Port link type access error please renew the default configurations

How to change the link type of an interface

Описание проблемы

How to change the link type of an interface

Решение

The link type of an interface can be access, trunk, hybrid, or Dot1q-tunnel. The methods used to change the link type of an interface in different versions are different.
In V200R005 and later versions, run the port link-type { access | trunk | hybrid | dot1q-tunnel } command and enter y or n as prompted. When the interface uses the default VLAN configuration, the system does not display any message. The link type of the interface is changed directly.
When you enter y and press Enter, the device automatically deletes the non-default VLAN configuration of the interface and sets the link type of the interface to the specified one.
When you enter n and press Enter, the device retains the current link type and VLAN configuration of the interface.
Change the link type of the interface to hybrid.
<HUAWEI> system-view
[HUAWEI] interface GigabitEthernet0/0/1
[HUAWEI-GigabitEthernet0/0/1] port link-type hybrid
Warning: This command will delete VLANs on this port. Continue?[Y/N]:y
Info: This operation may take a few seconds. Please wait for a moment…done. In earlier versions of V200R005, an interface joins VLAN 1 by default, and the PVID of an interface is VLAN 1. You can run the port link-type { access | trunk | hybrid | dot1q-tunnel } command to change the link type of the interface.
Change the link type of the interface to access.

<HUAWEI> system-view
[HUAWEI] interface GigabitEthernet0/0/1
[HUAWEI-GigabitEthernet0/0/1] port link-type access
[HUAWEI-GigabitEthernet0/0/1] port default vlan 10
Change the link type of the interface to trunk.

<HUAWEI> system-view
[HUAWEI] interface GigabitEthernet0/0/1
[HUAWEI-GigabitEthernet0/0/1] port link-type trunk
[HUAWEI-GigabitEthernet0/0/1] port trunk pvid vlan 10
[HUAWEI-GigabitEthernet0/0/1] port trunk allow-pass vlan 2 10 20
Change the link type of the interface to hybrid.

<HUAWEI> system-view
[HUAWEI] interface GigabitEthernet0/0/1
[HUAWEI-GigabitEthernet0/0/1] port link-type hybrid
[HUAWEI-GigabitEthernet0/0/1] port hybrid pvid vlan 10
[HUAWEI-GigabitEthernet0/0/1] port hybrid untagged vlan 2 10
[HUAWEI-GigabitEthernet0/0/1] port hybrid tagged vlan 20
Change the link type of the interface to Dot1q-tunnel.

<HUAWEI> system-view
[HUAWEI] interface GigabitEthernet0/0/1
[HUAWEI-GigabitEthernet0/0/1] port link-type dot1q-tunnel
[HUAWEI-GigabitEthernet0/0/1] port default vlan 10
When you change the link type of an interface that does not use the default VLAN configuration, the system displays the message «Error: Please renew the default configurations.»

You need to restore the default configuration of the interface, and then change the link type of the interface.

Restore the default VLAN configuration of an access or Dot1q-tunnel interface.
<HUAWEI> system-view
[HUAWEI] interface gigabitethernet 0/0/1
[HUAWEI-GigabitEthernet0/0/1] undo port default vlan
Restore the default VLAN configuration of a trunk interface.
<HUAWEI> system-view
[HUAWEI] interface gigabitethernet 0/0/1
[HUAWEI-GigabitEthernet0/0/1] undo port trunk pvid vlan
[HUAWEI-GigabitEthernet0/0/1] undo port trunk allow-pass vlan all
[HUAWEI-GigabitEthernet0/0/1] port trunk allow-pass vlan 1
Restore the default configuration of a hybrid interface.
<HUAWEI> system-view
[HUAWEI] interface gigabitethernet 0/0/1
[HUAWEI-GigabitEthernet0/0/1] undo port hybrid pvid vlan
[HUAWEI-GigabitEthernet0/0/1] undo port hybrid vlan all
[HUAWEI-GigabitEthernet0/0/1] port hybrid untagged vlan 1

Источник

Содержание

  1. Port link type access error please renew the default configurations
  2. This document describes the CLI-based configurations of universal protocols and common features for Huawei switches on basic networks.
  3. Changing the Link Type of an Interface
  4. Вопрос со свитчем HUAWEI S2326TP-IE
  5. Рекомендованные сообщения
  6. Создайте аккаунт или войдите в него для комментирования
  7. Создать аккаунт
  8. Войти
  9. Сейчас на странице 0 пользователей
  10. Похожие публикации
  11. How to change the link type of an interface
  12. Описание проблемы
  13. Решение

Port link type access error please renew the default configurations

Your browser version is too early. Some functions of the website may be unavailable. To obtain better user experience, upgrade the browser to the latest version.

