Riso ошибка a01 211 - Исправление ошибок и поиск оптимальных решений проблем

Type	Point	Description
A01	201	Master-positioning sensor does not go ON even after the write pulse motor is activated during the master-positioning, master-cut, or master-loading operation.
A01	202	Master-positioning sensor does not go OFF even when the write pulse motor is reversed during the master-positioning or at start of master-making operation.
A01	206	Timeout error during master-making operation
A01	211	Master-positioning sensor is ON during standby.
A01	214	Master-positioning sensor is ON at the start of master making.
A01	215	Faulty gate-array control for the write pulse motor (motor does not stop within set time)
A02	509	Master-loading sensor was OFF when the master was checked at a specified drum angle during the master-loading operation.
A04	303	Master-disposal jam sensor was OFF at both 120 and 180 degrees drum angle.
A04	314	Master-disposal error (recovery error).
A05	304	Master-disposal jam sensor was ON at the completion of the master-disposal operation.
A05	312	The master-disposal jam sensor was ON at the start of master-making operation.
A05	315	The master-disposal jam sensor was ON when the master disposal box was set in the machine.
A06	403	Paper-feed-tray upper or lower safety switch is OFF.
A07	409	Paper-ejection sensor was OFF when the paper should have arrived, and the paper sensor was ON when the machine stopped (Paper misfeed).
A07	412	Paper sensor was OFF three times in succession when a paper misfeed was detected (paper misfeed).
A07	413	Paper sensor was ON when the paper should have left the paper sensor (long-length paper mode error).
A07	418	The paper sensor was ON at the start of machine operation when the START button was pressed.
A07	429	Paper feed error (recovery error).
A07	432	Paper sensor was ON when the machine went into paper feed retry movement after a paper misfeed.
A08	410	Paper-ejection sensor was OFF when paper should have arrived, and the paper sensor was OFF when the machine stopped (paper jam on the print drum).
A08	421	Paper sensor was ON when the paper should have left the paper sensor during feeding of long paper in long-length paper mode (paper longer than 555 mm).
A08	430	Paper jam on print drum (recovery error).
A09	411	Paper-ejection sensor was ON when the paper should have left the paper-ejection sensor.
A09	417	Paper-ejection sensor was ON at the start of machine operation when the START button was pressed.
A09	431	Paper-ejection error (recovery error).
A10	102	Original-registration-sensor remaining jam
A10	103	Original-IN-sensor remaining jam
A10	105	Original-registration-sensor non-arrival jam
A10	106	Original-IN-sensor non-arrival jam
A10	107	Original-OUT-sensor non-arrival jam
A10	109	An original feed error occurred, due to opening the AF.
A10	162	No original in AF during AF master making.
A16	525	Waiting for the master to be removed.
A17	209	Cutter home-position switch is OFF at the start of master-making or master-set operation.
A34	218	Request to resetting the master.
B01	730	Keycard counter: No card
B22	721	With the «Tape separation» function set ON, no power is supplied to the job separator when start key is pressed.
B22	727	After cluster-A signal turned ON, BUSY-signal stayed «L» more than 7 seconds (power to job separator was turned OFF while the tape is being ejected.
B23	722	With the «Tape separation» function set ON, no tape detected in the job separator when the start key is pressed.
B23	723	No tape remains in job separator upon completion of the tape-ejection operation.
B24	724	Tape jam detected when the start key is pressed with the «Tape separation» function set to ON.
B24	725	Job separator tape-jam detection signal is «H» within 1,200 milliseconds after the cluster-A signal turns ON (tape misfeed).
B24	726	Job separator tape-jam detection signal is «L» when the BUSY signal changes from «L» to «H» (or after 7 sec. at «L») after the cluster-A signal goes ON (tape misfeed).
B31	916	Network cable is not connected when the machine is powered ON.
B32	917	Communication error on the network.
B32	920	Error detected by Network Interface Card (NIC) — NAK (negative acknowledgement was received).
B33	931	DHCP server is not found with DHCP ON.
B34	919	Error detected on the locally connected printer.
C01	512	The ink sensor did not go ON even when inking was performed for the preset period.
C01	563	Ink remaining amount is zero.
