Severe error 0x4050002

Comment 3 dino99 2012-09-22 07:22:43 UTC
Created attachment 80691 [details]
dmesg bootlog

I'm getting some errors at boot time, since a while, on a ubuntu quantal i386 system:

prereset failed (errno -19)

then the system continue to boot. But today i get some more errors after that one:

ata2: exception Emask 0x10 SAct 0x0 SErr 0x4050002 action 0xe frozen
ata2: irq_stat 0x00000040, connection status changed
ata2: SError: { RecovComm PHYRdyChg CommWake DevExch }
ata2: hard resetting link
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.00: unsupported device, disabling
ata2.00: disabled
ata2: EH complete

note: i'm not sure thats a IO error about ide, so please feel free to change for good debug team if needed.


Comment 3


dino99



2012-09-22 07:22:43 UTC

Thats said, the system is usable at first glance.


Comment 4


Alan



2012-09-23 21:07:26 UTC

It's reporting a cable or device change. Are all the disks and CDROMs correctly seen ?


Comment 5


Reartes Guillermo



2012-09-23 21:54:09 UTC

Controller #1:

<<<< SATA controller [0106]: Intel Corporation N10/ICH7 Family SATA Controller 
[AHCI mode] [8086:27c1] (rev 01) (prog-if 01 [AHCI 1.0]) >>>

ahci 0000:00:1f.2: version 3.0
ahci 0000:00:1f.2: irq 45 for MSI/MSI-X
ahci 0000:00:1f.2: enabling ASUS P5W DH Deluxe on-board SIMG4726 workaround
ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum part 
ahci 0000:00:1f.2: setting latency timer to 64
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
ata1: SATA max UDMA/133 abar m1024@0xfebfb800 port 0xfebfb900 irq 45
ata2: SATA max UDMA/133 abar m1024@0xfebfb800 port 0xfebfb980 irq 45
ata3: SATA max UDMA/133 abar m1024@0xfebfb800 port 0xfebfba00 irq 45
ata4: SATA max UDMA/133 abar m1024@0xfebfb800 port 0xfebfba80 irq 45

Controller #2:

<<< SATA controller [0106]: JMicron Technology Corp. JMB363 SATA/IDE Controller
[197b:2363] (rev 03) (prog-if 01 [AHCI 1.0]) >>>

ahci 0000:02:00.0: AHCI 0001.0000 32 slots 2 ports 3 Gbps 0x3 impl SATA mode
ahci 0000:02:00.0: flags: 64bit ncq pm led clo pmp pio slum part 
scsi4 : ahci
scsi5 : ahci
ata5: SATA max UDMA/133 abar m8192@0xf87fe000 port 0xf87fe100 irq 17
ata6: SATA max UDMA/133 abar m8192@0xf87fe000 port 0xf87fe180 irq 17

Controller #3:

<<<  IDE interface [0101]: Intel Corporation 82801G (ICH7 Family) IDE Controller
[8086:27df] (rev 01) (prog-if 8a [Master SecP PriP]) >>>

ata_piix 0000:00:1f.1: version 2.13
ata_piix 0000:00:1f.1: setting latency timer to 64
scsi6 : ata_piix
scsi7 : ata_piix
ata7: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
ata8: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15

Controller #4 (PATA, SAME CARD as #2):

<<< IDE interface [0101]: JMicron Technology Corp. JMB363 SATA/IDE Controller
[197b:2363] (rev 03) (prog-if 85 [Master SecO PriO]) >>>

pata_acpi 0000:02:00.1: enabling device (0000 -> 0001)
pata_acpi 0000:02:00.1: setting latency timer to 64
scsi8 : pata_acpi
scsi9 : pata_acpi
ata9: PATA max UDMA/133 cmd 0xac00 ctl 0xa880 bmdma 0xa400 irq 18
ata10: PATA max UDMA/133 cmd 0xa800 ctl 0xa480 bmdma 0xa408 irq 18

ERRORS:

* ata2.00: failed to IDENTIFY (I/O error, err_mask=0x100)

* ata2.00: unsupported device, disabling

* ata10: prereset failed (errno=-19)
  ata10: reset failed, giving up

WARNINGS:

