Send error 1103

Kyocera. 1102 ошибка

Перевод описания ошибки из сервисного руководства:

1102. Подсоединение к компьютеру не удалось:

1. Подтвердите имя пользователя и пароль.
2. Проверьте правильность параметров сети, к которой подключено устройство.
3. Проверьте компьютер, если папка правильно размещена.

1102 ошибка может возникать при:

1. Передаче через SMB‐сервер. Проверьте параметры настройки SMB:

1. имя пользователя и пароль при входе;

Примечание: Если отправитель является пользователем домена, укажите имя домена.

1. имя хоста;
2. путь.

1. Передаче электронного письма. Проверьте следующие настройки в COMMAND CENTER:

1. имя пользователя и пароль для сервера SMTP;
2. имя пользователя и пароль для сервера POP3.

1. Передаче через FTP‐сервер. Проверьте параметры настройки FTP‐сервера:

1. имя пользователя и пароль при входе;

Примечание: Если отправитель является пользователем домена, укажите имя домена.

1. путь;
2. право доступа получателя к папке.

Распространённые ошибки настройки: скорее всего, вы ввели короткий логин для доступа к папке вместо полного. Полный логин содержит имя домена (для доменной учётной записи), например: DOMAINUserLogin. (Для локального пользователя — просто UserLogin.) Если это условие выполнено, но ошибка появляется, проверьте настройки сетевого экрана (в качестве быстрой проверки (не рекомендуется) можно временно его полностью отключить). Также проверьте путь к папке сканирования (он должен быть максимально коротким (не более двух слешей).

Причины сбоев и ошибок:

1. Постоянная или временная недоступность настроенного сетевого ресурса.
2. Ограничение на допустимое количество символов в имени компьютера, имени пользователя и пароле — не более 64. Путь к сетевой папке не должен содержать более 128 символов.
3. Ошибка 1102 может возникать при использовании короткого логина вместо полного («имя домена имя пользователя (без кавычек и пробелов около косой черты).
4. Неверный путь к сетевой папке. Например, указан локальный путь, а не сетевой.
5. Если все сохраненные значения параметров верны, а при попытке сканирования возникает ошибка, проверьте настройки сетевого экрана (firewall’а — ‘брандмауэра’), возможно, что в сетевых правилах существует запись с более высоким приоритетом, блокирующая порт.

Чтобы избежать ситуаций с возникновением ошибок, необходимо изначально правильно настроить оборудование.

1. Проверьте сетевое полное имя компьютера (хоста), домен и имя пользователя и запишите значения. Пользователи Windows в командной строке могут набрать net config workstation либо получить нужные значения через «Свойства системы.
2. Создайте сетевую папку и настройте права доступа в ней. В общей папке можно создать подпапку в качестве расположения для передачи данных. В этом случае в поле «Путь нужно ввести «Имя общей папки Имя подпапки (без кавычек и пробелов около косой черты).
3. Включите общий доступ для файлов и принтеров и (если необходимо) настройте правило для входящих подключений: 139 порт по протоколу TCP. 139 — порт по умолчанию, но он может быть изменен (см. Руководство пользователя).

1. Убедитесь, что в COMMAND CENTER включены протоколы SMB и FTP (подробная информация изложена в руководстве пользователя, в том числе правило ввода символов).
2. Положите оригинал на стекло, нажмите клавишу «Отправить.
3. Выберите направление передачи: папка SMB или папка FTP.
4. Введите имя компьютера.
5. Введите имя папки, заданное в параметрах общего доступа.
6. Введите имя и пароль пользователя, которые используются для входа в компьютер с папкой общего доступа.
7. В случае удачной проверки нажмите «Подтвердить адресат и клавишу «Старт.

Примечание: При внесении неправильных данных могут возникать ошибки с кодами 1102, 1103 и 3101 при проблемах с FTP‐сервером.

Kyocera. Ошибка 1103

Может быть при сканировании может появиться при:

1. Передаче через SMB‐сервер. Проверьте параметры настройки SMB:

1. имя пользователя и пароль при входе;

Примечание: Если отправитель является пользователем домена, укажите имя домена.

1. путь;
2. право доступа получателя к папке.

1. Передаче через FTP‐сервер. Проверьте параметры настройки FTP‐сервера:

1. путь;
2. право доступа получателя к папке.

Ошибка 1105 Kyocera

1. Передаче через SMB‐сервер. Проверьте следующие настройки в COMMAND CENTER:

1. задайте значение «Вкл. для настроек SMB‐сервера.

1. Передаче электронного письма. Проверьте следующие настройки в COMMAND CENTER:

1. задайте значение «Вкл. для настроек SMTP‐сервера.

1. Передаче через FTP‐сервер. Проверьте следующие настройки в COMMAND CENTER:

1. задайте значение «Вкл. для настроек FTP‐сервера.

Технический центр. Обслуживание копировальных аппаратов, МФУ, принтеров. Поставка расходных материалов и оборудования. Заправка и восстановление картриджей. Техническая поддержка.

Предварительно следует настроить папку для получения документов на компьютере:

1. Проверьте сетевые «Полное имя» компьютера ( Хост ), домен и имя пользователя и запишите значения. Пользователи Windows в командной строке могут набрать » net config workstation «, либо получить нужные значения через Свойство компьютера.

2. Создайте сетевую папку и настройте права доступа в ней. В общей папке можно создать подпапку в качестве расположения для передачи данных. В этом случае в поле Путь нужно ввести » имя общей папкиимя подпапки «.

3. Включите общий доступ для файлов и принтеров и, если необходимо, настройте правило для входящих подключений: 139 порт по протоколу TCP . 139 — порт по умолчанию, может быть изменен (см. Руководство пользователя).

После этого можно переходить к настройке МФУ:

1. Убедитесь, что в COMMAND CENTER включены протоколы SMB и FTP (подробная информация изложена в руководстве пользователя, в том числе правило ввода символов).

2. Положите оригинал на стекло, нажмите клавишу Отправить .

3. Выберете направление передачи: Папка SMB или Папка FTP .

4. Введите Имя Хоста .

5. Введите имя папки, заданное в параметрах общего доступа.

6. Введите имя и пароль пользователя, которые используются для входа в компьютер с папкой общего доступа.

7. В случае удачной проверки нажмите Подтвердить адресат и клавишу Старт .

При внесении неправильных данных могут возникать ошибки с кодами 1102, 1103 и 3101 при проблемах с FTP сервером.

Причины сбоев и ошибок:

1. Постоянная или временная недоступность настроенного сетевого ресурса.

2. Ограничение на допустимое количество символов в имени Хоста, имени пользователя и пароле — не более 64. Путь к сетевой папке не должен содержать более 128 символов.

3. Ошибка 1102 может возникать при использовании короткого логина вместо полного » имя доменаимя пользователя «.

4. Неверный путь к сетевой папке, например указан локальный путь, а не сетевой.

5. Если все сохраненные значения параметров верны, а при попытке сканирования возникает ошибка, проверьте настройки Сетевого экрана (Брандмауэра), возможно в сетевых правилах существует запись с более высоким приоритетом, блокирующая порт.

Если ошибку устранить не удалось, то для решения проблемы рекомендуем обратиться в наш Технический центр .

вторник, 7 ноября 2017 г.

Ошибка 1102 Kyocera

В большинстве случаев, ошибка 1102 на принтерах Kyocera появляется при сканировании через сеть, из-за ее не корректной настройки.
Kyocera настройка сканирования по сети.
Заходим в web админку управления Kyocera по адресу http://ip_адрес_Вашего _устройства
Нажимаем «Вход в систему пароль на МФУ Куосера/Kyocera admin00

Открываем вкладку «Сканер» выбираем пункт «По умолчанию»и производим настройки сканирования по умолчанию
Далее открываем вкладку «Основные» выбираем «Адресная книга» и нажимаем «Добавить контакт».
У нас откроется окно в котором наc будет интересовать блок SMB
и вот в этом месте я потратил большую часть времени, но сейчас все распишу и поставим на этой проблеме точку.
— имя хоста — вводим имя компьютера или его ip адрес
— путь — тут вставляем название сетевой папки (если допустим у меня папка скан была расшарена на компе и доступ с компа был по адресу 192.168.60.6scan то значит в путь надо вписать только слово scan)
— имя пользователя — вписываем если локальный пользователь то простоuser, а если у вас доменная учетка, то domainuser
— пароль — пароль
Причины сбоев и ошибок:

1. Постоянная или временная недоступность настроенного сетевого ресурса.
2. Ограничение на допустимое количество символов в имени Хоста, имени пользователя и пароле — не более 64. Путь к сетевой папке не должен содержать более 128 символов.
3. Ошибка 1102 может возникать при использовании короткого логина вместо полного «имя доменаимя пользователя».
4. Неверный путь к сетевой папке, например указан локальный путь, а не сетевой.
5. Если все сохраненные значения параметров верны, а при попытке сканирования возникает ошибка, проверьте настройки Сетевого экрана (Брандмауэра), возможно в сетевых правилах существует запись с более высоким приоритетом, блокирующая порт.

Комментариев нет:

Отправить комментарий

Примечание. Отправлять комментарии могут только участники этого блога.

Устранение ошибок передачи и соединения на принтерах Kyocera

Ошибки передачи (1102, 1101, 2101) и соединения (0×1102) на принтерах Kyocera происходят из-за неправильной настройки, сетевых сбоев, неправильного ввода данных авторизации при подключении к папке на удаленном ПК.

Основной способ устранения сбоя – правильная настройка оборудования. Необходимо указать нужные параметры на печатающем устройстве и на компьютере, через который выполняется удаленное сканирование.

Что значит такая ошибка: информация из руководства

Неисправность возникает во время передачи документа в папку на удаленном ПК. Код 1102 или 1103 говорят, что принтер не получил доступ из-за неправильного ввода пары логин-пароль или адреса компьютера.

На устройствах Kyocera в случае такого сбоя отображается сообщение «Login to the host has failed». Также возможно появление надписи «Connection Error».

Когда возникает

На принтерах и МФУ ошибка вылетает в таких ситуациях:

• Работе через SMB или FTP сервер.
• Отправке электронных писем из-за ввода неактуальных username или пароля для сервера SMTP либо POP3.

Возможные причины сбоев

Причиной могут быть следующие факторы:

• Периодическое или постоянное отсутствие доступа к сети.
• Недопустимое число символов в названии устройства, логине, пароле.
• Указаны неполный домен, пользовательское имя.
• Путь к сетевой директории прописан неверно.

Неправильная настройка брандмауэра: наличие задач с более высоким приоритетом.

Правильная настройка

Для устранения неисправности нужно правильно настроить оборудование. Сначала проверьте параметры на компьютере, затем на печатающем устройстве.

Проверьте, правильно ли указано имя ПК, доменный адрес и username. Для этого введите в командной строке «net config workstation».

Убедитесь, что правильно указан путь к сетевой папке. Его можно посмотреть в свойствах.

Windows 7
Windows 10

Включите общий доступ для файлов и принтеров. Это можно сделать в «Центре управления сетями», во вкладке «Дополнительные параметры общего доступа».

Windows 7
Windows 10

Убедитесь, что на МФУ включены протоколы FTP и SMB. Это можно сделать через интерфейс Command Center. Отправьте оригинал документа, выбрав направление обмена данными.

Укажите имя компьютера и название папки, открытой для общего доступа. Пропишите актуальные данные авторизации для входа на ПК. После проверки подтвердите операцию, нажав «Старт».

Другие ошибки и их решение

На МФУ также могут появиться похожие сбои. Наиболее распространенные – 1103 и 1105.

Появляется при передаче через SMB либо FTP сервер из-за неправильно указанного имени пользователя либо пароля. Также появляется при отсутствии прав доступа к сетевой папке.

Возникает, если в Command Center на Kyocera не включена функция передачи через FTP, SMB или SMTP сервер. В этом случае необходимо задать значение в настройках принтера.

Источник

Ошибка 1102 Kyocera

Kyocera. 1102 ошибка

Перевод описания ошибки из сервисного руководства:

1102. Подсоединение к компьютеру не удалось:

1. Подтвердите имя пользователя и пароль.
2. Проверьте правильность параметров сети, к которой подключено устройство.
3. Проверьте компьютер, если папка правильно размещена.

1102 ошибка может возникать при:

1. Передаче через SMB‐сервер. Проверьте параметры настройки SMB:

1. имя пользователя и пароль при входе;

Примечание: Если отправитель является пользователем домена, укажите имя домена.

1. имя хоста;
2. путь.

1. Передаче электронного письма. Проверьте следующие настройки в COMMAND CENTER:

1. имя пользователя и пароль для сервера SMTP;
2. имя пользователя и пароль для сервера POP3.