C01	574	Inkless error was detected 5 times consecutively on one same ink bottle.
C02	200	The master end was detected twice in succession at 10-milliseconds intervals during master transport.
C02	240	Master remaining amount is zero
C02	253	Masterless error was detected twice consecutively on one same master-roll.
C03	308	Compression detection position was reached before the master-compression-motor encoder-sensor count reached the specified level, after the master compression motor turned ON in the compression direction.
C03	313	Master removal box full detected by the master removal count.
C04	402	Paper detection sensor is OFF (no paper on the feed tray).
D01	526	Print drum is not set in the machine (drum connection signal, drum safety switch, and drum-lock sensor is OFF.
D01	527	Print drum connection signal is OFF when the print drum was inserted in the machine.
D01	528	Print drum safety switch is OFF when the print drum was inserted in the machine.
D01	529	Print drum lock sensor is OFF when the print drum was inserted in the machine (time-out: 5 seconds).
D01	530	Print drum connection signal does not go OFF within 5 seconds after the print drum safety switch went OFF when the print drum was pulled out.
D02	532	Incorrect print drum is used.
D03	533	Ink cartridge set sensor is OFF.
D04	534	Incorrect ink cartridge is used.
D04	560	Ink TAG is not detected on ink bottle.
D04	561	Ink cartridge communication error (communication with the ink cartridge was interfered by noise).
D04	562	Wrong ink cartridge information.
D04	564	Detected a mismatch in ink cartridge information
D05	210	Master detection sensor is OFF (not detecting master).
D07	310	Disposal-box safety switch is OFF.
D08	224	Master making unit is not set (both the safety switch and lock sensor are OFF).
D08	226	Master making unit safety switch is still OFF when the master making unit is set in position.
D08	227	Master making unit lock sensor is still OFF when the master making unit is set in position (timeout: 5 seconds).
D08	228	Master making unit lock sensor is still ON even after the master making unit safety switch went OFF, when the master making unit was pulled out of the machine.
D09	212	Master-making-unit set sensor is OFF (sensor light path is free).
D11	535	Front cover set switch is OFF.
D13	9	The rear cover is opened (serviceman safety switch is OFF).
D17	236	Incorrect master roll.
D17	237	Master roll undetected.
D17	238	Master roll communication error.
D17	239	Wrong master roll detected.
D17	241	Detected a mismatch in master roll information.
D18	522	Print drum ready for release (solenoid is ON).
D19	223	Master making unit ready for release (solenoid is ON).
D22	540	Error in access to the Drum PCB (unable to read from or write on the Drum PCB).
D22	542	Abnormal data on Drum PCB.
E01	10	Battery voltage was less than 2.5 V when the power was switched ON (weak battery: time to replace battery).
E02	11	Master counter reached the value set for the maintenance call (value set by test mode). [The message appears when either the power is turned ON, the unit is reset, or when the machine operation ended.]
E02	12	Copy counter reached the value set for the maintenance call (value by set test mode). [The message appears when either the power is turned ON, the unit is reset, or when the machine operation ended.]
E02	22	Maintenance counter inside the print drum reached the value set for the maintenance call (value set by test mode). [The message appears when either the power is turned ON, the unit is reset, or when the machine operation ended.]
F01	15	There is no master on the print drum at the start of printing.
F02	18	Paper size does not match with the image size on the print drum at the start of printing.
F03	16	Multi-up was selected using custom size paper.
F05	19	In master making, the print quantity selected is less than the minimum print quantity.
F10	21	Paper size does not match with the size of image on the print drum when test print is selected and activated.
F21	32	Next original is not in placed on AF for multi-up operation.
F22	33	Next original is not placed on flatbed for multi-up operation.
F37	50	Original was set on the AF with book mode selected, when master making is activated.
F50	910	Auto-printer-selection is disabled due to error on linked printer.
F54	923	Auto-printer-selection is disabled due to no paper in the linked printer.
F55	924	Auto-printer-selection is disabled while receiving print data from PC.
F58	927	Cannot print from linked printer (Initializing NET-C).
