Paper size error oki

Сообщения об ошибке

— 149 —

Ус

тр

а

не

ни

е

неисправност

ей

7

Сообщения об ошибках для копирования

Следующие сообщения отображаются на экране отображения панели оператора, при использовании функции
копирования.

581

Please close faceup stacker.
581:Cannot print with duplex.

Мигает

Не смотря на попытку дуплексной печати, укладчик
лицевой стороной вверх открыт и дуплексная печать
отключна.

500

Please install paper on
Manual Feeder. Please set paper
(%MEDIA_SIZE%).
To cancel, select [Cancel]

Мигает

Необходима подача бумаги вручную. Вставьте
бумагу вручную, показанную %РАЗМЕР
НОСИТЕЛЯ%.

400

Paper Size Error
Please open the scanner unit and the top cover
and check paper size.

Please see Help for details.

Мигает

Используется бумага неподходящего размера.
Проверьте бумагу в лотке или проверьте на подачу
нескольких листов. Откройте и закройте крышку для
выполнения восстановления печати, и продолжайте.

347

Please install new Image Drum Unit.

Please see Help for details.

Мигает

Срок эксплуатации блока барабана переноса
изображений подходит к концу.

Decode error occurred.
Please check image data.

, чтобы закрыть

Загорается Произошла ошибка во время выполнения анализа

данных изображений, введенных из МПУ.
Для печати из USB памяти или интернет факса/
электронной почты/факса (с сохранением данных
связи), появится ошибка в анализе данных TIFF или
JPEG.

409

Please open the top cover.
409:Faceup Stacker Error

Мигает

Укладчик лицевой стороной вверх был задействован
во время печати, печать была остановлена и ошибка
была выпущена.

Код

ошибки

Сообщение

Кнопка

<STATUS

(СТАТУС)>

Причина/Способ устранения

Автономный режим

Загорается Устройство отключено от сети и запуск задания

копирования невозможен.
Нажмите кнопку <PRINT(ПЕЧАТЬ)> на панели
оператора, а затем выберите [Online/Offline] на
экране меню печати.

Вы хотите продолжить

Загорается

Сканирование для задания копирования
приостановлено из-за ошибки, но теперь ошибка
устранена.
Для запуска сканирования оставшихся документов,
установите документы в АПД, а затем выберите [Да].

Код

ошибки

Сообщение

Кнопка

<STATUS

(СТАТУС)>

Причина/Способ устранения

OK

Oki c822 toner sensor error

Причина в том, что принтер «не видит» прыгающей в своём окошке шторки датчика тонера (см. статью о механизме работы датчика). Есть пять простых вариантов причины возникновения этой проблемы:
1. Не до упора повёрнута ручка запирания тонер-картриджа. Окошко в торце ручки должно находиться строго напротив отверстия в корпусе принтера, за которым расположена оптопара датчика тонера. Нажмите ручку до упора.
2. На белую шторку, появляющуюся в окошке, налип тонер, отчего она перестаёт отражать свет оптопары. Шторку необходимо очистить от тонера, чтобы пропало сообщение об ошибке датчика.
3. В принтере, где уже побывал покупной картридж, оказался вновь стартовый. В комплекте поставки всех младших принтеров, начиная с лета 2004 года, идут стартовые тонер-картриджи, у которых нет датчика тонера (см. выше), а вместо него просто наклеен кусочек фольги. Такой картридж может нормально работать в принтере только с самого начала. При его наличии принтер считает расход тонера только по формуле и когда достчитывает до конца, требует заменить картридж. После этого в принтер необходимо установить покупной картридж, в котором есть датчик тонера. Как только такой картридж попадает в принтер, он переходит в режим контроля датчика тонера и если после этого в него опять вставить стартовый картридж, то принтер, не увидев работающего датчика, выдаст ошибку датчика тонера.
4. Размер окошка слишком велик. Возможна ситуация, когда окошко, за которым находится белая шторка, слишком велико и поэтому оптопара не может корректно сфокусировать отражение от шторки и получить устойчивое срабатывание. Исправить ситуацию можно следующим образом: необходимо заклеить чёрным не блестящим скотчем окошко сверху так, чтобы высота прорези была не более 4мм:

5. Установлен не тот фотокартридж. В нижней части фотокартриджа расположен небольшой металлический штифт (или несколько штифтов), которые попадают в прорези на металлической пластине, расположенной на правой части внутри принтера.