1. Передаче через FTP‐сервер. Проверьте параметры настройки FTP‐сервера:

1. имя пользователя и пароль при входе;

Примечание: Если отправитель является пользователем домена, укажите имя домена.

1. путь;
2. право доступа получателя к папке.

Распространённые ошибки настройки: скорее всего, вы ввели короткий логин для доступа к папке вместо полного. Полный логин содержит имя домена (для доменной учётной записи), например: DOMAINUserLogin. (Для локального пользователя — просто UserLogin.) Если это условие выполнено, но ошибка появляется, проверьте настройки сетевого экрана (в качестве быстрой проверки (не рекомендуется) можно временно его полностью отключить). Также проверьте путь к папке сканирования (он должен быть максимально коротким (не более двух слешей).

Причины сбоев и ошибок:

1. Постоянная или временная недоступность настроенного сетевого ресурса.
2. Ограничение на допустимое количество символов в имени компьютера, имени пользователя и пароле — не более 64. Путь к сетевой папке не должен содержать более 128 символов.
3. Ошибка 1102 может возникать при использовании короткого логина вместо полного («имя домена имя пользователя (без кавычек и пробелов около косой черты).
4. Неверный путь к сетевой папке. Например, указан локальный путь, а не сетевой.
5. Если все сохраненные значения параметров верны, а при попытке сканирования возникает ошибка, проверьте настройки сетевого экрана (firewall’а — ‘брандмауэра’), возможно, что в сетевых правилах существует запись с более высоким приоритетом, блокирующая порт.

Чтобы избежать ситуаций с возникновением ошибок, необходимо изначально правильно настроить оборудование.

1. Проверьте сетевое полное имя компьютера (хоста), домен и имя пользователя и запишите значения. Пользователи Windows в командной строке могут набрать net config workstation либо получить нужные значения через «Свойства системы.
2. Создайте сетевую папку и настройте права доступа в ней. В общей папке можно создать подпапку в качестве расположения для передачи данных. В этом случае в поле «Путь нужно ввести «Имя общей папки Имя подпапки (без кавычек и пробелов около косой черты).
3. Включите общий доступ для файлов и принтеров и (если необходимо) настройте правило для входящих подключений: 139 порт по протоколу TCP. 139 — порт по умолчанию, но он может быть изменен (см. Руководство пользователя).

1. 1. Убедитесь, что в COMMAND CENTER включены протоколы SMB и FTP (подробная информация изложена в руководстве пользователя, в том числе правило ввода символов).
   2. Положите оригинал на стекло, нажмите клавишу «Отправить.
   3. Выберите направление передачи: папка SMB или папка FTP.
   4. Введите имя компьютера.
   5. Введите имя папки, заданное в параметрах общего доступа.
   6. Введите имя и пароль пользователя, которые используются для входа в компьютер с папкой общего доступа.
   7. В случае удачной проверки нажмите «Подтвердить адресат и клавишу «Старт.

Примечание: При внесении неправильных данных могут возникать ошибки с кодами 1102, 1103 и 3101 при проблемах с FTP‐сервером.

Kyocera. Ошибка 1103

Может быть при сканировании может появиться при:

1. Передаче через SMB‐сервер. Проверьте параметры настройки SMB:

1. имя пользователя и пароль при входе;

Примечание: Если отправитель является пользователем домена, укажите имя домена.

1. путь;
2. право доступа получателя к папке.

1. Передаче через FTP‐сервер. Проверьте параметры настройки FTP‐сервера:

1. путь;
2. право доступа получателя к папке.

Ошибка 1105 Kyocera

1. Передаче через SMB‐сервер. Проверьте следующие настройки в COMMAND CENTER:

1. задайте значение «Вкл. для настроек SMB‐сервера.

1. Передаче электронного письма. Проверьте следующие настройки в COMMAND CENTER:

1. задайте значение «Вкл. для настроек SMTP‐сервера.

1. Передаче через FTP‐сервер. Проверьте следующие настройки в COMMAND CENTER:

1. задайте значение «Вкл. для настроек FTP‐сервера.

Источник

Расшифровка кодов ошибок лазерных принтеров Kyocera FS-1020MFP/ 1025MFP/ 1030MFP/ 1120MFP/ 1125MFP/ 1220MFP и прочих моделей

Японская компания Kyocera производит высококачественные лазерные принтеры и МФУ для офисной печати. Их продукция одна из самых востребованных на сегодняшний день. Ведь печатающие устройства Kyocera характеризуются высокой надежностью, износостойкостью и большим сроком эксплуатации. Однако даже их изделия не являются вечными. Со временем принтеры Kyocera начинают сбоить.

К счастью, оргтехника Kyocera оснащена системой самодиагностики (так же, как и струйные принтеры Canon). Поэтому, в случае возникновения проблемы, устройство самостоятельно выявит уязвимое место и сообщит Вам об этом миганием соответствующего индикатора на панели управления либо кодом ошибки, выведенным на дисплей принтера.

Если Вы не являетесь мастером по обслуживанию принтеров и МФУ Kyocera, то, чтобы понять, о чем сообщает печатающее устройство, Вам потребуется расшифровать указанный им код. Для этого мы добавили в статью таблицу кодов ошибок лазерных принтеров Kyocera серии FS и не только.

Коды ошибок принтеров и МФУ Kyocera, которые можно исправить самостоятельно

Код ошибки

Значение ошибки

Решение проблемы

E-0001 (E1)

Поврежден чип картриджа либо установлен неоригинальный картридж.

Замените установленный картридж оригинальной версией изделия. Если хотите сэкономить, тогда купите и установите новый чип на картридж или перепрошейте принтер Kyocera. Однако предварительно не помешает попробовать сбросить ошибку соответствующей комбинацией клавиш (как это сделать, читайте в статье «Сброс ошибки установки неоригинального картриджа в принтерах Kyocera»).

E-0002 (E2)

Регион использования картриджа и принтера не совпадают.

Замените чип или прошейте принтер Kyocera.

E-0003 (E3)

Заполнена память принтера или МФУ Kyocera.

Отпечатайте ранее отсканированные листы или очистите очередь печати нажатием кнопки Стоп/Сброс (ранее отсканированные листы также удалятся из памяти принтера, даже если они еще не были распечатаны).

E-0007 (E7)

Тонер-картридж Kyocera израсходовал ресурс красящего вещества.

Замените или заправьте картридж Kyocera (если используете совместимый или перезаправленный расходник, то после установки его в принтер не забудьте сбросить ошибку зажатием на 3-5 секунды кнопок [Ок] и [Сброс/Стоп]).

E-0008 (E8)

Открыта крышка принтера либо не работает датчик закрытия крышек устройства.

Откройте и еще раз закройте переднюю и заднюю крышку принтера. Во время закрытия Вы должны услышать характерный щелчок. Если не помогло, то причина в неисправности датчика.

E-0009 (E9)

Лоток приема бумаги полон.

Уберите все отпечатанные листы бумаги из выходящего лотка. Чтобы возобновить печать, нажмите кнопку [Старт].

E-0012 (E12)

Ошибка памяти принтера Kyocera.

Попробуйте уменьшить разрешение печати. Скорее всего, формат создаваемого отпечатка не соответствует возможностям принтера.

E-0014 (E14)

Установлен неверный формат бумаги (неподдерживаемый принтером Kyocera).

Поменяйте бумагу на поддерживаемую принтером либо смените ее формат в настройках печати. Попробуйте обновить программное обеспечение. Возможно, это расширит поддерживаемые принтером Kyocera форматы.

E-0015 (E15)

Устройство не подключено к электрической сети либо на компьютере нет (не работает) драйвера принтера Kyocera.

Проверьте подключение печатающего аппарата к электрической сети, а также целостность кабеля. Если ошибка не исчезает, скачайте драйвер принтера Kyocera и установите его на компьютер.

E-0017 (E17)

Ошибка передачи данных.

Проверьте подключение принтера к компьютеру. Кабель не должен быть длиннее 5 метров, а также обязан поддерживать стандарт USB 2.0. Кроме того, переустановите драйвер принтера и утилиту Kyocera Client Tool.

E-0018 (E18)

Очередь печати заполнена.

Очистите очередь печати нажатием кнопки [Сброс] либо через драйвер принтера.

E-0019 (E19)

Неверный формат печати.

Отмените печать нажатием кнопки [Стоп/Сброс]. Выберите в настройках принтера соответствующий режим печати, а также установите в лоток поддерживаемый принтером формат бумаги.

J-0000 (jam0000)

Замятие бумаги за задней крышкой.

Откройте крышку и извлеките бумагу. Проверьте надежность крепления бумаги в лотке, а также принтер на наличие посторонних предметов. Еще причина может быть в пружине выходного флажка. Если она растянулась, то может плохо работать фиксатор. Также проблема может быть из-за печки, сделайте ее ревизию, переборку и смазку.

J-0501 (jam0501)

Бумага застряла в принтере Kyocera

Извлеките замятую бумагу. Проверьте надежность установки бумаги во входной лоток. Проверьте целостность роликов протяжки бумаги, а также принтер на наличие посторонних предметов. Если не помогло, стоит внимательно осмотреть ребра на направляющей пластине. На них могут образоваться сколы, трещины и заусенцы. Их можно слегка подчистить наждачной бумагой (нулевкой).

J-0511 (jam0511)

Принтер Kyocera замял бумагу.

Извлеките замятую бумагу и повторите печать. Если проблема не исчезла, несите принтер в сервис. Скорее всего, изношен ролик протяжки бумаги.

C7990

Бункер драм-картриджа (блока фотобарабана) заполнен отработанным тонером либо неисправен счетчик отработки красящего вещества. Еще проблема может быть в главной плате PWB.

Осуществите чистку драм-картриджа (блока фотобарабана). Если проблема в датчике или плате, то нужно отнести принтер в СЦ на диагностику.

F248

Ошибка обработки отпечатываемого материала.

Перезагрузите принтер. Уберите неподдерживаемые спецсимволы из отпечатка. Обновите ПО принтера Kyocera. Смените режим работы принтера с PDL на GDI (Пуск -> Принтеры -> Свойства -> Параметры устройства).

PF

Отсутствует бумага в лотке подачи.

Загрузите листы бумаги во входной лоток. Если принтер по-прежнему не печатает, значит нужно искать проблему в чем-то другом.

1101

Ошибка сканирования через сеть из-за неправильного имени SMTP сервера.

Пропишите DNS-адреса помимо прочих настроек печати по сети.

1102

Некорректная настройка сканера для работы через сеть

Зайдите в Web-панель управления принтером (нужно в адресную строку браузера ввести iP принтера Kyocera). Далее в зависимости от модели введите логин и пароль (Admin/Admin или просто admin00 без логина). Далее следуйте инструкции:

• Откройте вкладку «Сканер» и установите настройки по умолчанию;
• Перейдите на вкладку «Основные», выберите адресную книгу и нажмите добавить контакт;
• В открывшемся окне найдите блок SMB и введите: имя хоста = имя компьютера или его iP-адрес, путь = название сетевой папки (если не расшарена, то вместе с ИП-адресом), имя пользователя = user или domainuser (в зависимости от типа профиля), пароль = пароль.

Логин и пароль нужны обязательно, если их нет, то следует создать.

2101

Ошибка передачи данных при сканировании через сеть.

Правильно настройте параметры (как для ошибки 1102), только предварительно отключите на ПК антивирус и брандмауэр.

Если Вы испытали все способы, но не смогли убрать ошибку, то следует нести печатающее устройство в сервисный центр. Кроме того, есть ряд ошибок (высвечиваемых на дисплее принтера), которые нельзя устранить в домашних условиях. Соответствующие коды ошибок принтеров Kyocera представляем в очередной таблице.

Коды ошибок принтеров и МФУ Kyocera, которые нужно устранять в сервисном центре

Код ошибки

Значение ошибки

Решение проблемы

0030

Неисправность платы управления факсом принтера.

0100

Неисправность платы управления или флеш-памяти принтера.

0120

Ошибка чтения mac-адреса из-за неисправности флеш-памяти принтера.

0190

Неисправность платы управления или флеш-памяти принтера.

0630

Неисправность платы управления принтера.

1020

Неисправность мотора, привода или отсутствие контакта.

Разборка принтера и замена изношенных частей. Проверка надежности подключений, замена разорванных (прогоревших) кабелей. Ремонт или замена привода мотора.

1040

Неисправность мотора, привода или отсутствие контакта.

Разборка принтера и замена изношенных частей. Проверка надежности подключений, замена разорванных (прогоревших) кабелей. Ремонт или замена привода мотора.

2000

Неисправность главной платы управления, соединительного кабеля или привода принтера.

Проверить ремни, шестерни и ролики привода. Смазать или заменить, если есть дефекты. Заменить привод или главную плату.