Enterprise products, solutions & services

This document describes the CLI-based configurations of universal protocols and common features for Huawei switches on basic networks.

Changing the Link Type of an Interface

Change the link type of the interface to access.

Change the link type of the interface to trunk.

Change the link type of the interface to hybrid.

Change the link type of the interface to Dot1q-tunnel.

When you change the link type of an interface that does not use the default VLAN configuration, the system displays the message «Error: Please renew the default configurations.»

You need to restore the default configuration of the interface, and then change the link type of the interface.

  • Restore the default VLAN configuration of an access or Dot1q-tunnel interface.
  • Restore the default VLAN configuration of a trunk interface.
  • Restore the default configuration of a hybrid interface.

Источник

Вопрос со свитчем HUAWEI S2326TP-IE

Автор: Emiresik,
2015-07-30 12:00:42 в Коммутаторы L2

Рекомендованные сообщения

Создайте аккаунт или войдите в него для комментирования

Вы должны быть пользователем, чтобы оставить комментарий

Создать аккаунт

Зарегистрируйтесь для получения аккаунта. Это просто!

Войти

Уже зарегистрированы? Войдите здесь.

Сейчас на странице 0 пользователей

Нет пользователей, просматривающих эту страницу.

Похожие публикации

Switch Huawei S5735-L32ST4X-A1 24x GE SFP, 8x 10/100/1000BASE-T, 4x 10GE SFP+, AC power

новые, есть несколько шт.

Есть от провайдера блок реальных адресов, к примеру 100.1.1.192/26

Раньше сеть была в одном влане и записи в /etc/rc.conf были такие:

ifconfig_ix0=»inet 192.168.0.1 netmask 255.255.255.0″ # Шлюз для пользователей с локальным IP ifconfig_ix0_alias0=»inet 100.1.1.193 netmask 255.255.255.192″ # Шлюз для пользователей с реальными IP
После чего стала задача часть пользователей переводить во вланы тоже с разделением на локальные IP и реальные, первый влан создал где-то пару лет назад и все работает:

ifconfig_vlan1=»vlan 1 vlandev ix0 192.168.1.1 netmask 255.255.255.0″ # Шлюз для пользователей с локальным IP во Влане 1 ifconfig_vlan1_alias0=»inet 100.1.1.248 netmask 255.255.255.248″ # Шлюз для пользователей с реальными IP во Влане 1
И вот стоит задача создать еще один влан, делаю по аналогии с вланом 1, только маску смещаю назад:

ifconfig_vlan1=»vlan 1 vlandev ix0 192.168.1.1 netmask 255.255.255.0″ # Шлюз для пользователей с локальным IP во Влане 2 ifconfig_vlan1_alias0=»inet 100.1.1.246 netmask 255.255.255.254″ # Шлюз для пользователей с реальными IP во Влане 2
Когда я вношу это в /etc/rc.conf и прописал команду:

ifconfig vlan2 create
Все заработало.

Но как только перезагрузился сервер, перестали работать реальные IP без вланов, в первом влане и во втором. Не пойму что не так делаю, возможно я с маской подсети что-то недопонимаю.

Источник

How to change the link type of an interface

Дата выпуска: 2016-11-24 | Просмотры: 86996 | Загрузки: 0 | № документа: EKB1000384086

Описание проблемы

Решение

The link type of an interface can be access, trunk, hybrid, or Dot1q-tunnel. The methods used to change the link type of an interface in different versions are different.
In V200R005 and later versions, run the port link-type < access | trunk | hybrid | dot1q-tunnel >command and enter y or n as prompted. When the interface uses the default VLAN configuration, the system does not display any message. The link type of the interface is changed directly.
When you enter y and press Enter, the device automatically deletes the non-default VLAN configuration of the interface and sets the link type of the interface to the specified one.
When you enter n and press Enter, the device retains the current link type and VLAN configuration of the interface.
Change the link type of the interface to hybrid.
system-view
[HUAWEI] interface GigabitEthernet0/0/1
[HUAWEI-GigabitEthernet0/0/1] port link-type hybrid
Warning: This command will delete VLANs on this port. Continue?[Y/N]:y
Info: This operation may take a few seconds. Please wait for a moment. done. In earlier versions of V200R005, an interface joins VLAN 1 by default, and the PVID of an interface is VLAN 1. You can run the port link-type < access | trunk | hybrid | dot1q-tunnel >command to change the link type of the interface.
Change the link type of the interface to access.

system-view
[HUAWEI] interface GigabitEthernet0/0/1
[HUAWEI-GigabitEthernet0/0/1] port link-type access
[HUAWEI-GigabitEthernet0/0/1] port default vlan 10
Change the link type of the interface to trunk.