Штифты могут быть установлены в разные позиции. Именно положение штифтов определяет «совместимость» того или иного фотокартриджа с тем или иным принтером. Если в принтер вставлен фотокартридж не того типа, то картридж устанавливается в принтере не под нужным углом и окошко датчика тонера просто не попадает напротив оптопары. Штифт, в принципе, можно переставить, но для этого необходимо разобрать картридж, так как вынуть его наружу невозможно: на его конце находится шляпка, не позволяющая вытянуть его. Поэтому где-то эту причину тоже можно отнести к сложным вариантам. Впрочем, можно открутить металлическую пластину внутри принтера, ту самую, в которую упираются эти металлические штырьки, тогда в принтер можно будет установить печатный картридж от любого принтера 3000й или 5000й серии.

Теперь «сложные» варианты сами по себе. Вынув тонер-картридж и удерживая его в том же положении, как он стоит в принтере, покрутите пальцем шестерню снизу. Белая шторка должна периодически на короткое время убираться вверх из окошка. Если этого не происходит, значит возникла механическая проблема.
1. Заклинил рычажок датчика. Белая шторка застряла либо в верхнем либо в нижнем положении. Попробуйте вручную (например иголкой) раскачать шторку вверх и вниз. Обычно это можно сделать не разбирая картриджа.
2. Оторвалась мешалка внутри тонер-картриджа. При вращении шестерни мешалка не вращается внутри картриджа, отчего и шторка тоже не прыгает. Очевидно, что для восстановления работоспособности необходимо разобрать картридж и восстановить вращение мешалки.
3. В картридж засыпан магнитный тонер. О такой проблеме доводилось слышать только по отношению к чёрному картриджу, который пытались заправлять чёрным магнитным тонером от ч/б принтеров. Такой тонер, находящийся в картридже, «навсегда» притягивает к себе магнитик, отчего шторка уходит из своего окошка вверх, давая на датчике постоянное false. Решение очевидно – воспользоваться немагнитным тонером, тщательно вычистив внутренности тонер-картриджа от остатков магнитного порошка.

У новой серии принтеров С3000 и C5000 датчик тонера расположен в фотокартридже. Снаружи он виден как прямоугольное окошко, расположенное на торце фотокартриджа с той стороны, где располагается запирающая ручка тонер-картриджа:

Это окошко закрывается специальной шторкой, когда тонер-картридж отсоединяется от фотокартриджа (на рисунке ниже мигает красным, но на самом деле эта шторка — чёрная):

Так вот, ошибка датчика тонера может возникать на этих принтерах от того, что при закрывании ручки тонер-картриджа шторка не ушла наверх. В этом случае оптопара «не увидит» движущегося за окошком отражающего сектора, который и вызывает срабатывание оптопары. Соответственно, закрыть ручку тонер-картриджа до упора или если это не помогает, принять другие меры для того, чтобы эта шторка ушла вверх.

Источник

Oki c822 toner sensor error

mariam » 01:47 — 23.10.07

KudesNIK » 10:08 — 23.10.07

Гость » 10:33 — 23.10.07

До этого — печатали. Ошибка датчика синего тонера. Ничего особенного не делали, пару раз бумага застревала на ленте переноса, вытаскивала картриджи аккуратненько, извлекала бумагу и дальше печатала. Но это реально пару раз всего и было, и проблем не вызывало. Я конечно куплю сейчас новый картридж, и/или фотокартридж если проблема в нем, принтер очень нужен в рабочем состоянии и времени разбираться особенно нет, но все равно очень хочу понять что случилось и как быть в таких ситуциях. Заранее спасибо за помощь

KudesNIK » 16:04 — 23.10.07

Вариантов с этим датчиком несколько.
1. Не до конца закрыта ручка, запирающая тонер-картридж в драм-картридже.
2. При закрытии картриджа не полностью поднялась шторка, закрывающая отверстие для отражалки в драм-картридже.
3. На оптопару насыпался тонер и свет просто не проходит
У меня тут пара фоток есть, ща я их обработаю и в соответствующий FAQ положу для простоты восприятия.

Кстати, в FAQ фотки и пояснения к ним уже прицепил, так что желающие могут их там посмотреть.

mariam » 16:53 — 24.10.07

Слов нет, одни эмоции. С тех пор как принтер встал, приходили два разных мальчика-ремонтника (не ОКИ, у нас нет специализированного сервиса в городе), чесали репы, бормотали что-то про чипы. А я, после недолгого, но проникновенного рассматривания новых картинок в «соответствующем FAQ» (не пойму как ссылки добавлять, простите) у KudesNIKa, залезла, что-то интуитивно поковыряла в окошке датчика, почистила на всяк. случ. еще раз оптопару, закрыла крышку и на глазах у изумленной публики принтер заработал.

