Содержание
- HP Proliant ML350 G5 Randomly Randomly Restarting
- Развалился 5-ТБ массив на HP Smart Array P410i
- Развалился 5-ТБ массив на HP Smart Array P410i
- Re: Развалился 5-ТБ массив на HP Smart Array P410i
- Re: Развалился 5-ТБ массив на HP Smart Array P410i
- Re: Развалился 5-ТБ массив на HP Smart Array P410i
- Re: Развалился 5-ТБ массив на HP Smart Array P410i
- Post error 1794 slot x drive array
- HP ProLiant G5 DL360 не запускается (жалуется на процессоры)
HP Proliant ML350 G5 Randomly Randomly Restarting
Today we found one of our HP Proliant ML350G5 down. Physical inspection revealed the following:
- Power Led: Green
Internal Health LED: Red
External Health LED: Red
Trying the change something using the power button doesn’t do anything. So we removed the power cord and booted the server normally.
It is worth noting that just a week ago this server started doing random restarts once or more per day without recording anything in the Events Logs exception the Kernel Power error.
Further check led us to find the following RAID Controller error «Code 263: Smart Array E200i in Embedded Slot has one or more array accelerator batteries/capacitors that are failed.» — we are in the process of replacing it because we updated to latest firmware without success.
What we will do next is:
- Update the BIOS — Done every since posting this thread
- Run the HP Insight Diagnostics
- Check the internal LEDs
But in the meantime, any thoughts what could be causing this? could it be a power supply issue, is it the RAID Controller battery, or maybe something else?
N.B. The server is in an air conditioned room and its heat sinks were cleaned earlier this year; so no overheating issues.
N.B2 (update): While updating the iLO2 firmware, the server crashed (restarted), but when we attempt to reinstall, it says it has been installed.
Источник
Развалился 5-ТБ массив на HP Smart Array P410i
Развалился 5-ТБ массив на HP Smart Array P410i
Сообщение igornov » 22 авг 2015, 03:53
Ранее один из дисков вылетел, но на Spare контроллер почему-то его не поменял. мои админы проворонили это и. теперь массив вообще не поднимается. Посоветуйте что можно сделать. на массиве есть ряд важных данных.
Массив Raid 5 из 13 дисков SATA (по 500 Гб)
Re: Развалился 5-ТБ массив на HP Smart Array P410i
Сообщение maverlife » 24 авг 2015, 06:24
Re: Развалился 5-ТБ массив на HP Smart Array P410i
Сообщение Stranger03 » 24 авг 2015, 13:24
Re: Развалился 5-ТБ массив на HP Smart Array P410i
Сообщение igornov » 25 авг 2015, 09:41
факта вылета 2-х дисков из массива не вижу. Один сгорел 3 месяца назад, на его место как оказалось всё-таки встал hotspare. Сейчас же этот hotspare стоит так как будто он и никогда не вставал вместо сбойного диска. Ну а все остальные диски в статусе OK. Хотя сам массив в статусе failed.
Вы пишете по одному вернуть в онлайн… но они все в статусе ОК + в утилитах к этому массиву нету никаких инструментов чтобы это сделать. можно только расширить массив, создать Spare или удалить массив.
Re: Развалился 5-ТБ массив на HP Smart Array P410i
Сообщение igornov » 25 авг 2015, 10:12
вот сообщает контроллер:
298 SATA Array B with Spare — 1 Logical Drive(s) contains a failed physical drive. To correct this problem, check the data and power connections to the physical drives or replace the failed drive. For more information, generate a diagnostics report under the Diagnostics tab.
274 0 MB SATA Drive at Port 4C : Box 2 : Bay 1 is bad or missing.
To correct this problem, check the data and power connections to the physical drive.
For more information, generate a diagnostics report under the Diagnostics tab.
271 (Failed) Logical Drive 2 (5.5 TB, RAID 5) has failed and cannot be used. All data on this logical drive has been lost. Configuration changes to this logical drive are not allowed until this problem is corrected. Also, if your controller supports Expansion, Extension, or Migration, these operations will not be available for any logical drives in the array until the problem is corrected.