system-view
[HUAWEI] interface GigabitEthernet0/0/1
[HUAWEI-GigabitEthernet0/0/1] port link-type trunk
[HUAWEI-GigabitEthernet0/0/1] port trunk pvid vlan 10
[HUAWEI-GigabitEthernet0/0/1] port trunk allow-pass vlan 2 10 20
Change the link type of the interface to hybrid.

system-view
[HUAWEI] interface GigabitEthernet0/0/1
[HUAWEI-GigabitEthernet0/0/1] port link-type hybrid
[HUAWEI-GigabitEthernet0/0/1] port hybrid pvid vlan 10
[HUAWEI-GigabitEthernet0/0/1] port hybrid untagged vlan 2 10
[HUAWEI-GigabitEthernet0/0/1] port hybrid tagged vlan 20
Change the link type of the interface to Dot1q-tunnel.

system-view
[HUAWEI] interface GigabitEthernet0/0/1
[HUAWEI-GigabitEthernet0/0/1] port link-type dot1q-tunnel
[HUAWEI-GigabitEthernet0/0/1] port default vlan 10
When you change the link type of an interface that does not use the default VLAN configuration, the system displays the message «Error: Please renew the default configurations.»

You need to restore the default configuration of the interface, and then change the link type of the interface.

Restore the default VLAN configuration of an access or Dot1q-tunnel interface.
system-view
[HUAWEI] interface gigabitethernet 0/0/1
[HUAWEI-GigabitEthernet0/0/1] undo port default vlan
Restore the default VLAN configuration of a trunk interface.
system-view
[HUAWEI] interface gigabitethernet 0/0/1
[HUAWEI-GigabitEthernet0/0/1] undo port trunk pvid vlan
[HUAWEI-GigabitEthernet0/0/1] undo port trunk allow-pass vlan all
[HUAWEI-GigabitEthernet0/0/1] port trunk allow-pass vlan 1
Restore the default configuration of a hybrid interface.
system-view
[HUAWEI] interface gigabitethernet 0/0/1
[HUAWEI-GigabitEthernet0/0/1] undo port hybrid pvid vlan
[HUAWEI-GigabitEthernet0/0/1] undo port hybrid vlan all
[HUAWEI-GigabitEthernet0/0/1] port hybrid untagged vlan 1

Источник

Источник

Last Update:2016-12-28
Source: Internet

Author: User

When I recently tried to change the interface of the Huawei s2300-52p switch from the previous trunk to access, the changes were unsuccessful and the error message was as follows:

650) this.width=650; «src=»/e/u261/themes/default/images/spacer.gif «style=» Background:url («/e/u261/lang/zh-cn/ Images/localimage.png «) no-repeat center;border:1px solid #ddd;» alt= «Spacer.gif»/>

[Zgk-bg-ethernet0/0/6]dis This

#

Interface ETHERNET0/0/6

Port Link-type Trunk

Port Trunk Allow-pass VLAN 2 to 4094

Loopback-detect Enable

#

Return

[Zgk-bg-ethernet0/0/6]port link-t

[Zgk-bg-ethernet0/0/6]port link-type Access

Error:please Renew the default configurations.

… …

[Zgk-bg-ethernet0/0/6]undo Port Link-type Trunk

^

Error:too many parameters found at ‘ ^ ‘ position.

[Zgk-bg-ethernet0/0/6]undo Port Link-type

Error:please Renew the default configurations.

[ZGK-BG-ETHERNET0/0/6]

Regardless of configuration, you cannot change the port trunk to access

After this configuration is found, you can change the port:

[Zgk-bg-ethernet0/0/6]dis This

#

Interface ETHERNET0/0/6

Port Link-type Trunk

Port Trunk Allow-pass VLAN 2 to 4094

Loopback-detect Enable

#

Return

[ZGK-BG-ETHERNET0/0/6] undo Port Trunk Allow-pass VLAN all

Info:this operation may take a few seconds. Please wait for a moment…done.

[ZGK-BG-ETHERNET0/0/6] Port trunk allow-pass VLAN 1

Info:this operation may take a few seconds. Please wait for a moment…done.

[Zgk-bg-ethernet0/0/6]port link-type Access

[Zgk-bg-ethernet0/0/6]dis This

#

Interface ETHERNET0/0/6

Port Link-type Access

Loopback-detect Enable

#

Return

Success!

Go first to enable all VLANs through the port and then re-add the default VLAN 1 through, then you can change the port type!

This article from the «full of strokes, modest benefits!» «Blog, be sure to keep this provenance http://lanfenggo.blog.51cto.com/6322019/1886836

Huawei switch changes port from trunk to access error resolution

Источник

Рассмотрим основные команды для настройки vlan, особенности конфигурирования интерфейсов в разных режимах работы — access, trunk и hybrid на коммутаторах серии huawei quidway S2300 и S5300.