KudesNIK
Спасибо! Мы будем покупать принтеры А3 формата, и тот факт, что это будут OKI во многом определил тот факт, что у OKI есть такой замечательный KudesNIK Я теперь Ваша фанатка.

KudesNIK » 10:33 — 25.10.07

mariam , а в каком городе у нас сервис-центр отсутствует? Судя по IP-адресу ты пишешь из Казани. А в Казани есть сервис по OKI. Но IP-адрес вещь неверная, поэтому расскажи, в какую сторону надо развиваться?

А ссылки просто вставляются — надо нажать кнопку URL и добавить нужную ссылку в тег
» [url=http:\www.ссылка.ru] «, потом написать то, что должно появиться и снова нажать кнопку URL. Усё.

mariam » 12:30 — 25.10.07

В данный момент вещаю из г. Набережные Челны. Гипотетически сервис может и есть, но его никак не найти, мы честно и долго искали, с тех пор еще когда у нас старые ОКИ стояли. Опять же, теоретически Казань недалеко, но не тащиться же туда из-за мелких проблем. Картриджи и проч. заказываю через Инет и вожу Грузовозоффым, т.к. в городе в продаже тоже нету. Но, насколько мне известно, здесь не так много ОКИ вообще в городе, у нас два с5900, да еще пару мест всего знаю. Да и городишко малюсенький.

Источник

Error Message List

Wait a moment. Network initializing .

The network is being initialized.

Wait for a while until the machine connects to the network.

Checking File System

File system in the hard disk is being checked. Wait for a while.

Inspection is required. PU Flash Error

Turn the machine off, and then back on. If the same error occurs, contact your dealer.

Inspection is required. PU Communication Error

Turn the machine off, and then back on. If the same error occurs, contact your dealer.

Offline Mode

The machine is offline. Press the Online button to set it to [Online].

Data present.

Data remains unprinted.

Deleting data.

The job was cancelled or user is unauthorized.

Warming up.

The machine is adjusting the temperature of the fuser unit. Wait for a while.

Preparing .

Color registration and density are being adjusted. Wait for a while.

Updating firmware. Do not turn OFF the power.

The programs on the machine are being updated.

Do not turn the machine off until the update completes.

The machine automatically restarts after the update completes.

Toner Low.

The toner indicated on the screen is low. Have a new toner cartridge ready.

Waste Toner Full Replace with new Toner Cartridge.

Waste toner is full. Replace the toner cartridge with a new one.

C: Cyan (blue), M: Magenta (red)

C Non Recommended Toner.

An optimum C (Cyan, blue) toner cartridge is not installed.

Use a toner cartridge that matches your machine.

M Non Recommended Toner.

An optimum M (Magenta, red) toner cartridge is not installed.

Use a toner cartridge that matches your machine.

Y Non Recommended Toner.

An optimum Y (Yellow) toner cartridge is not installed.

Use a toner cartridge that matches your machine.

K Non Recommended Toner.

An optimum K (Black) toner cartridge is not installed.

Use a toner cartridge that matches your machine.

Error Postscript

A postscript error has occurred.

Image Drum Near Life.

The image drum indicated on the screen is near life. Have a new image drum ready.

C: Cyan (blue), M: Magenta (red), Y: Yellow, K: Black

Fuser Near Life.

The fuser unit is near life. Have a new fuser unit ready.

Belt Unit Near Life.

The belt unit is near life. Have a new belt unit ready.

Fuser Unit Life. Install New Fuser Unit.

The fuser unit reaches its lifetime.

Replace the fuser unit with a new one.

Belt Unit Life. Install New Belt Unit.

The belt unit reaches its lifetime.

Replace the belt unit with a new one.

Toner empty. Replace with new Toner Cartridge.

The toner indicated on the screen is empty. Replace the empty toner cartridge with a new one.

C: Cyan (blue), M: Magenta (red), Y: Yellow, K: Black

Toner cartridge not installed.

A color toner cartridge indicated on the screen is not installed.

Install the toner cartridge.

C: Cyan (blue), M: Magenta (red), Y: Yellow, K: Black

Image Drum Life. Please install new Image Drum Unit.