3100 (C3100)

Неисправность главной платы, привода сканера, датчика положения или нарушение целостности соединений.

Проверить наличие разрывов и отсутствия контакта. Смазать или заменить изношенные элементы привода. Заменить привод, главную плату, датчик или соединительный кабель. Если Вам повезло, то возможно забыли отключить фиксатор блока сканера.

3101

Сетевой кабель не подсоединен, или нарушена работа концентратора. Еще может быть из-за наличия вирусов в системе или неправильно заданным параметрам сервера SMTP.

Проверить соединения, правильно настроить параметры сети.

3300

Неисправность главной платы, датчика CIS или соединительного кабеля.

Проверить контакты, заменить плату или датчик.

3500

Неисправность главной платы или нарушение соединения контактов.

Проверить контакты, заменить плату.

4000 (C4000)

Неисправность главной платы, привода сканера или нарушение соединений. Однако чаще всего ошибка лазера.

Проверить контакты, заменить плату или привод блока сканера. Почистить лазер, смазать ось полигон-мотора, либо полностью заменить блок лазера.

4200

Неисправность главной платы, блока сканера или датчика BD.

Отключить питание принтера на 30 минут. Если не помогло, то следует заменить привод сканера или главную плату принтера.

6000 (С6000)

Неисправность главной платы, термостата, печки или нарушение соединения контактов.

Проверить и поправить контакты. Заменить фьюзер. Ремонт или замена печки, термодатчика, термопредохранителя и т.д.

6020

Сгорание термистора или главной платы.

Замена термистора или главной платы.

6030

Неисправность главной платы, термостата или термистора. Возможно, причина в отсутствии контакта.

Проверить соединения. Заменить плату, термостат или термистор.

6400

Неисправность главной платы, отсутствие питания или контакта.

Заменить плату или источник питания.

F000

Неисправность главной платы или отсутствие контакта.

Проверить соединение ремня безопасности. Заменить ремень или плату управления.

F020

Неисправность элементов памяти принтера.

Перезагрузить принтер. Если ошибка не устранилась – заменить плату управления.

F040

Неисправность главной платы принтера.

Перезагрузить принтер. Если ошибка не устранилась – заменить плату управления.

F05D

Неисправность главной платы. Сбой программного оборудования привода. Проблемы с прошивкой принтера Kyocera.

Перезагрузить принтер. Если ошибка не устранилась – заменить плату управления. Перепрошить принтер Kyocera.

F245 F246 F247 F375

Принтер Kyocera заблокирован из-за проблемы, вызванной отказом источника питания.

Нужно перепрошить принтер специальной сервисной микропрограммой.

Обратите внимание: Если у печатающего устройства нет дисплея, то определить проблему можно по светодиодным индикаторам, встроенным в панель управления принтером. Например, у Kyocera Ecosys P2135D нужно сосчитать количество миганий индикаторов красного цвета и таким образом определить число, указывающее на ту или иную ошибку. В свою очередь, у модели Kyocera FS-1040 все зависит от темпа мигания светодиода с надписью «Внимание!» («Attention!»):

• Мигает медленно – указывает на отсутствие бумаги в лотке или тонера в картридже.
• Мигает быстро – оповещает о проблеме с памятью устройства, переполненном лотке или замятии бумаги, а также об использовании неоригинальных расходных материалов.
• Горит постоянно – говорит о проблемах с картриджем или фотобарабаном либо указывает на открытые крышки принтера.

Чтобы потребитель мог наверняка определить проблему, рекомендуем использовать утилиту Kyocera Client Tool, которая идет в комплекте с драйверами принтера.