Создание и удаление vlan на коммутаторах huawei

Создание vlan на коммутаторах huawei

[huawei] vlan {vlan-id}

Пример:

system-view
[huawei] vlan 150
[huawei-vlan150] quit
[huawei]

Удаление vlan на коммутаторах huawei

[huawei] undo vlan {vlan-id}

Настройка портов коммутаторов huawei в режиме acess port

В режиме конфигурирования интерфейса задем тип — access.

[huawei-GigabitEthernet0/0/1] port link-type access

Задаем номер vlan, по умолчанию на порту используется vlan-id = 1.

[huawei-GigabitEthernet0/0/1] port default vlan {vlan-id}

Пример:

[huawei] interface GigabitEthernet 0/0/1
[huawei-GigabitEthernet0/0/1] port link-type access
[huawei-GigabitEthernet0/0/1] port default vlan 150
[huawei-GigabitEthernet0/0/1] quit

Настройка портов коммутаторов huawei в режиме trunk port

В режиме конфигурирования интерфейса задем тип — trunk.

[huawei-GigabitEthernet0/0/1] port link-type trunk

Добавляем номера vlan в trunk через пробел или диапазон vlan используя to (Пример 100 to 200).

[huawei-GigabitEthernet0/0/1] port trunk allow-pass vlan {vlan-id1 vlan-id2 ... vlan-idn}

При необходимости можно изменить и default vlan (нетегированную) на другую.

[huawei-GigabitEthernet0/0/1] port trunk pvid vlan {vlan-id}

Пример:

[huawei] interface GigabitEthernet 0/0/1
[huawei-GigabitEthernet0/0/1] port link-type trunk
[huawei-GigabitEthernet0/0/1] port trunk allow-pass vlan 150 200 to 220
[huawei-GigabitEthernet0/0/1] port trunk pvid vlan 150
[huawei-GigabitEthernet0/0/1] quit

Настройка портов коммутаторов huawei в режиме hybrid port

В режиме конфигурирования интерфейса задем тип — hybrid.

[huawei-GigabitEthernet0/0/1] port link-type hybrid

Добавляем номера тегированных vlan.

[huawei-GigabitEthernet0/0/1] port hybrid tagged vlan {vlan-id1 vlan-id2 ... vlan-idn}

Добавляем номера нетегированных vlan.

[huawei-GigabitEthernet0/0/1] port hybrid untagged vlan {vlan-id1 vlan-id2 ... vlan-idn}

Добавляем pvid для нетегированной vlan, по умолчанию используется pvid = 1

[huawei-GigabitEthernet0/0/1] port hybrid pvid vlan {vlan-id}

Пример:

[huawei] interface GigabitEthernet 0/0/1
[huawei-GigabitEthernet0/0/1] port link-type hubrid
[huawei-GigabitEthernet0/0/1] port hybrid tagged vlan 150 200 to 210
[huawei-GigabitEthernet0/0/1] port hybrid untagged vlan 10 20
[huawei-GigabitEthernet0/0/1] port hybrid pvid vlan 10 
[huawei-GigabitEthernet0/0/1] quit

P.S. По умолчанию на коммутаторах huawei S2300 и S5300 тип работы интерфейса стоит hybrid.

Просмотр настроек портов и vlan на коммутаторах huawei

Просмотр всех созданных vlan

[huawei] display vlan

Просмотр детальной информации по конкретной vlan на коммутаторах huawei

[huawei] display vlan vlan-id

Пример:

[huawei] display vlan 100

Просмотр состояния интерфейса на коммутаторах huawei

[huawei] display interface {type-interface-number}

Пример:

display interface GigabitEthernet0/0/1

huawei-S2300-S5300

Просмотр настроек интерфейса на коммутаторах huawei

[huawei] display current-configuration interface {type-interface-number}

Пример:

[huawei] display current-configuration interface GigabitEthernet 0/0/1/
#
interface GigabitEthernet0/0/1
port link-type access
port default vlan 150
#
return

Также настройки интерфейса можно посмотреть используя команду display this из режима конфигурирования интерфейса.

Пример:

[huawei] interface GigabitEthernet 0/0/1
[huawei-GigabitEthernet0/0/1] display this
#
interface GigabitEthernet0/0/1
port link-type access
port default vlan 150
#
return

На этом все. Всем пока.

Источник

Понравилась статья? Поделить с друзьями:
  • Port is error disabled cisco 2960
  • Position error exceeds the limit
  • Port in error or sync connect in error
  • Pos error handling облако
  • Port error mikrotik vpn