H1	566	Requesting ink color information input (Ink-TAG related).
H2	567	Requesting print density information input (Ink-TAG related).
H3	568	Requesting test printing print density information input (Ink-TAG related).
H4	242	Requesting master-making density information input (Master-TAG related).
H5	243	Requesting Print density information input (Master-TAG related).
H6	244	Requesting test printing print density information input (Master-TAG related).
P01	520	Main encoder sensor does not go ON/OFF within 10 milliseconds after the main motor activates.
P01	521	B-positioning sensor status does not change even after 3,033 pulses after the main motor activates.
P01	524	Clamp unit is not at the home position while the print drum is in operation (except during master disposal).
P01	537	Print drum failed to stop at position B. (over-run)
P01	538	Print drum is not locked during operation. (Print-drum lock position sensor: OFF)
P02	400	Both the upper and lower limit sensors were ON at the same time.
P02	401	Overload current was detected in the elevator motor.
P02	404	The lower-limit sensor does not go OFF within 2 seconds after the elevator motor operates in the raising direction from the lower-limit position.
P02	405	The upper-limit sensor does not go ON within 12 seconds after the elevator motor operates in the raising direction.
P02	406	The upper-limit sensor does not go OFF within 2 seconds after the elevator motor operates in the lower direction from the upper-limit position.
P02	407	The lower-limit sensor does not go ON within 12 seconds after the elevator motor operates in the lowering direction.
P02	408	The upper-limit sensor is OFF continuously for over 2 seconds during operation of the elevator servo action to raise the feed tray.
P03	500	Clamp sensor A is OFF after the completion of the clamp unit initialization or home positioning movement.
P03	501	Clamp sensor B does not change within 1 second from the time the clamp motor operates in the correct direction.
P03	502	Clamp sensor B does not change within 1 second from the time the clamp motor operates in the reverse direction.
P03	503	Clamp sensor A does not go ON within 3 seconds when the clamp unit makes initialization movement.
P03	504	At the start of Clamp plate open/close action, the the detection sequence of clamp-sensors A & B is abnormal.
P03	505	At the start of print drum Positon-A compensation movement, the detection sequence of clamp-sensors A & B is abnormal.
P03	506	At the start of Clamp unit Home-positioning movement, the detection sequence of clamp-sensors A & B is abnormal.
P03	507	Clamp sensor A is ON after the clamp release action is completed.
P03	508	Clamp sensor A is ON after the A-position compensating movement is completed.
P03	545	Clamp unit is not in the home position while the print drum is in movement (cause due to the clamp motor).
P04	513	The overflow sensor was ON for a set number of times in succession during the 10-millisecond-interval overflow-sensor check.
P05	603	The vertical-centering sensor does not switch ON even when the vertical-positioning pulse motor activated in the image-down direction for 5 seconds during vertical home positioning movement.
P05	604	The vertical-centering sensor does not switch OFF even when the vertical-positioning pulse motor activated in the image-up direction for 5 seconds during vertical home positioning movement.
P05	605	Even though the vertical positioning motor stopped according to the vertical centering sensor detection, the stopping position does not correspond with the programmed position. (GA control error).
P05	612	The one-step-positioning key was pressed with vertical-print-position information undefined.
P08	951	Print job executed was not in correct RisoRinc format.
P11	600	Print pressure HP sensor does not switch ON within 3.9 seconds after the print pressure pulse motor activated towards higher pressure during home positioning operation.
P11	601	Print pressure HP sensor does not switch OFF within 4.6 seconds after the print pressure pulse motor activated towards lower pressure during home positioning operation.
P11	602	Even though the print pressure control pulse motor stopped according to the print pressure HP sensor detection, the stopping position does not correspond with the programmed position. (GA control error).
P12	301	Master compression motor lock when moving compression plate up.