Источник

Error Code Description C0030 Fax PWB Problem. Processing with fax software is disabled due to software or hardware issues. C0060 Main PWB Type Mismatch Error. C0070 Fax PWB Incompatability Detection Problem. Fax software is not compatible with main PWB software. C0130 Main PWB EEPROM Backup Memory Device Problem. EEPROM can not be written or read. C0140 Main PWB EEPROM Backup Memory Data Problem. Abnormal reading data from EEPROM. C0150 Engine PWB EEPROM Backup Memory Device Problem. EEPROM cannot be written or read. C0160 Engine PWB EEPROM Backup Memory Data Problem. Abnormal reading data from EEPROM. Read & write data do not match five times consecutively. C0170 Copy Counts Problem. A checksum error is detected in the main and engine backup memories for copy counters. C0180 Machine Number Mismatch Error. Machine number does not match on main and engine PWBs C0600 Main PWB DIMM Installed Incorrectly. C0610 Main PWB DIMM error C0630 DMA transmission of compressed, decompressed, rotated, relocated, or blanked-out image data does not complete within a specified period of time. C0640 Hard Disk Drive cannot be accessed C0700 Optional CF backup is not suitable. C0800 Image processing problem. JAM05 is detected twice. C0830 Fax Flash ROM program area checksum error C0870 Fax PWB to Main PWB high capacity data transfer problem. C0880 Fax PWB program archive problem. C0920 Fax backup data is not retained. C1010 Cassette #1 Lift Motor error. Exceeds 12 seconds of operation or 500ms of overcurrent. C1020 Cassette #2 Lift Motor error. Exceeds 12 seconds of operation or 500ms of overcurrent. C1030 PF-700 optional cassette #3 lift motor error. C1040 PF-700 optional cassette #4 lift motor error. C1100 PF-750 (Left) Lift Motor 1 error. Exceeds 1 second overcurrent. C1110 PF-750 (Right) Lift Motor 2 error. Exceeds 1 second overcurrent. C1120 PF-750 (Left) Lift Motor 1 position problem. PF switch 2 remains off after 30 seconds of motor operation. C1130 PF-750 (Right) Lift Motor 2 position problem. PF switch 1 remains off after 30 seconds of motor operation. C1800 PF-700/PF-750 Communication Problem. C1900 PF-700 EEPROM error. Write data & Read data are not in agreement three times consecutively. C2000 Drive Motor Problem. Stable Off is detected exceeding 1 sec after motor stability. Stabilization is not detected with 6 sec of activation. C2250 Main Charge Cleaner Motor error. Lock error is detected three times in a row during cleaner motor operation. C2500 Paper Feed Motor error. Stable Off is detected exceeding 1 sec after motor stability. Stabilization is not detected within 6 seconds of activation. C2600 PF-700 Drive Motor error. Lock signal exceeds 500ms. C2600 PF-750 Paper Conveying Motor error. Lock signal exceeds 450ms. C3100 Scanner Carriage Problem. Scanner home position is not detected at initialization or start of copying from contact glass. C3200 Exposure Lamp Problem. Exposure lamp does not reach the input value threshold within 5 sec of commencing reading. C3210 Exposure Lamp Problem. Exposure lamp does not exceed the input threshold value within 5 sec of commencing reading. C3300 CCD AGC Problem. After AGC correct input is not obtained at the CCD. C3310 CIS AGC Problem. After AGC correct input is not obtained at the CIS. C3500 Communication Error Between Scanner and SHD. C3900 Scanner PWB Backup Memory Read/Write Problem. Read & Write data does not match. C3910 Scanner PWB Backup Memory Data Problem. Data in a specified area of the backup memory does not match the specified values. C4000 Polygon Motor Synchronization Problem. Polygon motor does not stabilize speed within 20 sec of activation. C4010 Polygon Motor Steady-State Problem. Stable Off is detected for 20 sec continuously after polygon motor stabilization. C4200 BD Steady-State Problem. ASIC detects a Beam Detect error A for 2 sec after polygon motor stabilization. C5300 Cleaning Lamp Broken Wire. While the cleaning lamp is On, the broken wire detection signal is detected for 2 sec continuously. C6000 Fuser Heater Break. Thermistor1 detected less than 70C/158F for 10 sec during warmup & ready. Thermistor2 detected less than 40C/104F for 10 sec during warmup & ready. Temp at thermistor 1or 2 does not rise by at least 1C/1.8F within 5 sec. C6020 Abnormally High Thermistor Temperature. Thermistor 1 or 2 is detected 250C/482F for 40ms or more. C6030 Fixing Thermistor Break Error. Thermistor break signal is detected for 1 sec. C6050 Abnormally Low Thermistor Temperature. Thermistor 1 is detected 80C/176F or less for 1 sec continuously during copying. C6400 Zero-Cross Signal Error. While fuser heater On/Off control is performed, the zero-cross signal is not input within 3 sec. C6410 Fuser Unit Connection Insertion Problem. Absence of fuser unit is detected. C6420 Fuser Unit Fuse Cut Problem. The fuse has been cut 33 sec after the fuse cut signal is turned on. C7300 Toner Container Problem. Toner level is not detected when toner empty is detected. C7400 Developing Unit Connection Insertion Problem. Absence of the developing unit is detected. C7410 Drum Unit Connection Insertion Problem. Absence of the drum unit is detected. C7800 Broken External Thermistor Wire. Thermistor on the environmental sensor outputs 4.5v or more. C7810 Short-Circuited External Thermistor. Thermistor input value is 0.5v or less. C7900 Drum EEPROM Error. Reading or writing to the EEPROM cannot be performed. C7910 Developing EEPROM Error. Reading or writing to the EEPROM cannot be performed. C8020 DF-710 Punch Motor Problem. Punch motor lock signal is detected for 500ms or more during activation. C8030 DF-730 Tray Upper Limit Detection Problem. When tray elevation motor raises a tray, the upper limit switch detects On condition. C8050 DF-710 Paper Conveying Belt Motor 1 Error. Paper conveying belt home position sensor 1 does not turn Off within 1.5 sec. Paper conveying belt home position sensor 1 does not turn On within 2.5 sec. Jam 88. C8060 DF-710 Paper Conveying Belt Motor 2 Error. Paper conveying belt home position sensor 2 does not turn Off within 1.5 sec. Paper conveying belt home position sensor 2 does not turn On within 2.5 sec. C8070 DF-710 Internal Tray Communication Error. The connection is detected, but communication is not possible with the internal tray. C8140 DF-710 Main Tray Problem. Main tray is not detected in not detected by main tray top limit detection sensor or main tray capacity detection sensor within 20 sec of ascending. Main tray upper limit detection sensor or main tray load detection sensor is not detected as Off within 20 sec of main tray descending. Main tray lower limit detection sensor is not detected as On within 20 sec of main tray descending. Main tray upper limit detection sensor or main tray load detection sensor remain on for 2 sec or more during main tray ascent. C8140 DF-730 Tray Elevation Motor Problem. Tray lower limit sensor or surface view sensor cannot be detected within 10 sec. C8170 DF-710 Side Registration Motor 1 Problem. During initial rotations home position is not detected within 3 sec. Jam 88. C8170 DF-720 Front Side Registration Motor Problem. During initial rotations home position is not detected within 106 pulses. When the front side home position sensor is turned off during initialization, the sensor did not turn on within 3 sec. C8170 DF-730 Adjustment Motor Problem. Adjustment motor home position motor is not detected within a specific time during activation. C8180 DF-710 Side Registration Motor 2 Problem. During initial rotations home position is not detected within 3 sec. Jam 88. C8180 DF-720 Rear Side Registration Motor Problem. During initial rotations home position is not detected within 106 pulses. When the rear side home position sensor is turned off during initialization, the sensor did not turn on within 3 sec. C8190 DF-720 Trailing Edge Registration Motor Problem. During initial rotations home position is not detected within 106 pulses. When the trailing edge home position sensor is turned off during initialization, the sensor did not turn on within 3 sec. C8210 DF-710 Stapler Moving Motor 1 Error. During initial rotations home position is not detected within 1.5 sec. C8210 DF-720 Finisher Stapler Problem. Stapler home position sensor does not change state from non-detect to detect within 200ms of forward (CCW) rotation. During initial rotations stapler home position detection does not change state from non-detect to detect within 600ms of reverse (CW) rotation. C8210 DF-730 Stapler Problem. Home position is not detected within a specific time of activation. C8220 DF-710 Stapler Moving Motor 2 Error. During initial rotations home position is not detected within 3.5 sec. C8230 DF-710 Stapler Motor Problem. Jam 82 is indicated. C8300 BF-710 Centerfold Unit Communiation Error. Although the connection is detected, communication is not possible with the centerfold unit. C8310 BF-710 Centerfold Side Registration Motor 1 Problem. During initial rotations home position is not detected within 1000ms. C8320 BF-710 Centerfold Paper Conveying Belt Motor Problem. During initial rotations home position is not detected within 2500ms. C8330 BF-710 Blade Motor Problem. During initial rotations home position is not detected within 1500ms. C8340 BF-710 Centerfold Staple Motor Problem. Jam 89. C8350 BF-710 Centerfold Side Registration Motor 2 Problem. During initial rotations home position is not detected within 1000ms. C8360 BF-710 Centerfold Main Motor Problem. The motor lock signal is detected for more than 1000ms during activation. C8440 DF-730 Sensor Adjusting Problem. The paper entry sensor cannot be adjusted within the specified range. C8460 DF-730 EEPROM Problem. Reading to or writing from EEPROM cannot be performed. C8500 MT-710 Communication Error. The connection is detected, but communication is not possible with the mailbox. C8510 MT-710 Drive Motor Problem. The motor lock signal is detected for more than 500ms during activation. C8800 DF-710 Communication Problem. No communication: there is no reply after (5) tries. Abnormal communication: a parity or checksum error is detected (5) times in succession. C8900 DF-710 Backup Memory Data Problem. Read and write data does not match. C8910 PH-5A Backup Memory Data Problem. Read and write data does not match. C8920 MT-710 Backup Memory Data Problem. Read and write data does not match. C8930 BF-710 Backup Memory Data Problem. Read and write data does not match. C9000 DP-700 Communication Problem. A communication error is detected. C9040 DP-700 Lift Motor Ascent Error. The DP lift upper limit switch is not detected within 10000 pulses. After a one time retry, the DP lift upper limit switch could not be turned On. C9050 DP-700 Lift Motor Descent Error. The DP lift lower limit switch is not detected within 10000 pulses. After a one time retry, the DP lift lower limit switch could not be turned On. C9060 DP-700 EEPROM Error. Read and write data does not match. Data in the specified area of the backup memory does not match the specified values. C9070 DP-700 Communication Error between the DP and SHD. A communication error is detected. C9080 DP-700 Communication Error between the DP and CIS. Reading cannot be performed correctly. CF000 Operation Panel PWB Communication Error/System Error. Unknown error. Communication error between panel and main controller. (If CF620 occurred and is left, CF000 also occurred because of timeout control. CF010 Main PWB Checksum Error/System Error. Communication error between panel and main controller. CF020 Memory Checksum Error/Operation System Error. CF030 Main PWB System Error. CF040 Engine PWB Communication Error. CF041 Scanner PWB Communication Error. CF050 Engine ROM Checksum Error. CF060 Engine RAM Error. CF070 Flash ROM Error. Defective flash ROM (which?). CF080 Flash ROM Error (during download). Defective flash ROM (which?). CF090 Fax System M Communication Error. CF14F Power Source Secondary Side Error/Operation System Error. The operation decomes unstable after recovering the power supply fail (brownout or power drop). Wall voltage is unstable or the main power supply switch was turned OFF/ON within 1 sec. CF256 Fax System M IOBL error or KUIOLIB error. Poor contact at the fax card card due to mis-installation. CF257 Fax System M IOBL error or KUIOLIB error. Poor contact at the fax card card due to mis-installation. CF26F Print System Other Errors. Bug of v.2.03B has been fixed by v. 2.04A (Booklet > Booklet Print). CF3xx Undefined. CF423 Fax System M Error. Wrong data or value detected when the following function is used. Or poor contact at fax card due to mis-installation. CF423 Fax System M Error. The IF error detects during system authentication from ACT_Account_Manager. Or poor contact at fax card due to mis-installation. CF433 CF434 CF437 CF43F CF441 CF444 CF445 CF451 HDD Image Process Error. Destruction of stored jobs on the HDD. It may occur when selecting the keys for calling stored copy or scanner job from a custom box. CF45F CF453 CF454 CF45F CF460 CF463 CF46F CF470 HDD Image Process Error. Destruction of stored jobs on the HDD. It may occur when selecting the keys for calling stored copy or scanner job from a custom box. CF473 CF47F CF484 CF487 CF48F CF490 CF493 CF494 HDD Image Process Error. Destruction of stored jobs on the HDD. It may occur when selecting the keys for calling stored copy or scanner job from a custom box. CF5xx Undefined. CF610 System Start Error. CF620 System Error. Error acquiring the event data. Panel detects CF000 as same error. CF620 System Error. Error acquiring the event data. Panel detects CF000 as same error. Unable to Load Files To CF Card. CF7D7 Readout Error of SSL (authentication data). CFAxx HDD Error. CFB2C CFB30 CFB31 Panel Error. NetFont error. Communication error between panel and main controller during initialization or rejection of communication by controller during initialization. Blue Screen of Death. CFB30 Incompatible Level Of Firmware on Main EEPROM. CFB31 Corrupt Firmware on Main EEPROM. CFB32 Panel Error. Timeout request for start up command. Start command hasn’t been received. Possible destruction of system file in HDD. Cannot enter maintenance mode. Blue Screen of Death. CFB33 Panel Error. Detects disconnection with controller. Possible overdrive of control board or destruction of system file in HDD. Cannot enter maintenance mode. Blue Screen of Death. F000 Operation Panel PWB Communication Error. F010 Main PWB Checksum Error. F020 Memory Checksum Error. F030 Main PWB System Error. F040 Engine PWB Communication Error. F041 Scanner PWB Communication Error. F050 Engine ROM Checksum Error. F060 Engine RAM Error. F070 Flash ROM Error. F080 Flash ROM Error (during download). F090 Fax Control PWB Communication Error. F14F Power Source PWB Second Side Error. E00000 or U00000 Fax Communication Error: No response or line busy after the set number of redials. E00100 or U00100 Fax Communication Error: Transmission was interruped by a press of the Stop/Clear key. E00200 or U00200 Fax Communication Error: Reception was interrupted by a press of the Stop/Clear key. E00300 or U00300 Fax Communication Error: Recording paper on the destination unit has run out during reception. E00420 or U00420 Fax Communication Error: A relay request was received from the host center but interrupted because of a mismatch in permit ID or telephone number. E00421 or U00421 Fax Communication Error: Subaddress-based relay reception was interrupted because of a mismatch in the specified subaddress relay box number. E00430 or U00430 Fax Communication Error: Polling request (confidential or reverse polling) was received but interrupted because of a mismatch in the permit number. E00430 or U00430 Fax Communication Error: Subaddress-based bulletin board transmission was interrupted because of a mismatch in the permit ID of the transmitting unit. E00431 or U00431 Fax Communication Error: Confidential polling transmission was interrupted because the specified confidential box number was not registered. E00431 or U00431 Fax Communication Error: A subaddress-based bulletin board transmission was interrupted because the specified subaddress confidential box was not registered. E00432 or U00432 Fax Communication Error: Confidential polling transmission was interrupted because of a mismatch in the confidential box ID number. E00432 or U00432 Fax Communication Error: A subaddress-based bulletin board transmission was interrupted because of a mismatch in the subaddress confidential box number. E00433 or U00433 Fax Communication Error: Confidential polling request was received but data was not present in the confidential box. E00433 or U00433 Fax Communication Error: Subaddress-based bulletin board transmission request was received but data was not present in the subaddress confidential box. E00434 or U00434 Fax Communication Error: Confidential polling request was received but interrupted because the specified confidential box number was intended for encryption. E00435 or U00435 Fax Communication Error: Confidential polling request was received but interrupted because the specified confidential box was being accessed. E00435 or U00435 Fax Communication Error: Subaddress-based bulletin board transmission request was received but interrupted because the specific subaddress confidential box was being accessed. E00440 or U00440 Fax Communication Error: Confidential reception was interrupted because the specified confidential box number was not registered. E00440 or U00440 Fax Communication Error: Subaddress-based confidential reception or subaddress-based relay reception was interrupted because the specific subaddress box was not registered. E00440 or U00440 Fax Communication Error: Subaddress-based confidential reception or subaddress-based relay command reception was interrupted because the specific subaddress box number was being accessed. E00441 or U00441 Fax Communication Error: Confidential reception was interrupted because the specified confidential box number was intended for encryption. E00450 or U00450 Fax Communication Error: The destination transmitter disconnected because the permit IDs did not agree while the destination transitter is in password-check transmission or restricted transmission. E00460 or U00460 Fax Communication Error: Encrypted reception was interrupted because the specified encryption box number was not registered. E00460 or U00460 Fax Communication Error: Ecrypted reception request was received but interrupted because the specified encryption box was being accessed. E00462 or U00462 Fax Communication Error: Ecryption reception was interrupted because the encryption key for the specified encryption box was not registered. E00500 or U00500 Fax Communication Error: Multiple communication was interrupted and the call was not made on destination units after interruption. E00600 or U00600 Fax Communication Error: The document processor cover is open. E00601 or U00601 Fax Communication Error: Document jam or the document length exceeds the maximum. E00602 or U00602 Fax Communication Error: Image scanning section problem E00603 or U00603 Fax Communication Error: No document feed. E00604 or U00604 Fax Communication Error: Document length exceeded the limit of the bitmap memory capacity. E00610 or U00610 Fax Communication