Replace any failed physical drives and re-enable the failed logical drive. For more information, generate a diagnostics report under the Diagnostics tab.
Источник
Post error 1794 slot x drive array
Сообщения: 541
Благодарности: 71
| Конфигурация компьютера | |
| Материнская плата: Foxconn P35A-S (3 PCI, 1 PCI-E x1, 2 PCI-E x16, 4 DDR2 DIMM, Audio, Gigabit LAN, IEEE-1394) | |
| Видеокарта: NVIDIA GeForce GTX 650Ti | |
| Блок питания: FSP 550M 80 Plus Gold | |
| Монитор: Dell 27″ | |
| Индекс производительности Windows: 5,4 |
Профиль | Отправить PM | Цитировать
Существует сервер DL360 G4. На ней распаян RAID контроллер (SCSI) 6i. И сей контроллер глюканул (не проходит селф-тест).
При прохождении POST ошибка:
1783 — Slot 0 Drive Array Controller Failure — 6i
Рекомендации на сайте HP:
POST Error: 1783-Slot X Drive Array Controller Failure
Possible Cause: Controller failed. If this message is displayed after Options ROMPaq is run, issues may have occurred while attempting to flash the ROM.
Actions:
Reseat the array accelerator module.
Reseat the controller in the PCI slot.
If the issue persists, replace the array controller.
На форумах советуют практически тоже самое. А именно: рекомендуется заменить контроллер, прошить его или переинициализировать.
Поскольку контроллер не съемный (в принципе теоретически существует и съемный вариант), то первый вариант превращается в замену МВ (что довольно накладно и хотелось бы отложить на крайний случай).
Прошивку скормить контроллеру не удалось — видно плотно завис.
Вопрос: а как можно переинициализировать (обресетить) данный контроллер? Может кто сталкивался?
Может существуют совсем заковыристые но более дешевые пути? Перемычки? Ножки на микросхеме отпаять? Программатор? Станцевать с бубном? ))
——-
Самые простые методы — всегда самые действенные.
Источник
HP ProLiant G5 DL360 не запускается (жалуется на процессоры)
Все новые темы
| Автор | |||
|---|---|---|---|
| Staric1982 Участник форума Зарегистрирован: 23.09.2010
|
|
||
| Вернуться к началу |
|
||
 |
|||
| Зарегистрируйтесь и реклама исчезнет!
|
|||
|
|||
| Mydel123 Почетный житель Зарегистрирован: 22.10.2009 |
|
||
| Вернуться к началу |
|
||
|
|||
| Kolivan Новичок Зарегистрирован: 28.02.2012 |
|
||
| Вернуться к началу |
|
||
|
|||
| Staric1982 Участник форума Зарегистрирован: 23.09.2010
|
|
||
| Вернуться к началу |
|
||
|
|||
| Mydel123 Почетный житель Зарегистрирован: 22.10.2009 |
|
||
| Вернуться к началу |
|
||
|
|||
| Kolivan Новичок Зарегистрирован: 28.02.2012 |
|
||
| Вернуться к началу |
|
||
|
|||
| Staric1982 Участник форума Зарегистрирован: 23.09.2010
|
|
||
| Вернуться к началу |
|
||
|
|||
| Kolivan Новичок Зарегистрирован: 28.02.2012 |
|
||
| Вернуться к началу |
|
||
|
|||
| Staric1982 Участник форума Зарегистрирован: 23.09.2010
|
|
||
| Вернуться к началу |
|
||
|
|||
| Staric1982 Участник форума Зарегистрирован: 23.09.2010 Источник Adblock |
HP Proliant ML350 G5 Randomly Randomly Restarting
Today we found one of our HP Proliant ML350G5 down. Physical inspection revealed the following:
- Power Led: Green
Internal Health LED: Red
External Health LED: Red
Trying the change something using the power button doesn’t do anything. So we removed the power cord and booted the server normally.