The image drum indicated on the screen reaches its lifetime.

Replace the image drum with a new one.

C: Cyan (blue), M: Magenta (red), Y: Yellow, K: Black

TRAY is empty.

No paper is loaded in the tray. Load paper.

File System is full.

Memory in the file system is full.

Delete unnecessary files.

The File System is write-protected.

The file you are trying to write is write-protected.

Check the file name.

Insufficient page memory to collate.

Insufficient memory error has occurred during collate printing.

Reduce the number of pages to print.

Insufficient memory. Error: 014

Memory full error has occurred during PC Fax reception. Press [Close].

Unauthorized user, job cancelled.

Unauthorized job was sent or unauthorized user attempted to print or send a fax. Data was deleted. Contact your administrator to use this machine.

File erasing .

Files stored for authentication print are being deleted.

Wait for a while.

Deleting encrypted authentication print data.

Files stored for encrypted authentication print are being deleted. Wait for a while.

Erased Data Full

Files supposed to be deleted are full. Erase the files.

Secure job storage period exceeded.

Files whose authentication print data storage period expired were automatically deleted.

Disk Read/Write Error

An error has occurred in the file system. Press [Close].

Flash Error

An error has occurred when firmware was being updated.

Contact the administrator.

Invalid print data received.

Invalid print data or PC fax data was received. To erase the message, press [Close].

If you performed authentication printing, the data was deleted because it was incomplete. Print again.

Received data has been discarded because Job Type is restricted.

Data whose job type is not defined in the acceptable job type settings was received. The data was discarded without being processed.

Select a job type defined in the acceptable job type settings for [Job Type] of the printer driver and print again.

Manual Request. Error : 500

Print on paper fed manually. Load paper in the MP tray.

Please change [MEDIA_SIZE] [MEDIA_TYPE] in [TRAY]. Error: 461, 462, 463, 464

The size and type of fed paper do not match those indicated on the screen. Use the same size and type of paper selected on the application.

Please change [MEDIA_SIZE] [MEDIA_TYPE] in MP Tray Error: 460

The size and type of paper loaded in the MP tray do not match those indicated on the screen. Make sure that the size and type of paper loaded in the MP tray match those selected on the application.

Wait a moment. Message Data processing .

Messages to be displayed on the machine are being updated. Wait for a while.

Wait a moment. Message Data writing .

Messages to be displayed on the machine are being updated. Wait for a while.

Restart the machine. Writing message data has been complete.

Messages to be displayed on the machine are now updated.

Turn the machine off, and then back on.

Wait for a while.

Please check data. Message Data Write Error

Updating messages to be displayed on the machine failed.

Make sure that you use right data for this machine.

Wait a moment. Network Configuration writing .

Network settings for this machine is changed. The new settings are being stored. Wait for a while.

Wait a moment. Network initializing .

Network settings for this machine are initializing.

Paper [TRAY] is empty Set [MEDIA_SIZE] Error: 490, 491, 492, 493, 494

No paper is loaded in the indicated tray. Load paper of the displayed size.

[TRAY] cassette is missing. Open and Close the indicated cassette. Error: 440, 441, 442, 430, 431, 432, 433

The tray is not installed. Install the cassette. If the cassette is already inserted, pull it out, and then insert it again.

Insufficient memory. Error: 420

Data is too complicated. Memory full error has occurred during processing. Reduce the volume of the print data.

Waste Toner Full Replace with new Toner Cartridge. Error: 414, 415, 416, 417

Waste toner of the toner cartridge is full. Opening and closing the front cover can resume printing for a while, but it may damage the image drum. Replace the toner cartridge with a new one as soon as possible.

C: Cyan (blue), M: Magenta (red)

Toner empty. Replace with new Toner Cartridge. Error: 410, 411, 412, 413

The indicated cartridge ran out of toner.

Opening and closing the front cover can resume printing for a while, but it may damage the image drum. Replace the toner cartridge with a new one as soon as possible.

C: Cyan (blue), M: Magenta (red), Y: Yellow, K: Black

Incompatible C Toner. Error: 552, 556, 616, 622

The installed C (Cyan, blue) toner cartridge is not optimum.

We recommend using an optimum toner cartridge.

Incompatible M Toner. Error: 551, 555, 615, 621

The installed M (Magenta, red) toner cartridge is not optimum.

We recommend using an optimum toner cartridge.