Error: Recording section cover open. E00611 or U00611 Fax Communication Error: Recording paper jam. E00613 or U00613 Fax Communication Error: Image writing section problem. E00614 or U00614 Fax Communication Error: Nearly empty of recording paper. E00615 or U00615 Fax Communication Error: Empty of recording paper. E00620 or U00620 Fax Communication Error: Copier fixing unit problem. E00622 or U00622 Fax Communication Error: Copier drive motor problem. E00655 or U00655 Fax Communication Error: CTS was not activated after RTS due to a modem error. E00656 or U00656 Fax Communication Error: Data was not transmitted after CTS was activated due to a modem error. E00670 or U00670 Fax Communication Error: Power was cut off during communication. E00677 or U00677 Fax Communication Error: There was no file to transmit in the memory transmission mode. E00690 or U00690 Fax Communication Error: System error. E00700 or U00700 Fax Communication Error: Communication was interrupted because of a problem in the destination unit. E00800 or U00800 Fax Communication Error: A page transmission error occurred in G3 mode, because of reception of a RTN or PIN signal. E00810 or U00810 Fax Communication Error: A page transmission error re-occurred in G3 mode after retry of transmission in ECM mode. E00900 or U00900 Fax Communication Error: A page reception error occurred in G3 mode. An RTN or PIN signal was transmitted because of a page reception error. E00910 or U00910 Fax Communication Error: A page reception error occurred in G3 mode. A page reception error remained after retry of transmission in ECM mode. E01000 or U01000 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. An FTT signal was received for a set number of times after TCF signal transmissions at 2400bps. E01000 or U01000 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. An RTN signal was received in response to a Q signal (excluding EOP) after transmission at 2400bps. E01001 or U01001 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. The function of the unit differs from that indicated by a DIS signal. E01010 or U01010 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a DNL (MPS or EOM) signal, and the preset number of command retransfers was exceeded (between units of our make). E01011 or U01011 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a DCS, TCF signal, and the preset number of command retransfers was exceeded. E01012 or U01012 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an NSS1, NSS2 (TCF) signal, and the preset number of command retransfers was exceeded (between units of our make). E01013 or U01013 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an NSS3, TCF signal, and the preset number of command retransfers was exceeded (between units of our make). E01014 or U01014 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an MPS signal, and the preset number of command retransfers was exceeded. E01015 or U01015 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an EOM signal, and the preset number of command retransfers was exceeded. E01016 or U01016 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. An MCF signal was received but no DIS signal was received after transmission of an EOM signal, and T1 timeout was detected. E01017 or U01017 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an EOP signal, and the preset number of command retransfers was exceeded. E01018 or U01018 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PRI-EOP signal, and the preset number of command retransfers was exceeded. E01019 or U01019 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a CNC signal, and the preset number of command retransfers was exceeded (between units of our make). E01020 or U01020 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a CTC signal, and the preset number of command retransfers was exceeded (ECM). E01021 or U01021 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an EOR.Q signal, and the preset number of command retransfers was exceeded (ECM). E01022 or U01022 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a RR signal, and the preset number of command retransfers was exceeded (ECM). E01023 or U01023 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PS.NULL signal, and the preset number of command retransfers was exceeded (ECM). E01024 or U01024 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.MPS signal, and the preset number of command retransfers was exceeded (ECM). E01025 or U01025 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.EOM signal, and the preset number of command retransfers was exceeded (ECM). E01026 or U01026 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.EOP signal, and the preset number of command retransfers was exceeded (ECM). E01027 or U01027 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.PRI-EOP signal, and the preset number of command retransfers was exceeded (ECM). E01028 or U01028 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. T5 timeout was detected during ECM Transmission (ECM). E01040 or U01040 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received during standby for DIS signal reception. E01041 or U01041 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DNL (MPS or EOM) signal (between units of our make). E01042 or U01042 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DCS, TCF signal. E01043 or U01043 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an NSS1, NSS2 (TCF) signal (between units of our make). E01044 or U01044 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an NSS3, TCF signal (between units of our make). E01045 or U01045 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received after transmission of an MPS signal. E01046 or U01046 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received after transmission of an EOM signal. E01047 or U01047 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received after transmission of an EOP signal. E01048 or U01048 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PRI-EOP signal. E01049 or U01049 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CNC signal (between units of our make). E01050 or U01050 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CTC signal (ECM). E01051 or U01051 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an EOR.Q signal (ECM). E01052 or U01052 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an RR signal (ECM). E01053 or U01053 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.NULL signal (ECM). E01054 or U01054 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.MPS signal (ECM). E01055 or U01055 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.EOM signal (ECM). E01056 or U01056 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.EOP signal (ECM). E01057 or U01057 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.PRI-EOP signal (ECM). E01070 or U01070 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. Polarity reversal was detected during handshake. E01071 or U01071 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. Polarity reversal was detected during message transmission. E01072 or U01072 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A break in loop current was detected during transmission. E01073 or U01073 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. During reverse polling in V.34 mode at the receiver unit, a CM signal was not detected when transmitting after reception. E01080 or U01080 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A PIP signal was received after transmission of a PPS.NULL signal. E01091 or U01091 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. During transmission in V.34 mode, communication was interrupted because a PPR signal was received over (10) times even after reducing the communication speed to the minimum with the symbol speed maintained at the level of connection. E01092 or U01092 Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. During transmission in V.34 mode, communication was interrupted because of an impossible combination of the symbol speed and communication speed. E01100 or U01100 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Function of the unit differs from that indicated by a DCS signal. E01101 or U01101 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Function of the unit (excl. communication mode select) differs from that indicated by an NSS signal. E01102 or U01102 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DTC (NSC) signal was received when no transmission data was in the unit. E01110 or U01110 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a DIS signal. E01111 or U01111 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a DTC (NSC) signal. E01112 or U01112 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No training reception after reception of a DCS or NSS signal. E01113 or U01113 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an FTT signal. E01114 or U01114 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of a CFR signal. E01115 or U01115 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of an MCF signal. E01116 or U01116 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of a PPR signal. E01117 or U01117 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of a CTR signal. E01118 or U01118 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of an ERR signal. E01119 or U01119 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No further signals were received after reception of a message. E01120 or U01120 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an MCF signal. E01121 or U01121 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an RTP signal. E01122 or U01122 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an RTN signal. E01123 or U01123 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a PIP signal. E01124 or U01124 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a PIN signal. E01125 or U01125 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a CNS signal (between units of our make). E01126 or U01126 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a PPR signal (ECM). E01127 or U01127 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an ERR signal (ECM). E01128 or U01128 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an RNR signal (ECM). E01129 or U01129 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an SPA signal (short protocol). E01140 or U01140 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DIS signal. E01141 or U01141 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DTC signal. E01142 or U01142 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DCS or NSS signal. E01143 or U01143 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an FTT signal. E01144 or U01144 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CFR signal. E01145 or U01145 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after reception of a message. E01146 or U01146 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an MCF signal (interoffice communication after reception of an MPS, EOM signal or confidential interoffice communication). E01147 or U01147 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an RTP signal. E01148 or U01148 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an RTN signal. E01149 or U01149 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PIPsignal. E01150 or U01150 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PIN signal. E01151 or U01151 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPR signal (ECM). E01152 or U01152 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CTR signal (ECM). E01153 or U01153 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an ERR signal (ECM). E01154 or U01154 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an PNP signal (ECM). E01155 or U01155 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an SPA signal (short protocol). E01160 or U01160 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. During message reception, transmission time exceeded the maximum transmission time per line. E01161 or U01161 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Number of error lines exceeded limits during message reception. E01162 or U01162 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A break in loop current was detected during message reception. E01163 or U01163 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Polarity reversal was detected during message reception. E01164 or U01164 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. One page length exceeded the specified length during message reception. E01170 or U01170 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A decoding error occurred during MMR message reception. E01172 or U01172 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. During reverse polling in V.34 mode at the transmitting unit, a JM signal was not detected after transmission of a CM signal when receiving after transmission. E01191 or U01191 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Communication was interrupted because an error occurred during an image data reception sequence in the V.34 mode. E01199 or U01199 Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DIS signal with different FIF was received after transmission of a DIS signal. E01400 or U01400 Fax Communication Error: An invalid one-touch key was specified during communication. E01500 or U01500 Fax Communication Error: A communication error occurred when calling in V.8 mode. E01600 or U01600 Fax Communication Error: A communication error occurred when called in V.8 mode. E01700 or U01700 Fax Communication Error: A communication error occurred in phase 2 (line probing) in the period after transmission of INFO0, before entering phase 3 (primary channel equivalent device training), before starting T.30 protocol, during transmission in V.34 mode. For example: INFO0/A/Abar (B/Bbar, for polling transmission)/INFOh was not detected. E01720 or U01720 Fax Communication Error: A communication error occurred in phase 4 (modem parameter exchange) in the period after initiating the control channel, before starting T.30 protocol, during transmission in V.34 mode. For example: PPh/ALT/MPh/E was not detected. E01721 or U01721 Fax Communication Error: A communication error occurred before starting T.30 protocol during transmission in V.34 mode. Operation was interrupted due to the absence of a common communication speed between the units. 1) A DCN signal was received from the destination unit and the line was cut, or 2) a DIS (NSF, CSI) signal was received from the destination unit and in response to the signal, the unit transmitted a DCN signal and the line was cut. E01800 or U01800 Fax Communication Error: A communication error occurred in phase 2 (line probing) in the period after transmission of INFO0, before entering phase 3 (primary channel equivalent device training), before starting T.30 protocol during reception in V.34 mode. For example: INFO0/B/Bbar (A/Abar, for polling reception)/probing tone was not detected. E01810 or U01810 Fax Communication Error: A communication error occurred in phase 3 (primary channel equivalent device training), before starting T.30 protocol during reception in V.34 mode. For example: S/Sbar/PP/TRN was not detected. E01820 or U01820 Fax Communication Error: A communication error occurred in phase 4 (modem parameter exchange) in the period after initiating the control channel, before starting T.30 protocol during reception in V.34 mode. For example: PPh/ALT/MPh/E was not detected. E02000 or U02000 Fax Communication Error: Relay broadcast was refused by a relay station because of a mismatch in permit ID number and permit telephone number when a relay command was used. E02100 or U02100 Fax Communication Error: A relay command failed because the destination unit (relay station) had no relay broadcast capability. E02200 or U02200 Fax Communication Error: A relay command from a command station failed because a telephone number was not registered in the relay station was specified. E02200 or U02200 Fax Communication Error: Relay broadcast was requested to a relay station but failed because a telephone number was not registered in the relay station was specified. E02200 or U02200 Fax Communication Error: Subaddress-based relay broadcast transmission failed because the data registered in the subaddress relay box was deleted. E02303 or U02303 Fax Communication Error: Receiving station information was not normally received in reception of a relay command. Timeout was detected before a correct DNL signal was received. E02304 or U02304 Fax Communication Error: Receiving station information was not normally received in reception of a relay command. A signal other than MPS or EOM signal was received after a DNL signal was received. E02400 or U02400 Fax Communication Error: An interoffice subaddress-based relay transmission was interrupted because of a mismatch in the specified relay box number. E03000 or U03000 Fax Communication Error: No document was present in the destination unit when polling reception started. E03100 or U03100 Fax Communication Error: In reverse polling, although no original was set in the destination unit, transmission was complete. E03200 or U03200 Fax Communication Error: In confidential polling reception, data was not accumulated in the specified box in the destination unit. E03200 or U03200 Fax Communication Error: In interoffice subaddress-based bulletin board reception, data was not stored in the box specified by the destination unit. E03300 or U03300 Fax Communication Error: In polling reception from a unit of our make, operation was interrupted due to a mismatch in permit ID number or telephone number. E03300 or U03300 Fax Communication Error: In interoffice subaddress-based bulletin board reception, operation was interrupted due to a mismatch in permit ID number or telephone number. E03400 or U03400 Fax Communication Error: Polling reception was interupted because of a mismatch in individual numbers. E03500 or U03500 Fax Communication Error: In confidential polling reception, the specified confidential box number was not registered in the destination. E03500 or U03500 Fax Communication Error: In interoffice subaddress-based bulletin board reception, the specified subaddress confidential box number was not registered in the destination unit. E03500 or U03500 Fax Communication Error: The destination was being accessed. E03600 or U03600 Fax Communication Error: Confidential polling reception was interrupted because of a mismatch in specified confidential box numbers. E03600 or U03600 Fax Communication Error: An interoffice subaddress-based bulletin board reception was interrupted because of a mismatch in the specified subaddress confidential box number. E03700 or U03700 Fax Communication Error: Confidential polling reception failed because the destination unit had no confidential polling transmission capability or data was not accumulated in any box in the destination unit. E03700 or U03700 Fax Communication Error: Interoffice subaddress-based bulletin board reception failed because the destination unit had no subaddress-based bulletin board transmission capability, or data was not stored in any subaddress confidental box in the destination unit. E04000 or U04000 Fax Communication