* WARNING#1: (For ATA6 & ATA7)

  pci 0000:02:00.0: disabling ASPM on pre-1.1 PCIe device.  You can enable it with 'pcie_aspm=force'

  
* WARNING#2: 

  pci0000:00: ACPI _OSC support notification failed, disabling PCIe ASPM
  pci0000:00: Unable to request _OSC control (_OSC support mask: 0x08)

    
* WARNING#3: 

  ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
  ata2.00: failed to IDENTIFY (I/O error, err_mask=0x100)
  ata2: SATA link down (SStatus 0 SControl 300)

  ata2: exception Emask 0x10 SAct 0x0 SErr 0x4050002 action 0xe frozen
  ata2: irq_stat 0x00000040, connection status changed
  ata2: SError: { RecovComm PHYRdyChg CommWake DevExch }
  ata2: hard resetting link
  ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
  ata2.00: unsupported device, disabling
  ata2.00: disabled
  ata2: EH complete

* WARNING#4:

  ata10: prereset failed (errno=-19)
  ata10: reset failed, giving up

* WARNING#5:

  ACPI: Invalid Power Resource to register!

  ACPI Warning: 0x00000295-0x00000296 SystemIO conflicts with Region _SB_.PCI0.SBRG.SIOR.HWRE 1 (20120711/utaddress-251)
  ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver

  ACPI Warning: 0x00000480-0x000004bf SystemIO conflicts with Region _SB_.PCI0.SBRG.GPIO 1 (20120711/utaddress-251)
  ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver

------------------------------------------------
  
What device is attached to ata2 and ata10?


Comment 7


Alan



2012-09-24 09:12:44 UTC

I missed the menu entry 8-)
Источник

I’m getting following error message at the system boot up. The system takes long time to start and I could not understand what it’s saying and why. The os has recently been installed(3 weeks ago). The following are the last few line of /var/log/dmesg file. Please any one let me know if it could be resolved. Thank you!

