been configured with four NTP server addresses by default. You can modify or add the NTP server address to the local NTP server address according to the mine situation.
-
Page 19
In the «Configuration» interface, click «Edit». (3) In the interface modification page, select «Static address» for the protocol and click (4) «Switch protocol». 19 / 32… -
Page 20: Miner Operation Status Check
(5)In the static address configuration interface, change the IP address, mask, gateway, broadcast address, and DNS address to the actual planned address of the mine. After editing, click «Save & Apply» in the lower right corner. After saving the application, you need to re-use the newly set static IP address to log in to the mining machine (otherwise the page will display loading until the loading fails).
-
Page 21
Notes: (1)The mining machine is connected correctly. When the network is normal, the mining machine will automatically perform the frequency search test after power-on. The search frequency test phase takes about 15 minutes. After the search frequency is over, it will enter the formal mining stage. -
Page 22: Miner Batch Data Configuration, Miner Status Check, Firmware Upgrade
7.Miner Batch Data Configuration, Miner Status Check, Firmware Upgrade You can use the WhatsMinerTool software to carry out batch data configuration, status check and firmware upgrade of the mining machine. For details, please refer to the «Whats Miner WhatsMinerTool Operation Guide». 8.Miner Disassembly and Installation 8.1.
-
Page 23
2)Unplug the power control cable and the adapter board control cable connected to the control panel as shown: 3)Remove the four screws fixed on the bracket and take out the control panel from the bracket as shown: 23 / 32… -
Page 24: Control Panel Installation
8.1.2.Control Panel Installation 1)When installing the control board, first fix the 4 screws on the control board bracket, as shown in the figure: 2)Insert the power control cable and the adapter board control cable into the corresponding slots on the control board, and then fix the bracket to the chassis with screws, as shown in the figure:…
-
Page 25: Power Supply Disassembly And Installation
8.2.Power Supply Disassembly and Installation 8.2.1.Power Supply Disassembly 1)Remove the four screws that secure the power supply on the chassis , and then remove the six screws that secure the copper bars on the power supply. Unplug the fan cable on the power supply . 2)After the above operation is completed, gently pull out the power supply (do not pull out too long, the power control cable is still connected to the control panel), as shown in the figure:…
-
Page 26: Power Supply Installation
3)Unplug the power control cable on the control panel, remove the power supply, and remove the power supply: 8.2.2.Power Supply Installation 1)First plug the control cable of the power supply into the corresponding slot on the control panel, as shown below: 2)Then connect the 6 positive and negative terminals on the power supply to the copper row one by one, and then install 6 screws in turn.
-
Page 27: Hash Board Disassembly And Installation
3)Finally, tighten the screws of the four fixed power supplies on the chassis, and the power supply is installed, as shown below: 8.3.Hash Board Disassembly and Installation 8.3.1.Hash Board Disassembly 1)There are three hash boards on each mining machine (the order number of the hash board is as shown below).
-
Page 28
2)Remove the adapter plate and the copper bar fixed to the control panel as shown: 3)Extract the faulty hash board outward, as shown: 28 / 32… -
Page 29
4)After taking out the hash board, record the serial number above or use WeChat “sweep” to scan the power board serial number and provide it to the relevant after- sales technician, as shown: 29 / 32… -
Page 30: Hash Board Installation
8.3.2.Hash Board Installation 1)When the hash board is loaded into the chassis, one hand holds the board into the hash board slot, and sequentially enters the chassis, as shown in the figure: 2)After installing the hash board into the chassis, first install the adapter board. The socket of the adapter board and the pin of the hash board must be installed in place to avoid other problems caused by contact problems, as shown:…
-
Page 31
After the adapter plate is installed, install the copper bar. When the power busbar is 3) connected to the hash board, the positive and negative poles of the copper bar cannot be connected incorrectly, and the screw pads of the fixed copper bar must be aligned with the edge of the copper bar, otherwise it may be possible to power on. -
Page 32
4)After the copper row is installed, the control board and the fan are installed, and the hash board is installed, as shown: 32 / 32…
- Manuals
- Brands
- MicroBT Manuals
- Computer Hardware
- WhatsMiner M20S
- Operation manual
-
Contents
-
Table of Contents
-
Bookmarks
Quick Links
WhatsMiner M20S Operation
Guide
V1.0
(Simplified Version)
Shenzhen MicroBT Electronics
Technology Co.,Ltd
1 / 32
Related Manuals for MicroBT WhatsMiner M20S
Summary of Contents for MicroBT WhatsMiner M20S
-
Page 1
WhatsMiner M20S Operation Guide V1.0 (Simplified Version) Shenzhen MicroBT Electronics Technology Co.,Ltd 1 / 32… -
Page 2: Table Of Contents
Catalog 1. M10S Product Introduction………………….3 2.Whats Miner Connection and Racking Safety Notes…………… 3 2.1.Miner Connection Notes…………………..3 2.1.1.Power Supply Control Wire Connection Notes…………4 2.1.2.Adapter Board Control Wire Connection Notes…………4 2.1.3.Fan Connection Notes………………..6 2.1.4.Hash Board and Adapter Board Connection Notes……….. 7 2.1.5.Power Supply Copper Busbar Connection Notes…………9 2.1.6.Product Connection Check………………10 2.2.Miner Handling and Racking Notes………………10…
-
Page 3: M10S Product Introduction
1. M10S Product Introduction Whats Miner M20S Blockchain Server Artifact Product ParameterIntroduction as below: HashRate:68TH/s ±5% Power:3264W±10% Power Rate:48W/T Power Supply:WhatsMiner Power Supply P21(220,3500W±10%) Environment Temperature:-5℃~40℃ Product Size:390mm*155mm*240mm 2.Whats Miner Connection and Racking Safety Notes 2.1.Miner Connection Notes Check over the miner’s power supply control wire and adapter board control wire and fan control wire to make sure connections are correct,the damage of control board、hash board、transfer board、fan, etc.