Error: The confidential box specified for confidential transmission was not registered in the destination unit. E04000 or U04000 Fax Communication Error: In interoffice subaddress-based transmission mode, the specified subaddress box number was not registered in the destination unit. E04000 or U04000 Fax Communication Error: The destination was being accessed. E04100 or U04100 Fax Communication Error: Confidential transmission failed because the destination unit had no confidential capability. E04100 or U04100 Fax Communication Error: Subaddress-based transmission failed because the destination unit had no subaddress-based reception capability. E04200 or U04200 Fax Communication Error: In encrypted tranmission, the specified encryption box was not registered in the destination unit. E04300 or U04300 Fax Communication Error: Encrypted transmission failed because the destination unit had no encrypted communication capability. E04400 or U04400 Fax Communication Error: Communication was interrupted because of an encryption key error during encrypted transmission. Encryption keys did not agree. E04401 or U04401 Fax Communication Error: Communication was interrupted because of an encryption key error during encrypted trasmission. The encryption key was not registered. E04500 or U04500 Fax Communication Error: Encrypted reception was interrupted because of a mismatch in ecryption keys. E05000 or U05000 Fax Communication Error: In transmission with a specified number, the set number of originals was different from the number of transmitted originals. E05100 or U05100 Fax Communication Error: Password check transmission or restricted transmission was interrupted because the permit ID numbers did not match. E05200 or U05200 Fax Communication Error: Password check reception or restricted reception was interrupted because the permit ID numbers did not match, the rejected fax numbers did match, or the destination receiver did not return its phone number. E05300 or U05300 Fax Communication Error: Password check reception or restricted reception was interrupted because the permitted numbers did not match, the rejected numbers did match, or the machine in question did not acknowledge its phone number. E09000 or U09000 Fax Communication Error: G3 communication was attempted but failed because the destination unit was a G2 machine. E12000 or U12000 Fax Communication Error: Relay broadcast was requested from a command station but memory overflowed during reception. E12000 or U12000 Fax Communication Error: In subaddress-based relay reception memory overflowed. E12100 or U12100 Fax Communication Error: Relay was commanded but memory overflowed in the destination unit (relay station). E14000 or U14000 Fax Communication Error: Memory overflowed during confidential reception. E14000 or U14000 Fax Communication Error: Memory overflowed in subaddress-based confidential reception. E14100 or U14100 Fax Communication Error: Memory overflowed in the destination unit during confidential transmission. E14100 or U14100 Fax Communication Error: Memory overflowed in the destination unit during interoffice subaddress-based transmission. E19000 or U19000 Fax Communication Error: Memory overflowed during memory reception. E19100 or U19100 Fax Communication Error: Memory overflowed in the destination unit during transmission. E19200 or U19200 Fax Communication Error: Memory transmission failed because a decoding error occurred. E19300 or U19300 Fax Communication Error: Transmission failed because an error occurred during JBIG encoding. E19400 or U19400 Fax Communication Error: Reception failed because an error occurred during JBIG encoding. Send SMB Error 1102 Error: Username/Password or Shared Name/Folder Name. Domain name is not entered. Send SMB Error 1102 Error: Username/Password or Shared Name/Folder Name. Assign disable user/password. Send SMB Error 1102 Error: Username/Password or Shared Name/Folder Name. Assign the user who is not allowed to access the folder. Send SMB Error 1102 Error: Username/Password or Shared Name/Folder Name. Assign disable shared name. Send SMB Error 1102 Error: Username/Password or Shared Name/Folder Name. Host name error. Send SMB Error 1103 Error: Pathname or File Name. Domain name is not entered. Send SMB Error 1103 Error: Pathname or File Name. Connect to the folder which is not permitted for reference/writing. Send SMB Error 1103 Error: Pathname or File Name. Assign disable folder path. Send SMB Error 1105 Error: Not Supported Protocol. SMB protocol is set to OFF. Send SMB Error 2101 Error: Can Not Connect. Enter the disable host name/IP address. Send SMB Error 2101 Error: Can Not Connect. Assign the wrong port number. Send SMB Error 2101 Error: Can Not Connect. Network is not connected. Send SMB Error 2103 Error: Response Wait With Timeout. The server is unable to communicate. Send SMB Error 2201 Error: Network Transfer. Error occurs on the network. Send SMB Error 2203 Error: Response Wait With Timeout. Response is not returned from the server, above specified time. Send SMB Error 9181 Error: Page Max Count Over. The number of pages of a send file exceeds 999 pages. Send FTP Error 1101 Error: Host Name. Enter the disable host name/IP address. Send FTP Error 1102 Error: Username/Password. Domain name is not entered. Send FTP Error 1102 Error: Username/Password. Assign disable user/password. Send FTP Error 1103 Error: Pathname or File Name. Connect to the folder which is not permitted for reference/writing. Send FTP Error 1103 Error: Pathname or File Name. Assign disable folder path. Send FTP Error 1105 Error: Not Supported Protocol. FTP protocol is set to OFF. Send FTP Error 2101 Error: Can Not Connect. Enter the disable host name/IP address. Send FTP Error 2101 Error: Can Not Connect. Assign the wrong port number. Send FTP Error 2101 Error: Can Not Connect. Network is not connected. Send FTP Error 2102 Error: Cannot Connect With Timeout. The server is unable to communicate. Send FTP Error 2102 Error: Cannot Connect With Timeout. Send the server which does not support FTP server. Send FTP Error 2103 Error: Response Wait With Timeout. The server is unable to communicate. Send FTP Error 2201 Error: Network Transfer. Error occurs on the network. Send FTP Error 2202 Error: Network Transfer With Timeout. Error occurs on the network. Send FTP Error 2203 Error: Response Wait With Timeout. Response is not returned from the server, above specified time. Send FTP Error 3101 Error: Server Response. The server is error status. Send FTP Error 9181 Error: Page Max Count Over. The number of pages of a send file exceeds 999 pages. Send email Error 1101 Error: Host Name. SMTP server name is not set. Error SMTP server name. Send email Error 1102 Error: Username/Password. User ID for the authentication is not entered or entered wrongly. Wrong authentication password is entered. Send email Error 1104 Error: No Recipient Address. The destination address is not specified. Send email Error 1105 Error: Not Supported Protocol. SMTP protocol is set to OFF. Send email Error 1106 Error: No Sender Info. Sender address is not entered. Send email Error 2101 Error: Can Not Connect. Select [Other Authenticate] when authenticating POP before SMTP. Send email Error 2101 Error: Can Not Connect. The specified server is not SMTP server. Send email Error 2101 Error: Can Not Connect. Network is not connected. Send email Error 2102 Error: Cannot Connect With Timeout. The server is unable to communicate. Send email Error 2103 Error: Response Wait With Timeout. The server is unable to communicate. Send email Error 2201 Error: Network Transfer. Error occurs on the network. Send email Error 2202 Error: Network Transfer With Timeout. Error occurs on the network. Send email Error 2203 Error: Response Wait With Timeout. Response is not returned from the server, above specified time. Send email Error 2204 Error: Email Size Limit. The size of the email attachment exceeds its limit. Send email Error 3101 Error: Server Response. The server is error status. Send email Error 3101 Error: Server Response. Server setting is not authenticated normally. Send email Error 3201 Error: Not Found Authentication Mechanism. Unsupported SMTP Authentication Mechanism is found. Send email Error 9181 Error: Page Max Count Over. The number of pages of a send file exceeds 999 pages. TWAIN Error 2202 Error: Network Transfer With Timeout. Response is not returned from the server, above the specified time. TWAIN Error 9181 Error: Page Max Count Over. The number of pages of a send file exceeds 999 pages. Software Error 5101 Error: Not Yet Connected. Operation handle error. Error for stored status in the operation handle. Software Error 5102 Error: Already Connected. Operation handle error. Error for stored status in the operation handle. Software Error 5103 Error: Not Yet Opened. Error for storage status in the operation handle. Software Error 5104 Error: Already Opened. Error for storage status in the operation handle. Software Error 7101 Error: Memory Allocation. Insufficient memory space. Software Error 7102 Error: Socket Create. Unable to create a communication socket. Software Error 720f Error: Unknown Error. Unable to determine the cause. Send error. Job is cancelled. Press [End]. 1101 Send Email Error: Host Name. SMTP server name is not set. Error SMTP server name. Send error. Job is cancelled. Press [End]. 1101 Send FTP Error: Host Name. Enter the disable host name/IP address. Send error. Job is cancelled. Press [End]. 1102 Send Email Error: Username/Password. User ID for the authentication is not entered or entered wrongly. Wrong authentication password is entered. Send error. Job is cancelled. Press [End]. 1102 Send SMB/FTP Error: Username/Password or Shared Name/Folder Name. Domain name is not entered. Send error. Job is cancelled. Press [End]. 1102 Send SMB/FTP Error: Username/Password or Shared Name/Folder Name. Assign disable user/password. Send error. Job is cancelled. Press [End]. 1102 Send SMB Error: Username/Password or Shared Name/Folder Name. Assign disable shared name. Send error. Job is cancelled. Press [End]. 1102 Send SMB Error: Username/Password or Shared Name/Folder Name. Host name error. Send error. Job is cancelled. Press [End]. 1103 Send SMB/FTP Error: Pathname or File Name. Domain name is not entered. Send error. Job is cancelled. Press [End]. 1103 Send SMB/FTP Error: Pathname or File Name. Connect to the folder which is not permitted for reference/writing. Send error. Job is cancelled. Press [End]. 1103 Send SMB/FTP Error: Pathname or File Name. Assign disable folder path. Send error. Job is cancelled. Press [End]. 1104 Send Email Error: No Recipient Address. The destination address is not specified. Send error. Job is cancelled. Press [End]. 1105 Send Email Error: Not Supported Protocol. SMTP protocol is set to OFF. Send error. Job is cancelled. Press [End]. 1105 Send SMB Error: Not Supported Protocol. SMB protocol is set to OFF. Send error. Job is cancelled. Press [End]. 1105 Send FTP Error: Not Supported Protocol. FTP protocol is set to OFF. Send error. Job is cancelled. Press [End]. 1106 Send Email Error: No Sender Info. Sender address is not entered. Send error. Job is cancelled. Press [End]. 2101 Send Email Error: Can Not Connect. Network is not connected. Send error. Job is cancelled. Press [End]. 2101 Send Email Error: Can Not Connect. Select [Other Authenticate] when authenticating POP before SMTP. Send error. Job is cancelled. Press [End]. 2101 Send Email Error: Can Not Connect. The specified server is not SMTP server. Send error. Job is cancelled. Press [End]. 2101 Send SMB/FTP Error: Can Not Connect. Enter the disable host name/IP address. Send error. Job is cancelled. Press [End]. 2101 Send SMB/FTP Error: Can Not Connect. Assign the wrong port number. Send error. Job is cancelled. Press [End]. 2101 Send SMB/FTP Error: Can Not Connect. Network is not connected. Send error. Job is cancelled. Press [End]. 2102 Send Email/ FTP Error: Cannot Connect With Timeout. The server is unable to communicate. Send error. Job is cancelled. Press [End]. 2102 Send FTP Error: Cannot Connect With Timeout. Send the server which does not support FTP server. Send error. Job is cancelled. Press [End]. 2103 Send Email/ SMB/ FTP Error: Response Wait With Timeout. The server is unable to communicate. Send error. Job is cancelled. Press [End]. 2201 Send Email/ SMB/ FTP Error: Network Transfer. Error occurs on the network. Send error. Job is cancelled. Press [End]. 2202 Send Email/FTP Error: Network Transfer With Timeout. Error occurs on the network. Send error. Job is cancelled. Press [End]. 2202 Send TWAIN Error: Network Transfer With Timeout. Response is not returned from the server, above the specified time. Send error. Job is cancelled. Press [End]. 2203 Send Email/FTP Error: Response Wait With Timeout. Response is not returned from the server, above specified time. Send error. Job is cancelled. Press [End]. 2204 Send Email Error: Email Size Limit. The size of the email attachment exceeds its limit. Send error. Job is cancelled. Press [End]. 3101 Send Email/FTP Error: Server Response. The server is error status. Send error. Job is cancelled. Press [End]. 3101 Send Email Error: Server Response. Server setting is not authenticated normally. Send error. Job is cancelled. Press [End]. 3201 Send Email Error: Not Found Authentication Mechanism. Unsupported SMTP Authentication Mechanism is found. Send error. Job is cancelled. Press [End]. 5101 Send Software Error: Not Yet Connected. Operation handle error. Error for stored status in the operation handle. Send error. Job is cancelled. Press [End]. 5102 Send Software Error: Already Connected. Operation handle error. Error for stored status in the operation handle. Send error. Job is cancelled. Press [End]. 5103 Send SoftwareError: Not Yet Opened. Error for storage status in the operation handle. Send error. Job is cancelled. Press [End]. 5104 Send Software Error: Already Opened. Error for storage status in the operation handle. Send error. Job is cancelled. Press [End]. 7102 Send Software Error: Socket Create. Unable to create a communication socket. Send error. Job is cancelled. Press [End]. 720f Send Software Error: Unknown Error. Unable to determine the cause. Send error. Job is cancelled. Press [End]. 9181 Send Email/ SMB/ FTP/ TWAIN Error: Page Max Count Over. The number of pages of a send file exceeds 999 pages. «Acceptable staple count exceeded.» Is the acceptable staple count exceeded? «Add paper in cassette #.» Is the indicated cassette out of paper? «Add paper in MP tray.» Is the paper of the specified size loaded in the multipurpose tray? «Add staples.» Has the document finisher run out of staples? «Add toner.»   «An error has occurred.» An internal error has occurred.Make a note of the error code number displayed on the panel. See above. «Box Limit Exceeded.» Document Box is full, and no further storage is available; Job is cancelled. Repeat Copy Box is full, and no further repeat copy is available. «Cannot connect to Authentication Server.»   «Cannot duplex print on this paper.» Did you select a paper size/type that cannot be duplex printed? «Cannot execute this job.» Job is restricted by Job Accounting. «Cannot offset this paper.» Did you select a paper size that cannot be offset (A3, B4, A5R, B6R, Folio, Ledger, Statement, & 8K)? «Cannot punch this paper type.» Did you select a paper size/type that cannot be punched? «Cannot staple this paper.» Did you select a paper size/type that cannot be stapled? «Check the cover.» Are any covers open? Does the message indicate which cover is open? «Check the document processor.» Is the document processor open? Is the top cover of the document processor open? «Check the finisher.» Is the document finisher set correctly?» «Clean the slit glass.» Dirt has been identified on the slit glass. «Empty the punch waste box.» The punch waste box of the 3,000 sheet finisher is full. «Failed to specify Job Accounting.» Job accounting is not specified in the print driver. «Failed to store job retention data.»   «Fax box limit exceeded.» Fax box is full, and no further storage is available. «Finisher tray is full of paper.» Is the acceptable storage capacity exceeded for the document finisher tray?» «Folding tray is full of paper.» Is the acceptable storage capacity exceeded for the folding tray of the 3,000 sheet document finisher?» «Hard Disk error. Job is cancelled. Press [End] ##» An error has occurred on the hard disk. «Incorrect Login User Name or Password.»   «Job Accounting restriction exceeded.» The print count exceeded the acceptable count restricted by Job Accounting. «Job Separator is full of paper.» Is the maximum capacity of the job separator tray exceeded? «KPDL error.» A PostScript error has occurred. «Mailbox tray is full of paper.»   «Memory card error.» Was the memory card (Compact Flash) removed while being accessed? Was a valid memory card inserted? «Memory card error. Job is cancelled. Press [End]. Code: 01 Memory Card Error: Format error. «Memory card error. Job is cancelled. Press [End]. Code: 04 Memory Card Error: Insufficient memory card space to complete this operation. «Memory is full.» Unable to continue the job, as the memory is used up.» «Memory Is Low» Logic Lockup «Paper Jam. ###» Make a note of the jam location number displayed on the panel. Leave the machine On. «Print overrun.» Warning. Low printer memory. «Removable memory error.» An error has occurred on the USB stick memory or Compact Flash memory. «Removable memory was removed.»   «Replace all originals and press [Continue].»   «Replace the waste toner box.» The waste toner box is full. «Reset all originals in the document processor.» Are there any originals left in the document processor? «Scanner memory is full.» Scanning cannot be performed due to insufficient memory for the scanner. Is the acceptable scanning count exceeded? «Scanner Paused» DMA transmission of compressed, ecompressed, rotated, relocated, or blanked-out image data does not complete within a specified period of time. «Set the folding tray.» Is the folding tray correctly installed to the 3,000 sheet capacity document finisher? «Set the folding unit.» Is the folding tray correctly installed to the 3,000 sheet capacity document finisher? «Set the punch waste box.» The waste toner box is not installed correctly. «Set the waste toner box.» The waste toner box is not installed correctly. «Staple error.» The location of the jam will be indicated on the panel. Leave the machine On. «Staple jam.» The location of the jam will be indicated on the panel. Leave the machine On. «The ID is not registered.» The account ID# does not match. «The memory card is not formatted.» Is the removable memory formatted by this machine? «The phone receiver is off the hook.»   «The removable memory is not formatted.» Is the removable memory formatted by this machine? «The source file is not found.» The specified file is not found. «Top tray of the machine is full of paper.» The exit tray at the top of the machine is full. «Tray # is full of paper.» Is the acceptable storage capacity exceeded for any of the output trays A, B, or C of the 3,000 sheet capacity document finisher? «Warning low memory.» Further scanning cannot be performed due to insufficient memory.