It is worth noting that just a week ago this server started doing random restarts once or more per day without recording anything in the Events Logs exception the Kernel Power error.
Further check led us to find the following RAID Controller error «Code 263: Smart Array E200i in Embedded Slot has one or more array accelerator batteries/capacitors that are failed.» — we are in the process of replacing it because we updated to latest firmware without success.
What we will do next is:
- Update the BIOS — Done every since posting this thread
- Run the HP Insight Diagnostics
- Check the internal LEDs
But in the meantime, any thoughts what could be causing this? could it be a power supply issue, is it the RAID Controller battery, or maybe something else?
N.B. The server is in an air conditioned room and its heat sinks were cleaned earlier this year; so no overheating issues.
N.B2 (update): While updating the iLO2 firmware, the server crashed (restarted), but when we attempt to reinstall, it says it has been installed.
Источник
DL380 G6 slow hdd performance
Recently purchased a used DL380 G6, and overall, I’m quite happy with it, with the exception of HDD speed. It came with a 146GB SAS drive, and I added for the datastore a Seagate 1TB BarraCuda 5400 RPM 128MB Cache SATA 6.0Gb/s 2.5″. What I’m finding is that whenever there’s a lot of write activity, the VMs slow down to a crawl. Doesn’t matter if I use Ubuntu of Win10. (both setup with 8 cores, 32G RAM).
Now, I looked in the ILO2 log file and came across the following:
» POST Error: 1794-Drive Array — Array Accelerator Battery Charge Low «
Could this be the cause? And if so, does that mean the battery simply needs to be replaced? or is it a rechargeable battery? My google-fu is showing me «battery modules» which seem to be a whole unit, but not the battery? I’m a tad confused..
Enter to win a Win $150 GC and Binho Board set, or Intel® Pins
Seagate 1TB BarraCuda 5400 RPM 128MB Cache SATA 6.0Gb/s 2.5″.
Be aware the G6 is a 3G SATA connection, so the disk will only be operating at half the full speed, in addition to the 5400rpm spin, low seek times and a single disk being hit with writes, this is never going to be ideal.
More spindles is your friend here, not less disks with larger capacity.
Even if this is a lab you’d have been better with 4 x something in RAID10, a single disk is never going to be good, unless it’s an SSD and this will still have it’s limits.
16 Replies
For the SAS drive to work, I think you have to have a RAID card present as I don’t believe the motherboard ports support SAS. You need to replace your battery on the RAID card Without the battery writeback on the RAID controller will typically be disabled and that will kill performance on a hypervisor. Also, the 5400rpm Seagate is a miserably slow drive for a server, even a home server. A Pair of 7.2k identical drives in RAID1 that have TLER capability for the RAID are sort of the absolute minimum. More typical is 4 drive in RAID10 running as OBR10 (One Big RAID).
There are a few things to point out here.
Is the Barracuda a consumer/laptop drive or an official HCL drive? I’m assuming the former, 5400 rpm is slow, and these drives if they are laptop drives are slow generally, a single disk is not going to be anywhere near enough for multiple VMs, even as a lab.
Irrespective of what VM OS you use, your limited to about 80 IOPS and possibly less if this is not an officially supported drive.
5400rpm means seek times and access is even worse than regular SATA disks.
» POST Error: 1794-Drive Array — Array Accelerator Battery Charge Low «
BBWC is usually only for writes, but this is just telling you it has low capacity so if the server died or power was lost, the battery couldn’t retain the cached data long — it will charge over time or you need to replace the cache battery — but with a single disk this is quite pointless, when you have a RAID set it becomes more active. It’ll still be used, but likely not a lot of benefit at this point
Seagate 1TB BarraCuda 5400 RPM 128MB Cache SATA 6.0Gb/s 2.5″.
Be aware the G6 is a 3G SATA connection, so the disk will only be operating at half the full speed, in addition to the 5400rpm spin, low seek times and a single disk being hit with writes, this is never going to be ideal.