-
Page 4: Power Supply Control Wire Connection Notes
not be covered by the warranty. When connecting the wiring of the control board, the clasp must be corresponding, and the pin cannot be inserted into the socket by force.If the backplug, the power may burn the control board, burning the signal wire! 2.1.1.Power Supply Control Wire Connection Notes The power control wire is 14pin, and the card slot is inserted relative: Correct Connection:…
-
Page 5
Incorrect Connection: 5 / 32… -
Page 6: Fan Connection Notes
2.1.3.Fan Connection Notes The fan wire is 6pin, and the card slot is inserted relative: Correct Connection: 6 / 32…
-
Page 7: Hash Board And Adapter Board Connection Notes
Incorrect Connection: 2.1.4.Hash Board and Adapter Board Connection Notes The socket of the adapter board and the pin of the hash board must be installed in place to avoid other problems caused by contact problems! 7 / 32…
-
Page 8
Correct Connection: Incorrect Connection: 8 / 32… -
Page 9: Power Supply Copper Busbar Connection Notes
2.1.5.Power Supply Copper Busbar Connection Notes When the power supply copper busbar is connected to the hash board, the positive and negative poles of the copper busbar cannot be connected incorrectly, and the screw washers of the fixed copper bar must be aligned in parallel with the edge of the copper bar.
-
Page 10: Product Connection Check
2.1.6.Product Connection Check After all the connections of the miner are connected and all the screws are tightened, check again to confirm that the connection is correct. 2.2.Miner Handling and Racking Notes In the process of handling and racking of the miner, it is strictly forbidden to use the data cable, the power supply control wire and the fan wire as the load-bearing handle of the miner, and to pick up the machine and the power supply.
-
Page 11: Miner Configuration Environment Preparation
3. Miner Configuration Environment Preparation 3.1.Miner Configuration Equipment List Tool Numb Remark Computer Miner configuration Miner Power Power the miner Supply Configuring miner and The switch can Switch configuration computer connect to the network communication Internet. 1、Provide a dynamic IP It defaults to DHCP address for the initial DHCP/NTP…
-
Page 12: Miner Network Environment
3.2.Miner Network Environment The miner defaults to DHCP to obtain dynamic ip. Therefore, the mine network must be configured with a DHCP server, or the router can enable dhcp to dynamically allocate the IP address service.The running time of the miner, the correctness of the calculation statistics, etc.
-
Page 13: Miner Data Configuration(Configuration On The Web
washers of the fixed copper bar must be aligned parallel to the edge of the copper bar, and the fixed screws must be tightened, otherwise the power board may be burned out. , control board or power supply, hardware damage caused by copper stripping, is not covered by the warranty.
-
Page 14: Check The Ip Address Reported By The Miner
5.1.2.Check the IP address Reported by the Miner (1)After the machine is powered on for about 30s, under normal circumstances, the yellow light of the network port is always on and the green light is blinking. Press the IPFOUND function button (long button highlighted) on the miner control panel for more than 5s, the two LEDs on the right will flash a few times, indicating that the machine has broadcast the IP and MAC address of the unit to the network.
-
Page 15: Configuration Pool&Worker Data And Ntp Server Address
whether the switch is normal, the network cable connection is reliable, and the quality of the network cable is faulty. (3)The computer and miner running the WhatsMinerTools software must be on the same network segment. Otherwise, the software may not receive the broadcast message from the machine, so that the ip address and mac address information reported by the machine ipfound button cannot be queried.