Incompatible Y Toner. Error: 550, 554, 614, 620

The installed Y (Yellow) toner cartridge is not optimum.

We recommend using an optimum toner cartridge.

Incompatible K Toner. Error: 553, 557, 617, 623

The installed K (Black) toner cartridge is not optimum.

We recommend using an optimum toner cartridge.

Toner Not Installed. Error: 610, 611, 612, 613

A color toner cartridge indicated on the screen is not installed.

Install the toner cartridge.

C: Cyan (blue), M: Magenta (red), Y: Yellow, K: Black

Image Drum Sensor Error Check Image Drum. Error: 540, 541, 542, 543

The sensor error has occurred in the image drum indicated on the screen.

Uninstall the image drum, and then install it again.

If the message persists, uninstall the toner cartridge and install it again.

If the toner cartridge is not installed, install it.

C: Cyan (blue), M: Magenta (red), Y: Yellow, K: Black

Multiple sheets of paper have been fed. Reset Paper in [TRAY]. Error: 401

The indicated tray fed multiple sheets of paper at a time.

Remove the cassette from the tray, and then load paper again.

Paper Size Error. Reset Paper in [TRAY]. Error: 400

Paper size error has occurred in the indicated tray. Make sure that the size made by paper loaded in the tray matches the setting made by the paper size dial in the paper cassette. Load paper according to the paper size and direction set for the paper size dial.

If the setting made by the paper size dial is wrong, cancel printing first, set the paper size dial, and then print again.

Make sure that the cassette does not feed multiple sheets of paper at a time after starting printing. If it happens, remove paper, and then load paper correctly.

Paper jam has occurred. Open the front cover and remove the paper. Error: 390

Paper jammed via the paper feed path from the MP tray.

If the edge of the jammed paper is not visible, open the front cover and remove the paper.

Paper jam has occurred. Pull out the [TRAY] cassette and then remove the paper. Error: 391, 392, 393, 394

A paper jammed via the paper feed path from the indicated tray.

Pull out the cassette, and then remove paper. If multiple sheets of paper are fed at a time, remove paper and reload paper.

Make sure that the paper stoppers are set in the right position.

Paper jam has occurred. Open the front cover and remove the paper. Error: 372, 380

Paper jammed in the paper feed path of the machine. Open the front cover and remove the jammed paper.

A paper jam has occurred under the image drum or around the fuser unit. Please remove paper. Error: 381, 382, 383, 348, 389

A paper jam has occurred inside the machine.

Open the cover and remove jammed paper.

A Paper Jam has occurred and paper remains near the Duplex Unit. Please remove paper. Error: 370, 371, 373

Paper jammed near the duplex printing unit.

Pull out the duplex unit on the back of the machine, and then remove jammed paper.

The 2-Sided Printing unit is not set correctly. Error: 360

The duplex unit is not properly installed. Install the duplex unit.

Image Drum Life. Please install new Image Drum Unit. Error: 350, 351, 352, 353

The image drum indicated on the screen reaches its lifetime.

Replace the image drum with a new one.

Opening and closing the cover can resume printing for a while. Replace with a new one as soon as possible, however.

C: Cyan (blue), M: Magenta (red), Y: Yellow, K: Black

Image Drum Life. Please install new Image Drum Unit. Error: 560, 561, 562, 563, 564, 565, 566, 567

The image drum indicated on the screen reaches its lifetime.

Replace the image drum with a new one.

C: Cyan (blue), M: Magenta (red), Y: Yellow, K: Black

Image Drum Life. Please install new Image Drum Unit. Error: 680, 681, 682, 683

Printing has stopped because the image drum indicated on the screen reached its lifetime. Replace with a new image drum to print.

C: Cyan (blue), M: Magenta (red), Y: Yellow, K: Black

Fuser Unit Life. Install New Fuser Unit. Error: 354

The fuser unit reaches its lifetime.

Replace the fuser unit with a new one.

Opening and closing the cover can resume printing for a while. Replace with a new one as soon as possible for maintaining the print quality.

Belt Unit Life. Install New Belt Unit. Error: 355

The belt unit reaches its lifetime.

Replace the belt unit with a new one.

Opening and closing the cover can resume printing for a while. Replace with a new one as soon as possible for maintaining the print quality.

The Fuser Unit is not installed correctly. Reset Fuser Unit. Error: 348

The fuser unit is not properly installed. Remove and re-install the fuser unit. If the error persists after re-installing, replace the fuser unit with a new one.