P12	305	Master compression sensor does not go ON within 6.5 seconds after the master compression motor operates in the return direction.
P12	306	Master compression sensor does not go OFF within 2 seconds after the master compression motor operates in the compress direction.
P12	307	Master compression plate maximum position is not detected within 6.5 seconds after the master compression motor operates in the compress direction.
P12	309	Master-compression-motor encoder sensor count did not change as the master compression motor activated in the compress direction and moved out from the home position.
P12	316	Master-compression-motor encoder sensor count did not change within 10 milliseconds after the master compression motor activated.
P12	300	Overload current was detected in the master removal motor.
P13	203	Cutter HP switch does not go OFF within 100 milliseconds after the cutter motor is activated.
P13	204	Cutter HP switch does not go ON within 300 milliseconds after the cutter motor is activated.
P13	205	Master-positioning sensor is ON when the print drum rotates through the preset angle following master cutting.
P13	221	Both the cutter HP switch and cutter stop position switch are ON at the same time.
P13	222	Cutter HP switch does not go ON within 450 milliseconds after the cutter home positioning operation started.
P13	231	Cutter HP switch does not go OFF within 500 milliseconds after the cutter moved out from the home position.
P13	232	Cutter stop position switch does not go ON within 2 seconds after the cutting operation started.
P13	233	Cutter stop position switch does not go OFF within 500 milliseconds after the cutter activates to move from the stop position to the home position.
P13	234	Cutter HP switch does not go ON within 2 seconds after the cutter home positioning operation started.
P14	114	Incorrect main-unit data.
P14	115	The scanner operation is not completed within the set time.
P14	116	Timeout error for black shading compensation. (RZ3 series only)
P14	117	Timeout error for white shading compensation. (RZ3 series only)
P14	123	Offset adjustment not completed within set time. (RZ3 series only)
P14	124	Gain adjustment not completed within set time. (RZ3 series only)
P14	125	Offset adjustment not completed.
P14	126	Gain adjustment not completed.
P14	135	Malfunction detected during offset adjustment. (RZ3 series only)
P14	136	Malfunction detected during offset adjustment. (RZ3 series only)
P14	137	Malfunction detected during black shading compensation. (RZ3 series only)
P14	138	Malfunction detected during white shading compensation. (RZ3 series only)
P14	170	Even though the read pulse motor stopped according to the sensor detection, the stopping position does not correspond with the programmed position. (GA control error).
P15	4	Communication error with AF-CPU.
P15	110	ABC (auto-base-control) timeout. The original does not move from the ABC scanning position on the AF unit.
P15	111	Operation command was made to the AF unit without 24 volts supplied to the AF unit.
P15	130	Timeout error in receiving reply from the AF unit after command signal was sent from the Riso printer to the AF unit.
P15	131	Riso printer received an undefined command from the AF unit.
P15	132	Riso printer detected communication sequence error from the AF unit.
P15	133	Communication error with AF unit (ACK or NAK error).
P15	134	Riso printer could not send command to the AF unit within the set time.
P15	160	AF unit detection signal went OFF while the AF unit is in operation.
P17	20	Solenoid counter is not connected.
P18	531	Print drum lock sensor is still ON even after 100 milliseconds after the print drum lock solenoid is activated.
P19	207	TPH pressure sensor does not go OFF within 2 seconds after the thermal-pressure motor activates in the decompressing direction, or during home positioning operation.
P19	208	TPH pressure sensor does not go ON within 2 seconds after the thermal-pressure motor activates in the decompressing direction.
P19	216	TPH pressure sensor does not go OFF within 500 millisecond after the thermal-pressure motor activates in the compressing direction.
P19	217	TPH pressure sensor does not go ON within 2 seconds after the thermal-pressure motor activates in the compressing direction.
P20	415	Paper-ejection-wing home sensor does not go OFF within 7,000 milliseconds after the paper ejection wing motor activates in the counterclockwise direction from the home position.
P20	416	Overload current was detected in the paper-ejection motor.