-
Page 16
After the configuration of the mining pool is modified, the modified configuration must be restarted after the cgminer program is restarted or the control panel is restarted. (3)Restart cgminer to check whether the configuration modification takes effect. In the miner interface, select: Status-«CGMinerStatus» to enter the CGMiner running status interface. -
Page 17
(4)Restart the control board and check whether the configuration modification takes effect. (If you do not choose to restart cgminer, after the configuration is modified and saved, you can also restart the control board to make the configuration take effect.) In the system interface,click on”Reboot”. -
Page 18: Modify The Ntp Synchronization Server Address (Optional)
5.2.2.Modify the NTP Synchronization Server Address (optional) (1)After logging in, select System->>System Configuration in the interface to enter the Cgminer configuration page. (2)In the cgminer configuration interface, add or modify the NTP server address. The miner has been configured with four NTP server addresses by default. You can modify or add the NTP server address to the local NTP server address according to the mine situation.
-
Page 19
In the «Configuration» interface, click «Edit». (3) In the interface modification page, select «Static address» for the protocol and click (4) «Switch protocol». 19 / 32… -
Page 20: Miner Operation Status Check
(5)In the static address configuration interface, change the IP address, mask, gateway, broadcast address, and DNS address to the actual planned address of the mine. After editing, click «Save & Apply» in the lower right corner. After saving the application, you need to re-use the newly set static IP address to log in to the mining machine (otherwise the page will display loading until the loading fails).
-
Page 21
Notes: (1)The mining machine is connected correctly. When the network is normal, the mining machine will automatically perform the frequency search test after power-on. The search frequency test phase takes about 15 minutes. After the search frequency is over, it will enter the formal mining stage. -
Page 22: Miner Batch Data Configuration, Miner Status Check, Firmware Upgrade
7.Miner Batch Data Configuration, Miner Status Check, Firmware Upgrade You can use the WhatsMinerTool software to carry out batch data configuration, status check and firmware upgrade of the mining machine. For details, please refer to the «Whats Miner WhatsMinerTool Operation Guide». 8.Miner Disassembly and Installation 8.1.
-
Page 23
2)Unplug the power control cable and the adapter board control cable connected to the control panel as shown: 3)Remove the four screws fixed on the bracket and take out the control panel from the bracket as shown: 23 / 32… -
Page 24: Control Panel Installation
8.1.2.Control Panel Installation 1)When installing the control board, first fix the 4 screws on the control board bracket, as shown in the figure: 2)Insert the power control cable and the adapter board control cable into the corresponding slots on the control board, and then fix the bracket to the chassis with screws, as shown in the figure:…
-
Page 25: Power Supply Disassembly And Installation
8.2.Power Supply Disassembly and Installation 8.2.1.Power Supply Disassembly 1)Remove the four screws that secure the power supply on the chassis , and then remove the six screws that secure the copper bars on the power supply. Unplug the fan cable on the power supply . 2)After the above operation is completed, gently pull out the power supply (do not pull out too long, the power control cable is still connected to the control panel), as shown in the figure:…
-
Page 26: Power Supply Installation
3)Unplug the power control cable on the control panel, remove the power supply, and remove the power supply: 8.2.2.Power Supply Installation 1)First plug the control cable of the power supply into the corresponding slot on the control panel, as shown below: 2)Then connect the 6 positive and negative terminals on the power supply to the copper row one by one, and then install 6 screws in turn.
-
Page 27: Hash Board Disassembly And Installation
3)Finally, tighten the screws of the four fixed power supplies on the chassis, and the power supply is installed, as shown below: 8.3.Hash Board Disassembly and Installation 8.3.1.Hash Board Disassembly 1)There are three hash boards on each mining machine (the order number of the hash board is as shown below).
-
Page 28
2)Remove the adapter plate and the copper bar fixed to the control panel as shown: 3)Extract the faulty hash board outward, as shown: 28 / 32… -
Page 29
4)After taking out the hash board, record the serial number above or use WeChat “sweep” to scan the power board serial number and provide it to the relevant after- sales technician, as shown: 29 / 32… -
Page 30: Hash Board Installation
8.3.2.Hash Board Installation 1)When the hash board is loaded into the chassis, one hand holds the board into the hash board slot, and sequentially enters the chassis, as shown in the figure: 2)After installing the hash board into the chassis, first install the adapter board. The socket of the adapter board and the pin of the hash board must be installed in place to avoid other problems caused by contact problems, as shown:…
-
Page 31
After the adapter plate is installed, install the copper bar. When the power busbar is 3) connected to the hash board, the positive and negative poles of the copper bar cannot be connected incorrectly, and the screw pads of the fixed copper bar must be aligned with the edge of the copper bar, otherwise it may be possible to power on. -
Page 32
4)After the copper row is installed, the control board and the fan are installed, and the hash board is installed, as shown: 32 / 32…
Прошивки Whatsminer
Обновление прошивки асиков от MicroBT выполняется через специальную программу WhatsMinerTool.