More spindles is your friend here, not less disks with larger capacity.
Even if this is a lab you’d have been better with 4 x something in RAID10, a single disk is never going to be good, unless it’s an SSD and this will still have it’s limits.
Thanks for the info. To be honest, that drive was a «cheap» testing solution, and it indeed a consumer version on a home lab. I basically wanted to make sure the server was functional before investing any kind of money in it. Your explanation(s) make a lot of sense now that I read them, so I appreciate that. Next step will be finding some cheap drives to replace that 1TB. eBay to the rescue I guess! Anything specific I should be looking for? There’s 8 bays in that system. Ultimately, I’d like to end up with 4-6 TB of storage.
Not going to happen cheaply.
Even if you bought all HP certified 1TB drives you’d want OBR10 and NOT RAID5 — while it is your lab, could you risk loosing everything or do you have good backups?
eBay will be your friend, the G6 is some years old now, i own a G7 and have 16 bays, all populated
10 x 300GB SAS and 6 x 1TB SATA
Well this is not a production device.. if anything, it’s more of a toy than anything else. I wouldn’t put anything of value on it, unless I have good backups of it. So other than for «playing around», this will end up being a combination of media server, minecraft server (my kid’s request, and i’ve been nagged daily about it for the past 3 weeks) and some ubuntu VMs for FTP/HTTP services. Nothing critical. The guy I bought the server from mentioned he had stacks of 146G SAS drives for $10/each.. I might start with that and expand later if I come across a decent deal on drives.
If this is a media system i see the need for lots of storage — in that case look to pickup a 2-4 bay readynas or similar from eBay and use regular SATA disks, keep the server and more expensive disks for lab stuff (that’s kind of what i do) and have the NAS do the media side of things — it’s more kit but well worth it in my opinion, especially since my lab does not impact my media this way
Except i never opt for a cheap NAS and currently own an 8 bay with 8 x 3TB for backup of my lab device, other home machines, my media and video storage (i do a lot of video editing so this is archive space)
The guy I bought the server from mentioned he had stacks of 146G SAS drives for $10/each.. I might start with that and expand later if I come across a decent deal on drives.
Go that route — i recently sold 10 x 146GB SAS disks on eBay (I’m in the UK) and shipped them off to the Netherlands at a price of £110 (
A media server can get big pretty fast. I run a vm with Plex Media Server on Ubuntu with a 4TB library on a 8x4TB SAS raid10 along with a couple Win2012 server VM’s on a Dell T610 and it is pretty snappy for a home server. I also store offsite backup for work so all told about 50TB of WD RE and HGST enterprise series drives on it, a Synology NAS and a 6×2 raid5 in a Dell T410 used just for storage. The 8 way raid10 is substantially faster at writing.
Learned my lesson with Minecraft — keep it (the server) on an isolated vm as the mods and themes are notorious for being malware laden.
Thanks Mark. It’ll be a Vanilla MC anyway, but yes, definitely on its own VM.
The guy I bought the server from mentioned he had stacks of 146G SAS drives for $10/each.. I might start with that and expand later if I come across a decent deal on drives.
Go that route — i recently sold 10 x 146GB SAS disks on eBay (I’m in the UK) and shipped them off to the Netherlands at a price of £110 (
Picking up 6 of them on Saturday. That’ll be a start.
You don’t mention your hyper visor. It’s drivers and settings can have an impact on your VMs.
RealM- is there such a thing as a vanilla Minecraft Server? We set one up for a group of kids 9-13 to provide a safe place away from mean people and mod requests started about week 2.
You don’t mention your hyper visor. It’s drivers and settings can have an impact on your VMs.
Ah yes, sorry. esxi 6.5. I could provide screenshots of settings if that’s any help, but keeping in mind I’m very new to all this, I’m not sure which info would be pertinent.
RealM- is there such a thing as a vanilla Minecraft Server? We set one up for a group of kids 9-13 to provide a safe place away from mean people and mod requests started about week 2.
