KESS(клон) EMS3132 ошибка WAKE UP ERROR — ChipTuner Forum
Чип-тюнинг коммерческой техники Кама3, ГАЗ от SMS-Soft
Прошивки Hyundai SIM2K-24x от Argutin Motors | Прошивки M86 и Гранта M74M от Argutin Motors | Прошивки Kia SIM2K-24x и Bosch ME17.9.21 от Argutin Motors | Прошивки M74-RCO ВАЗ от Владимира Башкирова |
KESS(клон) EMS3132 ошибка WAKE UP ERROR
-
offline
Слесарь
- Регистрация:
- 07.01.2018
- Сообщений:
- 14
- Адрес:
- Деревня Дёмино
Всем здравствуйте, уважаемые. Приобрел KESS 5.017. При подключении к вито 638 EDC15 без проблем вычитал ID и ФЛЭШ (через ОБД). При подключении к логану EMS3132 (к трем машинам с таким блоком) одинаково выскакивает ошибка WAKE UP ERROR, при считывании ID.протокол 34. Китаец выслал драйвера, проги и т.д., переустановка плодов не принесла. Форматировал карту SD, заливал туда заново образ, также результата ноль. Возможно, кто то сталкивался с проблемой и направит меня в правильное русло. Спасибо за внимание.
-
Авторемонт
- Регистрация:
- 28.08.2013
- Сообщений:
- 3,140
- Адрес:
- Волгоград
А что техподдержка говорит?
-
offline
Слесарь
- Регистрация:
- 07.01.2018
- Сообщений:
- 14
- Адрес:
- Деревня Дёмино
Техподдержка от китайца — китайская техподдержка, а именно «Китаец выслал драйвера, проги и т.д». Попросил переустановить — не помогло, сегодня написал ему снова, жду ответа. Думаю надеяться не стоит, поэтому параллельно решил попросить помощи у товарищей.
-
Авторемонт
- Регистрация:
- 28.08.2013
- Сообщений:
- 3,140
- Адрес:
- Волгоград
Купите наш модуль ЕМС3132 и будет вам счастье! И тех поддержка на высоком уровне!
-
offline
Диагностика и ремонт
- Регистрация:
- 12.08.2020
- Сообщений:
- 162
- Адрес:
- Респ.Крым
Вот те раз… Нужно лог им (ему) скинуть, он просто скорее всего не понимает всей ситуации, Алиентеков можно в копию поставить
-
offline
Слесарь
- Регистрация:
- 07.01.2018
- Сообщений:
- 14
- Адрес:
- Деревня Дёмино
Не спорю, так проще. Спасибо за предложение. Те три машины я прошил на столе, в БСЛ, комбиком. Я не ленивый, сниму и разберу блок))). Просто все шьют кессом их легко, а мой не может)))…странно
-
offline
Слесарь
- Регистрация:
- 07.01.2018
- Сообщений:
- 14
- Адрес:
- Деревня Дёмино
думаете лог кривой или он отсутствует?
-
offline
Слесарь
- Регистрация:
- 07.01.2018
- Сообщений:
- 14
- Адрес:
- Деревня Дёмино
Полностью с вами согласен. Загрузчик есть-комбик. но кесс работает с этим блоком и этим я хотел удостоверится что SD живая, фильтра живые, припой на проце есть и т.д..где то затаилась программная неисправность…но это не точно.
Последний раз редактировалось sergey_tesak; 19.09.2022 в 00:31. -
offline
диагност-автоэлектрик
- Регистрация:
- 21.03.2010
- Сообщений:
- 646
- Адрес:
- Kazan
Это говорит о том, что прибор не получил нужных данных…
-
offline
Инженер
- Регистрация:
- 24.04.2010
- Сообщений:
- 1,406
- Адрес:
- Ульяновск
Какую версию используете 2.47?
-
offline
Слесарь
- Регистрация:
- 07.01.2018
- Сообщений:
- 14
- Адрес:
- Деревня Дёмино
2.8 ….Но перед этим устанавливал 2.23…по мануалу
-
offline
диагност-автоэлектрик
- Регистрация:
- 21.03.2010
- Сообщений:
- 646
- Адрес:
- Kazan
Через дачию попробуйте…
-
offline
Слесарь
- Регистрация:
- 07.01.2018
- Сообщений:
- 14
- Адрес:
- Деревня Дёмино
я Вас понял…пробовал…аналогично….посоветовали L-линию проверить в кабеле….вечером прозвоню….только вроде шьется по K-линии…возможно я что-то не понимаю и не знаю..