P20	437	Paper-ejection encoder sensor status does not change within 10 milliseconds after the paper-ejection motor is activated.
P24	539	Inking-motor encoder sensor status does not change within 20 milliseconds after the inking-motor is activated.
P25	26	Battery voltage was below 2.3 volts (too low) when the power is turned ON.
P92	570	EEPROM on the print drum PCB was being accessed while the print drum was in releasing action from the machine.
P93	932	No reply from the NET-C network interface card while accessing to the network interface card.
P93	933	No response from NET-C for 90 seconds during NET-C initialization.
P94	225	TPH code does not match with the machine code when the power is turned ON with the master-making unit in operating position or when the master-making unit is inserted in operating position while the power is ON.
P95	59	Machine serial-number information sent from SH-PCB does not match with the machine serial number information in the MCTL PCB.
P96	171	TPH resistance value not input.
P96	172	Scanner adjustment not completed.
P96	433	Paper size width potentiometer test-mode setting is not completed.
P96	569	Either the print drum color information or ink category information is still not input.
P96	613	Print pressure data missing.
P98	2	No reply from Mini-Rosa PCB when the machine power is turned ON even though the Rosa connection signal is ON.
P98	5	Hardware error.
P98	6	FRAM checksum error.
P98	7	Mini Rosa PCB not connected.
P98	38	Machine data on EEPROM does not match with that on the SH-PCB.
P98	39	Improper EEPROM on the SH-PCB.
P98	46	The DIMM capacity does not match.
P98	51	Touch-panel communication error
P98	53	Failure in calling out the saved Memory settings (program, mode, user paper information).
P98	54	Failure in saving the Memory settings (program, mode, user paper information).
P98	55	Machine type code from SH-PCB does not match with the machine information on the H8-PCB.
P98	63	The test-mode memory data stored was outside the adjustment range.
P98	64	An undefined command was sent in communication between SH-PCB and MCTL PCB.
P98	65	Communication error 01 between SH-PCB and MCTL PCB (MCTL PCB side).
P98	67	Communication error 03 between SH-PCB and MCTL PCB (MCTL PCB side).
P98	68	Communication error 04 between SH-PCB and MCTL PCB (MCTL PCB side).
P98	69	Communication error 05 between SH-PCB and MCTL PCB (MCTL PCB side).
P98	70	Communication error 06 between SH-PCB and MCTL PCB (MCTL PCB side).
P98	71	Communication error 07 between SH-PCB and MCTL PCB (MCTL PCB side).
P98	72	Communication error 08 between SH-PCB and MCTL PCB (MCTL PCB side).
P98	73	Communication error 09 between SH-PCB and MCTL PCB (MCTL PCB side).
P98	74	Communication error 10 between SH-PCB and MCTL PCB (SH-PCB side)
P98	75	Communication error 11 between SH-PCB and MCTL PCB (SH-PCB side)
P98	76	Communication error 12 between SH-PCB and MCTL PCB (SH-PCB side)
P98	77	Communication error 13 between SH-PCB and MCTL PCB (SH-PCB side)
P98	78	Communication error 14 between SH-PCB and MCTL PCB (SH-PCB side)
P98	79	Communication error 15 between SH-PCB and MCTL PCB (SH-PCB side)
P98	80	Communication error 16 between SH-PCB and MCTL PCB (SH-PCB side)
P98	81	Communication error 17 between SH-PCB and MCTL PCB (SH-PCB side)
P98	82	Communication error 18 between SH-PCB and MCTL PCB (SH-PCB side)
P98	83	Communication error 19 between SH-PCB and MCTL PCB (SH-PCB side)
P98	84	Communication error 20 between SH-PCB and MCTL PCB (SH-PCB side)
P98	98	Machine serial number information on the SH-PCB EEPROM does not match with that in the FRAM.
P98	119	Image processing PCB trouble.
P98	120	Scanner communication problem. (RZ3 series only)
P98	129	Faulty Scanner GA PCB. (RZ3 series only)
P98	245	Master transfer time-out error during master making (Write pulse motor error).
P98	246	Master transfer time-out error during master making (Load pulse motor error).
P98	614	Vertical print position data missing.
P98	934	Main read/write communication error (detected by read/write side).
P98	935	Main read/write communication error (detected by machine side).
P98	937	Serial number data missing.
P98	938	FRAM version-down.
P98	947	24V-A does not go ON (a possible burnt 24-volt group-A fuse).
P98	948	24V-B does not go ON (a possible burnt 24-volt group-B fuse).
P98	949	24V-A does not go OFF.
P98	950	24V-B does not fo OFF.
P98	952	Checksum error on the ROSA flash-memory.
P98	953	Unsuccessful writing on the ROSA flash-memory.
P99	936	Software error