Waste Toner Full. Install New Belt Unit. Error: 356

Waste toner of the belt unit is full. Replace the belt unit with a new one. Opening and closing the cover can resume printing. Printing stops after 500 sheets are printed.

Toner cartridge not properly installed. Error: 544, 545, 546, 547

A color toner cartridge indicated on the screen is not installed.

Make sure that the lever on the toner cartridge is fully turned and the protective tape is removed.

C: Cyan (blue), M: Magenta (red), Y: Yellow, K: Black

Image Drum not properly installed. Check Image Drum. Error: 340, 341,342, 343

The indicated image drum is not installed correctly.

Remove and re-install the image drum.

C: Cyan (blue), M: Magenta (red), Y: Yellow, K: Black

The Fuser Unit is not installed correctly. Reset Fuser Unit. Error: 320

The fuser unit is not properly installed. Remove and re-install the fuser unit.

Belt Unit not installed correctly. Re-set the Belt Unit. Error: 330

The belt unit is not properly installed. Remove and re-install the belt unit.

[COVER] Open. Error: 310, 311, 587

Indicated cover is open. Close the cover.

Error: 310 The output tray, 311 The front cover, 587 The upper output tray

Please check data. Program Data Write Error

An error occurred when firmware was being updated.

Use a correct update file.

Power OFF/ON

Turn the machine off, and then back on.

If the same error occurs, contact your dealer.

Inspection is required.

Turn the machine off, and then back on.

If the same error occurs, contact your dealer.

Cancelling .

The cancel button was pressed while copying. The copy job is being cancelled. Wait for a while.

Automatic document feeder (ADF) cover is open.

The ADF cover of the scanner is open. Close the cover.

Document jam has occurred. Open the automatic document feeder (ADF) cover on the scanner to check.

Paper jammed in the ADF of the scanner.

Open the ADF cover and remove jammed paper.

Multiple sheets of document have been fed. Open the automatic document feeder (ADF) cover on the scanner to check.

Multiple sheets of document have been fed. Fan a stack of the paper well and place them on the automatic document feeder (ADF). Use the document glass if a tag or label is affixed to the document.

Scanner lamp error check the lamp.

Light volume of the scanner is low. Contact your dealer.

Power OFF/ON Carriage Error

An error has occurred on the carriage of the scanner. Turn the machine off, and then back on.

If the same error occurs, contact your dealer.

USB Memory Full

Scan To USB Memory was cancelled because the USB Memory is full.

Check the free space in the USB Memory.

Writing to USB memory failed.

The USB Memory is write-protected. Unlock the protection.

USB Memory disconnected.

The USB Memory was removed while performing Scan To USB Memory.

Connect to PC failed.

No destination computer was found for Scan to Computer. Make sure that your computer is turned on and recordable.

To erase the message, press [Close].

Insufficient memory occurred during Rx.

Memory full error has occurred during fax reception. Ensure available memory.

Communication Error

An error has occurred during fax transmission or fax reception.

Telephone

The external phone is in use.

File Transmission Error

An error such as a malfunction of the server or disconnection of a network cable has occurred while performing Scan To shared folder.

Check the network connection.

To erase the message, press [Close].

E-mail Transmission Error

An error such as a malfunction of the server or disconnection of a network cable has occurred while performing Scan To E-mail. Check the network connection.

To erase the message, press [Close].

Please check SMTP settings.

Cannot connect to the SMTP server. Check the network settings.

Please check POP3 settings.

Cannot connect to the POP3 server. Check the network settings.

SMTP Login failed.

An attempt to log into the SMTP server ended up an authentication error.

Check the network settings.

SMTP Auth. Unsupported

The SMTP server does not support the authentication system.

Check the network settings.

POP3 Login failed.

An attempt to log into the POP3 server ended up an authentication error.

Check the network settings.

Getting target IP failed. Please Check DHCP settings.

The DHCP server cannot be detected. Check the network connection.

Please check DNS settings.

Cannot connect to the DNS server. Check the network connection.

Please check Server settings.

Cannot connect to the file server. Check the network settings.

Server Login failed.

Logging into the file server failed. Check the server settings.

Entering directory failed.

Connecting to the directory of the FTP server failed. Check the server settings.

Changing data Transfer Type failed.

File transmission failed because the file transfer type was not accepted by the FTP server. Change the FTP transfer type to «binary».

File writing failed.

Files sent using Scan To shared folder could not be written. Check the access rights for the shared folder.

FTP destination Full.