[   10.049830] type=1505 audit(1295344306.586:13): operation="profile_replace" pid=850 name=/usr/share/gdm/guest-session/Xsession
[   10.051165] type=1505 audit(1295344306.586:14): operation="profile_replace" pid=851 name=/sbin/dhclient3
[   10.051744] type=1505 audit(1295344306.586:15): operation="profile_replace" pid=851 name=/usr/lib/NetworkManager/nm-dhcp-client.action
[   10.052058] type=1505 audit(1295344306.590:16): operation="profile_replace" pid=851 name=/usr/lib/connman/scripts/dhclient-script
[   10.055205] type=1505 audit(1295344306.590:17): operation="profile_replace" pid=852 name=/usr/bin/evince
[   10.064843] type=1505 audit(1295344306.602:18): operation="profile_replace" pid=852 name=/usr/bin/evince-previewer
[   10.070323] type=1505 audit(1295344306.606:19): operation="profile_replace" pid=852 name=/usr/bin/evince-thumbnailer
[   10.078696] type=1505 audit(1295344306.614:20): operation="profile_replace" pid=854 name=/usr/lib/cups/backend/cups-pdf
[   10.079377] type=1505 audit(1295344306.614:21): operation="profile_replace" pid=854 name=/usr/sbin/cupsd
[   10.081306] type=1505 audit(1295344306.618:22): operation="profile_replace" pid=855 name=/usr/sbin/mysqld
[   19.476007] eth0: no IPv6 routers present
[   42.816048] ata3: lost interrupt (Status 0x50)
[   42.816073] ata3.00: exception Emask 0x10 SAct 0x0 SErr 0x4850002 action 0xe frozen
[   42.816162] ata3: SError: { RecovComm PHYRdyChg CommWake LinkSeq DevExch }
[   42.816229] ata3.00: cmd c8/00:20:f7:2c:a0/00:00:00:00:00/e2 tag 0 dma 16384 in
[   42.816230]          res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x14 (ATA bus error)
[   42.816311] ata3.00: status: { DRDY }
[   42.816337] ata3: hard resetting link
[   43.700050] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[   43.732364] ata3.00: configured for UDMA/133
[   43.732371] ata3.00: device reported invalid CHS sector 0
[   43.732381] ata3: EH complete
[   74.804023] ata3: lost interrupt (Status 0x50)
[   74.804049] ata3.00: exception Emask 0x10 SAct 0x0 SErr 0x40d0002 action 0xe frozen
[   74.804137] ata3: SError: { RecovComm PHYRdyChg CommWake 10B8B DevExch }
[   74.804217] ata3.00: cmd c8/00:20:9f:a6:a1/00:00:00:00:00/e2 tag 0 dma 16384 in
[   74.804218]          res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x14 (ATA bus error)
[   74.804296] ata3.00: status: { DRDY }
[   74.804322] ata3: hard resetting link
[   75.684548] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[   75.716346] ata3.00: configured for UDMA/133
[   75.716353] ata3.00: device reported invalid CHS sector 0
[   75.716363] ata3: EH complete
[  106.804020] ata3: lost interrupt (Status 0x50)
[  106.804045] ata3.00: exception Emask 0x10 SAct 0x0 SErr 0x4050002 action 0xe frozen
[  106.804132] ata3: SError: { RecovComm PHYRdyChg CommWake DevExch }
[  106.804209] ata3.00: cmd c8/00:18:87:c0:cc/00:00:00:00:00/e1 tag 0 dma 12288 in
[  106.804210]          res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x14 (ATA bus error)
[  106.804288] ata3.00: status: { DRDY }
[  106.804313] ata3: hard resetting link
[  107.684547] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[  107.716346] ata3.00: configured for UDMA/133
[  107.716352] ata3.00: device reported invalid CHS sector 0
[  107.716362] ata3: EH complete
[  138.804019] ata3: lost interrupt (Status 0x50)
[  138.804043] ata3: limiting SATA link speed to 1.5 Gbps
[  138.804050] ata3.00: exception Emask 0x10 SAct 0x0 SErr 0x40d0002 action 0xe frozen
[  138.804137] ata3: SError: { RecovComm PHYRdyChg CommWake 10B8B DevExch }
[  138.804215] ata3.00: cmd c8/00:10:07:42:aa/00:00:00:00:00/e2 tag 0 dma 8192 in
[  138.804216]          res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x14 (ATA bus error)
[  138.804294] ata3.00: status: { DRDY }
[  138.804320] ata3: hard resetting link
[  139.684548] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[  139.716341] ata3.00: configured for UDMA/133
[  139.716348] ata3.00: device reported invalid CHS sector 0
[  139.716358] ata3: EH complete
[  170.804017] ata3: lost interrupt (Status 0x50)
[  170.804041] ata3.00: exception Emask 0x10 SAct 0x0 SErr 0x48d0002 action 0xe frozen
[  170.804129] ata3: SError: { RecovComm PHYRdyChg CommWake 10B8B LinkSeq DevExch }
[  170.804214] ata3.00: cmd c8/00:20:97:1a:20/00:00:00:00:00/e2 tag 0 dma 16384 in
[  170.804215]          res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x14 (ATA bus error)
[  170.804293] ata3.00: status: { DRDY }
[  170.804319] ata3: hard resetting link
[  171.684548] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[  171.716360] ata3.00: configured for UDMA/133
[  171.716367] ata3.00: device reported invalid CHS sector 0
[  171.716377] ata3: EH complete
[  203.804025] ata3: lost interrupt (Status 0x50)
[  203.804051] ata3.00: exception Emask 0x10 SAct 0x0 SErr 0x48d0002 action 0xe frozen
[  203.804141] ata3: SError: { RecovComm PHYRdyChg CommWake 10B8B LinkSeq DevExch }
[  203.804222] ata3.00: cmd c8/00:08:6f:44:81/00:00:00:00:00/e0 tag 0 dma 4096 in
[  203.804223]          res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x14 (ATA bus error)
[  203.804302] ata3.00: status: { DRDY }
[  203.804328] ata3: hard resetting link
[  204.684051] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[  204.716357] ata3.00: configured for UDMA/133
[  204.716363] ata3.00: device reported invalid CHS sector 0
[  204.716373] ata3: EH complete

Jorge Castro's user avatar

Jorge Castro

70k123 gold badges462 silver badges652 bronze badges

asked Jan 18, 2011 at 11:10

user3215's user avatar

4

This looks to be a harddrive error(because of ATA errors). What worked for me when I had an error like this is loading to a bootable cd and runing 

fsck /dev/sda1

This fix the filesystem problem which was preventing my friends system from booting.