Mine has been going on for about 4 months now (on an old PC running Ubuntu) and so far, no request for mods. knock on wood! 🙂 It’s used by my son and other autistic kids that he knows. I hop on once in a while to monitor, and they’re all having a great time building all sorts of things (and occasionally going pvp on each other, building traps and stuff.. bunch of lil geniuses!!) Anyway. back on topic now.. 🙂 (Feel free to PM me if you want to continue the MC discussion tho.. )
This topic has been locked by an administrator and is no longer open for commenting.
To continue this discussion, please ask a new question.
Read these next.
Bitlocker on a server
I need to encrypt my servers. Bitlocker being the main option. While I know I can store Bitlocker keys in AD to automatically unlock domain computers, how does this work with the domain servers? My fear is one day, I’ll end up restarting both of my d.
Creating powershell script
I need help with creating PowerShell script. Im not really that good at it. We are trying to delete alot of data then move it. Before we do that we need to run a script which can do the following:• The purpose of the script is to log each user• Show what .
Snap! — Flying Boats, Metaverse Vision, Floppy Disks in 2023, Replicated Cheese
Your daily dose of tech news, in brief. Welcome to the Snap! Flashback: January 12, 1997: HAL 9000 Becomes Operational (Read more HERE.) Bonus Flashback: January 12, 2005: NASA launched «Deep Impact» (Read more HERE.) You need to hear .
Spark! Pro Series — 12 January 2023
Today in History: 1984 Pyramid mystery unearthed An international panel overseeing the restoration of the Great Pyramids in Egypt overcomes years of frustration when it abandons modern construction techniques in favor of the method employed by .
Managing confidential/PII data in a non profit environment
I am looking for some suggestions on how manage confidential and Personally Identifiable Information in our non profit environment. We run a number of grant programs that require applicants to upload tax documentation, IDs, and other financial information.
Источник
1794-Drive Array — Array Accelerator Battery Charge Low…
…Array Accelerator is temporarily disabled.
Array Accelerator will be re-enabled when battery reaches full charge.
Audible Beeps: None
Possible Cause: The battery charge is below 75 percent. Posted writes are disabled.
Action: Replace the array accelerator board if the batteries do not recharge within 36 powered-on
hours.
1795-Drive Array — Array Accelerator Configuration Error…
…Data does not correspond to this drive array. Array Accelerator is temporarily disabled.
Audible Beeps: None
Possible Cause: Power was interrupted while data was in the array accelerator memory, or the data
stored in the array accelerator does not correspond to this drive array.
Action: Match the array accelerator to the correct drive array, or run ACU
on page 49) to clear the data in the array accelerator.
1796-Drive Array — Array Accelerator Not Responding…
…Array Accelerator is temporarily disabled.
Audible Beeps: None
Possible Cause: Array accelerator is defective or is missing. Depending on the array controller model,
the cache may be disabled or the controller might not be usable until this problem is corrected.
Action:
Reseat the array accelerator daughter board if the connector is loose.
1.
If the problem persists, replace the board.
2.
1797-Drive Array — Array Accelerator Read Error Occurred…
…Data in Array Accelerator has been lost.
Array Accelerator is disabled.
Audible Beeps: None
Possible Cause: Hard parity error detected while reading data from posted-writes memory.
Action: Replace the array accelerator daughter board.
1798-Drive Array — Array Accelerator Self-Test Error Occurred…
…Array Accelerator is disabled.
Audible Beeps: None
Possible Cause: Array accelerator failed self-test. Depending on the array controller model, the cache
may be disabled or the controller might not be usable until this problem is corrected.
Action: Replace the array accelerator daughter board.
1799-Drive Array — Drive(s) Disabled Due to Array Accelerator Data Loss…
…Select «F1» to continue with logical drives disabled.
Select «F2» to accept data loss and to re-enable logical drives.
(«Array Configuration
Utility»
Error messages 113