-
авто-диагност
- Регистрация:
- 16.05.2009
- Сообщений:
- 7,822
- Адрес:
- г.Кисловодск
Помнится был пакет библиотек на кесс, под какие машины не помню, но вроде под французов.
-
offline
Диагност
- Регистрация:
- 26.06.2014
- Сообщений:
- 10,007
- Адрес:
- Ярославль
Жека, там были длл для контролек.
-
авто-диагност
- Регистрация:
- 16.05.2009
- Сообщений:
- 7,822
- Адрес:
- г.Кисловодск
-
offline
Автодиагност
- Регистрация:
- 21.02.2006
- Сообщений:
- 13,486
- Адрес:
- Липецкая обл. г.Елец
wake up error это про CAN
наверное пытаетесь прошить K-line блок протоколом под CAN -
offline
Слесарь
- Регистрация:
- 07.01.2018
- Сообщений:
- 14
- Адрес:
- Деревня Дёмино
Да нет. 34 протокол…как обычно…
-
offline
Автодиагност
- Регистрация:
- 08.10.2020
- Сообщений:
- 188
- Адрес:
- Безенчук
Гуглить, яндексить, yahooить, использовать MSN, байду и Гопхер (Gopher) в конце концов попробовали ?
Первая ссылка в гугле на возможные проблемы и пути решения (https://blog.uobdii.com/how-to-solve…wake-up-error/ https://www.obdii365.com/upload/serv…e-up-error.pdf). Одна из частых причин плохой контакт в слоте TF карты, файлов нав TF картедиректории кесса не хватает, «разболтался» чип, не та версия ОС, не та версия оболочки кесса. Там в кессе вставлена карта чтоли ? -
offline
Диагностика и ремонт
- Регистрация:
- 12.08.2020
- Сообщений:
- 162
- Адрес:
- Респ.Крым
Крутая тема на специализированном форуме — «Почему отлом не хочет работать как положено»… Повеяло драйв2…
-
offline
Слесарь
- Регистрация:
- 07.01.2018
- Сообщений:
- 14
- Адрес:
- Деревня Дёмино
Пробовал, пробую до сих пор «Гуглить, яндексить, yahooить, использовать MSN, байду и Гопхер (Gopher)»…все перепробовал эти стандартные неисправности….и карту форматировал и клонировал и перезаписывал и т.д….разбираюсь……пока остановился на том, что виной ПК — ОС, Virtual C++ или дрова…..пока нет времени переустанавливть…
-
offline
диагност-автоэлектрик
- Регистрация:
- 21.03.2010
- Сообщений:
- 646
- Адрес:
- Kazan
Еще раз: с неподключенным разьемом обд будет то же самое. Это как намек.))
-
5th November, 2019, 09:32 PM
#1
Kess v2 5.017 wake up error need help or advice
Hello everyone,i have red pcb kess v2 5.017 china clone,it worked well for few years on all ecus,did not had any problems,but past weeks i tryed on some ecus on VAG cars,for example vw edc17cp14 or audi edc16cp34 can’t event make id no matter what i try,no matter or i choose kline(min or max speed) or CAN, first it says unknown ecu and than wake up error,but previausly it worked good with these same cars or/and ecus,looks like it sometimes work sometimes not,can someone help me to try figure out how to solve this problem?I tryed sw 2.23 and 2.47,different usb ports,reinstaled drivers and still the same.Maybe make new sd card or format existing sd card?I tryed to lift and clean sd card slot pins on pcb,but it did not help.Different tools like fgtech or mpps get id,read or write from the first time smoothly on same cars.
Last edited by arejas; 5th November, 2019 at 09:43 PM.