Источник

10-23-2017

#1

Junior Member

Rep Power

0

RN2100 Error A01-211

Hey guys, we recently bought an old RN2100. It keeps showing us the message: «master mis-feed rewind master roll and reset master in place (A01-211)» of course we tried a lot of things (like cleaning and reassembly), but it still doesn’t work. Any ideas how to fix this or what could cause this?
10-24-2017

#2

Technician

Rep Power

23

Re: RN2100 Error A01-211

Hey there!
I think we had a similar issue on our RN2150.

I seem to remember it having to do with the 12 or so small rubber belts that pull the used master off the drum.
Very often these wear out, loose their elasticity and need to be replaced.

Try to open the top of the machine and then open the master disposal unit (there is a green lever that makes the unit pop open) and have a look at rubber belts. Are they inside their grooves? If not, pop them back in and try again. Are they broken? Too soft? The best is to get a new set and replace them all.
Also try to look at the belts from the back of the machine with the disposal box removed.

Hope that helps!
10-26-2017

#3

Junior Member

Rep Power

0

Re: RN2100 Error A01-211

Hey there we tried that and every thing seems fine with the rubber bands.

We opend the back to check the cables and everything seems in place. The first sensor on the master feed which tells if there is any input at all also works the error occurs with the second sensor under the metal rail. Also we can only get rid of the error with a hard reset not with pressing the resset button for 3 seconds.

Источник

Обзор ошибки замятие в ризографе

В прошлом обзоре мы познакомили вас с возможными типами ошибок, возникающих на ризографе и их идентификацией. Теперь мы рассмотрим индикаторы типов ошибок более подробно.

Первым в нашем списке будет индикатор замятия листов бумаги в том или ином месте ризографа. По-английски этот тип ошибки звучит как «JAM», т.е. замятие.

Для идентификации ошибки, связанной с замятием бумаги вам необходимо взглянуть на дисплей ошибок, на котором вы увидите номер в кружочке, который описывает место положения возникшей ошибки, а на дисплее тиражей собственно ее код. Далее вам нужно найти высветившийся номер ошибки в таблице с описанием, узнать причину, которая повлекла ошибку и выполнить указания по ее ликвидации.

Код ошибки А-01/34 (место положения 4, узел изготовления мастера)

Причина.
Данная проблема вызвана не верной установкой мастера в узел изготовления.

Устранение.
Для устранения данной ошибки достаточно разблокировать узел изготовления мастера, извлечь его и заново установить рулон мастер-пленки, при этом необходимо убедиться, чтобы мастер-пленка не провисала. Вернуть узел обратно.
Код ошибки А-02 (место положения 3, красящий цилиндр)

Причина.
Неправильно намотанный кадр мастер-пленки на красящий цилиндр.

Устранение.
Сначала вам нужно извлечь красящий цилиндр из ризографа. Далее вам необходимо разблокировать барабан при помощи рычага слева и повернуть барабан до тех пор, пока сверху не окажется металлический зажим мастера.

Далее, нажав на рычаг этого прижима, вам нужно поддеть за край и снять весь кадр мастер-пленки с цилиндра.

