Ошибка авторазмера bizhub 163

12

If a printing error occurs, the «Caution» indicator lights up and the message

«Check Printer Mode» appears in the machine’s display. In this case, press

the [Printer] key to display the Printer mode screen.

The main error messages that appear in the Printer mode screen are de-

scribed below.

PAPER SIZE ERROR

NO SUITABLE PAPER

INCORRECT PAPER SIZE

PAPER EMPTY

MEDIA TYPE ERROR

MEMORY NEAR FULL

SECUREPRINT IS NOT

AVAILABLE

NOT ACCEPTED

PASSWORD

12-2

Cause

The size of paper specified

with the printer driver is differ-

ent from the size of paper

loaded in the paper drawer.

«Auto» is selected in the «Pa-

per Source» list in the printer

driver, but paper of the speci-

fied size is not loaded.

Paper of the size specified in

the printer driver is not loaded

in the specified paper drawer.

Either no paper is loaded in

the specified paper drawer or

the specified paper drawer is

not installed on the machine.

Paper of the type specified in

the printer driver is not loaded

in the specified paper drawer.

The image data received from

the computer has exceeded

the capacity of the memory.

Since the expanded memory

unit is not installed, the «Se-

cure Print» setting cannot be

selected.

Since the secure print pass-

word is incorrect, the docu-

ment cannot be printed.

Troubleshooting

Remedy

Pull open the paper drawer

with the size error, and then

close it again. Check if a cus-

tom paper size has been en-

tered, and correct the paper

size from Utility mode.

Load paper of the specified

size into a paper drawer.

Change the paper size from

Utility mode, and then load pa-

per of the appropriate size into

a paper drawer.

If the multi bypass tray (op-

tional) is used for printing,

printing begins when the ap-

propriate paper is loaded.

Load paper of the specified

size into the specified paper

drawer.

Load the appropriate paper

into a paper drawer, and then

change the paper type from

Utility mode.

If the multi bypass tray (op-

tional) is used for printing,

printing begins when the ap-

propriate paper is loaded.

Press any key.

Turn the machine off, then on

again.

The job is cancelled.

Type in the correct password.

IC-206

1. 11-18-2011

   
   

   #1

   Hello everybody,
   We have Bh163 in workshop with C0F33. We replaced drum and developer and after running ATDC adjustment the C0F33 appeared again. After turning off/on appeard C0F32. Then we changed ATDC sensor, but it was the same situation. We tried manually to adjust the ATDC gain but with no success. Any ideas? Thanks in advance.

   ---

2. 11-18-2011

   
   

   #2

   

   
   Technician
   

   

   ---

   Rep Power

   24

   Re: Bizhub 163 C0F33
   

   1. Make sure contacts are clean both on IU side and machine side.
   2. Make sure developer is being agitated.
   3. Change Printer Control Board.
   4. Change DC Power Unit.

   In my experience, either 1 or 2 are the most likely cause.
   Good Luck.

   ---

3. 11-18-2011

   
   

   #3

   

   
   Senior Tech
   

   100+ Posts

   

   

   ---

   Rep Power

   25

   Re: Bizhub 163 C0F33
   

   if that what you did dont solve the problem,
   Maybe you should try to change the PRCB..

   and if still error persist,
   check your wires/harnesses..

   ---

4. 11-18-2011

   
   

   #4

   Re: Bizhub 163 C0F33
   

   Thanks for help.
   Today we installed the problem IU on other Bh163 and after ATDC auto adjust the code was again C0F33. The contacts between AtDC sensor and coupling are OK. Is there any possibility the machine to damage ATDC sensor?

   ---

5. 11-18-2011

   
   

   #5

   

   
   Technician
   

   

   ---

   Rep Power

   24

   Re: Bizhub 163 C0F33
   

   Are you sure developing unit is agitating the developer?

   Did you have Error Code before you changed drum and developer?

   Try swapping developing unit from the other machine.

   I have never heard of a machine harming TDS but there is a possibility that the TDS you changed is faulty.

   ---

6. 11-22-2011

   
   

   #6

   

   
   Senior Tech
   

   100+ Posts

   

   

   ---

   Rep Power

   25

   Re: Bizhub 163 C0F33
   

   Agree!

   If contacts are okey, then probably its in the developing unit..
   try to find some other developing unit..

   But i have once encountered a malfunctioning ATDC sensor..
   Some point also to be check..

   ---