Memory in the FTP server is low. Delete unnecessary files and ensure the free space.

Please change File Name.

The specified file name is not acceptable. Check the FTP server settings and change the file name.

Device communication protocol not supported.

The server does not support CIFS or FTP. Check the server settings.

Please check Network Share Name.

The name of the network shared folder is not correct. Check the folder name.

Please check data. Program Data Write Error

An error has occurred when program was being updated.

Please insert USB Memory.

Scan To USB Memory or print from USB Memory with USB Memory not inserted was attempted.

Insert USB Memory.

[TRAY] cassette missing.

The cassette in the indicated tray is pulled out.

Install the cassette.

Access Limitation Error Monochrome printing was performed due to the color printing limitation.

A color print job was converted to a mono print job due to an unauthorized user. Contact your administrator for color printing.

Access Limitation Error Data was deleted due to the color printing limitation.

A color print job was deleted due to an unauthorized user. Contact your administrator for color printing.

Restricted access error Data deleted due to printing restrictions.

A print job was deleted due to an unauthorized user. Contact your administrator for printing.

Incompatible USB device connected. Remove the connected USB device.

An unsupported USB device is connected. Remove the USB device.

Please remove the connected USB device. USB device has not been recognized.

The connected USB device was not recognized. Remove the USB device.

Please remove the USB Hub. USB Hub is connected.

A USB hub is connected. Remove the USB hub. This machine does not support USB hub.

Inspection is required. SIP Error

Turn the machine off, and then back on. If the same error occurs, contact your dealer.

Please call service. Scanner unit failed to detect printer unit.

Turn the machine off, and then back on. If the same error occurs, contact your dealer.

HDD Error 0

While initializing this machine, a hard disk which needs formatting was detected.

HDD Error 250

While initializing this machine, a damaged file for encrypted authentication printing was found. Format the hard disk again.

Accounting Log buffer is near full.

The accounting log buffer is almost full.

Acquire the log and free the buffer.

Accounting Log Writing Error

An accounting log writing error has occurred.

To erase the message, press [Close].

Job Log Database Error

A data base access error has occurred while writing or reading the job log. Turning the machine off and on may resolve the problem.

To erase the message, press [Close].

Accounting Log Buffer Full (Delete old logs)

Old logs were deleted, because accounting log buffer was full. Acquire the log and free the buffer.

Power OFF/ON

Turn the machine off, and then back on. If the same error occurs, contact your dealer.

A decoding error occurred. Check the image data.

An error has occurred in the image data sent to this machine. Check the image data.

Process has been canceled as there is no space on the device. Please free up enough memory space by reducing usage and try again.

Processing data was cancelled due to memory full.

Reduce the usage on the device to ensure available memory, and then retry.

Process has been canceled by a device error. After maintenance or change of the device, please try again.

Processing data was cancelled because an error occurred on the device.

Repair or replace the device, and then retry.

Access denied to PC. Please check PC.

Connecting to a computer failed when performing Scan to Computer. Check the settings on the computer.

Deleting data.

This machine ran out of color toner. Color print data is being deleted.

Error PDF

The PDF file is damaged.

This PDF file is password protected.

This PDF file is password protected. Enter a password to print.

Valid password required to print document.

This PDF needs authentication. Enter a password to print.

No communication with the SNTP server.

Obtaining current time from the SNTP server failed. Check the server.

USB Memory disconnected.

The USB Memory was removed while printing from USB Memory. Do not remove USB Memory while printing is in progress.

Cannot open the file.

The specified file could not be Opened. Check the file.

Cannot read the file.

Files could not be read. Check the device where the files are stored.

File loading from USB.

Data is being read from USB Memory.

Press the Stop button to cancel reading.

An error occurred. Scanning is pending.

Printing has stopped due to an error.

Image Drum Sensor Error.

The toner sensor error has occurred in the image drum indicated on the screen.

Printing was stopped. Rear Output Tray was opened during printing. Open the Output Tray. Error code: 409

The rear output tray was moved while printing.

Place the rear output tray in the correct position, and then open and close the output tray.

Toner empty. Replace with new Toner Cartridge.

The indicated cartridge ran out of toner.

Replace the empty toner cartridge with a new one.

Wait Timeout in menu is disabled. Printing is disabled except by USB. Clear page buffer and enable time out in menu.

Wait Timeout is disabled.

Insufficient memory occurred during Fax Tx reservation.

Insufficient memory error has occurred during Scan To fax.