Error Code Description 0xF330 Component: RIP. Category: RIP. Recovery impossible error (CreatePrint and return back value of API is indirect). 0xF331 Component: RIP. Category: RIP. Fail to initialize. 0xF333 Component: RIP. Category: RIP. Access failure to ME. 0xF335 Component: RIP. Category: RIP. Failure to switch TASK. 0xF336 Component: RIP. Category: RIP. IOBL process failure. 0xFB30 Component: Panel. Category: KI-Panel. Failed to connect the communication of the controller when starting up. Blue back screen. Cannot enter maintenance mode. 0xFB31 Component: Panel. Category: KI-Panel. Refused to connect the communication of the controller when starting up. Blue back screen. Cannot enter maintenance mode. 0xFB32 Component: Panel. Category: KI-Panel. Time to start up request command (start up request command could not be received). Blue back screen. Cannot enter maintenance mode. 0xFB33 Component: Panel. Category: KI-Panel. Cut off of the communication with the controller is detected — waiting to receive: select () OK return, recv() RX data length 0. Blue back screen. Cannot enter maintenance mode. 0xFB34 Component: Panel. Category: KI-Panel. Time out for Response telegraphic message (could not receive response telegraphic message within a fixed time). In case on not through httpd, this error occurs (in case it does not become CGI time out). 0xFB35 Component: Panel. Category: KI-Panel. Received abusive command from controller. At this moment, only the case that unexpected command comes in when wating for the startup request command. 0xFB36 Component: Panel. Category: KI-Panel. Connection error is detected when waiting for he response telegraphic message from the controller. select () function returned the error (other than EINTR). 0xFB37 Component: Panel. Category: KI-Panel. Connection error is detected when waiting for he response telegraphic message from the controller. rcv () function returned the error. 0xFB38 Component: Panel. Category: KI-Panel. Communication error is detected when transferring (using UNIX domain) response telegraphic message in the panel. send() function returned the error (other than EINTR). 0xFB39 Component: Panel. Category: KI-Panel. Crucial error is detected when processing receive/transfer of the response telegraphic message from controller. Failed to acquire semafo??? 0xFB3A Component: Panel. Category: KI-Panel. Communication error is detected when sending required response telegraphic message from panel. send() function returned the error (other than EINTR). CF000 Component: HDD. Failure to initialize with «dbinit, hostif_stat_chg» comand. CF000 Operation panel PWB comunication error. CF010 ROM Checksum Error. CF010 Main PWB Checksum Error/System Error. Communication error between panel and main controller. CF012 ROM Checksum Error. CF020 Memory Checksum Error/Operation System Error. CF030 Main PWB System Error. CF040 Engine PWB Communication Error. CF040 Engine PWB Communication Error. CF041 Scanner PWB Communication Error. CF050 Engine ROM Checksum Error. CF060 Engine RAM Error. CF070 Flash ROM Error. Defective flash ROM (which?). CF080 Flash ROM Error (during download). Defective flash ROM (which?). CF090 Fax System M Communication Error. CF125 Scanner Unit Error CF131 Component: PCM. Category: OS. Failure to initialize with «dbinit, hostif_stat_chg» comand. CF131 Component: PCM. Category: OS. Failure to acquire Entity data with «dbinit, hostif_stat_chg» comand. CF145 Fax Unit Error. CF14F Power Source Secondary Side Error/Operation System Error. The operation decomes unstable after recovering the power supply fail (brownout or power drop). Wall voltage is unstable or the main power supply switch was turned OFF/ON within 1 sec. CF14F Component: OS. Category: OS. Primary supply voltage dropped off temporarily and recovery operation was not stable. If the input power supply voltage is not stable of the Main SW is turned Off/On quickly (about 1 second), this problem occurs. CF186 Print Unit: DVU_PRT_SYSERR_F226_ERROR (Video data flushing error) CF18A Engine Firmware Incompatible. CF18C Document BOX error. CF1FF Component: ScanSys. Category: ScanSys. When the scanner scanning parameter from the topside is in error. CF1FF Component: IPLogical. Category: PrintSystem. Could not obtain instance of Config, SystemStatus. Use below mentioned class: ipl_search_output.cpp, ipl_feeder_spec.cpp, outputcheck.cpp. CF1FF Component: Machine Configuration. Category: PrintSystem. Could not obtain instance of Config, SystemStatus. Use below mentioned class: machine_status_engine.cpp. CF1FF Component: OutputMission. Category: PrintSystem. Increasing and decreasing «Lib», in case that even if there is no original available, tried to process increasing & decreasing. CF1FF Component: OutputMission. Category: PrintSystem. In case to specify some other value (indirect value) other than single sided/duplex/forced duplex for increasing & decreasing «Lib». CF1FF Component: OutputMission. Category: PrintSystem. In case of the address for Job setting value structure is NULL. CF1FF Component: OutputMission. Category: PrintSystem. In case of the code for output completion notice is indirect. CF1FF Component: OutputMission. Category: PrintSystem. When writing the original information to the storage, in case to get the reply back as [Other Error]. CF1FF Component: OutputMission. Category: PrintSystem. In case to get the reply as [Finisher out of order Error], [No Feeder available in search] from Paper feed/eject «Lib». CF1FF Component: OutputMission. Category: PrintSystem. In case to get the reply as failure from rotation calculation «Lib». CF1FF Component: PrintSystem. Category: PrintSystem. Could not obtain instance of Config, SystemStatus. Use below mentioned class: print_startup.cpp. CF1FF Component: SVI. Category: LioPanel. Logical Error (In case of given parameter is NULL). CF214 Codec: GICL_CDC_ERR_FACTOR_JPEG (several hardware error, software error). CF215 Codec: GICL_CDC_ERR_FACTOR_SRLE (several hardware error, software error). CF234 Data conversion error. CF235 Error code when receiving/printing email. CF245 Process Manager: SYS_PRCM_ERR_FACTOR_SVC_PROC_DOWN (Device process down). CF246 Process Manager: SYS_PRCM_ERR_FACTOR_DEV_PROC_DOWN (Device process down). CF247 Process Manager: SYS_PRCM_ERR_FACTOR_JOBIMG_PROC_DOWN (Job image process down). CF247 Component: ScanSys. Category: ScanSys. Library Error inside of ScanSys. CF248 Component: UNKNOWN. Category: UNKNOWN. CF248 Component: UNKNOWN. Category: UNKNOWN. Code present on with Kyocera Barfode Font CF card installed. CF248 Process Manager: SYS_PRCM_ERR_FACTOR_PRN_PROC_DOWN (Printer process down). CF256 Fax System M IOBL error or KUIOLIB error. Poor contact at the fax card card due to mis-installation. CF257 Component: LFM. Category: FaxSys. KUIOLIB error. Poor contact at the fax card card due to mis-installation. CF257 Fax System M IOBL error or KUIOLIB error. Poor contact at the fax card card due to mis-installation. CF25E Network Manager: CF25F Component: LFM. Category: FaxSys. Instance Check Error, Paramemter Error from topside. CF26F Component: PrintSys. Category: PrintSys. It occurs when the error noticed from VideoDriver. Use by Video_Driver class: Function name, factor can be found by the detail code. CF26F Print System Other Errors. Bug of v.2.03B has been fixed by v. 2.04A (Booklet > Booklet Print). CF26F System State Manager: CF278 Energy Saving Manager: CF320 Component: LioFax. Category: FaxSys. An Observer Deletion Error occurred during salvage process. Error received from the method on EventManager or message Tx. CF321 Component: LioFax. Category: FaxSys. Segment code for LioFax initialization is different from «03KH». CF323 Component: LioFax. Category: FaxSys. Return address of Page class when doing FAX Tx/Rx is other abnormal error. Entity (Config, BOX, etc.) access error. CF324 Component: LioFax. Category: FaxSys. Entity parameter error. CF325 Component: LioFax. Category: FaxSys. In case that the time when Error came back from LFM. CF326 Component: LioFax. Category: FaxSys. IOBL error. CF327 Component: LioFax. Category: FaxSys. At the time of KUIOLIB error, CodeChange error, FaxLib error (Sender recorde, Entity related error). CF32F Component: LioFax. Category: FaxSys. Instance Check Error. Parameter Error from topside. CF337 Device Error (scan control): CF3FF Component: RIP. Category: RIP. Other/System Crucial Error. CF423 Component: FaxJOB. Category: FaxSys. As the error came back at IF for DocumentBox, JobInfo, Config Entity. CF423 Component: FaxJob. Category: FaxSys. The error came back when accessing (obtaining data, setting data) to below Entity related: job_ent(JobModel,JobInfo), config_ent, reservation, account(certificate), document_box. CF423 Fax System M Error. Wrong data or value detected when the following function is used. Or poor contact at fax card due to mis-installation. CF423 Fax System M Error. The IF error detects during system authentication from ACT_Account_Manager. Or poor contact at fax card due to mis-installation. CF424 Component: FaxJob. Category: FaxSys. As the error came back when obtaining IF for system authentication from ACT_Account_Manager. CF424 Component: FaxJob. Category: FaxSys. The date obtained from the below Entity related is unexpected data: job_ent(JobInfo). CF427 Component: FaxJob. Category: FaxSys. The error came back for the IF of LioFax observer addition/deletion. CF42F Component: FaxJob. Category: FaxSys. As handing over of the NULL pointer in the class occurred. As memory reservation with new in heap domain is failed: Assert for preventing from segment drop off. CF42F Component: FaxJob. Category: FaxSys. When generating the class, fail new at obtaining data domain, soft logic error (software bug). CF433 Component: NetClient. Category: ImageProcess. Entity Error. CF434 Component: NetClient. Category: ImageProcess. Entity Data Invalid. CF437 Component: NetClient. Category: ImageProcess. Other Library Error (ImageLibrary, PageData, EventManager). CF43F Component: NetClient. Category: ImageProcess. Crucial (no memory, invalid parameter, etc.). CF441 Component: CreateScan. Category: ImageProcess. Initialize Error. CF444 Component: CreateScan. Category: ImageProcess. Entity Data Invalid. CF445 Component: CreateScan. Category: ImageProcess. Middleware Error (LioScanner error). CF451 Component: CreatePrint. Category: ImageProcess. Initialization Error. CF433 CF434 CF437 CF43F CF441 CF444 CF445 CF451 HDD Image Process Error. Destruction of stored jobs on the HDD. It may occur when selecting the keys for calling stored copy or scanner job from a custom box. CF453 Component: CreatePrint. Category: ImageProcess. Entity Error. CF454 Component: CreatePrint. Category: ImageProcess. Entity Data Mismatch. CF45F Component: CreatePrint. Category: ImageProcess. Other Error. CF460 Component: CreateBox (Memory Tx). Category: ImageProcess. Unrecoverable Error. CF463 Component: CreateBox (Memory Tx). Category: ImageProcess. Entity Error. CF46F Component: CreateBox (Memory Tx). Category: ImageProcess. Crucial (no memory, invalid parameter, etc.). CF46F PDL Interpreter: REN_INT_ERR_FACTOR_GENERAL (other general error). CF470 Component: CreateFax. Category: ImageProcess. Unrecoverable Error. CF473 Component: CreateFax. Category: ImageProcess. Entity Error. CF47F Component: CreateFax. Category: ImageProcess. Crucial (no memory, invalid parameter, etc.). CF484 Component: Edit. Category: ImageProcess. Data Invalid (PageData). CF487 Component: Edit. Category: ImageProcess. Other Library Error (ImageLibrary). CF48F Component: Edit. Category: ImageProcess. Crucial. CF490 Component: Output(Fax). Category: ImageProcess. Unrecoverable Error. CF493 Component: Output(Fax). Category: ImageProcess. Entity Error. CF494 Component: Output(Fax). Category: ImageProcess. Entity Data Invalid. CF45F CF453 CF454 CF45F CF460 CF463 CF46F CF470 CF473 CF47F CF484 CF487 CF48F CF490 CF493 CF494 HDD Image Process Error. Destruction of stored jobs on the HDD. It may occur when selecting the keys for calling stored copy or scanner job from a custom box. CF515   CF526 System Error: CF528 Component: SVI. Category: LioPanel. Panel data abusion error. CF530 Component: PJL. Category: RIP. Recovery impossible error: Thread Create failed. CF530 Component: ReportEventService. Category: RIP. Recovery impossible error: Thread Create failed. CF530 Component: SVCTL_FaxRx_Event_Control. Category: KI Sc. As failed to obtain EM_FaxRx_Ec_Event_Fax_Enable. CF530 Component: SVCTL_Reservation_Event_Control. Category: KI Sc. As failed to notice the event for EM_Rsv_EC_op_Event_FaxJob_Ready. CF530 Component: SVCTL_Job_Start_Command. As JobInfo giving to JSM_JobServiceManager is NULL. CF533 Component: PJL. Category: RIP. Entity error: when CLITICAL ERROR occurred at ME access. CF533 Component: ReportEventService. Category: RIP. Entity error: when CLITICAL ERROR occurred at ME access. CF551 Component: MLPRN. Category: NetAppl. Task generation error. CF551 Component: MLPRT. Category: NetAppl. Task generation error. CF551 Component: EVR_LGS. Category: NetAppl. Task generation error. CF610 Component: SSTUP. Category: OS. Error in the SystemStartUp (Thread generation, Entity data acquisition, DiskManager operation). CF610 Undefined. CF610 System Start Error. CF615 Report Page Generator: USV_RPG_ERR_FACTOR_STREAM (Stream access error). CF620 Component: EventManager. Category: KM-Entity. Failed to obtain/receive event from framework. CF620 Unable to Print. CF620 System Error. Error acquiring the event data. Panel detects CF000 as same error. CF620 System Error. Error acquiring the event data. Panel detects CF000 as same error. Unable to Load Files To CF Card. CF630 Component: PowerManagement. Category: OS. Failed to mount or unmount during transition of the condition. CF710 Component: IIS. Category: NetApl. Network file written error (inetd). CF713 Component: IIS. Category: NetApl. Entity error (inetd). CF720 Component: IIS. Category: NetApl. Network file written error (services). CF723 Component: IIS. Category: NetApl. Entity error (services). CF730 Component: IIS. Category: NetApl. Network file written error (snmpd). CF733 Component: IIS. Category: NetApl. Entity error (snmpd). CF743 Component: IIS. Category: NetApl. Entity error (hosts allow). CF750 Component: IIS. Category: NetApl. Network file written error (hostname). CF753 Component: IIS. Category: NetApl. Entity error (hostname). CF760 Component: IIS. Category: NetApl. Network file written error (papd). CF763 Component: IIS. Category: NetApl. Entity error (papd). CF770 Component: IIS. Category: NetApl. Network file written error (cups). CF773 Component: IIS. Category: NetApl. Entity error (cups). CF780 Component: IIS. Category: NetApl. Network file written error (dhcclient). CF783 Component: IIS. Category: NetApl. Entity error (dhcclient). CF790 Component: IIS. Category: NetApl. Network file written error (smb). CF793 Component: IIS. Category: NetApl. Entity error (smb). CF7A0 Component: IIS. Category: NetApl. Network file written error (netware). CF7A3 Component: IIS. Category: NetApl. Entity error (netware). CF7B0 Component: IIS. Category: NetApl. Network file written error (ipfilter). CF7B3 Component: IIS. Category: NetApl. Entity error (ipfilter). CF7C0 Component: IIS. Category: NetApl. Network file written error (ethermode). CF7C3 Component: IIS. Category: NetApl. Entity error (ethermode). CF7D0 Component: IIS. Category: NetApl. Network file written error (other). CF7D3 Component: IIS. Category: NetApl. Entity error (other). CF7D7 Readout Error of SSL (authentication data). CFAxx HDD Error. CFAxx HDD Error. CFA10 Component: OS_TOOLS. Category: OS. Error inside of hot plug detection thread, overwritten thread (failed to issue the event, failed to operate signal handler). CFA20 Component: OS_TOOLS. Category: OS. Failed to obtain memory size. CFA23 Component: OS_TOOLS. Category: OS. Access error to the Entity at master data stored area component. CFA30 Component: OS_TOOLS. Category: OS. CF-DETECT OPEN error <0x07>. CFA30 Component: OS_TOOLS. Category: OS. CF-DETECT IOCTL error <0x08>. CFA30 Component: OS_TOOLS. Category: OS. CF-DETECT CLOSE error <0x09>. CFA30 Component: OS_TOOLS. Category: OS. AES conversion OPEN error <0x0a>. CFA30 Component: OS_TOOLS. Category: OS. AES conversion IOCTL error <0x0b>. CFA30 Component: OS_TOOLS. Category: OS. AES conversion CLOSE error <0x0c>. CFA30 Component: OS_TOOLS. Category: OS. AES conversion command return value error <0x0d>. CFA30 Component: OS_TOOLS. Category: OS. Message queue creation error <0x15>. CFA30 Component: OS_TOOLS. Category: OS. Message queue Tx error <0x16>. CFA30 Component: OS_TOOLS. Category: OS. Message queue Rx error <0x17>. CFA30 Component: OS_TOOLS. Category: OS. Message queue deletion error <0x18>. CFA37 Component: OS_TOOLS. Category: OS. Event Tx error <0x19>. CFA43 Component: OS_TOOLS. Category: OS. Access error to the Entity at USB activation component. CFB00 Component: Panel. Category: KI-Panel. Netfront error (SLIM_E_GENERIC). CFB01 Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_DNS_INVAL). CFB02 Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_DNS_NOSERVER). CFB03 Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_DNS_TIMEDOUT). CFB04 Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_DNS_NOTFOUND). CFB05 Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_TCP_OPEN). CFB06 Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_TCP_CONNECT). CFB07 Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_TCP_READ). CFB08 Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_TCP_WRITE). CFB09 Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_SSL_CONNECT). CFB0A Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_SSL_HANDSHAKE). CFB0B Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_SSL_READ). CFB0C Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_SSL_WRITE). CFB0D Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_REQTIMEDOUT). CFB0E Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_RSPTIMEDOUT). CFB0F Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_CACHE_NONE). CFB10 Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_CACHE_EXPIRE). CFB11 Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_AUTH_UNKNOWN). CFB12 Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_AUTH_NOHEADER). CFB13 Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_AUTH_FORMAT). CFB14 Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_REDIRECT_FORMAT). CFB15 Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_REDIRECT_CANCELLED). CFB16 Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_REQ_HEADER_SIZEOVER). CFB17 Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_REQ_BODY_SIZEOVER). CFB18 Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_RSP_HEADER_SIZEOVER). CFB19 Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_REQ_TOOMANYCONTINUE). CFB1A Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_TLS_INTOLERANT). CFB1B Component: Panel. Category: KI-Panel. Netfront error (SLIM_FILEP_E_OPEN). CFB1C Component: Panel. Category: KI-Panel. Netfront error (SLIM_FILEP_E_READ). CFB1D Component: Panel. Category: KI-Panel. Netfront error (SLIM_CONTENT_E_SIZEOVER). CFB1E Component: Panel. Category: KI-Panel. Netfront error (SLIM_CONTENT_E_NO_CONTENT). CFB1F Component: Panel. Category: KI-Panel. Netfront error (SLIM_CONTENT_E_TOOMANYREDIRECT). CFB20 Component: Panel. Category: KI-Panel. Netfront error (SLIM_CONTENT_E_TOOMANYAUTH). CFB21 Component: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_NOMEMORY). CFB22 Component: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_NOMEMORY_IMAGE). CFB23 Component: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_TOTAL_SIZEOVER). CFB24 Component: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_BADURL). CFB25 Component: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_BADMIMETYPE). CFB26 Component: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_MIXEDSECURETYPE). CFB27 Component: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_INPUTHISTORY_SIZEOVER). CFB28 Component: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_INPUT_REQUIRED). CFB29 Component: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_KMC_NOTIFYMAXWINDOW). CFB2A Component: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_KMC_SWKOVERFLOW). CFB2B Component: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_KMC_FILEDOWNLOAD). CFB2C Component: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_KMC_SEGFAULT). CFB2C CFB30 CFB31 Panel Error. NetFont error. Communication error between panel and main controller during initialization or rejection of communication by controller during initialization. Blue Screen of Death. CFB30 Component: Panel. Category: KI-Panel. Failed to connect the communication of the controller when starting up. Blue back screen. Cannot enter maintenance mode. CFB30 Incompatible Level Of Firmware on Main EEPROM. CFB30 Incompatible Level Of Firmware on Main EEPROM. CFB31 Component: Panel. Category: KI-Panel. Refused to connect the communication of the controller when starting up. Blue back screen. Cannot enter maintenance mode. CFB31 Corrupt Firmware on Main EEPROM. CFB31 Corrupt Firmware on Main EEPROM. CFB32 Component: Panel. Category: KI-Panel. Time to start up request command (start up request command could not be received). Blue back screen. Cannot enter maintenance mode. CFB32 Panel Error. Timeout request for start up command. Start command hasn’t been received. Possible destruction of system file in HDD. Cannot enter maintenance mode. Blue Screen of Death. CFB33 Component: Panel. Category: KI-Panel. Cut off of the communication with the controller is detected — waiting to receive: select () OK return, recv() RX data length 0. Blue back screen. Cannot enter maintenance mode. CFB33 Panel Error. Detects disconnection with controller. Possible overdrive of control board or destruction of system file in HDD. Cannot enter maintenance mode. Blue Screen of Death. CFB34 Component: Panel. Category: KI-Panel. Time out for Response telegraphic message (could not receive response telegraphic message within a fixed time). In case on not through httpd, this error occurs (in case it does not become CGI time out). CFB35 Component: Panel. Category: KI-Panel. Received abusive command from controller. At this moment, only the case that unexpected command comes in when wating for the startup request command. CFB36 Component: Panel. Category: KI-Panel. Connection error is detected when waiting for he response telegraphic message from the controller. select () function returned the error (other than EINTR). CFB37 Component: Panel. Category: KI-Panel. Connection error is detected when waiting for he response telegraphic message from the controller. rcv () function returned the error. CFB38 Component: Panel. Category: KI-Panel. Communication error is detected when transferring (using UNIX domain) response telegraphic message in the panel. send() function returned the error (other than EINTR). CFB39 Component: Panel. Category: KI-Panel. Crucial error is detected when processing receive/transfer of the response telegraphic message from controller. Failed to acquire semafo??? CFB3A Component: Panel. Category: KI-Panel. Communication error is detected when sending required response telegraphic message from panel. send() function returned the error (other than EINTR).