-
6th November, 2019, 05:49 PM
#2
Originally Posted by arejas
Hello everyone,i have red pcb kess v2 5.017 china clone,it worked well for few years on all ecus,did not had any problems,but past weeks i tryed on some ecus on VAG cars,for example vw edc17cp14 or audi edc16cp34 can�t event make id no matter what i try,no matter or i choose kline(min or max speed) or CAN, first it says unknown ecu and than wake up error,but previausly it worked good with these same cars or/and ecus,looks like it sometimes work sometimes not,can someone help me to try figure out how to solve this problem?I tryed sw 2.23 and 2.47,different usb ports,reinstaled drivers and still the same.Maybe make new sd card or format existing sd card?I tryed to lift and clean sd card slot pins on pcb,but it did not help.Different tools like fgtech or mpps get id,read or write from the first time smoothly on same cars.
Buy a new brand quality micro sd (2-4gb) and do this….https://www.digital-kaos.co.uk/forums/showthread.php/713605-Kess-5-017-how-to-read-SD-card-or-create-a-new-SD-card?p=3645247&viewfull=1#post3645247https://www.digital-kaos.co.uk/forum…-a-new-SD-card
-
The Following 2 Users Say Thank You to gas43 For This Useful Post:
arejas (9th November, 2019), chentron (6th November, 2019)
-
6th November, 2019, 07:15 PM
#3
Originally Posted by arejas
Hello everyone,i have red pcb kess v2 5.017 china clone,it worked well for few years on all ecus,did not had any problems,but past weeks i tryed on some ecus on VAG cars,for example vw edc17cp14 or audi edc16cp34 can�t event make id no matter what i try,no matter or i choose kline(min or max speed) or CAN, first it says unknown ecu and than wake up error,but previausly it worked good with these same cars or/and ecus,looks like it sometimes work sometimes not,can someone help me to try figure out how to solve this problem?I tryed sw 2.23 and 2.47,different usb ports,reinstaled drivers and still the same.Maybe make new sd card or format existing sd card?I tryed to lift and clean sd card slot pins on pcb,but it did not help.Different tools like fgtech or mpps get id,read or write from the first time smoothly on same cars.
replace DLLs and test
-
7th November, 2019, 04:20 AM
#4
I had same problem no id, «warning unknown ecu». But only on vag cars. Try to read even if error appears.
-
7th November, 2019, 05:41 PM
#5
So maybe first i try replace sd card and than dlls and see how it goes,thank you!
-
7th November, 2019, 05:57 PM
#6
Originally Posted by arejas
So maybe first i try replace sd card and than dlls and see how it goes,thank you!
start with the most basic DLL and try
-
9th November, 2019, 10:24 AM
#7
Thanks for everybody,DLL’s did not help,but new premium SD Card solved wakeup error issue and gave more speed for making tasks for kess,tool working again with no wakeup error,!
So if some VAG or other ecus gives you wake up error or just randomly work/not work
1. Try re-copy-paste «fresh» DLL files to ksuite folder/DLL
2. Open your kess main unit and remove old sd card,lift sdcard slot pins and clean slot and sd card contacts with alchogol and make sure sd card slot soldered well to PCB
3. Buy new premium brand sd card and make new kess files for your sd card,use forum search for tutorials in the forum. Very easy to do.
If this didn’t help,need to rework PCB or buy new tool.Last edited by arejas; 9th November, 2019 at 10:34 AM.
-
9th November, 2019, 02:18 PM
#8
You could do a small tutorial, as you solved the issue, in relation to the premium SD card and file copy.
-
9th November, 2019, 02:36 PM
#9
The KESS Clone only works on older kind of cars and ecu’s.
from 2009 and up the kess doesnt work.
You can try all you want but wont work.Buy real tuning tools like CMD, BDM, ,magic motorsports
-
9th November, 2019, 02:48 PM
#10
Originally Posted by RBTuning
The KESS Clone only works on older kind of cars and ecu’s.
from 2009 and up the kess doesnt work.
You can try all you want but wont work.Buy real tuning tools like CMD, BDM, ,magic motorsports
I have occupied KESS 2.47 RED PCB FW 7.020 in vehicles until 2014 for example the last one was a HYUNDAI NEW H1 with ecu DELPHI DCM3.7AP without any problem.