I would also run smart test on the drive to see if it needs replacing.

answered Jan 18, 2011 at 22:29

Matt Mootz's user avatar

Matt MootzMatt Mootz

5693 silver badges10 bronze badges

2

I can only guess that the issue is hardware related since the log shows very terminal errors contacting the disk. Check your computer’s internal connections.

If it’s not that, then you have serious issues which need to be reported as bugs (but check cables first). There is no answer really to such issues as if it is a bug, it just needs to be fixed by someone. See here for details:

https://help.ubuntu.com/community/ReportingBugs

answered Jan 18, 2011 at 15:03

Martin Owens -doctormo-'s user avatar

4

Источник

Перейти к содержимому раздела

Форумы CADUser

Информационный портал для профессионалов в области САПР

Вы не вошли. Пожалуйста, войдите или зарегистрируйтесь.

Дерево сообщений Активные темы Темы без ответов

Страницы 1

Чтобы отправить ответ, вы должны войти или зарегистрироваться

#1 13 апреля 2004г. 14:04:00

  • Vladimir
  • Восстановленный участник
  • На форуме с 13 апреля 2004г.
  • Сообщений: 1
  • Спасибо: 0

Тема: Как почистить сервис-станцию? (HP DJ 500)

Плоттер HP DJ 500 при включении выдает ошибку :
System Error 21:10
После нажатия клавиши «меню» выдается сообщение:
System Error
Severe Error : 0x3010002
task: t Mech
File: sequence.c
Line: 758
Посоветовали почистить сервис станцию.
Если у кого была такая неисправность, подскажите а где она находится и что там нужно чистить?

#2 Ответ от Stas-Karabas 16 августа 2006г. 12:06:25

  • Stas-Karabas
  • Восстановленный участник
  • На форуме с 16 августа 2006г.
  • Сообщений: 1
  • Спасибо: 0

Re: Как почистить сервис-станцию? (HP DJ 500)

Такая же проблема у меня, и никто незнает блин

#3 Ответ от Геннадий aka PG 16 августа 2006г. 13:15:21

  • Геннадий aka PG
  • Восстановленный участник
  • На форуме с 4 апреля 2002г.
  • Сообщений: 1,348
  • Спасибо: 0

Re: Как почистить сервис-станцию? (HP DJ 500)

This is a Service station error. Check for obstructions in the service station on the right.
Turn on the printer in service mode by holding down the UP arrow and ENTER keys (simultaniously).
Enter Service Utilities, choose Unlock Carriage. Turn the printer off and move the carriage to
the center of the printer. Turn the printer back on. The carriage and service station should
return to their home positions.
If the error returns on power-on, the service station will probably need to be replaced.
Parts and diagrams can be found at partsurfer.hp.com.
http://h41186.www4.hp.com/country/us/en … R1002_USEN

#4 Ответ от Евгений 13 октября 2006г. 09:33:10

  • Евгений
  • Восстановленный участник
  • На форуме с 13 октября 2006г.
  • Сообщений: 2
  • Спасибо: 0

Re: Как почистить сервис-станцию? (HP DJ 500)

у меня была эта ошибка. залило краской. картридж потек и залило там под этой лабудой оптопары. снял крышкуку окуратно разобрав саму станцию почистил оптопары и все гут работает.

#5 Ответ от Алексей 22 ноября 2006г. 15:18:43

  • Алексей
  • Восстановленный участник
  • На форуме с 22 ноября 2006г.
  • Сообщений: 1
  • Спасибо: 0

Re: Как почистить сервис-станцию? (HP DJ 500)

Можно ли заправлять катриджи для плоттера НР 500,если да, то есть ли другие виды красок которые совместимы с родными?

Сообщения 5

Тему читают: 1 гость

Страницы 1

Чтобы отправить ответ, вы должны войти или зарегистрироваться

Источник

Понравилась статья? Поделить с друзьями:
  • Sims 2 как изменить стремление
  • Sim error 3005 rw error 00000080
  • Severe error 0x3010004
  • Siemens lme73 000a2 коды ошибок
  • Sim error 203f