1-4-7

(1) Scan to SMB error codes

Code

Display

1102

Error: User/Password or

Shared Name/Folder Name

1103

Error: Pathname or File

Name

1105

Error: Not support protocol

2101

Error: Can not connect

2103

Error: Response wait with

timeout

2201

Error: Network transfer

2203

Error: Response wait with

timeout

9181

Error: Page max count over

Causes

Domain name is not entered.

Assign disable user/pass-

word.

Assign the user who is not

allowed to access to folder.

Assign disable shared name.

Host name error.

Domain name is not enter

Connect to the folder which is

not permitted for reference/

writing.

Assign disable folder path.

SMB Protocol is set to OFF.

Enter the disable host name/

IP address.

Assign the wrong port num-

ber.

Network is not connected.

The server is unable to com-

municate.

Error occurs on the network.

Response is not returned

from the server above speci-

fied time.

The number of pages of a

send file exceeded 999

pages.

Remarks

Check procedures/corrective measures

Enter the user name with the form of either

[Domain¥User], [Domain/User] or

[Domain@User].

Enter the correct user name/password.

Enter correct user name/password.

Check the access limit of destination folder.

Enter the correct shared name.

Check if the prohibited letters below are

used to shared name.

@( )!&#$%^~[ ]`

Check if the prohibited letters are used to

shared name.

«&'( )|`;<>

Enter the user name with the form of either

[Domain¥User], [Domain/User] or

[Domain@User].

Enter correct user name/password.

Check the access limit of destination folder.

Enter correct folder path.

Check ON in the [Scanner]-[SMB] screen in

COMMAND CENTER.

Enter the correct host name or IP address.

Enter the correct port number.

Check if the server is operating properly.

Check the network connection (cable. net-

work condition within LAN, etc.).

Check if the server is operating properly.

Check the network connection (cable. net-

work condition within LAN, etc.).

Check the network connection (cable. net-

work condition within LAN, etc.).

Set the number of pages as 999 or less.

2JN

1-4-31