После того, как вы сняли мастер, вам необходимо провернуть барабан до совмещения меток и установить его обратно в ризограф. После этого разблокируйте узел изготовления мастера и извлеките его, произведите повторную установку мастера в узел и задвиньте узел изготовления обратно. Далее повторите процедуру по изготовлению нового мастера на ризографе.
Код ошибки А-04 (место положения 3, красящий цилиндр)

Причина.
Снятый кадр мастер-пленки не был загружен в контейнер для отработанных мастеров.

Устранение.
Сначала вам нужно извлечь красящий цилиндр и удалить с него кадр мастера. Далее верните барабан обратно в аппарат и нажмите кнопку «старт».
Код ошибки А-05 (место положения 5, контейнер отработанных мастеров)

Причина.
Подобная ошибка говорит о застревании бумаги в узле отработанных мастеров.

Устранение.
Сперва нужно извлечь контейнер отработанных мастеров с помощью нажатия специального рычага справа от контейнера.

Далее удалить застрявший мастер и произвести установку контейнера в обратном порядке.
Код ошибки А-06 (место положения 1, подающий стол)

Причина.
Под лотком или на бумаге имеются посторонние объекты.

Устранение.
Для исправления данной проблемы вам необходимо проверить подающий лоток, под ним и на бумаге на наличие посторонних предметов и при их наличии удалить.
Код ошибки J-08 (место положения 6, узел подачи бумаги)

Причина.
Обозначает, что в данном узле есть застревание бумаги.

Устранение.
Для исправления ошибки надо извлечь застрявшую бумагу и заправить лоток бумагой заново, далее для сброса ошибки нажать кнопку «сброс».
Код ошибки А-16 (место положения 3, красящий цилиндр)

Причина.
Проблема со снятием мастера с барабана.

Устранение.
Вам необходимо повторить все описанные действия по снятию кадра мастер-пленки с барабана, которые описаны выше к ошибке А-02 и повторить процедуру изготовления нового кадра мастера.
Код ошибки А-17 (место положения 4, узел изготовления мастера)

Причина.
Неправильно отрезан кадр мастер-пленки.

Устранение.
Нужно извлечь узел изготовления мастера и повторить заново установку рулона мастер-пленки.
Код ошибки J-01 (место положения 8, узел автоматической подачи бумаги)

Причина.
Если на вашем ризографе установлен АПО и горит данная ошибка, значит в АПО произошло застревание бумаги.

Устранение.
Для удаления проблемной бумаги из АПО необходимо потянуть рычаг разблокировки оригинала вправо и вытащить бумагу. Если же бумага застряла дальше данного узла, то надо поднять крышку ризографа вверх и провернуть ролик разблокировки АПО для удаления бумаги.
Код ошибки J-02 (место положения 6, узел приемного лотка)

Причина.
Обозначает, что в данном узле есть застревание бумаги.

Устранение.
Извлечь бумагу из зоны застревания и сбросить ошибку нажатием кнопки «сброс».
Код ошибки J-04 (место положения 3, красящий цилиндр)

Причина.
Проблема с застреванием листов бумаги в красящем цилиндре.

Устранение.
Извлеките цилиндр из ризографа, проверьте его на наличие замятой бумаги и при необходимости удалите ее.

Таким образом мы познакомили вас с ошибками ризографа, которые прямым образом связаны с застреванием мастера или бумаги в разный агрегатных узла аппарата. В следующем обзоре мы рассмотрим ошибки, связанные с индикатором активной функции.