Официальные прошивки MicroBT WhatsMiner
файл | версия прошивки | совместимость |
Стоковые прошивки для обновления через WhatsMinerTool | ||
whatsminer-M2x-h6-20200422.14.bin | M21s, M20s, M21 Control board H6 |
|
whatsminer-M2x-h3-20200611.23.bin | M21s, M20s, M21 Control board H3 |
|
whatsminer-M2x-h3-20200616.22.bin | M21s, M20s, M21 Control board H3 |
|
whatsminer-M2x-h3-20200917.22.bin | M21s, M20s, M21 Control board H3 |
|
whatsminer-M2x-h3-full-20200917.22.bin | M21s, M20s, M21 Control board H3 |
|
whatsminer-M2x-1920-h3-20201202.12.bin | M21s, M20s, M21 Control board H3 |
|
whatsminer-M2x-1920-h6os-20201202.22.bin | M21s, M20s, M21 Control board H6os |
|
whatsminer-M2x-1920-h6os-20210114.22.bin | M21s, M20s, M21 Control board H6os |
|
whatsminer-M2x-all-20210413.bin | M21s, M20s, M21 Control board any |
|
whatsminer-M2x-1920-h3-20210520.22.bin | 20210520.22.REL.U10 работает Adjust Freq |
M21s, M20s, M21 Control board H3 |
whatsminer-M2x-h3-full-20210520.22.bin | 20210520.22.REL.U10 | M21s, M20s, M21 Control board H3 |
whatsminer-M2x-1920-h6os-20210520.22.bin | 20210520.22.REL.U10 | M21s, M20s, M21 Control board H6os |
whatsminer-M2x-h6os-full-20210520.22.bin | 20210520.22.REL.U10 | M21s, M20s, M21 Control board H6os |
whatsminer-M2x-h6os-full-20210602.22.bin | 20210520.22.REL.U10 | M21s, M20s, M21 Control board H6os |
whatsminer-M2x-h3-full-20211103.22.bin | 20211103.22.REL.U10 | M21s, M20s, M21 Control board H3 |
whatsminer-M2x-1920-h3-20211130.22.bin | 20211130.22.REL.U10 | M21s, M20s, M21 Control board H3 |
whatsminer-M2x-1920-h6os-20211130.22.bin | 20211130.22.REL.U10 | M21s, M20s, M21 Control board H6os |
whatsminer-M2x-1920-h3-20220104.22.bin | 20220104.22.REL | M21s, M20s, M21 Control board H3 |
20220214.17.REL | ||
Whatsminer-M2x-all-20220511.19.bin | 20220422.17.REL.U10 | M21s, M20s, M21 Control board any |
Whatsminer-M2x-all-20220919.15.bin | 20220919.15.REL | M21s, M20s, M21 Control board any |
whatsminer-M3x-h3-20200609.00.bin | ||
whatsminer-M3x-h3-20200623.22.bin | ||
whatsminer-M3x-h6os-20200709.23.bin | ||
whatsminer-M3x-h6-20200917.22.bin | ||
whatsminer-M3x-ALL-h3-20211207.14.bin | ||
whatsminer-M3x-1930-h3-full-20210520.22.bin | ||
whatsminer-M3x-ALL-h616-20220421.19.bin | ||
whatsminer-M3x-ALL-h6os-20220421.19.bin | ||
Whatsminer-M3x-all-20220512.17.bin | ||
whatsminer-M3x-ALL-h6os-20220718.17.bin | ||
whatsminer-M3x-ALL-h616-20220802.15.bin | 20220802.15.REL | |
whatsminer-M3x-ALL-h6os-20220802.15.bin | 20220802.15.REL | M30s, M31s Control board H6OS |
Whatsminer-M3x-all-20221009.17.bin | 20221009.17.Rel | |
20221024.11.REL | ||
upgrade-whatsminer-h3-20200113.22.bin | ||
whatsminer-all-20210602.bin |
Официальные прошивки для иммерсионного охлаждения
Официальные прошивки WhatsMiner для иммерсионного охлаждения. Обновляются через WhatsMinerTool. Не использовать на воздушном охлаждении! Использование данных прошивок лишает ASIC-майнер гарантии производителя!