Insufficient memory.

Insufficient memory error has occurred during fax reception.

E-mail receiving has been cancelled.

E-mail reception was cancelled.

Check the file format and size of the attached file.

Wireless settings are incomplete.

Wrong values are set or items remain unset in the wireless LAN settings. Check the wireless settings.

Not connected to wireless access point.

No wireless LAN access points are found.

Make sure that the access point is turned on.

Disconnect and re-connect to wireless LAN.

Wireless startup failed.

Restart the machine. If the error persists, contact your dealer.

Firmware Update Error Please try again. If network doesn’t work, please try firmware update over USB.

Updating the firmware failed. Update again.

Registering with Google Cloud Print. Don’t turn off the power until registration is complete.

This machine is being registered to the Google Cloud Print service. Wait for a while.

Deleting from Google Cloud Print.

This machine is being removed from the Google Cloud Print service. Wait for a while.

Caution, unknown Consumable detected Go to User Manual «Trouble Shooting» to restore operation Error 709

You can use any consumables in your product, but you must accept the risks of using non-genuine consumables.

If the use of non-genuine consumables causes damage to the product or results in your product not functioning to its full specification, then such damage or effect on the product is not covered by warranty.

To accept these risks and to restore function;

Turn off the machine.

Holding the [CLEAR] button, turn on the machine.

Release the [CLEAR] button when «RAM CHECK 100%» is displayed.

This operation log is recorded in the product.

If you have any questions, contact your dealer.

Replace the image drum. [PAGES] Pages Left.

The image drum indicated on the screen reaches its lifetime.

Replace the image drum with a new one.

C: Cyan (blue), M: Magenta (red), Y: Yellow, K: Black

Replace the image drum. Print Quality Not Guaranteed.

The image drum indicated on the screen reaches its lifetime.

Replace the image drum with a new one.

C: Cyan (blue), M: Magenta (red), Y: Yellow, K: Black

Receiving data timeout.

Data could not received within a certain period of time.

IPv4 address is conflicted. Please change IPv4 address.

The IP address assigned to this machine is duplicated with that of another device.

Check the IP addresses, and then assign another IP address.

Incompatible [COLOR] Image Drum. Error: 984, 685, 686, 687, 690, 691, 692, 693, 700, 701, 702, 703, 704, 705, 706, 707

Non-optimum image drum is installed.

C: Cyan (blue), M: Magenta (red), Y: Yellow, K: Black

C Image Drum Not Installed. Error: 696

Cyan (blue) image drum is not installed.

Install the image drum.

M Image Drum Not Installed. Error: 695

Magenta (red) image drum is not installed.

Install the image drum.

Y Image Drum Not Installed. Error: 694

Yellow image drum is not installed.

Install the image drum.

K Image Drum Not Installed. Error: 697

Black image drum is not installed.

Install the image drum.

Blank pages were detected on all pages. Please check how the document was set.

Scanned pages are all blank. Turn over the document.

In order to set paper that cannot be output to the Upper Output Tray, the paper was output from Output Tray. To turn off this display, press the [Close] button.

Check the type of the specified paper.

Simplex printing was performed as the paper setting did not allow duplex printing.

Duplex printing is not available on the specified paper.

Check the size and thickness of paper.

Multi-purpose tray has not been set to be used as the tray, so multiple copies have been printed. Please verify multi-purpose tray settings. Press [Close] button to remove this dialog

MP tray setting is set to [Do Not Use]. Change the MP tray setting.

Output Paper Full. Remove the paper on [TRAY]. Error: 480, 485

Paper in the output tray is full.

Remove the handout.

Changing Language. Panel operation is disabled.

Display language is being changed.

Wait for a while.

Language Change Failed. Error num: %CODE%

Switching display languages failed. Press the power button to turn the machine off, and then back on.

Detected an abnormality of internal database. The data must be deleted. After pressing [Format], the data will be deleted, and then reboot.

Data base is beyond restoration.

To delete the data base, press [Format].

Cannot print because your Summary Account balance is 0. User name for Printing: [USERNAME] Summary Account Name for Insufficient Balance: [ACCOUNTNAME] To continue the print job, increase the balance and select [Start]. To increase the balance, please contact the device administr. To cancel the print job, select [Cancel].

The number of print jobs excesses the limit. No more print jobs are authorized. Contact your administrator.

Copyright © 2015 Oki Electric Industry Co., Ltd. All rights reserved.

Источник