Sc544 02 ошибка ricoh

Dislikes:  0

1. 11-01-2014

   
   

   #1

   

   
   Senior Tech
   

   100+ Posts

   

   

   

   ---

   Rep Power

   0

   sc 544-002 mpc4503
   

   hi all

   i have problem with ricoh mpc4503 >>its give me (sc 544-002)

   i do this procedure:
   1- i replaced anew fusing unit them i execute sp5-810-002 … but the sc not gone >>

   please any one give me any advice about this sc

   best regards

   ---

2. 11-01-2014

   
   

   #2

   Re: sc 544-002 mpc4503
   

   Thermopile heat detection error.

   Take the fuser out and they are two sensors on a bracket above the fuser connector.
   Check they are clean and aligned with the fuser.

   Could be a problem with the new fuser if it’s not heating up at all after the SC has been cleared. (check the sleeve lamps, thermostats with a multi-meter).

   
   

   ---

3. 11-01-2014

   
   

   #3

   

   
   Senior Tech
   

   100+ Posts

   

   

   

   ---

   Rep Power

   0

   Re: sc 544-002 mpc4503
   

   thank you sir for your respond

   i checked and cleaned thermopile >>>>can you please tell me the best and easy way to measure the thermostat

   beast regards

   ---

4. 11-01-2014

   
   

   #4

   

   
   Senior Tech
   

   100+ Posts

   

   

   ---

   Rep Power

   25

   Re: sc 544-002 mpc4503
   

   You can not reset this spanner code without installing the new fuse that comes with the new belt assembly.

   Rebuild your fuser and replace the fuse at the same time, install it and the spanner code will still appear. Reset the fusing code now using SP5-810-002 and it will say completed, reboot device and it will come back to life

   ---

5. 11-01-2014

   
   

   #5

   

   
   Senior Tech
   

   100+ Posts

   

   

   

   ---

   Rep Power

   0

   Re: sc 544-002 mpc4503
   

   thank you Imprestiki did all this producer and all steps hat you said

   i replaced the new fusing with new belt assemble and so 5810-002 but the device don’t response and don’t give complete but still waiting

   ---

6. 11-01-2014

   
   

   #6

   

   
   Senior Tech
   

   100+ Posts

   

   

   

   

   ---

   Rep Power

   33

   Re: sc 544-002 mpc4503
   

   «SC544-02 and 554-02 cannot be cleared by replacing fusing unit and clearing SP5810»

   Update Engine Firmware > D1495503V

   ---

7. 11-01-2014

   
   

   #7

   

   
   Service Manager
   

   100+ Posts

   

   

   

   ---

   Rep Power

   32

   Re: sc 544-002 mpc4503
   

   QUOTE=Gamut;443756]»SC544-02 and 554-02 cannot be cleared by replacing fusing unit and clearing SP5810″

   Update Engine Firmware > D1495503V[/QUOTE]

   Actually Ricoh recommend to replace the whole fuser for any SC 544 but you can just replace the damaged parts and reset with a fuse and SP 5810-02

   SC544-02AFusing central NC sensor high temperature detection (hardware)In the event of an errorTriac defective (short-circuit)Engine controller defectiveHeating central thermopile defectiveFusing control software: out of control.

   Attach the new fusing unit, then run SP-5-810-002 If the triac is defective, replace the AC power supply board If necessary, replace the BCU or the Fusing central NC sensor

   ---

8. 11-01-2014

   
   

   #8

   

   
   Senior Tech
   

   100+ Posts

   

   

   

   

   ---

   Rep Power

   33

   Re: sc 544-002 mpc4503
   

   Originally Posted by Moza
   

   QUOTE=Gamut;443756]»SC544-02 and 554-02 cannot be cleared by replacing fusing unit and clearing SP5810″

   Update Engine Firmware > D1495503V

   Actually Ricoh recommend to replace the whole fuser for any SC 544 but you can just replace the damaged parts and reset with a fuse and SP 5810-02

   SC544-02AFusing central NC sensor high temperature detection (hardware)In the event of an errorTriac defective (short-circuit)Engine controller defectiveHeating central thermopile defectiveFusing control software: out of control.

   Attach the new fusing unit, then run SP-5-810-002 If the triac is defective, replace the AC power supply board If necessary, replace the BCU or the Fusing central NC sensor[/QUOTE]

   Probably not stated correctly in my reply, but actually if you have tried all that you state and still have SC544/554 code there is a FIRMWARE update (D1495503) that address’s this!

   ---

9. 11-01-2014

   
   

   #9

   Re: sc 544-002 mpc4503
   

   There should have been a fuse assembly taped to the inside of the box that a new fusing sleeve unit came in. That fuse has to be connected to the connector on the fusing in order for SP 5810 to work.

   ---

10. 11-03-2014

    
    

    #10

    Re: sc 544-002 mpc4503
    

    Had the same issue, fitted the fuse, updated firmware then I could reset the code in 5810-2

    ---