Майнер на данных прошивках не будет выдавать ошибок по высокой температуру окружающей среды и вентилятором, что позволяет использование асиков в иммерсионной ванне.
Для перевода на иммерсионное (жидкостное) охлаждение производитель выпустил утилиту WhatsPowerTool (AirToLiquid), которая сама скачивает нужную прошивку.
Официальные прошивки для иммерсионного охлаждения | ||
whatsminer-M2x-all-liquid-20200801.bin | M20s, M21s Control board H3, H6OS, H616 |
|
whatsminer-M2x-h3-liquid-20200917.22.bin | M20s, M21s Control board H3 |
|
whatsminer-M2x-all-liquid-20201202.bin | M20s, M21s Control board H3, H6OS, H616 |
|
whatsminer-M2x-all-liquid-20210322.bin | M20s, M21s Control board H3, H6OS, H616 |
|
whatsminer-M2x-all-liquid-20210413.bin | M20s, M21s Control board H3, H6OS, H616 |
|
whatsminer-M2x-1920-h3-liquid-20210520.22.bin | M20s, M21s Control board H3 |
|
whatsminer-M2x-all-liquid-20210520.bin | M20s, M21s Control board H3, H6OS, H616 |
|
whatsminer-M3x-all-liquid-20200801.bin | M30s, M31s Control board H3, H6OS, H616 |
|
whatsminer-M3x-h3-liquid-20200917.22.bin | M30s, M31s Control board H3 |
|
whatsminer-all-liquid-20211116.23.bin | M2x, M3x Control board H3, H6OS, H616 |
|
whatsminer-all-liquid-20211230.23.bin | M2x, M3x Control board H3, H6OS, H616 |
|
whatsminer-all-liquid-20220109.23.bin | M2x, M3x Control board H3, H6OS, H616 |
|
whatsminer-all-liquid-20220111.20.bin | M2x, M3x Control board H3, H6OS, H616 |
|
whatsminer-all-liquid-20220221.19.bin | M2x, M3x Control board H3, H6OS, H616 |
|
whatsminer-all-liquid-20220228.20.bin | M2x, M3x Control board H3, H6OS, H616 |
|
whatsminer-all-liquid-20220414.13.bin | M2x, M3x Control board H3, H6OS, H616 |
|
Whatsminer-all-liquid-20220620.11.bin | M2x, M3x Control board H3, H6OS, H616 |
|
Whatsminer-all-liquid-20220621.11.bin | M2x, M3x Control board H3, H6OS, H616 |
|
Whatsminer-all-liquid-20220622.11.bin | M2x, M3x Control board H3, H6OS, H616 |
|
Whatsminer-all-liquid-20220624.11.bin | M2x, M3x Control board H3, H6OS, H616 |
|
Whatsminer-all-liquid-20220627.10.bin | M2x, M3x Control board H3, H6OS, H616 |
|
Whatsminer-all-liquid-20220628.16.bin | M2x, M3x Control board H3, H6OS, H616 |
|
Прошивки для восстановления через MicroSD | ||
Тестовые прошивки
Используются при диагностике и ремонте Whatsminer
Прошивки контрольной платы для диагности | ||
whatsminer-testpower-20220420.bin | 20220420 | Пршивка для тестов БП Control board H3, H6OS, H616 |
WhatsMiner-Factory-Test-M3-H3-20190801.14.img | образ SD-карты | Whatsminer M3 Control board H3 |
WhatsMiner-Factory-Test-M2x-h3-20210201.22.img | образ SD-карты | Whatsminer M20s, M21s Control board H3 |
WhatsMiner-Factory-Test-M3x-h6os-20210312.16.img | образ SD-карты | Whatsminer M30s, 321s Control board H6OS |
WhatsMiner-Factory-Test-M3x-h3-20210430.22.img | образ SD-карты | Whatsminer M30s, 321s Control board H3 |
WhatsMiner-Factory-Test-1950-1960-h6os-20220505.17.img | образ SD-карты | Whatsminer M50 Control board H6OS |
WhatsMiner-Factory-Test-M2x-h6os-20210516.22.img | образ SD-карты | Whatsminer M20s, M21s Control board H6OS |
Прошивки БП
Прошивки WhatsPower оригинальные | ||
whatspower-P221Bv6-P221B_Sec_APP_4.4.bin | ||
whatspower-P221Cv6-P221C_sec_v6.8.bin | ||
whatspower-P222Bv6-P222B_Sec_APPv3.4.bin | ||
whatspower-P222Cv6-P222C_Sec_APPv4.4.bin | ||
назад