-
The Following User Says Thank You to systemlinux For This Useful Post:
gas43 (9th November, 2019)
-
9th November, 2019, 06:35 PM
#11
Originally Posted by RBTuning
The KESS Clone only works on older kind of cars and ecu’s.
from 2009 and up the kess doesnt work.
You can try all you want but wont work.Buy real tuning tools like CMD, BDM, ,magic motorsports
I can not say that you are not right,but i know few people who have kess v2 clone and it works good with all protocols,even on cars till 2017,it all depends of the car and what type of ecu it uses.
I can say it can make 99% of cars wich we see on the roadsLast edited by arejas; 9th November, 2019 at 06:38 PM.
-
9th November, 2019, 06:41 PM
#12
Originally Posted by systemlinux
You could do a small tutorial, as you solved the issue, in relation to the premium SD card and file copy.
I did small tutorial,and for new sd card i used «gas43» user provided links on top of this thread,so i don’t need to double post it.
-
The Following User Says Thank You to arejas For This Useful Post:
gas43 (9th November, 2019)
-
19th November, 2019, 01:11 PM
#13
Update:
After 1 week of usage,on audi q7 2007 yr 3.0tdi 155kw edc17cp04,identical same problem again(can’t make id),now even on edc16 ID does not work anymore,even it worked perfect for one week with new sdcard and new files.
Don’t think that sd card failed again.
Anyone can recommend good reable kess/ktag rework seller?Last edited by arejas; 19th November, 2019 at 01:48 PM.
-
19th November, 2019, 02:37 PM
#14
Try one more time to create the micro sd….
Are you sure that your micro sd is quality?
-
19th November, 2019, 02:57 PM
#15
Originally Posted by gas43
Try one more time to create the micro sd….
Are you sure that your micro sd is quality?I will try to make new files on same SDcard and test,see if it helps.
My sd card is Verbatim Premium SDHC 16GB Class 10,read speed up to 80MB/s ,Water,Shock and Temperature resistant.Last edited by arejas; 19th November, 2019 at 11:02 PM.
If you get “Wake up error” when running KESS V2 V5.017, please format the TF card firstly and then copy the whole software again back to TF card, finally to reflashing the CPU program.
Details as follows:
Tips on how to copy files to TF card:
Step 1: receive the “kess v2 up” compressed file from us online.
Step 2: decompress it, and you will find 4 files: File, Log, System and Update, choose them all, copy and paste to TF card. (IMPORTANT NOTE: Don’t directly copy the “kess v2 up” compressed file to TF card; Don’t create a new folder in TF card and copy the 4 files into the new folder.)
(Fig 1. Compressed file: kessv2 up)
(Fig 1. decompress Auto ECU Programmer kessv2 up.rar)
Possible reasons and solutions:
Possible reasons:
Kess v2 ecu chip tuning tool fails to read out TF card program or the program in the TF card is not working.
There are 2 reasons result in Kess v2 fails to read out TF card program.
1) The four pins of chip are not firmly soldered on the main board.
2) The chip is disconnected to the main board for a long time use.
Solution:
Solder again the chip; make sure it is tightly connected to the main board. If it is not the chip problem, do the following jobs.
Use brush to clean up the shrapnel on the card slot.
Maybe the card slot shrapnel is not flexible enough; use something like a needle to lift it up, to make sure the shrapnel and the TF card is well connected.
Remove the TF card and clean up it, then insert back to the card slot. If it is still not working, format the card and copy the software back to the card.
Finally, reflash the CPU program, after finish reflashing, copy and paste the software to the TF card again.
Free download kess v2 firmware tuning kit
Now, KESS V2 chip tuning wake up error is solved
Our customers feedback some problem about kess v2 on OBD2TOOL,we sovled it and have written below,if you have same problems,it will help you.
- car kess v2
- ecu tuning kit
- K-TAG
- K-TAG ECU Programming
- Kess V2
- Kess V2 Online Version
- KESS V2 V5.017
- KTAG
- KTAG ECU Programmer
- KTAG KTM100
- KTAG Master
- KTAG Programming tool
- ktag v2.23
- KTAG V7.020
- KTM100 KTAG
- ktm100 v2.23
- Latest KTAG ECU Programmer
- truck kess v2
- V2.23 Kess V2