Источник

	Серия RC
Call Service
Код Описание
Т1 Блокировка основного мотора
T2 Блокировка двигателя подъемного стола
T3 Ошибка зажимной пластины
T4 Перелив краски
T5 Блокировка мотора позиционирования оттиска
T6 Плохой контакт между печатными платами
T7 Плохой контакт с планшетом редактирования
T8 Плохой контакт с интерфейсом
T9 Плохой контакт с сортировщиком
T10 Нарушение работы датчика магнита А в барабан
T11 Блокировка мотора прижима
T12 Блокировка мотора отрезания мастера

          Серии RA, GR, FR
                     Call Service
                  Код Описание
Т1 Блокировка основного мотора
T2 Блокировка двигателя подъемного стола
T3     Ошибка зажимной пластины 1
T4    Перелив краски
T5    Блокировка мотора позиционирования оттиска
T6    Неисправности датчика наличия прижима
T7    Плохой контакт с планшетом редактирования
T8    Плохой контакт с интерфейсом
T9    Плохой контакт с сортировщиком
T10 Неисправность Trimming PCB
T11 Блокировка мотора прижима
T12 Плохой контакт между платами
T13 Блокировка мотора отрезания мастера
T14 Ошибка зажимной пластины 2
T15 Блокировка шагового мотора планшетного сканера
T16 Неисправность датчика положения С
T17 Заменить батарею
T18 Ошибка сортировщика
T19 Блокировка мотора прожига термоголовки
T20 Блокировка мотора крыльев выхода

        Серии TR, CR
              Call Service
           Код Описание

E1 Блокировка основного мотора

E2 Блокировка мотора подъемного лотка

E3 Блокировка мотора зажима

E4 Перелив краски

E5 Блокировка мотора позиционирования оттиска

E6 Неисправности датчика положения А

E7 Блокировка мотора прессования мастера

E8 Плохой контакт с периферией

E10 Ошибка теневой компенсации

E13 Блокировка мотора отрезания мастера

E14 Блокировка мотора снятия мастера

E15 Блокировка мотора пластины натяжения мастера

E16 Блокировка мотора помпы

E20 Блокировка мотора выдачи бумаги

E50 Подключить счетчик копий/мастеров

E77 Нет сигнала от термоголовки

E78 Ошибка выбора модели ризографа

Серии RN, RP

Call Service
Код Описание

Т1 Блокировка главного мотора

T2 Блокировка мотора перемещения лотка

T3 Мотор зажима

T4 Перелив краски

T5 Блокировка мотора вертикального позиционирования оттиска

T6 Блокировка мотора горизонтального позиционирования оттиска

T7 Плохой контакт с планшетом редактирования

T8 Плохой контакт с интерфейсом

T9 Ошибка дополнительного оборудования (выход бумаги)

T10 Ошибка дополнительного оборудования (подача бумаги)

T11 Блокировка мотора прижима

T12 Блокировка мотора съема мастера

T13 Блокировка мотора отрезания мастера

T14 Ошибка планшетного сканера

T15 Ошибка АПО

T17 Не подключен соленоид счетчика

T19 Блокировка мотора прижима термоголовки

T20 Блокировка мотора крыльев выхода

T22 Ошибка барабана

T23 Сканер не блокирован

T24 Блокировка мотора краски

T25 Нет сигнала батареи

T95 Ошибка платы MCTL PCB

T96 Ошибка записи данных барабана

T98 Системная ошибка плат, контактов, переключателей, контрольных сумм

Источник

RN2100 Error A01-211

Re: RN2100 Error A01-211

Re: RN2100 Error A01-211

Обзор ошибки замятие в ризографе

Код ошибки А-01/34 (место положения 4, узел изготовления мастера)

Код ошибки А-02 (место положения 3, красящий цилиндр)

Код ошибки А-04 (место положения 3, красящий цилиндр)

Код ошибки А-05 (место положения 5, контейнер отработанных мастеров)

Код ошибки А-06 (место положения 1, подающий стол)

Код ошибки J-08 (место положения 6, узел подачи бумаги)

Код ошибки А-16 (место положения 3, красящий цилиндр)

Код ошибки А-17 (место положения 4, узел изготовления мастера)

Код ошибки J-01 (место положения 8, узел автоматической подачи бумаги)

Код ошибки J-02 (место положения 6, узел приемного лотка)

Код ошибки J-04 (место положения 3, красящий цилиндр)